Add helper function is_sata_phy_v2_hw() to judge whether the attached
device is SATA disk for a root PHY.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When SMP IO is sent, sas_protocol_ata couldn't judge whether the disk is
SATA or SAS disk.  So use dev_is_sata to identify SATA or SAS disk.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Unless we actually get some sort of failure in hisi_sas_lu_reset(),
don't print a message.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When an SMP task timeouts, it will call lldd_abort_task to release the
associated slot, and then will release the sas_task.

Currently in lldd_abort_task, if we fail to internally abort IO, then
the slot of SMP IO is not released, but sas_task will still be later
released, so the slot's sas_task is NULL, which will cause NULL pointer
when hisi_sas_slot_task_free happens later.

To resolve, check the return value of internal abort, and release the
slot if it failed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add function for upper-layer to reset controller when all else fails.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For consistency, remove the "hisi_sas_" prefix.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Handle the situation that PHY UP and DOWN irq happen simultaneously.
There is no mechanism of SoC HW to ensure this situation will never
happen. So, we add this handle just in case.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch includes:
(1) Disable transport layer retry
(2) Support CQ time and count interrupt coal
(3) fix link FIFO full issue
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Zhao Nenglong <zhaonenglong@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

There are some rules to decide which error code has the high priority
when errors happen together:

(1) Error phase of CQ decides the error happens on RX or TX;

(2) For TX error, when DMA/TRANS TX error happen simultaneously, the
    priority of DMA TX error is higher than TRANS TX error, so for the
    priority of TX error: DW2 (DMA TX part) > DW0;

(3) For RX error, when TRANS/DMA/SIPC RX error happen simultaneously,
    the priority of TRANS RX error is higher than DMA and SIPC RX error,
    and we should also keep the rules (the priority of DW3 > DW2), so
    for the priority of RX error: DW1 > DW3 > DW2(SIPC RX part);

(4) There are also a priority we should keep in the same error type.

So, modify slot error code to handle this.

In addition to this, some some error codes are modified according to
recommendation from SoC designer.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When a TMF or internal abort times-out, do not free slot. We expect this
to be done upon later escalated error handling.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Some more locking needs to be added/modified for when
read-modify-writing sas_task.task_state_flags.

Note: since we can attempt to grab this lock in interrupt
      context we should use irq variant of spin_lock.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

After hardreset, we clear up IOs of remote disks, so we need to free
those slots in LLDD.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Check in slot_complete_v2_hw() for whether a task has already been
completed by upper layer.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When issuing an LU reset for a SATA target, issue an internal abort and
a hard reset.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Currently an internal abort is executed regardless of the result of the
TMF. We should also check the result of the internal abort to see if we
should free the slot.

So change the status code STAT_IO_COMPLETE to TMF_RESP_FUNC_SUCC,
meaning the slot has been successfully aborted.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For error codes which need abort-and-retry, simulate IO timeout and let
SCSI+ATA layers process those errors.

Previously for SSP, we should try to abort the IO in the LLDD and then
pass back to upper layer, but sometimes this would also error. So
Instead of adding special error handling for this scenario in the LLDD,
allow the upper layer to handle completely.

No performance hit is seen by taking this approach.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

We currently do a hard reset for a link reset. Change this to do a link
reset only.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When sas_port is NULL, then return SAS_PHY_DOWN.

In addition, when the sas_dev is gone then explicitly return
SAS_PHY_DOWN.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Currently when a root PHY is deformed from a asd_sas_port we try to
release the slots in the LLDD, and fail.

Regardless, it is not right to release this early.

This patch removes the deformed function. As it was before, port
deformation is still done in hisi_sas_phy_down().

It would be nice to actually remove the hisi_sas_port_{de}formed() pair,
however we cannot as we need to know the asd_sas_port index libsas has
associated with an asd_sas_phy.

The hw does actually generate a port id for a PHY, but this seems to a
random number, so ignored for this purpose.

This patch also changes the code to link slots to the hisi_sas_device,
and not hisi_sas_port.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add softreset to clear IO after internal abort device for SATA disk.

The SATA error handling for the controller is based on device internal
abort and softreset function.

The controller does not support internal abort for single IO, so we need
to execute internal abort for device.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Relocate the PHY init code from LLDD hw init path to
hisi_sas_scan_start().
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

There are some scenarios that we need to warm-reset to reset registers
of SAS controller. During reset we disable interrupts/DQs/PHYs, and
after reset we re-init the hardware and rescan the topology to see if
anything changed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Introduce function to get hisi_sas_port from asd_sas_port.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This is a bug introduced when they moved the fip subcodes to central
place. Was sending FIP_SC_VL_NOTE in fip.fip_subcode for VLAN request in
fnic_fcoe_send_vlan_req. Change is to use FIP_SC_VL_REQ instead.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The IO and Abort latency counter counts the time taken to complete the
IO and abort command into broad buckets. This is not intended for
performance measurement, just a debug statistic.  current_max_io_time
tries to keep track of the maximum time an IO has taken to complete if
it is > 30sec.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Just a simple counter of number of check conditions encountered on that
host.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

If SCSI-ML has already issued abort on a command i.e
FNIC_IOREQ_ABTS_PENDING is set and we get a IO completion, avoid this
being flagged as out-of-order completion by setting the FNIC_IO_DONE
flag in fnic_fcpio_icmnd_cmpl_handler
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fixing the IO stats update (Active IOs and IO completion) to prevent
"Number of Active IOs" from becoming negative in the fnistats output.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Getting rid of else case to make the flow look bit simpler.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This is to avoid the log from being filled with vlan discovery messages
when there is no vlan configured on the switch.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Not a full cleanup for the IRQ code, for that we'd need to know if the
max number of the various CQ types is going to stay 1 forever.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Buffer is a pointer to the static char array event_buffer and therefore
can never be null, so the check is redundant. Remove it.

Detected by CoverityScan, CID#1077556 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Even if bus is not hot-pluggable, devices can be unbound from the driver
via sysfs, so we should not be using __exit annotations on remove()
methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

1. Add reboot notifier and register it in stex_probe for all supported
   device.

2. For all supported device in restart flow, we get a callback from
   notifier and set S6flag for stex_shutdown & stex_hba_stop to send
   restart command to FW.
Signed-off-by: Charles.Chiou <charles.chiou@tw.promise.com>
Signed-off-by: Paul.Lyu <paul.lyu@tw.promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pegasus series is a RAID support product using Thunderbolt technology.
The newest product, Pegasus 3(P3) supports Thunderbolt 3 technology with
a different chip.

1. Change driver version.

2. Add P3 VID, DID and define it's device address.

3. P3 use msi interrupt, so stex_request_irq P3 type enable msi.

4. For hibernation, use msi_lock in stex_ss_handshake to prevent msi
   register write again when handshaking.

5. P3 doesn't need read() as flush.

6. In stex_ss_intr & stex_abort, P3 only clear interrupt register when
   getting vendor defined interrupt.
Signed-off-by: Charles.Chiou <charles.chiou@tw.promise.com>
Signed-off-by: Paul.Lyu <paul.lyu@tw.promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

refcount_t type and corresponding API should be used instead of atomic_t
when the variable is used as a reference counter. This allows to avoid
accidental refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

refcount_t type and corresponding API should be used instead of atomic_t
when the variable is used as a reference counter. This allows to avoid
accidental refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull some more powerpc fixes from Michael Ellerman:
 "The main item is the addition of the Power9 Machine Check handler.
  This was delayed to make sure some details were correct, and is as
  minimal as possible.

  The rest is small fixes, two for the Power9 PMU, two dealing with
  obscure toolchain problems, two for the PowerNV IOMMU code (used by
  VFIO), and one to fix a crash on 32-bit machines with macio devices
  due to missing dma_ops.

  Thanks to:
    Alexey Kardashevskiy, Cyril Bur, Larry Finger, Madhavan Srinivasan,
    Nicholas Piggin"

* tag 'powerpc-4.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: POWER9 machine check handler
  powerpc/64s: allow machine check handler to set severity and initiator
  powerpc/64s: fix handling of non-synchronous machine checks
  powerpc/pmac: Fix crash in dma-mapping.h with NULL dma_ops
  powerpc/powernv/ioda2: Update iommu table base on ownership change
  powerpc/powernv/ioda2: Gracefully fail if too many TCE levels requested
  selftests/powerpc: Replace stxvx and lxvx with stxvd2x/lxvd2x
  powerpc/perf: Handle sdar_mode for marked event in power9
  powerpc/perf: Fix perf_get_data_addr() for power9 DD1
  powerpc/boot: Fix zImage TOC alignment

Pull x86 platform driver updates from Darren Hart:
 "Asus fixes for the airplane LED and a long awaited fujitsu cleanup.

  asus-wmi:
   - Remove quirk_no_rfkill
   - Detect quirk_no_rfkill from the DSDT

  fujitsu-laptop:
   - remove redundant MODULE_ALIAS entries
   - autodetect LCD interface on all models
   - simplify acpi_bus_register_driver() error handling
   - remove redundant forward declarations
   - replace numeric values with constants
   - rename FUNC_RFKILL to FUNC_FLAGS
   - make platform-related variables match naming convention
   - replace "hotkey" with "laptop" in symbol names
   - clearly denote backlight-related symbols"

* tag 'platform-drivers-x86-v4.11-2' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: asus-wmi: Remove quirk_no_rfkill
  platform/x86: asus-wmi: Detect quirk_no_rfkill from the DSDT
  platform/x86: fujitsu-laptop: remove redundant MODULE_ALIAS entries
  platform/x86: fujitsu-laptop: autodetect LCD interface on all models
  platform/x86: fujitsu-laptop: simplify acpi_bus_register_driver() error handling
  platform/x86: fujitsu-laptop: remove redundant forward declarations
  platform/x86: fujitsu-laptop: replace numeric values with constants
  platform/x86: fujitsu-laptop: rename FUNC_RFKILL to FUNC_FLAGS
  platform/x86: fujitsu-laptop: make platform-related variables match naming convention
  platform/x86: fujitsu-laptop: replace "hotkey" with "laptop" in symbol names
  platform/x86: fujitsu-laptop: clearly denote backlight-related symbols

gup_p4d_range() should call gup_pud_range(), not itself.

[ This was not noticed on x86: this is the HAVE_GENERIC_RCU_GUP code
  used by arm[64] and powerpc    - Linus ]

Fixes: c2febafc ("mm: convert generic code to 5-level paging")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reported-by: Anton Blanchard <anton@samba.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>