- 27 Jan, 2015 38 commits
-
-
Martin K. Petersen authored
commit 198a956a upstream. The Microsoft iSCSI target does not support REPORT SUPPORTED OPERATION CODES. Blacklist these devices so we don't attempt to send the command. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Tested-by:
Mike Christie <michaelc@cs.wisc.edu> Reported-by: jazz@deti74.ru Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sreekanth Reddy authored
commit 2311ce4d upstream. This reverts commit 963ba22b ("mpt3sas: Remove phys on topology change") Reverting the previous mpt3sas drives patch changes, since we will observe below issue Issue: Drives connected Enclosure/Expander will unregister with SCSI Transport Layer, if any one remove and add expander cable with in DMD (Device Missing Delay) time period or even any one power-off and power-on the Enclosure with in the DMD period. Signed-off-by:
Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
-
Sreekanth Reddy authored
commit 81a89c2d upstream. This reverts commit 3520f9c7 ("mpt2sas: Remove phys on topology change") Reverting the previous mpt2sas drives patch changes, since we will observe below issue Issue: Drives connected Enclosure/Expander will unregister with SCSI Transport Layer, if any one remove and add expander cable with in DMD (Device Missing Delay) time period or even any one power-off and power-on the Enclosure with in the DMD period. Signed-off-by:
-
Nicholas Bellinger authored
commit 6bf6ca75 upstream. This patch changes iscsit_do_tx_data() to fail on short writes when kernel_sendmsg() returns a value different than requested transfer length, returning -EPIPE and thus causing a connection reset to occur. This avoids a potential bug in the original code where a short write would result in kernel_sendmsg() being called again with the original iovec base + length. In practice this has not been an issue because iscsit_do_tx_data() is only used for transferring 48 byte headers + 4 byte digests, along with seldom used control payloads from NOPIN + TEXT_RSP + REJECT with less than 32k of data. So following Al's audit of iovec consumers, go ahead and fail the connection on short writes for now, and remove the bogus logic ahead of his proper upstream fix. Reported-by:
Al Viro <viro@zeniv.linux.org.uk> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Thomas Gleixner authored
commit c291ee62 upstream. Since the rework of the sparse interrupt code to actually free the unused interrupt descriptors there exists a race between the /proc interfaces to the irq subsystem and the code which frees the interrupt descriptor. CPU0 CPU1 show_interrupts() desc = irq_to_desc(X); free_desc(desc) remove_from_radix_tree(); kfree(desc); raw_spinlock_irq(&desc->lock); /proc/interrupts is the only interface which can actively corrupt kernel memory via the lock access. /proc/stat can only read from freed memory. Extremly hard to trigger, but possible. The interfaces in /proc/irq/N/ are not affected by this because the removal of the proc file is serialized in procfs against concurrent readers/writers. The removal happens before the descriptor is freed. For architectures which have CONFIG_SPARSE_IRQ=n this is a non issue as the descriptor is never freed. It's merely cleared out with the irq descriptor lock held. So any concurrent proc access will either see the old correct value or the cleared out ones. Protect the lookup and access to the irq descriptor in show_interrupts() with the sparse_irq_lock. Provide kstat_irqs_usr() which is protecting the lookup and access with sparse_irq_lock and switch /proc/stat to use it. Document the existing kstat_irqs interfaces so it's clear that the caller needs to take care about protection. The users of these interfaces are either not affected due to SPARSE_IRQ=n or already protected against removal. Fixes: 1f5a5b87 "genirq: Implement a sane sparse_irq allocator" Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Thomas Gleixner authored
commit a5fd9733 upstream. commit 4dbd2771 "tick: export nohz tick idle symbols for module use" was merged via the thermal tree without an explicit ack from the relevant maintainers. The exports are abused by the intel powerclamp driver which implements a fake idle state from a sched FIFO task. This causes all kinds of wreckage in the NOHZ core code which rightfully assumes that tick_nohz_idle_enter/exit() are only called from the idle task itself. Recent changes in the NOHZ core lead to a failure of the powerclamp driver and now people try to hack completely broken and backwards workarounds into the NOHZ core code. This is completely unacceptable and just papers over the real problem. There are way more subtle issues lurking around the corner. The real solution is to fix the powerclamp driver by rewriting it with a sane concept, but that's beyond the scope of this. So the only solution for now is to remove the calls into the core NOHZ code from the powerclamp trainwreck along with the exports. Fixes: d6d71ee4 "PM: Introduce Intel PowerClamp Driver" Signed-off-by:
-
Dominique Leuenberger authored
commit 6583659e upstream. HP ZBook 15 laptop needs a non-standard mapping (x_inverted). BugLink: http://bugzilla.opensuse.org/show_bug.cgi?id=905329Signed-off-by:
Dominique Leuenberger <dimstar@opensuse.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Signed-off-by:
-
Jouni Malinen authored
commit 08f6f147 upstream. The VHT supported channel width field is a two bit integer, not a bitfield. cfg80211_chandef_usable() was interpreting it incorrectly and ended up rejecting 160 MHz channel width if the driver indicated support for both 160 and 80+80 MHz channels. Fixes: 3d9d1d66 ("nl80211/cfg80211: support VHT channel configuration") (however, no real drivers had 160 MHz support it until 3.16) Signed-off-by:
Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Arik Nemtsov authored
commit 34f05f54 upstream. In the already-set and intersect case of a driver-hint, the previous wiphy regdomain was not freed before being reset with a copy of the cfg80211 regdomain. Signed-off-by:
Arik Nemtsov <arikx.nemtsov@intel.com> Acked-by:
Luis R. Rodriguez <mcgrof@suse.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit 70dcec5a upstream. This can happen and there is no point in added more detection code lower in the stack. Catching these in one single point (cfg80211) is enough. Stop WARNING about this case. This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=89001 Fixes: 2f1c6c57 ("cfg80211: process non country IE conflicting first") Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Vineet Gupta authored
commit ec7ac6af upstream. With commit 9df62f05 "arch: use ASM_NL instead of ';'" the generic macros can handle the arch specific newline quirk. Hence we can get rid of ARC asm macros and use the "C" style macros. Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Vineet Gupta authored
commit e8ef060b upstream. This allows the sdplite/Zebu images to run on OSCI simulation platform Signed-off-by:
-
Chris Wilson authored
commit add284a3 upstream. In order to act as a full command barrier by itself, we need to tell the pipecontrol to actually stall the command streamer while the flush runs. We require the full command barrier before operations like MI_SET_CONTEXT, which currently rely on a prior invalidate flush. References: https://bugs.freedesktop.org/show_bug.cgi?id=83677 Cc: Simon Farnsworth <simon@farnz.org.uk> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Chris Wilson authored
commit 148b83d0 upstream. In the gen7 pipe control there is an extra bit to flush the media caches, so let's set it during cache invalidation flushes. v2: Rename to MEDIA_STATE_CLEAR to be more inline with spec. Cc: Simon Farnsworth <simon@farnz.org.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Ilia Mirkin authored
commit 4761703b upstream. Several users have, over time, reported issues with MSI on these IGPs. They're old, rarely available, and MSI doesn't provide such huge advantages on them. Just disable. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87361 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74492 Fixes: fa8c9ac7 ("drm/nv4c/mc: nv4x igp's have a different msi rearm register") Signed-off-by:
Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Chris Wilson authored
commit 2b387059 upstream. In all likelihood we will do a few hundred errnoneous register operations if we do a single invalid register access whilst the device is suspended. As each instance causes a WARN, this floods the system logs and can make the system unresponsive. The warning was first introduced in commit b2ec142c Author: Paulo Zanoni <paulo.r.zanoni@intel.com> Date: Fri Feb 21 13:52:25 2014 -0300 drm/i915: call assert_device_not_suspended at gen6_force_wake_work and despite the claims the WARN is still encountered in the wild today. Signed-off-by:
-
Daniel Vetter authored
commit 0b6d24c0 upstream. Apparently stuff works that way on those machines. I agree with Chris' concern that this is a bit risky but imo worth a shot in -next just for fun. Afaics all these machines have the pci resources allocated like that by the BIOS, so I suspect that it's all ok. This regression goes back to commit eaba1b8f Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Thu Jul 4 12:28:35 2013 +0100 drm/i915: Verify that our stolen memory doesn't conflict Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76983 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71031Tested-by:
lu hua <huax.lu@intel.com> Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Tested-by:
Paul Menzel <paulepanter@users.sourceforge.net> Signed-off-by:
-
Alex Deucher authored
commit 410cce2a upstream. The check was already in place in the dp mode_valid check, but radeon_dp_get_dp_link_clock() never returned the high clock mode_valid was checking for because that function clipped the clock based on the hw capabilities. Add an explicit check in the mode_valid function. bug: https://bugs.freedesktop.org/show_bug.cgi?id=87172Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 5e5c21ca upstream. Check the that ring we are using for copies is functional rather than the GFX ring. On newer asics we use the DMA ring for bo moves. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 4bb62c95 upstream. Always need to set bit 0 of RLC_CGTT_MGCG_OVERRIDE to avoid unreliable doorbell updates in some cases. Signed-off-by:
-
Alex Deucher authored
commit 129acb7c upstream. Need to disable DS, not enable it when disabling dpm. Signed-off-by:
-
Tetsuo Handa authored
commit 881fdaa5 upstream. Andrew Morton wrote: > On Wed, 12 Nov 2014 13:08:55 +0900 Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> wrote: > > > Andrew Morton wrote: > > > Poor ttm guys - this is a bit of a trap we set for them. > > > > Commit a91576d7 ("drm/ttm: Pass GFP flags in order to avoid deadlock.") > > changed to use sc->gfp_mask rather than GFP_KERNEL. > > > > - pages_to_free = kmalloc(npages_to_free * sizeof(struct page *), > > - GFP_KERNEL); > > + pages_to_free = kmalloc(npages_to_free * sizeof(struct page *), gfp); > > > > But this bug is caused by sc->gfp_mask containing some flags which are not > > in GFP_KERNEL, right? Then, I think > > > > - pages_to_free = kmalloc(npages_to_free * sizeof(struct page *), gfp); > > + pages_to_free = kmalloc(npages_to_free * sizeof(struct page *), gfp & GFP_KERNEL); > > > > would hide this bug. > > > > But I think we should use GFP_ATOMIC (or drop __GFP_WAIT flag) > > Well no - ttm_page_pool_free() should stop calling kmalloc altogether. > Just do > > struct page *pages_to_free[16]; > > and rework the code to free 16 pages at a time. Easy. Well, ttm code wants to process 512 pages at a time for performance. Memory footprint increased by 512 * sizeof(struct page *) buffer is only 4096 bytes. What about using static buffer like below? ---------- >From d3cb5393c9c8099d6b37e769f78c31af1541fe8c Mon Sep 17 00:00:00 2001 From: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Date: Thu, 13 Nov 2014 22:21:54 +0900 Subject: drm/ttm: Avoid memory allocation from shrinker functions. Commit a91576d7 ("drm/ttm: Pass GFP flags in order to avoid deadlock.") caused BUG_ON() due to sc->gfp_mask containing flags which are not in GFP_KERNEL. https://bugzilla.kernel.org/show_bug.cgi?id=87891 Changing from sc->gfp_mask to (sc->gfp_mask & GFP_KERNEL) would avoid the BUG_ON(), but avoiding memory allocation from shrinker function is better and reliable fix. Shrinker function is already serialized by global lock, and clean up function is called after shrinker function is unregistered. Thus, we can use static buffer when called from shrinker function and clean up function. Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Thomas Hellstrom authored
commit 89669e7a upstream. The commit "vmwgfx: Rework fence event action" introduced a number of bugs that are fixed with this commit: a) A forgotten return stateemnt. b) An if statement with identical branches. Reported-by:
Rob Clark <robdclark@gmail.com> Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by:
Jakob Bornecrantz <jakob@vmware.com> Reviewed-by:
Sinclair Yeh <syeh@vmware.com> Signed-off-by:
-
Jay Vosburgh authored
[ Upstream commit 2c26d34b ] When using VXLAN tunnels and a sky2 device, I have experienced checksum failures of the following type: [ 4297.761899] eth0: hw csum failure [...] [ 4297.765223] Call Trace: [ 4297.765224] <IRQ> [<ffffffff8172f026>] dump_stack+0x46/0x58 [ 4297.765235] [<ffffffff8162ba52>] netdev_rx_csum_fault+0x42/0x50 [ 4297.765238] [<ffffffff8161c1a0>] ? skb_push+0x40/0x40 [ 4297.765240] [<ffffffff8162325c>] __skb_checksum_complete+0xbc/0xd0 [ 4297.765243] [<ffffffff8168c602>] tcp_v4_rcv+0x2e2/0x950 [ 4297.765246] [<ffffffff81666ca0>] ? ip_rcv_finish+0x360/0x360 These are reliably reproduced in a network topology of: container:eth0 == host(OVS VXLAN on VLAN) == bond0 == eth0 (sky2) -> switch When VXLAN encapsulated traffic is received from a similarly configured peer, the above warning is generated in the receive processing of the encapsulated packet. Note that the warning is associated with the container eth0. The skbs from sky2 have ip_summed set to CHECKSUM_COMPLETE, and because the packet is an encapsulated Ethernet frame, the checksum generated by the hardware includes the inner protocol and Ethernet headers. The receive code is careful to update the skb->csum, except in __dev_forward_skb, as called by dev_forward_skb. __dev_forward_skb calls eth_type_trans, which in turn calls skb_pull_inline(skb, ETH_HLEN) to skip over the Ethernet header, but does not update skb->csum when doing so. This patch resolves the problem by adding a call to skb_postpull_rcsum to update the skb->csum after the call to eth_type_trans. Signed-off-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Govindarajulu Varadarajan authored
[ Upstream commit 17e96834 ] Hardware always provides compliment of IP pseudo checksum. Stack expects whole packet checksum without pseudo checksum if CHECKSUM_COMPLETE is set. This causes checksum error in nf & ovs. kernel: qg-19546f09-f2: hw csum failure kernel: CPU: 9 PID: 0 Comm: swapper/9 Tainted: GF O-------------- 3.10.0-123.8.1.el7.x86_64 #1 kernel: Hardware name: Cisco Systems Inc UCSB-B200-M3/UCSB-B200-M3, BIOS B200M3.2.2.3.0.080820141339 08/08/2014 kernel: ffff881218f40000 df68243feb35e3a8 ffff881237a43ab8 ffffffff815e237b kernel: ffff881237a43ad0 ffffffff814cd4ca ffff8829ec71eb00 ffff881237a43af0 kernel: ffffffff814c6232 0000000000000286 ffff8829ec71eb00 ffff881237a43b00 kernel: Call Trace: kernel: <IRQ> [<ffffffff815e237b>] dump_stack+0x19/0x1b kernel: [<ffffffff814cd4ca>] netdev_rx_csum_fault+0x3a/0x40 kernel: [<ffffffff814c6232>] __skb_checksum_complete_head+0x62/0x70 kernel: [<ffffffff814c6251>] __skb_checksum_complete+0x11/0x20 kernel: [<ffffffff8155a20c>] nf_ip_checksum+0xcc/0x100 kernel: [<ffffffffa049edc7>] icmp_error+0x1f7/0x35c [nf_conntrack_ipv4] kernel: [<ffffffff814cf419>] ? netif_rx+0xb9/0x1d0 kernel: [<ffffffffa040eb7b>] ? internal_dev_recv+0xdb/0x130 [openvswitch] kernel: [<ffffffffa04c8330>] nf_conntrack_in+0xf0/0xa80 [nf_conntrack] kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40 kernel: [<ffffffffa049e302>] ipv4_conntrack_in+0x22/0x30 [nf_conntrack_ipv4] kernel: [<ffffffff815005ca>] nf_iterate+0xaa/0xc0 kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40 kernel: [<ffffffff81500664>] nf_hook_slow+0x84/0x140 kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40 kernel: [<ffffffff81509dd4>] ip_rcv+0x344/0x380 Hardware verifies IP & tcp/udp header checksum but does not provide payload checksum, use CHECKSUM_UNNECESSARY. Set it only if its valid IP tcp/udp packet. Cc: Jiri Benc <jbenc@redhat.com> Cc: Stefan Assmann <sassmann@redhat.com> Reported-by:
Sunil Choudhary <schoudha@redhat.com> Signed-off-by:
Govindarajulu Varadarajan <_govind@gmx.com> Reviewed-by:
Jiri Benc <jbenc@redhat.com> Signed-off-by:
-
Jiri Pirko authored
[ Upstream commit b0d11b42 ] This patch is fixing a race condition that may cause setting count_pending to -1, which results in unwanted big bulk of arp messages (in case of "notify peers"). Consider following scenario: count_pending == 2 CPU0 CPU1 team_notify_peers_work atomic_dec_and_test (dec count_pending to 1) schedule_delayed_work team_notify_peers atomic_add (adding 1 to count_pending) team_notify_peers_work atomic_dec_and_test (dec count_pending to 1) schedule_delayed_work team_notify_peers_work atomic_dec_and_test (dec count_pending to 0) schedule_delayed_work team_notify_peers_work atomic_dec_and_test (dec count_pending to -1) Fix this race by using atomic_dec_if_positive - that will prevent count_pending running under 0. Fixes: fc423ff0 ("team: add peer notification") Fixes: 492b200e ("team: add support for sending multicast rejoins") Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 7a05dc64 ] Commit d75b1ade ("net: less interrupt masking in NAPI") uncovered wrong alx_poll() behavior. A NAPI poll() handler is supposed to return exactly the budget when/if napi_complete() has not been called. It is also supposed to return number of frames that were received, so that netdev_budget can have a meaning. Also, in case of TX pressure, we still have to dequeue received packets : alx_clean_rx_irq() has to be called even if alx_clean_tx_irq(alx) returns false, otherwise device is half duplex. Signed-off-by:
Eric Dumazet <edumazet@google.com> Fixes: d75b1ade ("net: less interrupt masking in NAPI") Reported-by:
Oded Gabbay <oded.gabbay@amd.com> Bisected-by:
-
Herbert Xu authored
[ Upstream commit 843925f3 ] Thomas Jarosch reported IPsec TCP stalls when a PMTU event occurs. In fact the problem was completely unrelated to IPsec. The bug is also reproducible if you just disable TSO/GSO. The problem is that when the MSS goes down, existing queued packet on the TX queue that have not been transmitted yet all look like TSO packets and get treated as such. This then triggers a bug where tcp_mss_split_point tells us to generate a zero-sized packet on the TX queue. Once that happens we're screwed because the zero-sized packet can never be removed by ACKs. Fixes: 1485348d ("tcp: Apply device TSO segment limit earlier") Reported-by:
Thomas Jarosch <thomas.jarosch@intra2net.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Cheers, Signed-off-by:
-
Thomas Graf authored
[ Upstream commit b8fb4e06 ] skb_scrub_packet() is called when a packet switches between a context such as between underlay and overlay, between namespaces, or between L3 subnets. While we already scrub the packet mark, connection tracking entry, and cached destination, the security mark/context is left intact. It seems wrong to inherit the security context of a packet when going from overlay to underlay or across forwarding paths. Signed-off-by:
Thomas Graf <tgraf@suug.ch> Acked-by:
Flavio Leitner <fbl@sysclose.org> Signed-off-by:
-
Toshiaki Makita authored
[ Upstream commit 796f2da8 ] When vlan tags are stacked, it is very likely that the outer tag is stored in skb->vlan_tci and skb->protocol shows the inner tag's vlan_proto. Currently netif_skb_features() first looks at skb->protocol even if there is the outer tag in vlan_tci, thus it incorrectly retrieves the protocol encapsulated by the inner vlan instead of the inner vlan protocol. This allows GSO packets to be passed to HW and they end up being corrupted. Fixes: 58e998c6 ("offloading: Force software GSO for multiple vlan tags.") Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by:
-
Antonio Quartulli authored
[ Upstream commit 0d164491 ] Gateway having bandwidth_down equal to zero are not accepted at all and so never added to the Gateway list. For this reason checking the bandwidth_down member in batadv_gw_out_of_range() is useless. This is probably a copy/paste error and this check was supposed to be "!gw_node" only. Moreover, the way the check is written now may also lead to a NULL dereference. Fix this by rewriting the if-condition properly. Introduced by 414254e3 ("batman-adv: tvlv - gateway download/upload bandwidth container") Signed-off-by:
Antonio Quartulli <antonio@meshcoding.com> Reported-by:
David Binderman <dcb314@hotmail.com> Signed-off-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
-
Sven Eckelmann authored
[ Upstream commit 0402e444 ] The fragmentation code was replaced in 610bfc6b ("batman-adv: Receive fragmented packets and merge") by an implementation which can handle up to 16 fragments of a packet. The packet is prepared for the split in fragments by the function batadv_frag_send_packet and the actual split is done by batadv_frag_create. Both functions calculate the size of a fragment themself. But their calculation differs because batadv_frag_send_packet also subtracts ETH_HLEN. Therefore, the check in batadv_frag_send_packet "can a full fragment can be created?" may return true even when batadv_frag_create cannot create a full fragment. The function batadv_frag_create doesn't check the size of the skb before splitting it and therefore might try to create a larger fragment than the remaining buffer. This creates an integer underflow and an invalid len is given to skb_split. Signed-off-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
-
Sven Eckelmann authored
[ Upstream commit 5b6698b0 ] The fragmentation code was replaced in 610bfc6b ("batman-adv: Receive fragmented packets and merge"). The new code provided a mostly unused parameter skb for the merging function. It is used inside the function to calculate the additionally needed skb tailroom. But instead of increasing its own tailroom, it is only increasing the tailroom of the first queued skb. This is not correct in some situations because the first queued entry can be a different one than the parameter. An observed problem was: 1. packet with size 104, total_size 1464, fragno 1 was received - packet is queued 2. packet with size 1400, total_size 1464, fragno 0 was received - packet is queued at the end of the list 3. enough data was received and can be given to the merge function (1464 == (1400 - 20) + (104 - 20)) - merge functions gets 1400 byte large packet as skb argument 4. merge function gets first entry in queue (104 byte) - stored as skb_out 5. merge function calculates the required extra tail as total_size - skb->len - pskb_expand_head tail of skb_out with 64 bytes 6. merge function tries to squeeze the extra 1380 bytes from the second queued skb (1400 byte aka skb parameter) in the 64 extra tail bytes of skb_out Instead calculate the extra required tail bytes for skb_out also using skb_out instead of using the parameter skb. The skb parameter is only used to get the total_size from the last received packet. This is also the total_size used to decide that all fragments were received. Reported-by:
Philipp Psurek <philipp.psurek@gmail.com> Signed-off-by:
Martin Hundebøll <martin@hundeboll.net> Signed-off-by:
-
Prashant Sreedharan authored
[ Upstream commit 05b0aa57 ] During driver load in tg3_init_one, if the driver detects DMA activity before intializing the chip tg3_halt is called. As part of tg3_halt interrupts are disabled using routine tg3_disable_ints. This routine was using mailbox value which was not initialized (default value is 0). As a result driver was writing 0x00000001 to pci config space register 0, which is the vendor id / device id. This driver bug was exposed because of the commit a7877b17a667 (PCI: Check only the Vendor ID to identify Configuration Request Retry). Also this issue is only seen in older generation chipsets like 5722 because config space write to offset 0 from driver is possible. The newer generation chips ignore writes to offset 0. Also without commit a7877b17a667, for these older chips when a GRC reset is issued the Bootcode would reprogram the vendor id/device id, which is the reason this bug was masked earlier. Fixed by initializing the interrupt mailbox registers before calling tg3_halt. Please queue for -stable. Reported-by:
Nils Holland <nholland@tisys.org> Reported-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
Prashant Sreedharan <prashant@broadcom.com> Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
-
stephen hemminger authored
[ Upstream commit 6d08acd2 ] Resolve conflicts between glibc definition of IPV6 socket options and those defined in Linux headers. Looks like earlier efforts to solve this did not cover all the definitions. It resolves warnings during iproute2 build. Please consider for stable as well. Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Thomas Graf authored
[ Upstream commit a18e6a18 ] Each mmap Netlink frame contains a status field which indicates whether the frame is unused, reserved, contains data or needs to be skipped. Both loads and stores may not be reordeded and must complete before the status field is changed and another CPU might pick up the frame for use. Use an smp_mb() to cover needs of both types of callers to netlink_set_status(), callers which have been reading data frame from the frame, and callers which have been filling or releasing and thus writing to the frame. - Example code path requiring a smp_rmb(): memcpy(skb->data, (void *)hdr + NL_MMAP_HDRLEN, hdr->nm_len); netlink_set_status(hdr, NL_MMAP_STATUS_UNUSED); - Example code path requiring a smp_wmb(): hdr->nm_uid = from_kuid(sk_user_ns(sk), NETLINK_CB(skb).creds.uid); hdr->nm_gid = from_kgid(sk_user_ns(sk), NETLINK_CB(skb).creds.gid); netlink_frame_flush_dcache(hdr); netlink_set_status(hdr, NL_MMAP_STATUS_VALID); Fixes: f9c228 ("netlink: implement memory mapped recvmsg()") Reported-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
David Miller authored
[ Upstream commit 4682a035 ] Checking the file f_count and the nlk->mapped count is not completely sufficient to prevent the mmap'd area contents from changing from under us during netlink mmap sendmsg() operations. Be careful to sample the header's length field only once, because this could change from under us as well. Fixes: 5fd96123 ("netlink: implement memory mapped sendmsg()") Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Acked-by:
-
Timo Teräs authored
[ Upstream commit 8a0033a9 ] The NBMA GRE tunnels temporarily push GRE header that contain the per-packet NBMA destination on the skb via header ops early in xmit path. It is the later pulled before the real GRE header is constructed. The inner mac was thus set differently in nbma case: the GRE header has been pushed by neighbor layer, and mac header points to beginning of the temporary gre header (set by dev_queue_xmit). Now that the offloads expect mac header to point to the gre payload, fix the xmit patch to: - pull first the temporary gre header away - and reset mac header to point to gre payload This fixes tso to work again with nbma tunnels. Fixes: 14051f04 ("gre: Use inner mac length when computing tunnel length") Signed-off-by:
Timo Teräs <timo.teras@iki.fi> Cc: Tom Herbert <therbert@google.com> Cc: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by:
-
- 16 Jan, 2015 2 commits
-
-
Greg Kroah-Hartman authored
-
Linus Torvalds authored
commit 690eac53 upstream. Commit fee7e49d ("mm: propagate error from stack expansion even for guard page") made sure that we return the error properly for stack growth conditions. It also theorized that counting the guard page towards the stack limit might break something, but also said "Let's see if anybody notices". Somebody did notice. Apparently android-x86 sets the stack limit very close to the limit indeed, and including the guard page in the rlimit check causes the android 'zygote' process problems. So this adds the (fairly trivial) code to make the stack rlimit check be against the actual real stack size, rather than the size of the vma that includes the guard page. Reported-and-tested-by:
Chih-Wei Huang <cwhuang@android-x86.org> Cc: Jay Foad <jay.foad@gmail.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
