- 14 Mar, 2019 40 commits
-
-
Anson Huang authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 0efcc2c0 ] Same as other i.MX6 SoCs, ensure unused MMDC channel's handshake is bypassed, this is to make sure no request signal will be generated when periphe_clk_sel is changed or SRC warm reset is triggered. Signed-off-by:
Anson Huang <Anson.Huang@nxp.com> Signed-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org> Signed-off-by:
Juerg Haefliger <juergh@canonical.com> Signed-off-by:
Khalid Elmously <khalid.elmously@canonical.com>
-
Sergei Shtylyov authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 9f83cfdb ] The driver overrides the error codes returned by platform_get_irq() to -EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe permanently instead of the deferred probing. Switch to propagating the error code upstream, still checking/overriding IRQ0 as libata regards it as "no IRQ" (thus polling) anyway... Fixes: 9ec36caf ("of/irq: do irq resolution in platform_get_irq") Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Will Deacon authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit a868e853 ] After removing an entry from a queue (e.g. reading an event in arm_smmu_evtq_thread()) it is necessary to advance the MMIO consumer pointer to free the queue slot back to the SMMU. A memory barrier is required here so that all reads targetting the queue entry have completed before the consumer pointer is updated. The implementation of queue_inc_cons() relies on a writel() to complete the previous reads, but this is incorrect because writel() is only guaranteed to complete prior writes. This patch replaces the call to writel() with an mb(); writel_relaxed() sequence, which gives us the read->write ordering which we require. Cc: Robin Murphy <robin.murphy@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Jiong Wang authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 17f6c83f ] For micro-mips, srlv inside POOL32A encoding space should use 0x50 sub-opcode, NOT 0x90. Some early version ISA doc describes the encoding as 0x90 for both srlv and srav, this looks to me was a typo. I checked Binutils libopcode implementation which is using 0x50 for srlv and 0x90 for srav. v1->v2: - Keep mm_srlv32_op sorted by value. Fixes: f31318fd ("MIPS: uasm: Add srlv uasm instruction") Cc: Markos Chandras <markos.chandras@imgtec.com> Cc: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Acked-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by:
Song Liu <songliubraving@fb.com> Signed-off-by:
Jiong Wang <jiong.wang@netronome.com> Signed-off-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Russell King - ARM Linux authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 84fb6c7f ] It was noticed that unbinding and rebinding the KSZ8851 ethernet resulted in the driver reporting "failed to read device ID" at probe. Probing the reset line with a 'scope while repeatedly attempting to bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is constantly held at zero, meaning the device is held in reset, and does not respond on the SPI bus. Experimentation with the startup delay on the regulator set to 50ms shows that the reset is positively released after 20ms. Schematics for this board are not available, and the traces are buried in the inner layers of the board which makes tracing where the RSTN pin extremely difficult. We can only guess that the RSTN pin is wired to a reset generator chip driven off the ethernet supply, which fits the observed behaviour. Include this delay in the regulator startup delay - effectively treating the reset as a "supply stable" indicator. This can not be modelled as a delay in the KSZ8851 driver since the reset generation is board specific - if the RSTN pin had been wired to a GPIO, reset could be released earlier via the already provided support in the KSZ8851 driver. This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based on Blaze schematics that should be very close to SDP4430: TPS22902YFPR is used as the regulator switch (gpio48 controlled): Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV. (SCH Note: Threshold set at 90%. Vsense: 0.405V). According to the TPS3808 data sheet the RESET delay time when Ct is open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> [tony@atomide.com: updated with notes from schematics from Peter] Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Bart Van Assche authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit ce10a5b3 ] tk_core.seq is initialized open coded, but that misses to initialize the lockdep map when lockdep is enabled. Lockdep splats involving tk_core seq consequently lack a name and are hard to read. Use the proper initializer which takes care of the lockdep map initialization. [ tglx: Massaged changelog ] Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: peterz@infradead.org Cc: tj@kernel.org Cc: johannes.berg@intel.com Link: https://lkml.kernel.org/r/20181128234325.110011-12-bvanassche@acm.orgSigned-off-by:
-
Mathias Nyman authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit e8610894 ] When initializing a hub we want to give a USB3 port in link training the same debounce delay time before autosuspening the hub as already trained, connected enabled ports. USB3 ports won't reach the enabled state with "current connect status" and "connect status change" bits set until the USB3 link training finishes. Catching the port in link training (polling) and adding the debounce delay prevents unnecessary failed attempts to autosuspend the hub. Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Zoran Markovic authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 5b841bfa ] Function smack_key_permission() only issues smack requests for the following operations: - KEY_NEED_READ (issues MAY_READ) - KEY_NEED_WRITE (issues MAY_WRITE) - KEY_NEED_LINK (issues MAY_WRITE) - KEY_NEED_SETATTR (issues MAY_WRITE) A blank smack request is issued in all other cases, resulting in smack access being granted if there is any rule defined between subject and object, or denied with -EACCES otherwise. Request MAY_READ access for KEY_NEED_SEARCH and KEY_NEED_VIEW. Fix the logic in the unlikely case when both MAY_READ and MAY_WRITE are needed. Validate access permission field for valid contents. Signed-off-by:
Zoran Markovic <zmarkovic@sierrawireless.com> Signed-off-by:
Casey Schaufler <casey@schaufler-ca.com> Cc: Casey Schaufler <casey@schaufler-ca.com> Cc: James Morris <jmorris@namei.org> Cc: "Serge E. Hallyn" <serge@hallyn.com> Signed-off-by:
-
Alexey Khoroshilov authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit aa35dc3c ] If vpbe_set_default_output() or vpbe_set_default_mode() fails, vpbe_initialize() returns error code without releasing resources. The patch adds error handling for that case. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
Sebastian Andrzej Siewior authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 6637401c ] Every user of user_insn() passes an user memory pointer to this macro. Add might_fault() to user_insn() so we can spot users which are using this macro in sections where page faulting is not allowed. [ bp: Space it out to make it more visible. ] Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Borislav Petkov <bp@suse.de> Reviewed-by:
Rik van Riel <riel@surriel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: "Jason A. Donenfeld" <Jason@zx2c4.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kvm ML <kvm@vger.kernel.org> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20181128222035.2996-6-bigeasy@linutronix.deSigned-off-by:
-
Lubomir Rintel authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 1147e05a ] Marvell keeps their MMP2 datasheet secret, but there are good clues that TWSI2 is not on 0xd4025000 on that platform, not does it use IRQ 58. In fact, the IRQ 58 on MMP2 seems to be a signal processor: arch/arm/mach-mmp/irqs.h:#define IRQ_MMP2_MSP 58 I'm taking a somewhat educated guess that is probably a copy & paste error from PXA168 or PXA910 and that the real controller in fact hides at address 0xd4031000 and uses an interrupt line multiplexed via IRQ 17. I'm also copying some properties from TWSI1 that were missing or incorrect. Tested on a OLPC XO 1.75 machine, where the RTC is on TWSI2. Signed-off-by:
Lubomir Rintel <lkundrak@v3.sk> Tested-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Mark Rutland authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 6e803e2e ] The core ftrace code requires that when it is handed the PC of an instrumented function, this PC is the address of the instrumented instruction. This is necessary so that the core ftrace code can identify the specific instrumentation site. Since the instrumented function will be a BL, the address of the instrumented function is LR - 4 at entry to the ftrace code. This fixup is applied in the mcount_get_pc and mcount_get_pc0 helpers, which acquire the PC of the instrumented function. The mcount_get_lr helper is used to acquire the LR of the instrumented function, whose value does not require this adjustment, and cannot be adjusted to anything meaningful. No adjustment of this value is made on other architectures, including arm. However, arm64 adjusts this value by 4. This patch brings arm64 in line with other architectures and removes the adjustment of the LR value. Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Torsten Duwe <duwe@suse.de> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by:
-
J. Bruce Fields authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 62a063b8 ] Anatoly Trosinenko reports that this: 1) Checkout fresh master Linux branch (tested with commit e195ca6c) 2) Copy x84_64-config-4.14 to .config, then enable NFS server v4 and build 3) From `kvm-xfstests shell`: results in NULL dereference in locks_end_grace. Check that nfsd has been started before trying to end the grace period. Reported-by:
Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Young Xiao authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit a11f6ca9 ] __vdc_tx_trigger should only loop on EAGAIN a finite number of times. See commit adddc32d ("sunvnet: Do not spin in an infinite loop when vio_ldc_send() returns EAGAIN") for detail. Signed-off-by:
Young Xiao <YangX92@hotmail.com> Signed-off-by:
-
Tiezhu Yang authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit f6176473 ] When call f2fs_acl_create_masq() failed, the caller f2fs_acl_create() should return -EIO instead of -ENOMEM, this patch makes it consistent with posix_acl_create() which has been fixed in commit beaf226b ("posix_acl: don't ignore return value of posix_acl_create_masq()"). Fixes: 83dfe53c ("f2fs: fix reference leaks in f2fs_acl_create") Signed-off-by:
Tiezhu Yang <kernelpatch@126.com> Reviewed-by:
Chao Yu <yuchao0@huawei.com> Signed-off-by:
Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by:
-
Yunlei He authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit b61ac5b7 ] This patch move dir data flush to write checkpoint process, by doing this, it may reduce some time for dir fsync. pre: -f2fs_do_sync_file enter -file_write_and_wait_range <- flush & wait -write_checkpoint -do_checkpoint <- wait all -f2fs_do_sync_file exit now: -f2fs_do_sync_file enter -write_checkpoint -block_operations <- flush dir & no wait -do_checkpoint <- wait all -f2fs_do_sync_file exit Signed-off-by:
Yunlei He <heyunlei@huawei.com> Signed-off-by:
-
Yangtao Li authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 9eb40fa2 ] of_find_node_by_path() acquires a reference to the node returned by it and that reference needs to be dropped by its caller. soc_is_tegra() doesn't do that, so fix it. Signed-off-by:
Yangtao Li <tiny.windzz@gmail.com> Acked-by:
Jon Hunter <jonathanh@nvidia.com> [treding: slightly rewrite to avoid inline comparison] Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Pu Wen authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 4787eff3 ] The tool perf is useful for the performance analysis on the Hygon Dhyana platform. But right now there is no Hygon support for it to analyze the KVM guest os data. So add Hygon Dhyana support to it by checking vendor string to share the code path of AMD. Signed-off-by:
Pu Wen <puwen@hygon.cn> Acked-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Sami Tolvanen authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 5818c683 ] If an ARM mapping symbol shares an address with a valid symbol, find_elf_symbol can currently return the mapping symbol instead, as the symbol is not validated. This can result in confusing warnings: WARNING: vmlinux.o(.text+0x18f4028): Section mismatch in reference from the function set_reset_devices() to the variable .init.text:$x.0 This change adds a call to is_valid_name to find_elf_symbol, similarly to how it's already used in find_elf_symbol2. Signed-off-by:
Sami Tolvanen <samitolvanen@google.com> Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
Nathan Chancellor authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit c10b26ab ] When building the kernel with Clang, the following section mismatch warnings appears: WARNING: vmlinux.o(.text+0x2d398): Section mismatch in reference from the function _setup() to the function .init.text:_setup_iclk_autoidle() The function _setup() references the function __init _setup_iclk_autoidle(). This is often because _setup lacks a __init annotation or the annotation of _setup_iclk_autoidle is wrong. WARNING: vmlinux.o(.text+0x2d3a0): Section mismatch in reference from the function _setup() to the function .init.text:_setup_reset() The function _setup() references the function __init _setup_reset(). This is often because _setup lacks a __init annotation or the annotation of _setup_reset is wrong. WARNING: vmlinux.o(.text+0x2d408): Section mismatch in reference from the function _setup() to the function .init.text:_setup_postsetup() The function _setup() references the function __init _setup_postsetup(). This is often because _setup lacks a __init annotation or the annotation of _setup_postsetup is wrong. _setup is used in omap_hwmod_allocate_module, which isn't marked __init and looks like it shouldn't be, meaning to fix these warnings, those functions must be moved out of the init section, which this patch does. Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
-
Renato Lui Geh authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 336650c7 ] The ad7780 driver previously did not read the correct device output, as it read an outdated value set at initialization. It now updates its voltage on read. Signed-off-by:
Renato Lui Geh <renatogeh@gmail.com> Acked-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Matheus Tavares authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit b3a3eafe ] Previously, ad2s90_probe ignored the return code from spi_setup, not handling its possible failure. This patch makes ad2s90_probe check if the code is an error code and, if so, do the following: - Call dev_err with an appropriate error message. - Return the spi_setup's error code. Note: The 'return ret' statement could be out of the 'if' block, but this whole block will be moved up in the function in the patch: 'staging:iio:ad2s90: Move device registration to the end of probe'. Signed-off-by:
Matheus Tavares <matheus.bernardino@usp.br> Signed-off-by:
-
Miroslav Lichvar authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 83d0bdc7 ] If a gettime64 call fails, return the error and avoid copying data back to user. Cc: Richard Cochran <richardcochran@gmail.com> Cc: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by:
Miroslav Lichvar <mlichvar@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Andy Duan authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 397bd921 ] Current driver only enable parity enable bit and never clear it when user set the termios. The fix clear the parity enable bit when PARENB flag is not set in termios->c_cflag. Cc: Lukas Wunner <lukas@wunner.de> Signed-off-by:
Andy Duan <fugang.duan@nxp.com> Reviewed-by:
Fabio Estevam <festevam@gmail.com> Acked-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Frank Rowand authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 5b3f5c40 ] The previous commit, "of: overlay: add missing of_node_get() in __of_attach_node_sysfs" added a missing of_node_get() to __of_attach_node_sysfs(). This results in a refcount imbalance for nodes attached with dlpar_attach_node(). The calling sequence from dlpar_attach_node() to __of_attach_node_sysfs() is: dlpar_attach_node() of_attach_node() __of_attach_node_sysfs() For more detailed description of the node refcount, see commit 68baf692 ("powerpc/pseries: Fix of_node_put() underflow during DLPAR remove"). Tested-by:
Alan Tull <atull@kernel.org> Acked-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Frank Rowand <frank.rowand@sony.com> Signed-off-by:
-
Colin Ian King authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 53bb565f ] In the expression "word1 << 16", word1 starts as u16, but is promoted to a signed int, then sign-extended to resource_size_t, which is probably not what was intended. Cast to resource_size_t to avoid the sign extension. This fixes an identical issue as fixed by commit 0b2d7076 ("x86/PCI: Fix Broadcom CNB20LE unintended sign extension") back in 2014. Detected by CoverityScan, CID#138749, 138750 ("Unintended sign extension") Fixes: 3f6ea84a ("PCI: read memory ranges out of Broadcom CNB20LE host bridge") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Bjorn Helgaas <helgaas@kernel.org> Signed-off-by:
-
Bob Peterson authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 216f0efd ] Before this patch, recovery would cause all callbacks to be delayed, put on a queue, and afterward they were all queued to the callback work queue. This patch does the same thing, but occasionally takes a break after 25 of them so it won't swamp the CPU at the expense of other RT processes like corosync. Signed-off-by:
Bob Peterson <rpeterso@redhat.com> Signed-off-by:
David Teigland <teigland@redhat.com> Signed-off-by:
-
Yufen Wang authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 82c08c3e ] In case panic() and panic() called at the same time on different CPUS. For example: CPU 0: panic() __crash_kexec machine_crash_shutdown crash_smp_send_stop machine_kexec BUG_ON(num_online_cpus() > 1); CPU 1: panic() local_irq_disable panic_smp_self_stop If CPU 1 calls panic_smp_self_stop() before crash_smp_send_stop(), kdump fails. CPU1 can't receive the ipi irq, CPU1 will be always online. To fix this problem, this patch split out the panic_smp_self_stop() and add set_cpu_online(smp_processor_id(), false). Signed-off-by:
Yufen Wang <wangyufen@huawei.com> Signed-off-by:
-
James Smart authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit b114d900 ] When LCB's are rejected, if beaconing was already in progress, the Reason Code Explanation was not being set. Should have been set to command in progress. Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Arnd Bergmann authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 1539c7f2 ] Randconfig testing revealed a very old bug, with gcc-8: sound/soc/intel/atom/sst/sst_loader.c: In function 'sst_load_fw': sound/soc/intel/atom/sst/sst_loader.c:357:5: error: 'fw' may be used uninitialized in this function [-Werror=maybe-uninitialized] if (fw == NULL) { ^ sound/soc/intel/atom/sst/sst_loader.c:354:25: note: 'fw' was declared here const struct firmware *fw; We must check the return code of request_firmware() before we look at the pointer result that may be uninitialized when the function fails. Fixes: 9012c954 ("ASoC: Intel: mrfld - Add DSP load and management") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Slawomir Stepien authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 0559ef7f ] Inside __ad7280_read32(), the spi_sync_transfer() can fail with negative error code. This change will ensure that this error is being passed up in the call stack, so it can be handled. Signed-off-by:
Slawomir Stepien <sst@poczta.fm> Signed-off-by:
-
Gustavo A. R. Silva authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit a3780509 ] idx can be indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: drivers/gpu/drm/drm_bufs.c:1420 drm_legacy_freebufs() warn: potential spectre issue 'dma->buflist' [r] (local cap) Fix this by sanitizing idx before using it to index dma->buflist Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20181016095549.GA23586@embeddedor.comSigned-off-by:
-
Greg Kroah-Hartman authored
BugLink: https://bugs.launchpad.net/bugs/1818806Signed-off-by:
-
Paul E. McKenney authored
BugLink: https://bugs.launchpad.net/bugs/1818806 commit ec3833ed upstream. The cpu_online() function can return values other than 0 and 1, which can result in subscript overflow when applied to a two-element array. This commit allows for this behavior by using "!!" on the return value from cpu_online() when used as a subscript. Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: "Rantala, Tommi" <tommi.t.rantala@nokia.com> Signed-off-by:
-
Michal Kubecek authored
BugLink: https://bugs.launchpad.net/bugs/1818806 commit ade44640 upstream. Since commit 7969e5c4 ("ip: discard IPv4 datagrams with overlapping segments.") IPv4 reassembly code drops the whole queue whenever an overlapping fragment is received. However, the test is written in a way which detects duplicate fragments as overlapping so that in environments with many duplicate packets, fragmented packets may be undeliverable. Add an extra test and for (potentially) duplicate fragment, only drop the new fragment rather than the whole queue. Only starting offset and length are checked, not the contents of the fragments as that would be too expensive. For similar reason, linear list ("run") of a rbtree node is not iterated, we only check if the new fragment is a subset of the interval covered by existing consecutive fragments. v2: instead of an exact check iterating through linear list of an rbtree node, only check if the new fragment is subset of the "run" (suggested by Eric Dumazet) Fixes: 7969e5c4 ("ip: discard IPv4 datagrams with overlapping segments.") Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
Mao Wenan <maowenan@huawei.com> [bwh: Backported to 4.4: - goto discard_qp, not err, in case of overlap - Set err earlier variable, as done upstream in commit 0ff89efb "ip: fail fast on IP defrag errors"] Signed-off-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Dimitris Michailidis authored
BugLink: https://bugs.launchpad.net/bugs/1818806 commit d55bef50 upstream. We've been getting checksum errors involving small UDP packets, usually 59B packets with 1 extra non-zero padding byte. netdev_rx_csum_fault() has been complaining that HW is providing bad checksums. Turns out the problem is in pskb_trim_rcsum_slow(), introduced in commit 88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"). The source of the problem is that when the bytes we are trimming start at an odd address, as in the case of the 1 padding byte above, skb_checksum() returns a byte-swapped value. We cannot just combine this with skb->csum using csum_sub(). We need to use csum_block_sub() here that takes into account the parity of the start address and handles the swapping. Matches existing code in __skb_postpull_rcsum() and esp_remove_trailer(). Fixes: 88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends") Signed-off-by:
Dimitris Michailidis <dmichail@google.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Eric Dumazet authored
BugLink: https://bugs.launchpad.net/bugs/1818806 commit 0d5b9311 upstream. Multiple cpus might attempt to insert a new fragment in rhashtable, if for example RPS is buggy, as reported by 배석진 in https://patchwork.ozlabs.org/patch/994601/ We use rhashtable_lookup_get_insert_key() instead of rhashtable_insert_fast() to let cpus losing the race free their own inet_frag_queue and use the one that was inserted by another cpu. Fixes: 648700f7 ("inet: frags: use rhashtables for reassembly units") Signed-off-by:
배석진 <soukjin.bae@samsung.com> Signed-off-by:
-
Dan Carpenter authored
BugLink: https://bugs.launchpad.net/bugs/1818806 commit 70837ffe upstream. We accidentally removed the parentheses here, but they are required because '!' has higher precedence than '&'. Fixes: fa0f5273 ("ip: use rb trees for IP frag queue.") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Taehee Yoo authored
BugLink: https://bugs.launchpad.net/bugs/1818806 commit 5d407b07 upstream. A kernel crash occurrs when defragmented packet is fragmented in ip_do_fragment(). In defragment routine, skb_orphan() is called and skb->ip_defrag_offset is set. but skb->sk and skb->ip_defrag_offset are same union member. so that frag->sk is not NULL. Hence crash occurrs in skb->sk check routine in ip_do_fragment() when defragmented packet is fragmented. test commands: %iptables -t nat -I POSTROUTING -j MASQUERADE %hping3 192.168.4.2 -s 1000 -p 2000 -d 60000 splat looks like: [ 261.069429] kernel BUG at net/ipv4/ip_output.c:636! [ 261.075753] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI [ 261.083854] CPU: 1 PID: 1349 Comm: hping3 Not tainted 4.19.0-rc2+ #3 [ 261.100977] RIP: 0010:ip_do_fragment+0x1613/0x2600 [ 261.106945] Code: e8 e2 38 e3 fe 4c 8b 44 24 18 48 8b 74 24 08 e9 92 f6 ff ff 80 3c 02 00 0f 85 da 07 00 00 48 8b b5 d0 00 00 00 e9 25 f6 ff ff <0f> 0b 0f 0b 44 8b 54 24 58 4c 8b 4c 24 18 4c 8b 5c 24 60 4c 8b 6c [ 261.127015] RSP: 0018:ffff8801031cf2c0 EFLAGS: 00010202 [ 261.134156] RAX: 1ffff1002297537b RBX: ffffed0020639e6e RCX: 0000000000000004 [ 261.142156] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff880114ba9bd8 [ 261.150157] RBP: ffff880114ba8a40 R08: ffffed0022975395 R09: ffffed0022975395 [ 261.158157] R10: 0000000000000001 R11: ffffed0022975394 R12: ffff880114ba9ca4 [ 261.166159] R13: 0000000000000010 R14: ffff880114ba9bc0 R15: dffffc0000000000 [ 261.174169] FS: 00007fbae2199700(0000) GS:ffff88011b400000(0000) knlGS:0000000000000000 [ 261.183012] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 261.189013] CR2: 00005579244fe000 CR3: 0000000119bf4000 CR4: 00000000001006e0 [ 261.198158] Call Trace: [ 261.199018] ? dst_output+0x180/0x180 [ 261.205011] ? save_trace+0x300/0x300 [ 261.209018] ? ip_copy_metadata+0xb00/0xb00 [ 261.213034] ? sched_clock_local+0xd4/0x140 [ 261.218158] ? kill_l4proto+0x120/0x120 [nf_conntrack] [ 261.223014] ? rt_cpu_seq_stop+0x10/0x10 [ 261.227014] ? find_held_lock+0x39/0x1c0 [ 261.233008] ip_finish_output+0x51d/0xb50 [ 261.237006] ? ip_fragment.constprop.56+0x220/0x220 [ 261.243011] ? nf_ct_l4proto_register_one+0x5b0/0x5b0 [nf_conntrack] [ 261.250152] ? rcu_is_watching+0x77/0x120 [ 261.255010] ? nf_nat_ipv4_out+0x1e/0x2b0 [nf_nat_ipv4] [ 261.261033] ? nf_hook_slow+0xb1/0x160 [ 261.265007] ip_output+0x1c7/0x710 [ 261.269005] ? ip_mc_output+0x13f0/0x13f0 [ 261.273002] ? __local_bh_enable_ip+0xe9/0x1b0 [ 261.278152] ? ip_fragment.constprop.56+0x220/0x220 [ 261.282996] ? nf_hook_slow+0xb1/0x160 [ 261.287007] raw_sendmsg+0x21f9/0x4420 [ 261.291008] ? dst_output+0x180/0x180 [ 261.297003] ? sched_clock_cpu+0x126/0x170 [ 261.301003] ? find_held_lock+0x39/0x1c0 [ 261.306155] ? stop_critical_timings+0x420/0x420 [ 261.311004] ? check_flags.part.36+0x450/0x450 [ 261.315005] ? _raw_spin_unlock_irq+0x29/0x40 [ 261.320995] ? _raw_spin_unlock_irq+0x29/0x40 [ 261.326142] ? cyc2ns_read_end+0x10/0x10 [ 261.330139] ? raw_bind+0x280/0x280 [ 261.334138] ? sched_clock_cpu+0x126/0x170 [ 261.338995] ? check_flags.part.36+0x450/0x450 [ 261.342991] ? __lock_acquire+0x4500/0x4500 [ 261.348994] ? inet_sendmsg+0x11c/0x500 [ 261.352989] ? dst_output+0x180/0x180 [ 261.357012] inet_sendmsg+0x11c/0x500 [ ... ] v2: - clear skb->sk at reassembly routine.(Eric Dumarzet) Fixes: fa0f5273 ("ip: use rb trees for IP frag queue.") Suggested-by:
Taehee Yoo <ap420073@gmail.com> Reviewed-by:
-
Peter Oskolkov authored
BugLink: https://bugs.launchpad.net/bugs/1818806 commit a4fd284a upstream. This patch changes the runtime behavior of IP defrag queue: incoming in-order fragments are added to the end of the current list/"run" of in-order fragments at the tail. On some workloads, UDP stream performance is substantially improved: RX: ./udp_stream -F 10 -T 2 -l 60 TX: ./udp_stream -c -H <host> -F 10 -T 5 -l 60 with this patchset applied on a 10Gbps receiver: throughput=9524.18 throughput_units=Mbit/s upstream (net-next): throughput=4608.93 throughput_units=Mbit/s Reported-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
Peter Oskolkov <posk@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Florian Westphal <fw@strlen.de> Signed-off-by:
-
