- 20 May, 2021 13 commits
-
-
Guangbin Huang authored
Currently, user gets qset shaper parameters by implementing debugfs command "echo dump qs shaper > cmd", this command will dump info in dmesg. It's unnecessary and heavy. As there is "tm_qset" file in tm directory for dump qset info, to optimize these command, merge qset shaper parameters to tm_qset file and use cat command to get them. The display style is below: $ cat tm_qset ID MAP_PRI LINK_VLD MODE DWRR IR_B IR_U IR_S BS_B BS_S FLAG 0000 0 1 dwrr 100 150 7 0 5 20 0 0001 0 0 sp 0 150 7 0 5 20 0 Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Guangbin Huang authored
Currently, user gets qos buffer config by implementing debugfs command "echo dump qos buf cfg > cmd", this command will dump info in dmesg. It's unnecessary and heavy. To optimize it, create a single file "qos_buf_cfg" in tm directory and use cat command to get info. It will return info to userspace, rather than record in dmesg. The display style is below: $ cat qos_buf_cfg tx_packet_buf_tc_0: 0x120 tx_packet_buf_tc_1: 0x120 tx_packet_buf_tc_2: 0x120 tx_packet_buf_tc_3: 0x120 tx_packet_buf_tc_4: 0x0 tx_packet_buf_tc_5: 0x0 tx_packet_buf_tc_6: 0x0 tx_packet_buf_tc_7: 0x0 ...... Signed-off-by:
-
Guangbin Huang authored
Currently, user gets priority map by implementing debugfs command "echo dump qos pri map > cmd", this command will dump info in dmesg. It's unnecessary and heavy. To optimize it, create a single file "qos_pri_map" in tm directory and use cat command to get info. It will return info to userspace, rather than record in dmesg. The display style is below: $ cat qos_pri_map vlan_to_pri: 0 PRI TC 0 0 1 1 2 2 3 3 4 0 5 1 6 2 Signed-off-by:
-
Guangbin Huang authored
Currently, user gets pause config by implementing debugfs command "echo dump qos pause cfg > cmd", this command will dump info in dmesg. It's unnecessary and heavy. To optimize it, create a single file "qos_pause_cfg" in tm directory and use cat command to get info. It will return info to userspace, rather than record in dmesg. The display style is below: $ cat qos_pause_cfg pause_trans_gap: 0x7f pause_trans_time: 0xffff Signed-off-by:
-
Guangbin Huang authored
Currently, user gets tc schedule info by implementing debugfs command "echo dump tc > cmd", this command will dump info in dmesg. It's unnecessary and heavy. To optimize it, create a single file "tc_sch_info" and use cat command to get info. It will return info to userspace, rather than record in dmesg. The display style is below: $ cat tc_sch_info enabled tc number: 4 weight_offset: 14 TC MODE WEIGHT 0 dwrr 25 1 dwrr 25 2 dwrr 25 3 dwrr 25 4 dwrr 0 5 dwrr 0 6 dwrr 0 7 dwrr 0 Signed-off-by:
-
Guangbin Huang authored
Currently, user gets some tm info by implementing debugfs command "echo dump tm > cmd", this command will dump info in dmesg. It's unnecessary and heavy. In addition, the info of this command mixes info of qset, priority, pg and port. Qset and priority have their own command to get info of themself, so can remove info of qset and priority from this command. To optimize it, create two new files "tm_pg", "tm_port" in tm directory and use cat command to separately get info of pg and port. The display style is below: $ cat tm_pg ID PRI_MAP MODE DWRR C_IR_B C_IR_U C_IR_S C_BS_B C_BS_S ... 00 0x1f dwrr 1 75 9 0 31 20 ... $ cat tm_port IR_B IR_U IR_S BS_B BS_S FLAG RATE(Mbps) 75 9 0 31 20 1 200000 Signed-off-by:
-
Guangbin Huang authored
Currently, the debugfs command for tm map is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create a single file "tm_map" for it, and query it by command "cat tm_map", return the result to userspace, rather than record in dmesg. As user can't specify queue id in cat command, driver will return info of all queue id. The display style is below: $ cat tm_map queue_id qset_id pri_id tc_id 0000 0000 00 00 INDEX | TM BP QSET MAPPING: 0000 | 00000000:00000000:00000000:00000000:00000000:00000000:00000000 0256 | 00000000:00000000:00000000:00000000:00000000:00000002:00000000 0512 | 00000000:00000000:00000000:00000004:00000000:00000000:00000000 0768 | 00000000:00000008:00000000:00000000:00000000:00000000:00000000 Signed-off-by:
-
Hao Chen authored
Currently, the debugfs command for fd tcam is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create a single file "fd_tcam" for it, and query it by command "cat fd_tcam", return the result to userspace, rather than record in dmesg. The display style is below: $ cat fd_tcam read result tcam key x(31): 00000000 00000000 00000000 08000000 00000600 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 read result tcam key y(31): 00000000 00000000 00000000 f7ff0000 0000f900 00000000 00000000 00000000 00000000 00000000 00000000 00000000 0000fff8 Signed-off-by:
Hao Chen <chenhao288@hisilicon.com> Signed-off-by:
-
Hao Chen authored
Currently, the debugfs command for queue info is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create two files "rx_queue_info" and "tx_queue_info" for it, and query it by command "cat rx_queue_info" and "cat tx_queue_info", return the result to userspace, rather than record in dmesg. The display style is below: $ cat rx_queue_info QUEUE_ID BD_NUM BD_LEN TAIL HEAD FBDNUM PKTNUM ... 0 0 0 0 0 0 0 ... 1 0 0 0 0 0 0 ... 2 0 0 0 0 0 0 ... $ cat tx_queue_info QUEUE_ID BD_NUM TC TAIL HEAD FBDNUM OFFSET PKTNUM ... 0 0 0 0 0 0 0 0 ... 1 0 0 0 0 0 0 0 ... 2 0 0 0 0 0 0 0 ... Signed-off-by:
-
Hao Chen authored
Currently, the debugfs command for queue map is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create a single file "queue_map" for it, and query it by command "cat queue_map", return the result to userspace, rather than record in dmesg. The display style is below: $ cat queue_map local_queue_id global_queue_id vector_id 0 0 341 Signed-off-by:
-
Yufeng Mo authored
Currently, the debugfs command for reg dcb info is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create a single file "dcb" for it, and query it by command "cat dcb", return the result to userspace, rather than record in dmesg. The display style is below: $ cat dcb qset_id roce_qset_mask nic_qset_mask qset_shaping_pass qset_bp_status 0000 0x1 0x1 0x1 0x0 0001 0x1 0x1 0x1 0x0 0002 0x1 0x1 0x1 0x0 0003 0x1 0x1 0x1 0x0 0004 0x1 0x1 0x1 0x0 0005 0x1 0x1 0x1 0x0 0006 0x1 0x1 0x1 0x0 0007 0x1 0x1 0x1 0x0 pri_id pri_mask pri_cshaping_pass pri_pshaping_pass 000 0x1 0x0 0x1 001 0x1 0x0 0x0 002 0x1 0x0 0x0 003 0x1 0x0 0x0 004 0x1 0x0 0x0 005 0x1 0x0 0x0 006 0x1 0x0 0x0 007 0x1 0x0 0x0 pg_id pg_mask pg_cshaping_pass pg_pshaping_pass 000 0x1 0x0 0x1 Signed-off-by:
Yufeng Mo <moyufeng@huawei.com> Signed-off-by:
-
Yufeng Mo authored
Currently, the debugfs command for reg is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create some files "bios_common/ssu/igu_egu/rpu/ncsi/rtc/ppp/rcb/tqp/mac" for it, and query it by command "cat xxx", return the result to userspace, rather than record in dmesg. The display style is below: $ cat bios_common BP_CPU_STATE: 0x0 DFX_MSIX_INFO_NIC_0: 0xc000 DFX_MSIX_INFO_NIC_1: 0x0 DFX_MSIX_INFO_NIC_2: 0x0 DFX_MSIX_INFO_NIC_3: 0x0 DFX_MSIX_INFO_ROC_0: 0xc000 DFX_MSIX_INFO_ROC_1: 0x0 DFX_MSIX_INFO_ROC_2: 0x0 DFX_MSIX_INFO_ROC_3: 0x0 Signed-off-by:
-
Zhen Lei authored
As Leon Romanovsky's tips: The definition of macro PIPELINE_DEBUG is commented more than 10 years ago and can be seen as a dead code that should be removed. Suggested-by:
Leon Romanovsky <leon@kernel.org> Signed-off-by:
Zhen Lei <thunder.leizhen@huawei.com> Reviewed-by:
Leon Romanovsky <leonro@nvidia.com> Signed-off-by:
-
- 19 May, 2021 27 commits
-
-
David S. Miller authored
DENG Qingfang says: ==================== MT7530 interrupt support Add support for MT7530 interrupt controller. ==================== Signed-off-by: -
DENG Qingfang authored
Enable MT7530 interrupt controller in the MT7621 SoC. Signed-off-by:
DENG Qingfang <dqfext@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Vladimir Oltean <olteanv@gmail.com> Signed-off-by:
-
DENG Qingfang authored
Add device tree binding to support MT7530 interrupt controller. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
DENG Qingfang authored
Add support for MT7530 interrupt controller to handle internal PHYs. In order to assign an IRQ number to each PHY, the registration of MDIO bus is also done in this driver. Signed-off-by:
-
DENG Qingfang authored
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530 and MT7531 switches. The initialization procedure is from the vendor driver, but due to lack of documentation, the function of some register values remains unknown. Signed-off-by:
-
Wei Yongjun authored
Fix to return a negative error code -ENOMEM from the error handling case instead of 0, as done elsewhere in this function. Fixes: c6e08d62 ("net: qrtr: Allocate workqueue before kernel_bind") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by:
-
Wei Yongjun authored
In case of error, the function mdiobus_get_phy() returns NULL pointer not ERR_PTR(). The IS_ERR() test in the return value check should be replaced with NULL test. Reported-by:
-
Davide Caratti authored
modern userspace applications, like OVN, can configure the TC datapath to "recirculate" packets several times. If more than 4 "recirculation" rules are configured, packets can be dropped by __tcf_classify(). Changing the maximum number of reclassifications (from 4 to 16) should be sufficient to prevent drops in most use cases, and guard against loops at the same time. Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextDavid S. Miller authored
Alexei Starovoitov says: ==================== pull-request: bpf-next 2021-05-19 The following pull-request contains BPF updates for your *net-next* tree. We've added 43 non-merge commits during the last 11 day(s) which contain a total of 74 files changed, 3717 insertions(+), 578 deletions(-). The main changes are: 1) syscall program type, fd array, and light skeleton, from Alexei. 2) Stop emitting static variables in skeleton, from Andrii. 3) Low level tc-bpf api, from Kumar. 4) Reduce verifier kmalloc/kfree churn, from Lorenz. ====================
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: Add support for new multipath hash policies This patchset adds support for two new multipath hash policies in mlxsw. Patch #1 emits net events whenever the net.ipv{4,6}.fib_multipath_hash_fields sysctls are changed. This allows listeners to react to changes in the packet fields used for the computation of the multipath hash. Patches #2-#3 refactor the code in mlxsw that is responsible for the configuration of the multipath hash, so that it will be easier to extend for the two new policies. Patch #4 adds the register fields required to support the new policies. Patch #5-#7 add support for inner layer 3 and custom multipath hash policies. Tested using following forwarding selftests: * custom_multipath_hash.sh * gre_custom_multipath_hash.sh * gre_inner_v4_multipath.sh * gre_inner_v6_multipath.sh ==================== -
Ido Schimmel authored
When this policy is set, only enable the packet fields that were enabled by user space for multipath hash computation. Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Reviewed-by:
Petr Machata <petrm@nvidia.com> Signed-off-by:
-
Ido Schimmel authored
When this policy is set, the kernel uses the inner layer 3 fields for multipath hash computation and falls back to the outer fields if no encapsulation was encountered. This behavior is most likely influenced by the behavior of the flow dissector, which is used for the packet dissection. The Spectrum ASIC, however, cannot fallback to outer fields if inner fields are not available. This should not result in a discrepancy from the software data path because if several flows have matching inner fields, they will tend to have matching outer fields as well. Therefore, implement this policy by enabling both outer and inner layer 3 fields for the multipath hash computation. Signed-off-by:
-
Ido Schimmel authored
Outer IPv4 and IPv6 addresses are used by multiple multipath hash policies. Factor out helpers that set these fields to increase code sharing between different policies. Signed-off-by:
-
Ido Schimmel authored
The RECRv2 register is used for setting up the router's ECMP hash configuration. Extend it with inner packet fields to allow the ECMP hash to be calculated based on inner flow information. Signed-off-by:
-
Ido Schimmel authored
Currently, the multipath hash configuration is written directly to the register payload. While this is OK for the two currently supported policies, it is going to be hard to follow when more policies and more packet fields are added. Instead, set the required headers and fields in a bitmap and then dump it to the register payload. Signed-off-by:
-
Ido Schimmel authored
The code was written when only two multipath hash policies were present, so the if statement was sufficient. The next patch and future patches are going to add support for more policies, so move to a switch statement. Signed-off-by:
-
Ido Schimmel authored
In-kernel notifications are already sent when the multipath hash policy itself changes, but not when the multipath hash fields change. Add these notifications, so that interested listeners (e.g., switch ASIC drivers) could perform the necessary configuration. Signed-off-by:
-
Stephan Gerhold authored
S3FWRN5 depends on a clock input ("XI" pin) to function properly. Depending on the hardware configuration this could be an always-on oscillator or some external clock that must be explicitly enabled. So far we assumed that the clock is always-on. Make the driver request an (optional) clock from the device tree and make sure the clock is running before starting S3FWRN5. Note: S3FWRN5 asserts "GPIO2" whenever it needs the clock input to function correctly. On some hardware configurations, GPIO2 is connected directly to an input pin of the external clock provider (e.g. the main PMIC of the SoC). In that case, it can automatically AND the clock enable bit and clock request from S3FWRN5 so that the clock is actually only enabled when needed. It is also conceivable that on some other hardware configuration S3FWRN5's GPIO2 might be connected as a regular GPIO input of the SoC. In that case, follow-up patches could extend the driver to request the GPIO, set up an interrupt and only enable the clock when requested by S3FWRN5. Signed-off-by:Stephan Gerhold <stephan@gerhold.net> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by:
-
Stephan Gerhold authored
On some systems, S3FWRN5 depends on having an external clock enabled to function correctly. Allow declaring that clock in the device tree. Signed-off-by:
-
Zheng Yejian authored
loginuid/sessionid/secid have been read from 'current' instead of struct netlink_skb_parms, the parameter 'skb' seems no longer needed. Fixes: c53fa1ed ("netlink: kill loginuid/sessionid/sid members from struct netlink_skb_parms") Signed-off-by:
Zheng Yejian <zhengyejian1@huawei.com> Signed-off-by:
-
David S. Miller authored
Guangbin Huang says: ==================== net: intel: some cleanups This patchset adds some cleanups for intel e1000/e1000e ethernet driver. ==================== Reviewed-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by:
-
Hao Chen authored
There is a misspell word "retreived" in comment, so fix it to "retrieved". Signed-off-by:
-
Hao Chen authored
There are double "slot" in comment, so remove the redundant one. Signed-off-by:
-
Hao Chen authored
There are double "the" in comment, so remove the redundant one. Signed-off-by:
-
Hao Chen authored
There are double "in" and "to" in comments, so remove the redundant one. Signed-off-by:
-
Hao Chen authored
There are double "slot" in comment, so remove the redundant one. Signed-off-by:
-
David S. Miller authored
Hui Tang says: ==================== net: ethernet: remove leading spaces before tabs There are a few leading spaces before tabs and remove it by running the following commard: $ find . -name '*.c' | xargs sed -r -i 's/^[ ]+\t/\t/' $ find . -name '*.h' | xargs sed -r -i 's/^[ ]+\t/\t/' ==================== Signed-off-by:
-
