- 16 Mar, 2022 13 commits
-
-
MeiChia Chiu authored
The original single LDPC cap bit cannot be used to differentiate LDPC cap in each PHY mode. This modification split the single bit into 3 bits, ht_ldpc, vht_ldpc, and he_ldpc. Reviewed-by:
Ryder Lee <ryder.lee@mediatek.com> Suggested-by:
Money Wang <Money.Wang@mediatek.com> Signed-off-by:
MeiChia Chiu <MeiChia.Chiu@mediatek.com> Signed-off-by:
Felix Fietkau <nbd@nbd.name>
-
Evelyn Tsai authored
Driver needs to carry region definition when radar detection starts. Need to remap nl80211 DFS regions to chip region definition. Signed-off-by:
Evelyn Tsai <evelyn.tsai@mediatek.com> Signed-off-by:
Rubio Lu <Rubio-DW.Lu@mediatek.com> Signed-off-by:
-
Sean Wang authored
use mt76_hw instead of open coding it Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
-
Sean Wang authored
Properly set up the monitor mode the firmware can support to fix up RTS/CTS and beacon frames cannot be captured and forwarded to the host. Tested-by:
Deren Wu <deren.wu@mediatek.com> Tested-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
-
Lorenzo Bianconi authored
Introduce mt7663u_mcu_power_on utility routine since the code is shared between mt7663u_mcu_init() and mt7663u_probe(). Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Lorenzo Bianconi authored
Check return value of mt7615_mcu_restart routine in mt7663u_mcu_init(). Signed-off-by:
-
Ping-Ke Shih authored
smatch reports that: fw.c:1997 rtw89_append_probe_req_ie() error: uninitialized symbol 'ret'. This can be a issue only if no band is supported by the chip, but it is impossible. So, it is still safe without this patch. Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220311020007.20414-1-pkshih@realtek.com
-
Lukas Bulwahn authored
Commit dae0978d ("dt: bindings: net: add qcom,ath11k.yaml") obviously adds qcom,ath11k.yaml, but the file entry in MAINTAINERS, added with commit fcda1cb8 ("MAINTAINERS: add DT bindings files for ath10k and ath11k") then refers to qcom,ath11k.txt. Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a broken reference. Repair this file reference in QUALCOMM ATHEROS ATH11K WIRELESS DRIVER, and put it in alphabetic order while at it. Fixes: fcda1cb8 ("MAINTAINERS: add DT bindings files for ath10k and ath11k") Signed-off-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by:
-
Julia Lawall authored
Various spelling mistakes in comments. Detected with the help of Coccinelle. Signed-off-by:
Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by:
-
Julia Lawall authored
Various spelling mistakes in comments. Detected with the help of Coccinelle. Signed-off-by:
-
Jonathan Teh authored
This is an RTL8188CUS device, identifies as model N150MA-199WWS. Signed-off-by:
Jonathan Teh <jonathan.teh@outlook.com> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Julia Lawall authored
Use kzalloc instead of kmalloc + memset. The semantic patch that makes this change is: (https://coccinelle.gitlabpages.inria.fr/website/) //<smpl> @@ expression res, size, flag; @@ - res = kmalloc(size, flag); + res = kzalloc(size, flag); ... - memset(res, 0, size); //</smpl> Signed-off-by:
-
Colin Ian King authored
Don't populate the read-only array wmm_oui on the stack but instead make it static const. Also makes the object code a little smaller. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Signed-off-by:
-
- 15 Mar, 2022 4 commits
-
-
Lorenzo Bianconi authored
Update bssid_indicator in ieee80211_bss_conf according to the number of bssid in the set. Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
John Crispin authored
Trigger ieee80211_csa_finish() on the non-transmitting interfaces when channel switch concludes on the transmitting interface. Co-developed-by:
Aloka Dixit <alokad@codeaurora.org> Signed-off-by:
John Crispin <john@phrozen.org> Link: https://lore.kernel.org/r/6fde4d7f9fa387494f46a7aa4a584478dcda06f1.1645702516.git.lorenzo@kernel.orgSigned-off-by:
-
Lorenzo Bianconi authored
Add new fields in struct beacon_data to store all MBSSID elements. Generate a beacon template which includes all MBSSID elements. Move CSA offset to reflect the MBSSID element length. Co-developed-by:
-
Johannes Berg authored
When CONFIG_PM isn't defined we don't have the function ieee80211_sta_restart() compiled in, but we always need it now for firmware restart. Move it out of the ifdef. Fixes: 7d352ccf ("mac80211: Add support to trigger sta disconnect on hardware restart") Link: https://lore.kernel.org/r/20220312221957.1fa96c72db51.I8ecaa5f9402fede0272161e0531ab930b97fba3e@changeidSigned-off-by:
-
- 13 Mar, 2022 14 commits
-
-
David S. Miller authored
Merge tag 'linux-can-next-for-5.18-20220313' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next linux-can-next-for-5.18-20220313 Marc Kleine-Budde says: ==================== pull-request: can-next 2022-03-13 this is a pull request of 13 patches for net-next/master. The 1st patch is by me and fixes the freeing of a skb in the vxcan driver (initially added in this net-next window). The remaining 12 patches are also by me and target the mcp251xfd driver. The first patch fixes a printf modifier (initially added in this net-next window). The remaining patches add ethtool based ring and RX/TX IRQ coalescing support to the driver. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Marc Kleine-Budde authored
This patch increases the number of RX-FIFOs to 3 and the max TX-FIFO depth to 16. This leads to the following default ring configuration. CAN-2.0 mode: | FIFO setup: TEF: 0x400: 8*12 bytes = 96 bytes | FIFO setup: RX-0: FIFO 1/0x460: 32*20 bytes = 640 bytes | FIFO setup: RX-1: FIFO 2/0x6e0: 32*20 bytes = 640 bytes | FIFO setup: RX-2: FIFO 3/0x960: 16*20 bytes = 320 bytes | FIFO setup: TX: FIFO 4/0xaa0: 8*16 bytes = 128 bytes | FIFO setup: free: 224 bytes CAN-FD mode: | FIFO setup: TEF: 0x400: 4*12 bytes = 48 bytes | FIFO setup: RX-0: FIFO 1/0x430: 16*76 bytes = 1216 bytes | FIFO setup: RX-1: FIFO 2/0x8f0: 4*76 bytes = 304 bytes | FIFO setup: TX: FIFO 3/0xa20: 4*72 bytes = 288 bytes | FIFO setup: free: 192 bytes With the previously added ethtool ring configuration support the RAM on the chip can now be runtime configured between RX and TX buffers. Link: https://lore.kernel.org/20220313083640.501791-13-mkl@pengutronix.deSigned-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Marc Kleine-Budde authored
This patch adds support ethtool based configuration for the TX IRQ coalescing added in the previous patch. Link: https://lore.kernel.org/20220313083640.501791-12-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds TX IRQ coalescing support to the driver. The implemented algorithm is similar to the RX IRQ coalescing support added in the previous patch. Link: https://lore.kernel.org/20220313083640.501791-11-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds support ethtool based configuration for the RX IRQ coalescing added in the previous patch. Link: https://lore.kernel.org/20220313083640.501791-10-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds RX IRQ coalescing support to the driver. The mcp251xfd chip doesn't support proper hardware based coalescing, so this patch tries to implemented it in software. The RX-FIFO offers a "FIFO not empty" interrupt, which is used if no coalescing is active. With activated RX IRQ coalescing the "FIFO not empty" interrupt is disabled in the RX IRQ handler and the "FIFO half full" or "FIFO full interrupt" (depending on RX max coalesced frames IRQ) is used instead. To avoid RX CAN frame starvation a hrtimer is setup with RX coalesce usecs IRQ,on timer expiration the "FIFO not empty" is enabled again. Support for ethtool configuration is added in the next patch. Link: https://lore.kernel.org/20220313083640.501791-9-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds runtime configurable RX and TX ring parameters via ethtool to the driver. Link: https://lore.kernel.org/20220313083640.501791-8-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
So far the configuration of the hardware FIFOs is hard coded and depend only on the selected CAN mode (CAN-2.0 or CAN-FD). This patch updates the macros describing the ring, FIFO and RAM layout to prepare for the next patches that add support for runtime configurable ring parameters via ethtool. Link: https://lore.kernel.org/20220313083640.501791-7-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch prepares the driver for runtime configurable RX and TX ring parameters. The actual runtime config support will be added in the next patch. Link: https://lore.kernel.org/20220313083640.501791-6-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds basic ethtool support (to query the current and maximum ring parameters) to the driver. Link: https://lore.kernel.org/20220313083640.501791-5-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds support for coalescing to the RAM layout calculation. Link: https://lore.kernel.org/20220313083640.501791-4-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds a helper function to calculate the ring configuration of the controller based on various constraints, like available RAM, size of RX and TX objects, CAN-mode, number of FIFOs and FIFO depth. Link: https://lore.kernel.org/20220313083640.501791-3-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
In case of an erroneous ring configuration more RAM than available might be used. Change the printf modifier to a signed int to properly print this erroneous value. Fixes: 83daa863 ("can: mcp251xfd: ring: update FIFO setup debug info") Link: https://lore.kernel.org/20220313083640.501791-2-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch fixes the freeing of the "oskb", by using kfree_skb() instead of kfree(). Fixes: 1574481b ("vxcan: remove sk reference in peer skb") Link: https://lore.kernel.org/all/20220311123741.382618-1-mkl@pengutronix.de Cc: Oliver Hartkopp <socketcan@hartkopp.net> Reported-by:
kernel test robot <lkp@intel.com> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
- 12 Mar, 2022 9 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueDavid S. Miller authored
Tony Nguyen says: ==================== ice: GTP support in switchdev Marcin Szycik says: Add support for adding GTP-C and GTP-U filters in switchdev mode. To create a filter for GTP, create a GTP-type netdev with ip tool, enable hardware offload, add qdisc and add a filter in tc: ip link add $GTP0 type gtp role <sgsn/ggsn> hsize <hsize> ethtool -K $PF0 hw-tc-offload on tc qdisc add dev $GTP0 ingress tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \ action mirred egress redirect dev $VF1_PR By default, a filter for GTP-U will be added. To add a filter for GTP-C, specify enc_dst_port = 2123, e.g.: tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \ enc_dst_port 2123 action mirred egress redirect dev $VF1_PR Note: outer IPv6 offload is not supported yet. Note: GTP-U with no payload offload is not supported yet. ICE COMMS package is required to create a filter as it contains GTP profiles. Changes in iproute2 [1] are required to be able to add GTP netdev and use GTP-specific options (QFI and PDU type). [1] https://lore.kernel.org/netdev/20220211182902.11542-1-wojciech.drewek@intel.com/T --- v2: Add more CC v3: Fix mail thread, sorry for spam v4: Add GTP echo response in gtp module v5: Change patch order v6: Add GTP echo request in gtp module v7: Fix kernel-docs in ice v8: Remove handling of GTP Echo Response v9: Add sending of multicast message on GTP Echo Response, fix GTP-C dummy packet selection v10: Rebase, fixed most 80 char line limits v11: Rebase, collect Harald's Reviewed-by on patch 3 ==================== Signed-off-by:
-
Oleksij Rempel authored
In case external PHY is used, we need to take care of embedded PHY. Since there are no methods to disable this PHY from the MAC side and keeping RMII reference clock, we need to suspend it. This patch will reduce electrical noise (PHY is continuing to send FLPs) and power consumption by 0,22W. Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
-
Oleksij Rempel authored
In most cases we use own mdio bus, there is no need to create and store string for the PHY address. Signed-off-by:
-
Oleksij Rempel authored
We already read chipid on probe. There is no need to read it on reset. Signed-off-by:
-
Oleksij Rempel authored
The only difference is the reset code, so remove not needed duplicates. Signed-off-by:
-
Eric Dumazet authored
Before adding yet another possibly contended atomic_long_t, it is time to add per-cpu storage for existing ones: dev->tx_dropped, dev->rx_dropped, and dev->rx_nohandler Because many devices do not have to increment such counters, allocate the per-cpu storage on demand, so that dev_get_stats() does not have to spend considerable time folding zero counters. Note that some drivers have abused these counters which were supposed to be only used by core networking stack. v4: should use per_cpu_ptr() in dev_get_stats() (Jakub) v3: added a READ_ONCE() in netdev_core_stats_alloc() (Paolo) v2: add a missing include (reported by kernel test robot <lkp@intel.com>) Change in netdev_core_stats_alloc() (Jakub) Signed-off-by:Eric Dumazet <edumazet@google.com> Cc: jeffreyji <jeffreyji@google.com> Reviewed-by:
Brian Vazquez <brianvv@google.com> Reviewed-by:
Jakub Kicinski <kuba@kernel.org> Acked-by:
Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20220311051420.2608812-1-eric.dumazet@gmail.comSigned-off-by:
-
Jakub Kicinski authored
Simon Horman says: ==================== nfp: preliminary support for NFP-3800 This series is the first step to add support to the NFP driver for the new NFP-3800 device. In this first series the goal is to clean up small issues found while adding support for the new device, prepare an abstraction of the differences between the already supported devices and the new Kestrel device and add the new PCI ID. * Patch 1/11 and 2/11 starts by removing some dead code and incorrect assumptions found while working Kestrel support. Patch 3/11, 4/11 and 5/11 cleans up and prepares for adding the new PCI ID for Kestrel. * Patches 6/11, 7/11, 8/11, 9/11, 10/11 adds, plumb and populates a device information structure to abstract the differences between the existed supported devices (NFP-4000, NFP-5000 and NFP-6000) and the new device (NFP3800). * Finally patch 11/11 adds the new PCI ID for Kestrel. More work is needed to drive the new NFP-3800 device after this first batch of patches the foundation is prepared for the follow up work. Thanks to the work of all those who contributed to this work. ==================== Link: https://lore.kernel.org/r/20220311104306.28357-1-simon.horman@corigine.comSigned-off-by:
-
Dirk van der Merwe authored
Enable binding the nfp driver to NFP3800 and NFP3803 devices. The PCIE_SRAM offset is different for the NFP3800 device, which also only supports a single explicit group. Changes to Dirk's work: * 48-bit dma addressing is not ready yet. Keep 40-bit dma addressing for NFP3800. Signed-off-by:
Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
Fei Qin <fei.qin@corigine.com> Signed-off-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Jakub Kicinski authored
NFP3800 has slightly different queue controller range bounds. Use the static chip data instead of defines. This commit still assumes unchanged descriptor format. Later datapath changes will allow adjusting for descriptor accounting. Signed-off-by:
-
