[ Upstream commit d144dfea ]

If we use USB ID pin as wakeup source, and there is a USB block
device on this USB OTG (ID) cable, the system will be deadlock
after system resume.

The root cause for this problem is: the workqueue ci_otg may try
to remove hcd before the driver resume has finished, and hcd will
disconnect the device on it, then, it will call device_release_driver,
and holds the device lock "dev->mutex", but it is never unlocked since
it waits workqueue writeback to run to flush the block information, but
the workqueue writeback is freezable, it is not thawed before driver
resume has finished.

When the driver (device: sd 0:0:0:0:) resume goes to dpm_complete, it
tries to get its device lock "dev->mutex", but it can't get it forever,
then the deadlock occurs. Below call stacks show the situation.

So, in order to fix this problem, we need to change workqueue ci_otg
as freezable, then the work item in this workqueue will be run after
driver's resume, this workqueue will not be blocked forever like above
case since the workqueue writeback has been thawed too.

Tested at: i.mx6qdl-sabresd and i.mx6sx-sdb.

[  555.178869] kworker/u2:13   D c07de74c     0   826      2 0x00000000
[  555.185310] Workqueue: ci_otg ci_otg_work
[  555.189353] Backtrace:
[  555.191849] [<c07de4fc>] (__schedule) from [<c07dec6c>] (schedule+0x48/0xa0)
[  555.198912]  r10:ee471ba0 r9:00000000 r8:00000000 r7:00000002 r6:ee470000 r5:ee471ba4
[  555.206867]  r4:ee470000
[  555.209453] [<c07dec24>] (schedule) from [<c07e2fc4>] (schedule_timeout+0x15c/0x1e0)
[  555.217212]  r4:7fffffff r3:edc2b000
[  555.220862] [<c07e2e68>] (schedule_timeout) from [<c07df6c8>] (wait_for_common+0x94/0x144)
[  555.229140]  r8:00000000 r7:00000002 r6:ee470000 r5:ee471ba4 r4:7fffffff
[  555.235980] [<c07df634>] (wait_for_common) from [<c07df790>] (wait_for_completion+0x18/0x1c)
[  555.244430]  r10:00000001 r9:c0b5563c r8:c0042e48 r7:ef086000 r6:eea4372c r5:ef131b00
[  555.252383]  r4:00000000
[  555.254970] [<c07df778>] (wait_for_completion) from [<c0043cb8>] (flush_work+0x19c/0x234)
[  555.263177] [<c0043b1c>] (flush_work) from [<c0043fac>] (flush_delayed_work+0x48/0x4c)
[  555.271106]  r8:ed5b5000 r7:c0b38a3c r6:eea439cc r5:eea4372c r4:eea4372c
[  555.277958] [<c0043f64>] (flush_delayed_work) from [<c00eae18>] (bdi_unregister+0x84/0xec)
[  555.286236]  r4:eea43520 r3:20000153
[  555.289885] [<c00ead94>] (bdi_unregister) from [<c02c2154>] (blk_cleanup_queue+0x180/0x29c)
[  555.298250]  r5:eea43808 r4:eea43400
[  555.301909] [<c02c1fd4>] (blk_cleanup_queue) from [<c0417914>] (__scsi_remove_device+0x48/0xb8)
[  555.310623]  r7:00000000 r6:20000153 r5:ededa950 r4:ededa800
[  555.316403] [<c04178cc>] (__scsi_remove_device) from [<c0415e90>] (scsi_forget_host+0x64/0x68)
[  555.325028]  r5:ededa800 r4:ed5b5000
[  555.328689] [<c0415e2c>] (scsi_forget_host) from [<c0409828>] (scsi_remove_host+0x78/0x104)
[  555.337054]  r5:ed5b5068 r4:ed5b5000
[  555.340709] [<c04097b0>] (scsi_remove_host) from [<c04cdfcc>] (usb_stor_disconnect+0x50/0xb4)
[  555.349247]  r6:ed5b56e4 r5:ed5b5818 r4:ed5b5690 r3:00000008
[  555.355025] [<c04cdf7c>] (usb_stor_disconnect) from [<c04b3bc8>] (usb_unbind_interface+0x78/0x25c)
[  555.363997]  r8:c13919b4 r7:edd3c000 r6:edd3c020 r5:ee551c68 r4:ee551c00 r3:c04cdf7c
[  555.371892] [<c04b3b50>] (usb_unbind_interface) from [<c03dc248>] (__device_release_driver+0x8c/0x118)
[  555.381213]  r10:00000001 r9:edd90c00 r8:c13919b4 r7:ee551c68 r6:c0b546e0 r5:c0b5563c
[  555.389167]  r4:edd3c020
[  555.391752] [<c03dc1bc>] (__device_release_driver) from [<c03dc2fc>] (device_release_driver+0x28/0x34)
[  555.401071]  r5:edd3c020 r4:edd3c054
[  555.404721] [<c03dc2d4>] (device_release_driver) from [<c03db304>] (bus_remove_device+0xe0/0x110)
[  555.413607]  r5:edd3c020 r4:ef17f04c
[  555.417253] [<c03db224>] (bus_remove_device) from [<c03d8128>] (device_del+0x114/0x21c)
[  555.425270]  r6:edd3c028 r5:edd3c020 r4:ee551c00 r3:00000000
[  555.431045] [<c03d8014>] (device_del) from [<c04b1560>] (usb_disable_device+0xa4/0x1e8)
[  555.439061]  r8:edd3c000 r7:eded8000 r6:00000000 r5:00000001 r4:ee551c00
[  555.445906] [<c04b14bc>] (usb_disable_device) from [<c04a8e54>] (usb_disconnect+0x74/0x224)
[  555.454271]  r9:edd90c00 r8:ee551000 r7:ee551c68 r6:ee551c9c r5:ee551c00 r4:00000001
[  555.462156] [<c04a8de0>] (usb_disconnect) from [<c04a8fb8>] (usb_disconnect+0x1d8/0x224)
[  555.470259]  r10:00000001 r9:edd90000 r8:ee471e2c r7:ee551468 r6:ee55149c r5:ee551400
[  555.478213]  r4:00000001
[  555.480797] [<c04a8de0>] (usb_disconnect) from [<c04ae5ec>] (usb_remove_hcd+0xa0/0x1ac)
[  555.488813]  r10:00000001 r9:ee471eb0 r8:00000000 r7:ef3d9500 r6:eded810c r5:eded80b0
[  555.496765]  r4:eded8000
[  555.499351] [<c04ae54c>] (usb_remove_hcd) from [<c04d4158>] (host_stop+0x28/0x64)
[  555.506847]  r6:eeb50010 r5:eded8000 r4:eeb51010
[  555.511563] [<c04d4130>] (host_stop) from [<c04d09b8>] (ci_otg_work+0xc4/0x124)
[  555.518885]  r6:00000001 r5:eeb50010 r4:eeb502a0 r3:c04d4130
[  555.524665] [<c04d08f4>] (ci_otg_work) from [<c00454f0>] (process_one_work+0x194/0x420)
[  555.532682]  r6:ef086000 r5:eeb502a0 r4:edc44480
[  555.537393] [<c004535c>] (process_one_work) from [<c00457b0>] (worker_thread+0x34/0x514)
[  555.545496]  r10:edc44480 r9:ef086000 r8:c0b1a100 r7:ef086034 r6:00000088 r5:edc44498
[  555.553450]  r4:ef086000
[  555.556032] [<c004577c>] (worker_thread) from [<c004bab4>] (kthread+0xdc/0xf8)
[  555.563268]  r10:00000000 r9:00000000 r8:00000000 r7:c004577c r6:edc44480 r5:eddc15c0
[  555.571221]  r4:00000000
[  555.573804] [<c004b9d8>] (kthread) from [<c000fef0>] (ret_from_fork+0x14/0x24)
[  555.581040]  r7:00000000 r6:00000000 r5:c004b9d8 r4:eddc15c0

[  553.429383] sh              D c07de74c     0   694    691 0x00000000
[  553.435801] Backtrace:
[  553.438295] [<c07de4fc>] (__schedule) from [<c07dec6c>] (schedule+0x48/0xa0)
[  553.445358]  r10:edd3c054 r9:edd3c078 r8:edddbd50 r7:edcbbc00 r6:c1377c34 r5:60000153
[  553.453313]  r4:eddda000
[  553.455896] [<c07dec24>] (schedule) from [<c07deff8>] (schedule_preempt_disabled+0x10/0x14)
[  553.464261]  r4:edd3c058 r3:0000000a
[  553.467910] [<c07defe8>] (schedule_preempt_disabled) from [<c07e0bbc>] (mutex_lock_nested+0x1a0/0x3e8)
[  553.477254] [<c07e0a1c>] (mutex_lock_nested) from [<c03e927c>] (dpm_complete+0xc0/0x1b0)
[  553.485358]  r10:00561408 r9:edd3c054 r8:c0b4863c r7:edddbd90 r6:c0b485d8 r5:edd3c020
[  553.493313]  r4:edd3c0d0
[  553.495896] [<c03e91bc>] (dpm_complete) from [<c03e9388>] (dpm_resume_end+0x1c/0x20)
[  553.503652]  r9:00000000 r8:c0b1a9d0 r7:c1334ec0 r6:c1334edc r5:00000003 r4:00000010
[  553.511544] [<c03e936c>] (dpm_resume_end) from [<c0079894>] (suspend_devices_and_enter+0x158/0x504)
[  553.520604]  r4:00000000 r3:c1334efc
[  553.524250] [<c007973c>] (suspend_devices_and_enter) from [<c0079e74>] (pm_suspend+0x234/0x2cc)
[  553.532961]  r10:00561408 r9:ed6b7300 r8:00000004 r7:c1334eec r6:00000000 r5:c1334ee8
[  553.540914]  r4:00000003
[  553.543493] [<c0079c40>] (pm_suspend) from [<c0078a6c>] (state_store+0x6c/0xc0)

[  555.703684] 7 locks held by kworker/u2:13/826:
[  555.708140]  #0:  ("%s""ci_otg"){++++.+}, at: [<c0045484>] process_one_work+0x128/0x420
[  555.716277]  #1:  ((&ci->work)){+.+.+.}, at: [<c0045484>] process_one_work+0x128/0x420
[  555.724317]  #2:  (usb_bus_list_lock){+.+.+.}, at: [<c04ae5e4>] usb_remove_hcd+0x98/0x1ac
[  555.732626]  #3:  (&dev->mutex){......}, at: [<c04a8e28>] usb_disconnect+0x48/0x224
[  555.740403]  #4:  (&dev->mutex){......}, at: [<c04a8e28>] usb_disconnect+0x48/0x224
[  555.748179]  #5:  (&dev->mutex){......}, at: [<c03dc2f4>] device_release_driver+0x20/0x34
[  555.756487]  #6:  (&shost->scan_mutex){+.+.+.}, at: [<c04097d0>] scsi_remove_host+0x20/0x104

Cc: <stable@vger.kernel.org> #v3.14+
Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit dbc0d3ca ]

ceph_msg_footer is 21 bytes long, while ceph_msg_footer_old is only 13.
Don't skip too much when CEPH_FEATURE_MSG_AUTH isn't negotiated.

Cc: stable@vger.kernel.org # 3.19+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit e7a88e82 ]

The contract between try_read() and try_write() is that when called
each processes as much data as possible.  When instructed by osd_client
to skip a message, try_read() is violating this contract by returning
after receiving and discarding a single message instead of checking for
more.  try_write() then gets a chance to write out more requests,
generating more replies/skips for try_read() to handle, forcing the
messenger into a starvation loop.

Cc: stable@vger.kernel.org # 3.10+
Reported-by: Varada Kari <Varada.Kari@sandisk.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Varada Kari <Varada.Kari@sandisk.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d045437a ]

The ftrace:function event is only displayed for parsing the function tracer
data. It is not used to enable function tracing, and does not include an
"enable" file in its event directory.

Originally, this event was kept separate from other events because it did
not have a ->reg parameter. But perf added a "reg" parameter for its use
which caused issues, because it made the event available to functions where
it was not compatible for.

Commit 9b63776f "tracing: Do not enable function event with enable"
added a TRACE_EVENT_FL_IGNORE_ENABLE flag that prevented the function event
from being enabled by normal trace events. But this commit missed keeping
the function event from being displayed by the "available_events" directory,
which is used to show what events can be enabled by set_event.

One documented way to enable all events is to:

 cat available_events > set_event

But because the function event is displayed in the available_events, this
now causes an INVALID error:

 cat: write error: Invalid argument
Reported-by: Chunyu Hu <chuhu@redhat.com>
Fixes: 9b63776f "tracing: Do not enable function event with enable"
Cc: stable@vger.kernel.org # 3.4+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d7444794 ]

In async_pf we try to allocate with NOWAIT to get an element quickly
or fail. This code also handle failures gracefully. Lets silence
potential page allocation failures under load.

qemu-system-s39: page allocation failure: order:0,mode:0x2200000
[...]
Call Trace:
([<00000000001146b8>] show_trace+0xf8/0x148)
[<000000000011476a>] show_stack+0x62/0xe8
[<00000000004a36b8>] dump_stack+0x70/0x98
[<0000000000272c3a>] warn_alloc_failed+0xd2/0x148
[<000000000027709e>] __alloc_pages_nodemask+0x94e/0xb38
[<00000000002cd36a>] new_slab+0x382/0x400
[<00000000002cf7ac>] ___slab_alloc.constprop.30+0x2dc/0x378
[<00000000002d03d0>] kmem_cache_alloc+0x160/0x1d0
[<0000000000133db4>] kvm_setup_async_pf+0x6c/0x198
[<000000000013dee8>] kvm_arch_vcpu_ioctl_run+0xd48/0xd58
[<000000000012fcaa>] kvm_vcpu_ioctl+0x372/0x690
[<00000000002f66f6>] do_vfs_ioctl+0x3be/0x510
[<00000000002f68ec>] SyS_ioctl+0xa4/0xb8
[<0000000000781c5e>] system_call+0xd6/0x264
[<000003ffa24fa06a>] 0x3ffa24fa06a

Cc: stable@vger.kernel.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 172b2386 ]

Sometimes when setting a breakpoint a process doesn't stop on it.
This is because the debug registers are not loaded correctly on
VCPU load.

The following simple reproducer from Oleg Nesterov tries using debug
registers in two threads.  To see the bug, run a 2-VCPU guest with
"taskset -c 0" and run "./bp 0 1" inside the guest.

    #include <unistd.h>
    #include <signal.h>
    #include <stdlib.h>
    #include <stdio.h>
    #include <sys/wait.h>
    #include <sys/ptrace.h>
    #include <sys/user.h>
    #include <asm/debugreg.h>
    #include <assert.h>

    #define offsetof(TYPE, MEMBER) ((size_t) &((TYPE *)0)->MEMBER)

    unsigned long encode_dr7(int drnum, int enable, unsigned int type, unsigned int len)
    {
        unsigned long dr7;

        dr7 = ((len | type) & 0xf)
            << (DR_CONTROL_SHIFT + drnum * DR_CONTROL_SIZE);
        if (enable)
            dr7 |= (DR_GLOBAL_ENABLE << (drnum * DR_ENABLE_SIZE));

        return dr7;
    }

    int write_dr(int pid, int dr, unsigned long val)
    {
        return ptrace(PTRACE_POKEUSER, pid,
                offsetof (struct user, u_debugreg[dr]),
                val);
    }

    void set_bp(pid_t pid, void *addr)
    {
        unsigned long dr7;
        assert(write_dr(pid, 0, (long)addr) == 0);
        dr7 = encode_dr7(0, 1, DR_RW_EXECUTE, DR_LEN_1);
        assert(write_dr(pid, 7, dr7) == 0);
    }

    void *get_rip(int pid)
    {
        return (void*)ptrace(PTRACE_PEEKUSER, pid,
                offsetof(struct user, regs.rip), 0);
    }

    void test(int nr)
    {
        void *bp_addr = &&label + nr, *bp_hit;
        int pid;

        printf("test bp %d\n", nr);
        assert(nr < 16); // see 16 asm nops below

        pid = fork();
        if (!pid) {
            assert(ptrace(PTRACE_TRACEME, 0,0,0) == 0);
            kill(getpid(), SIGSTOP);
            for (;;) {
                label: asm (
                    "nop; nop; nop; nop;"
                    "nop; nop; nop; nop;"
                    "nop; nop; nop; nop;"
                    "nop; nop; nop; nop;"
                );
            }
        }

        assert(pid == wait(NULL));
        set_bp(pid, bp_addr);

        for (;;) {
            assert(ptrace(PTRACE_CONT, pid, 0, 0) == 0);
            assert(pid == wait(NULL));

            bp_hit = get_rip(pid);
            if (bp_hit != bp_addr)
                fprintf(stderr, "ERR!! hit wrong bp %ld != %d\n",
                    bp_hit - &&label, nr);
        }
    }

    int main(int argc, const char *argv[])
    {
        while (--argc) {
            int nr = atoi(*++argv);
            if (!fork())
                test(nr);
        }

        while (wait(NULL) > 0)
            ;
        return 0;
    }

Cc: stable@vger.kernel.org
Suggested-by: Nadav Amit <namit@cs.technion.ac.il>
Reported-by: Andrey Wagin <avagin@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 236cf17c ]

When we allocate bitmaps in vgic_vcpu_init_maps, we divide the number of
bits we need by 8 to figure out how many bytes to allocate. However,
bitmap elements are always accessed as unsigned longs, and if we didn't
happen to allocate a size such that size % sizeof(unsigned long) == 0,
bitmap accesses may go past the end of the allocation.

When using KASAN (which does byte-granular access checks), this results
in a continuous stream of BUGs whenever these bitmaps are accessed:

=============================================================================
BUG kmalloc-128 (Tainted: G    B          ): kasan: bad access detected
-----------------------------------------------------------------------------

INFO: Allocated in vgic_init.part.25+0x55c/0x990 age=7493 cpu=3 pid=1730
INFO: Slab 0xffffffbde6d5da40 objects=16 used=15 fp=0xffffffc935769700 flags=0x4000000000000080
INFO: Object 0xffffffc935769500 @offset=1280 fp=0x          (null)

Bytes b4 ffffffc9357694f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769510: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769520: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769530: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769540: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769550: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769560: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769570: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
CPU: 3 PID: 1740 Comm: kvm-vcpu-0 Tainted: G    B           4.4.0+ #17
Hardware name: ARM Juno development board (r1) (DT)
Call trace:
[<ffffffc00008e770>] dump_backtrace+0x0/0x280
[<ffffffc00008ea04>] show_stack+0x14/0x20
[<ffffffc000726360>] dump_stack+0x100/0x188
[<ffffffc00030d324>] print_trailer+0xfc/0x168
[<ffffffc000312294>] object_err+0x3c/0x50
[<ffffffc0003140fc>] kasan_report_error+0x244/0x558
[<ffffffc000314548>] __asan_report_load8_noabort+0x48/0x50
[<ffffffc000745688>] __bitmap_or+0xc0/0xc8
[<ffffffc0000d9e44>] kvm_vgic_flush_hwstate+0x1bc/0x650
[<ffffffc0000c514c>] kvm_arch_vcpu_ioctl_run+0x2ec/0xa60
[<ffffffc0000b9a6c>] kvm_vcpu_ioctl+0x474/0xa68
[<ffffffc00036b7b0>] do_vfs_ioctl+0x5b8/0xcb0
[<ffffffc00036bf34>] SyS_ioctl+0x8c/0xa0
[<ffffffc000086cb0>] el0_svc_naked+0x24/0x28
Memory state around the buggy address:
 ffffffc935769400: 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffffffc935769480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffffffc935769500: 04 fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
                   ^
 ffffffc935769580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffffffc935769600: 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================

Fix the issue by always allocating a multiple of sizeof(unsigned long),
as we do elsewhere in the vgic code.

Fixes: c1bfb577 ("arm/arm64: KVM: vgic: switch to dynamic allocation")
Cc: stable@vger.kernel.org
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit b7052cd7 ]

The qword_get() function NUL-terminates its output buffer.  If the input
string is in hex format \xXXXX... and the same length as the output
buffer, there is an off-by-one:

  int qword_get(char **bpp, char *dest, int bufsize)
  {
      ...
      while (len < bufsize) {
          ...
          *dest++ = (h << 4) | l;
          len++;
      }
      ...
      *dest = '\0';
      return len;
  }

This patch ensures the NUL terminator doesn't fall outside the output
buffer.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 39d42750 ]

set_power_state defaults to no displays, so we need to update
the display configuration after setting up the powerstate on the
first call. In most cases this is not an issue since ends up
getting called multiple times at any given modeset and the proper
order is achieved in the display changed handling at the top of
the function.
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Jordan Lazare <Jordan.Lazare@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 342300cc ]

git commit 80703617
"s390: add support for vector extension"
broke 31-bit compat processes in regard to signal handling.

The restore_sigregs_ext32() function is used to restore the additional
elements from the user space signal frame. Among the additional elements
are the upper registers halves for 64-bit register support for 31-bit
processes. The copy_from_user that is used to retrieve the high-gprs
array from the user stack uses an incorrect length, 8 bytes instead of
64 bytes. This causes incorrect upper register halves to get loaded.

Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 4328daa2 ]

Using request-based DM mpath configured with the following stacking
(.request_fn DM mpath ontop of scsi-mq paths):

echo Y > /sys/module/scsi_mod/parameters/use_blk_mq
echo N > /sys/module/dm_mod/parameters/use_blk_mq

'struct dm_rq_target_io' would leak if a request is requeued before a
blk-mq clone is allocated (or fails to allocate).  free_rq_tio()
wasn't being called.

kmemleak reported:

unreferenced object 0xffff8800b90b98c0 (size 112):
  comm "kworker/7:1H", pid 5692, jiffies 4295056109 (age 78.589s)
  hex dump (first 32 bytes):
    00 d0 5c 2c 03 88 ff ff 40 00 bf 01 00 c9 ff ff  ..\,....@.......
    e0 d9 b1 34 00 88 ff ff 00 00 00 00 00 00 00 00  ...4............
  backtrace:
    [<ffffffff81672b6e>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff811dbb63>] kmem_cache_alloc+0xc3/0x1e0
    [<ffffffff8117eae5>] mempool_alloc_slab+0x15/0x20
    [<ffffffff8117ec1e>] mempool_alloc+0x6e/0x170
    [<ffffffffa00029ac>] dm_old_prep_fn+0x3c/0x180 [dm_mod]
    [<ffffffff812fbd78>] blk_peek_request+0x168/0x290
    [<ffffffffa0003e62>] dm_request_fn+0xb2/0x1b0 [dm_mod]
    [<ffffffff812f66e3>] __blk_run_queue+0x33/0x40
    [<ffffffff812f9585>] blk_delay_work+0x25/0x40
    [<ffffffff81096fff>] process_one_work+0x14f/0x3d0
    [<ffffffff81097715>] worker_thread+0x125/0x4b0
    [<ffffffff8109ce88>] kthread+0xd8/0xf0
    [<ffffffff8167cb8f>] ret_from_fork+0x3f/0x70
    [<ffffffffffffffff>] 0xffffffffffffffff

crash> struct -o dm_rq_target_io
struct dm_rq_target_io {
    ...
}
SIZE: 112

Fixes: e5863d9a ("dm: allocate requests in target when stacking on blk-mq devices")
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 90cfde46 ]

This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 7a64cd88 ]

There's one point was missed in the patch commit da49889d ("staging:
binder: Support concurrent 32 bit and 64 bit processes."). When configure
BINDER_IPC_32BIT, the size of binder_uintptr_t was 32bits, but size of
void * is 64bit on 64bit system. Correct it here.
Signed-off-by: Lisa Du <cldu@marvell.com>
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Fixes: da49889d ("staging: binder: Support concurrent 32 bit and 64 bit processes.")
Cc: <stable@vger.kernel.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 000e0949 ]

Thermal hook gpio_fan_get_cur_state is only interested in knowing
the current speed index that was setup in the system, this is
already available as part of fan_data->speed_index which is always
set by set_fan_speed. Using get_fan_speed_index is useful when we
have no idea about the fan speed configuration (for example during
fan_ctrl_init).

When thermal framework invokes
gpio_fan_get_cur_state=>get_fan_speed_index via gpio_fan_get_cur_state
especially in a polled configuration for thermal governor, we
basically hog the i2c interface to the extent that other functions
fail to get any traffic out :(.

Instead, just provide the last state set in the driver - since the gpio
fan driver is responsible for the fan state immaterial of override, the
fan_data->speed_index should accurately reflect the state.

Fixes: b5cf88e4 ("(gpio-fan): Add thermal control hooks")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit acc14694 ]

Make the divisor signed as DIV_ROUND_CLOSEST is undefined for negative
dividends when the divisor is unsigned.
Signed-off-by: Peter Rosin <peda@axentia.se>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit f5bdd66c ]

This patch complements the list of device IDs previously
added for lewisburg sata.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 56e74338 ]

Adding Intel codename Lewisburg platform device IDs for SATA.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 4d92f009 ]

This change was to preserve the ascending order of device IDs.
There was an exception with the first two Lewisburg device IDs to
keep all device IDs of the same kind grouped by code name.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d061c1ca ]

Thomas reports:

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=05c6 ProdID=6001 Rev=00.00
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Cc: <stable@vger.kernel.org>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 6627ae19 ]

Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 3158a8d4 ]

$ lsusb:
Bus 001 Device 101: ID 1e0e:9001 Qualcomm / Option

$ usb-devices:
T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=101 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  2
P:  Vendor=1e0e ProdID=9001 Rev= 2.32
S:  Manufacturer=SimTech, Incorporated
S:  Product=SimTech, Incorporated
S:  SerialNumber=0123456789ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)

The last interface (6) is used for Android Composite ADB interface.

Serial port layout:
0: QCDM/DIAG
1: NMEA
2: AT
3: AT/PPP
4: audio
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d9dfd8d7 ]

In the case where d_add_unique() finds an appropriate alias to use it will
have already incremented the reference count.  An additional dget() to swap
the open context's dentry is unnecessary and will leak a reference.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Fixes: 275bb307 ("NFSv4: Move dentry instantiation into the NFSv4-...")
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit c4509601 ]

The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda618 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.

The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:

1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.

2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).

The following simplified method is used instead:

All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.

This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.

Fixes: aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 0ba4581c ]

The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org>      # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 4d8c8bd6 ]

Occasionaly PV guests would crash with:

pciback 0000:00:00.1: Xen PCI mapped GSI0 to IRQ16
BUG: unable to handle kernel paging request at 0000000d1a8c0be0
.. snip..
  <ffffffff8139ce1b>] find_next_bit+0xb/0x10
  [<ffffffff81387f22>] cpumask_next_and+0x22/0x40
  [<ffffffff813c1ef8>] pci_device_probe+0xb8/0x120
  [<ffffffff81529097>] ? driver_sysfs_add+0x77/0xa0
  [<ffffffff815293e4>] driver_probe_device+0x1a4/0x2d0
  [<ffffffff813c1ddd>] ? pci_match_device+0xdd/0x110
  [<ffffffff81529657>] __device_attach_driver+0xa7/0xb0
  [<ffffffff815295b0>] ? __driver_attach+0xa0/0xa0
  [<ffffffff81527622>] bus_for_each_drv+0x62/0x90
  [<ffffffff8152978d>] __device_attach+0xbd/0x110
  [<ffffffff815297fb>] device_attach+0xb/0x10
  [<ffffffff813b75ac>] pci_bus_add_device+0x3c/0x70
  [<ffffffff813b7618>] pci_bus_add_devices+0x38/0x80
  [<ffffffff813dc34e>] pcifront_scan_root+0x13e/0x1a0
  [<ffffffff817a0692>] pcifront_backend_changed+0x262/0x60b
  [<ffffffff814644c6>] ? xenbus_gather+0xd6/0x160
  [<ffffffff8120900f>] ? put_object+0x2f/0x50
  [<ffffffff81465c1d>] xenbus_otherend_changed+0x9d/0xa0
  [<ffffffff814678ee>] backend_changed+0xe/0x10
  [<ffffffff81463a28>] xenwatch_thread+0xc8/0x190
  [<ffffffff810f22f0>] ? woken_wake_function+0x10/0x10

which was the result of two things:

When we call pci_scan_root_bus we would pass in 'sd' (sysdata)
pointer which was an 'pcifront_sd' structure. However in the
pci_device_add it expects that the 'sd' is 'struct sysdata' and
sets the dev->node to what is in sd->node (offset 4):

set_dev_node(&dev->dev, pcibus_to_node(bus));

 __pcibus_to_node(const struct pci_bus *bus)
{
        const struct pci_sysdata *sd = bus->sysdata;

        return sd->node;
}

However our structure was pcifront_sd which had nothing at that
offset:

struct pcifront_sd {
        int                        domain;    /*     0     4 */
        /* XXX 4 bytes hole, try to pack */
        struct pcifront_device *   pdev;      /*     8     8 */
}

That is an hole - filled with garbage as we used kmalloc instead of
kzalloc (the second problem).

This patch fixes the issue by:
 1) Use kzalloc to initialize to a well known state.
 2) Put 'struct pci_sysdata' at the start of 'pcifront_sd'. That
    way access to the 'node' will access the right offset.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d52a2481 ]

commit 8d47065f upstream.

Commit 408fb0e5 (xen/pciback: Don't
allow MSI-X ops if PCI_COMMAND_MEMORY is not set) prevented enabling
MSI-X on passed-through virtual functions, because it checked the VF
for PCI_COMMAND_MEMORY but this is not a valid bit for VFs.

Instead, check the physical function for PCI_COMMAND_MEMORY.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 408fb0e5 ]

commit f598282f ("PCI: Fix the NIU MSI-X problem in a better way")
teaches us that dealing with MSI-X can be troublesome.

Further checks in the MSI-X architecture shows that if the
PCI_COMMAND_MEMORY bit is turned of in the PCI_COMMAND we
may not be able to access the BAR (since they are memory regions).

Since the MSI-X tables are located in there.. that can lead
to us causing PCIe errors. Inhibit us performing any
operation on the MSI-X unless the MEMORY bit is set.

Note that Xen hypervisor with:
"x86/MSI-X: access MSI-X table only after having enabled MSI-X"
will return:
xen_pciback: 0000:0a:00.1: error -6 enabling MSI-X for guest 3!

When the generic MSI code tries to setup the PIRQ without
MEMORY bit set. Which means with later versions of Xen
(4.6) this patch is not neccessary.

This is part of XSA-157

CC: stable@vger.kernel.org
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 5e0ce145 ]

The guest sequence of:

  a) XEN_PCI_OP_enable_msix
  b) XEN_PCI_OP_enable_msix

results in hitting an NULL pointer due to using freed pointers.

The device passed in the guest MUST have MSI-X capability.

The a) constructs and SysFS representation of MSI and MSI groups.
The b) adds a second set of them but adding in to SysFS fails (duplicate entry).
'populate_msi_sysfs' frees the newly allocated msi_irq_groups (note that
in a) pdev->msi_irq_groups is still set) and also free's ALL of the
MSI-X entries of the device (the ones allocated in step a) and b)).

The unwind code: 'free_msi_irqs' deletes all the entries and tries to
delete the pdev->msi_irq_groups (which hasn't been set to NULL).
However the pointers in the SysFS are already freed and we hit an
NULL pointer further on when 'strlen' is attempted on a freed pointer.

The patch adds a simple check in the XEN_PCI_OP_enable_msix to guard
against that. The check for msi_enabled is not stricly neccessary.

This is part of XSA-157

CC: stable@vger.kernel.org
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 4cf5aa2f ]

commit d159457b upstream.

Commit 8135cf8b (xen/pciback: Save
xen_pci_op commands before processing it) broke enabling MSI-X because
it would never copy the resulting vectors into the response.  The
number of vectors requested was being overwritten by the return value
(typically zero for success).

Save the number of vectors before processing the op, so the correct
number of vectors are copied afterwards.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 8135cf8b ]

Double fetch vulnerabilities that happen when a variable is
fetched twice from shared memory but a security check is only
performed the first time.

The xen_pcibk_do_op function performs a switch statements on the op->cmd
value which is stored in shared memory. Interestingly this can result
in a double fetch vulnerability depending on the performed compiler
optimization.

This patch fixes it by saving the xen_pci_op command before
processing it. We also use 'barrier' to make sure that the
compiler does not perform any optimization.

This is part of XSA155.

CC: stable@vger.kernel.org
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 5e56276e ]

The firmware can perform a scheduled scan with not matchsets passed,
but it can't send notification that results were found.  Since the
userspace then cannot know when we got new results and the firmware
wouldn't trigger a wake in case we are sleeping, it's better not to
allow scans without matchsets.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=110831

Cc: <stable@vger.kernel.org> [3.17+]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[SL: Backport to 4.1]
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 287e6611 ]

As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not
work correctly in compat mode with libata.

I have investigated the issue further and found multiple problems
that all appeared with the same commit that originally introduced
HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably
also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy
a 'long' variable containing either 0 or 1 to user space.

The problems with this are:

* On big-endian machines, this will always write a zero because it
  stores the wrong byte into user space.

* In compat mode, the upper three bytes of the variable are updated
  by the compat_hdio_ioctl() function, but they now contain
  uninitialized stack data.

* The hdparm tool calling this ioctl uses a 'static long' variable
  to store the result. This means at least the upper bytes are
  initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT
  would fill them with data that remains stale when the low byte
  is overwritten. Fortunately libata doesn't implement any of the
  affected ioctl commands, so this would only happen when we query
  both an IDE and an ATA device in the same command such as
  "hdparm -N -c /dev/hda /dev/sda"

* The libata code for unknown reasons started using ATA_IOC_GET_IO32
  and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT,
  while the ioctl commands that were added later use the normal
  HDIO_* names. This is harmless but rather confusing.

This addresses all four issues by changing the code to use put_user()
on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem
does, and by clarifying the names of the ioctl commands.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Soohoon Lee <Soohoon.Lee@f5.com>
Tested-by: Soohoon Lee <Soohoon.Lee@f5.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 50ab8ec7 ]

See http: //www.infradead.org/rpr.html
X-Evolution-Source: 1451162204.2173.11@leira.trondhjem.org
Content-Transfer-Encoding: 8bit
Mime-Version: 1.0

We support OFFSET_MAX just fine, so don't round down below it.  Also
switch to using min_t to make the helper more readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 433c9237 ("NFS: Clean up nfs_size_to_loff_t()")
Cc: stable@vger.kernel.org # 2.6.23+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit f285aa8d ]

When adding a new frontend to xen-scsiback don't decrement the number
of active frontends in case of no error. Doing so results in a failure
when trying to remove the xen-pvscsi nexus even if no domain is using
it.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit c8ad7063 ]

Building perf out of kernel tree is currently broken because the
MANIFEST file refers to kernel files that have been removed. With this
patch make perf-targz-src-pkg succeeds as does building perf using the
generated tarfile.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Link: http://lkml.kernel.org/r/1433526173-172332-1-git-send-email-david.ahern@oracle.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

The linux-4.1.y specific patch to fix a previous v4.1 UNIT_ATTENTION
read-copy-update conversion regression:

  commit 35afa656
  Author: Nicholas Bellinger <nab@linux-iscsi.org>
  Date:   Wed Sep 23 07:49:26 2015 +0000

      target: Fix v4.1 UNIT_ATTENTION se_node_acl->device_list[] NULL pointer

introduced the following compile warning:

  drivers/target/target_core_pr.c: In function ‘core_scsi3_pr_seq_non_holder’:
  drivers/target/target_core_pr.c:332:3: warning: ‘return’ with no value, in function returning non-void [-Wreturn-type]

Go ahead and fix this up to always returning zero when no ACL
device list exists within core_scsi3_pr_seq_non_holder().
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

commit 310d3d31 upstream.

This patch fixes a race between setting of SCF_SEND_DELAYED_TAS
in transport_send_task_abort(), and check of the same bit in
transport_check_aborted_status().

It adds a __transport_check_aborted_status() version that is
used by target_execute_cmd() when se_cmd->t_state_lock is
held, and a transport_check_aborted_status() wrapper for
all other existing callers.

Also, it handles the case where the check happens before
transport_send_task_abort() gets called.  For this, go
ahead and set SCF_SEND_DELAYED_TAS early when necessary,
and have transport_send_task_abort() send the abort.

Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

commit 0f4a9431 upstream.

To address the bug where fabric driver level shutdown
of se_cmd occurs at the same time when TMR CMD_T_ABORTED
is happening resulting in a -1 ->cmd_kref, this patch
adds a CMD_T_FABRIC_STOP bit that is used to determine
when TMR + driver I_T nexus shutdown is happening
concurrently.

It changes target_sess_cmd_list_set_waiting() to obtain
se_cmd->cmd_kref + set CMD_T_FABRIC_STOP, and drop local
reference in target_wait_for_sess_cmds() and invoke extra
target_put_sess_cmd() during Task Aborted Status (TAS)
when necessary.

Also, it adds a new target_wait_free_cmd() wrapper around
transport_wait_for_tasks() for the special case within
transport_generic_free_cmd() to set CMD_T_FABRIC_STOP,
and is now aware of CMD_T_ABORTED + CMD_T_TAS status
bits to know when an extra transport_put_cmd() during
TAS is required.

Note transport_generic_free_cmd() is expected to block on
cmd->cmd_wait_comp in order to follow what iscsi-target
expects during iscsi_conn context se_cmd shutdown.

Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

commit ebde1ca5 upstream.

This patch fixes a bug in TMR task aborted status (TAS)
handling when multiple sessions are connected to the
same target WWPN endpoint and se_node_acl descriptor,
resulting in TASK_ABORTED status to not be generated
for aborted se_cmds on the remote port.

This is due to core_tmr_handle_tas_abort() incorrectly
comparing se_node_acl instead of se_session, for which
the multi-session case is expected to be sharing the
same se_node_acl.

Instead, go ahead and update core_tmr_handle_tas_abort()
to compare tmr_sess + cmd->se_sess in order to determine
if the LUN_RESET was received on a different I_T nexus,
and TASK_ABORTED status response needs to be generated.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

commit febe562c upstream.

This patch fixes a NULL pointer se_cmd->cmd_kref < 0
refcount bug during TMR LUN_RESET with active se_cmd
I/O, that can be triggered during se_cmd descriptor
shutdown + release via core_tmr_drain_state_list() code.

To address this bug, add common __target_check_io_state()
helper for ABORT_TASK + LUN_RESET w/ CMD_T_COMPLETE
checking, and set CMD_T_ABORTED + obtain ->cmd_kref for
both cases ahead of last target_put_sess_cmd() after
TFO->aborted_task() -> transport_cmd_finish_abort()
callback has completed.

It also introduces SCF_ACK_KREF to determine when
transport_cmd_finish_abort() needs to drop the second
extra reference, ahead of calling target_put_sess_cmd()
for the final kref_put(&se_cmd->cmd_kref).

It also updates transport_cmd_check_stop() to avoid
holding se_cmd->t_state_lock while dropping se_cmd
device state via target_remove_from_state_list(), now
that core_tmr_drain_state_list() is holding the
se_device lock while checking se_cmd state from
within TMR logic.

Finally, move transport_put_cmd() release of SGL +
TMR + extended CDB memory into target_free_cmd_mem()
in order to avoid potential resource leaks in TMR
ABORT_TASK + LUN_RESET code-paths.  Also update
target_release_cmd_kref() accordingly.
Reviewed-by: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>