- 23 Dec, 2023 19 commits
-
-
Roger Quadros authored
Add driver support for viewing / changing the MAC Merge sublayer parameters and seeing the verification state machine's current state via ethtool. As hardware does not support interrupt notification for verification events we resort to polling on link up. On link up we try a couple of times for verification success and if unsuccessful then give up. The Frame Preemption feature is described in the Technical Reference Manual [1] in section: 12.3.1.4.6.7 Intersperced Express Traffic (IET – P802.3br/D2.0) Due to Silicon Errata i2208 [2] we set limit min IET fragment size to 124 (excluding 4 bytes mCRC). [1] AM62x TRM - https://www.ti.com/lit/ug/spruiv7a/spruiv7a.pdf [2] AM62x Silicon Errata - https://www.ti.com/lit/er/sprz487c/sprz487c.pdfSigned-off-by:
Roger Quadros <rogerq@kernel.org> Reviewed-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Grygorii Strashko authored
This patch adds MQPRIO Qdisc offload in full 'channel' mode which allows not only setting up pri:tc mapping, but also configuring TX shapers (rate-limiting) on external port FIFOs. The MQPRIO Qdisc offload is expected to work with or without VLAN/priority tagged packets. The CPSW external Port FIFO has 8 Priority queues. The rate-limit can be set for each of these priority queues. Which Priority queue a packet is assigned to depends on PN_REG_TX_PRI_MAP register which maps header priority to switch priority. The header priority of a packet is assigned via the RX_PRI_MAP_REG which maps packet priority to header priority. The packet priority is either the VLAN priority (for VLAN tagged packets) or the thread/channel offset. For simplicity, we assign the same priority queue to all queues of a Traffic Class so it can be rate-limited correctly. Configuration example: ethtool -L eth1 tx 5 ethtool --set-priv-flags eth1 p0-rx-ptype-rrobin off tc qdisc add dev eth1 parent root handle 100: mqprio num_tc 3 \ map 0 0 1 2 0 0 0 0 0 0 0 0 0 0 0 0 \ queues 1@0 1@1 1@2 hw 1 mode channel \ shaper bw_rlimit min_rate 0 100mbit 200mbit max_rate 0 101mbit 202mbit tc qdisc replace dev eth2 handle 100: parent root mqprio num_tc 1 \ map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 queues 1@0 hw 1 ip link add link eth1 name eth1.100 type vlan id 100 ip link set eth1.100 type vlan egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 In the above example two ports share the same TX CPPI queue 0 for low priority traffic. 3 traffic classes are defined for eth1 and mapped to: TC0 - low priority, TX CPPI queue 0 -> ext Port 1 fifo0, no rate limit TC1 - prio 2, TX CPPI queue 1 -> ext Port 1 fifo1, CIR=100Mbit/s, EIR=1Mbit/s TC2 - prio 3, TX CPPI queue 2 -> ext Port 1 fifo2, CIR=200Mbit/s, EIR=2Mbit/s Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
-
Roger Quadros authored
Move register definitions to header file. No functional change. Signed-off-by:
-
Roger Quadros authored
Move this code around to avoid forward declaration. No functional change. Signed-off-by:
-
Roger Quadros authored
Handle offloading commands using switch-case in am65_cpsw_setup_taprio(). Move checks to am65_cpsw_taprio_replace(). Use NL_SET_ERR_MSG_MOD for error messages. Change error message from "Failed to set cycle time extension" to "cycle time extension not supported" Signed-off-by:
-
Roger Quadros authored
We will use this Kconfig option to not only enable TAS/EST offload but also other QoS features like Multiqueue priority descriptors and MAC-Merge/Frame Preemption. TI_AM65_CPSW_QOS seems a more appropriate Kconfig option name than TI_AM65_CPSW_TAS. Signed-off-by:
-
Roger Quadros authored
Build am65-cpsw-qos only if CONFIG_TI_AM65_CPSW_TAS is enabled. Signed-off-by:
-
Vladimir Oltean authored
Some devices do not support individual 'pmac' and 'emac' stats. For such devices, resort to 'aggregate' stats. Cc: Shuah Khan <shuah@kernel.org> Signed-off-by:
-
Vladimir Oltean authored
Some devices have errata due to which they cannot report ETH_ZLEN (60) in the rx-min-frag-size. This was foreseen of course, and lldpad has logic that when we request it to advertise addFragSize 0, it will round it up to the lowest value that is _actually_ supported by the hardware. The problem is that the selftest expects lldpad to report back to us the same value as we requested. Make the selftest smarter by figuring out on its own what is a reasonable value to expect. Cc: Shuah Khan <shuah@kernel.org> Signed-off-by:
-
David S. Miller authored
Hangbin Liu says: ==================== Convert net selftests to run in unique namespace (last part) Here is the last part of converting net selftests to run in unique namespace. This part converts all left tests. After the conversion, we can run the net sleftests in parallel. e.g. # ./run_kselftest.sh -n -t net:reuseport_bpf TAP version 13 1..1 # selftests: net: reuseport_bpf ok 1 selftests: net: reuseport_bpf mod 10... # Socket 0: 0 # Socket 1: 1 ... # Socket 4: 19 # Testing filter add without bind... # SUCCESS # ./run_kselftest.sh -p -n -t net:cmsg_so_mark.sh -t net:cmsg_time.sh -t net:cmsg_ipv6.sh TAP version 13 1..3 # selftests: net: cmsg_so_mark.sh ok 1 selftests: net: cmsg_so_mark.sh # selftests: net: cmsg_time.sh ok 2 selftests: net: cmsg_time.sh # selftests: net: cmsg_ipv6.sh ok 3 selftests: net: cmsg_ipv6.sh # ./run_kselftest.sh -p -n -c net TAP version 13 1..95 # selftests: net: reuseport_bpf_numa ok 3 selftests: net: reuseport_bpf_numa # selftests: net: reuseport_bpf_cpu ok 2 selftests: net: reuseport_bpf_cpu # selftests: net: sk_bind_sendto_listen ok 9 selftests: net: sk_bind_sendto_listen # selftests: net: reuseaddr_conflict ok 5 selftests: net: reuseaddr_conflict ... Here is the part 1 link: https://lore.kernel.org/netdev/20231202020110.362433-1-liuhangbin@gmail.com part 2 link: https://lore.kernel.org/netdev/20231206070801.1691247-1-liuhangbin@gmail.com part 3 link: https://lore.kernel.org/netdev/20231213060856.4030084-1-liuhangbin@gmail.com ==================== Signed-off-by:
-
Hangbin Liu authored
Add a variable RUN_IN_NETNS if the user wants to run all the selected tests in namespace in parallel. With this, we can save a lot of testing time. Note that some tests may not fit to run in namespace, e.g. net/drop_monitor_tests.sh, as the dwdump needs to be run in init ns. I also added another parameter -p to make all the logs reported separately instead of mixing them in the stdout or output.log. Nit: the NUM in run_one is not used, rename it to test_num. Acked-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Signed-off-by:
-
Hangbin Liu authored
pmtu test use /bin/sh, so we need to source ./lib.sh instead of lib.sh Here is the test result after conversion. # ./pmtu.sh TEST: ipv4: PMTU exceptions [ OK ] TEST: ipv4: PMTU exceptions - nexthop objects [ OK ] TEST: ipv6: PMTU exceptions [ OK ] TEST: ipv6: PMTU exceptions - nexthop objects [ OK ] ... TEST: ipv4: list and flush cached exceptions - nexthop objects [ OK ] TEST: ipv6: list and flush cached exceptions [ OK ] TEST: ipv6: list and flush cached exceptions - nexthop objects [ OK ] TEST: ipv4: PMTU exception w/route replace [ OK ] TEST: ipv4: PMTU exception w/route replace - nexthop objects [ OK ] TEST: ipv6: PMTU exception w/route replace [ OK ] TEST: ipv6: PMTU exception w/route replace - nexthop objects [ OK ] Signed-off-by:
-
Hangbin Liu authored
The setup_loopback and setup_veth use their own way to create namespace. So let's just re-define server_ns/client_ns to unique name. At the same time update the namespace name in gro.sh and toeplitz.sh. As I don't have env to run toeplitz.sh. Here is only the gro test result. # ./gro.sh running test ipv4 data Expected {200 }, Total 1 packets Received {200 }, Total 1 packets. ... Gro::large test passed. All Tests Succeeded! Acked-by: -
Hangbin Liu authored
Here is the test result after conversion. # ./xfrm_policy.sh PASS: policy before exception matches PASS: ping to .254 bypassed ipsec tunnel (exceptions) PASS: direct policy matches (exceptions) PASS: policy matches (exceptions) PASS: ping to .254 bypassed ipsec tunnel (exceptions and block policies) PASS: direct policy matches (exceptions and block policies) PASS: policy matches (exceptions and block policies) PASS: ping to .254 bypassed ipsec tunnel (exceptions and block policies after hresh changes) PASS: direct policy matches (exceptions and block policies after hresh changes) PASS: policy matches (exceptions and block policies after hresh changes) PASS: ping to .254 bypassed ipsec tunnel (exceptions and block policies after hthresh change in ns3) PASS: direct policy matches (exceptions and block policies after hthresh change in ns3) PASS: policy matches (exceptions and block policies after hthresh change in ns3) PASS: ping to .254 bypassed ipsec tunnel (exceptions and block policies after htresh change to normal) PASS: direct policy matches (exceptions and block policies after htresh change to normal) PASS: policy matches (exceptions and block policies after htresh change to normal) PASS: policies with repeated htresh change Acked-by:
-
Hangbin Liu authored
Here is the test result after conversion. # ./stress_reuseport_listen.sh listen 24000 socks took 0.47714 Acked-by:
-
Hangbin Liu authored
When running the test in namespace, the debugfs may not load automatically. So add a checking to make sure debugfs loaded. Here is the test result after conversion. # ./rtnetlink.sh PASS: policy routing PASS: route get ... PASS: address proto IPv4 PASS: address proto IPv6 Acked-by:
-
Hangbin Liu authored
This test will move the device to netns 1. Add a new test_ns to do this. Here is the test result after conversion. # ./netns-name.sh netns-name.sh [ OK ] Acked-by:
-
Hangbin Liu authored
Here is the test result after conversion. # ./gre_gso.sh TEST: GREv6/v4 - copy file w/ TSO [ OK ] TEST: GREv6/v4 - copy file w/ GSO [ OK ] TEST: GREv6/v6 - copy file w/ TSO [ OK ] TEST: GREv6/v6 - copy file w/ GSO [ OK ] Tests passed: 4 Tests failed: 0 Acked-by: -
Jiapeng Chong authored
No functional modification involved. ./tools/testing/selftests/net/tcp_ao/setsockopt-closed.c:121:2-3: Unneeded semicolon. Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=7771Signed-off-by:
Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by:
-
- 22 Dec, 2023 19 commits
-
-
Dmitry Safonov authored
Trivial fix for out-of-tree build that I wasn't testing previously: 1. Create a directory for library object files, fixes: > gcc lib/kconfig.c -Wall -O2 -g -D_GNU_SOURCE -fno-strict-aliasing -I ../../../../../usr/include/ -iquote /tmp/kselftest/kselftest/net/tcp_ao/lib -I ../../../../include/ -o /tmp/kselftest/kselftest/net/tcp_ao/lib/kconfig.o -c > Assembler messages: > Fatal error: can't create /tmp/kselftest/kselftest/net/tcp_ao/lib/kconfig.o: No such file or directory > make[1]: *** [Makefile:46: /tmp/kselftest/kselftest/net/tcp_ao/lib/kconfig.o] Error 1 2. Include $(KHDR_INCLUDES) that's exported by selftests/Makefile, fixes: > In file included from lib/kconfig.c:6: > lib/aolib.h:320:45: warning: ‘struct tcp_ao_add’ declared inside parameter list will not be visible outside of this definition or declaration > 320 | extern int test_prepare_key_sockaddr(struct tcp_ao_add *ao, const char *alg, > | ^~~~~~~~~~ ... 3. While at here, clean-up $(KSFT_KHDR_INSTALL): it's not needed anymore since commit f2745dc0 ("selftests: stop using KSFT_KHDR_INSTALL") 4. Also, while at here, drop .DEFAULT_GOAL definition: that has a self-explaining comment, that was valid when I made these selftests compile on local v4.19 kernel, but not needed since commit 8ce72dc3 ("selftests: fix headers_install circular dependency") Fixes: cfbab37b ("selftests/net: Add TCP-AO library") Reported-by:
kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202312190645.q76MmHyq-lkp@intel.com/Signed-off-by:
Dmitry Safonov <dima@arista.com> Signed-off-by:
-
Jonathan Corbet authored
Remove documentation for nonexistent struct members, addressing these warnings: ./net/tipc/link.c:228: warning: Excess struct member 'media_addr' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'timer' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'refcnt' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'proto_msg' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'pmsg' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'backlog_limit' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'exp_msg_count' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'reset_rcv_checkpt' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'transmitq' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'snt_nxt' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'deferred_queue' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'unacked_window' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'next_out' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'long_msg_seq_no' description in 'tipc_link' ./net/tipc/link.c:228: warning: Excess struct member 'bc_rcvr' description in 'tipc_link' Signed-off-by:
Jonathan Corbet <corbet@lwn.net> Reviewed-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
Jonathan Corbet authored
Remove documentation for nonexistent structure members, addressing these warnings: ./include/linux/skbuff.h:1063: warning: Excess struct member 'sp' description in 'sk_buff' ./include/linux/skbuff.h:1063: warning: Excess struct member 'nf_bridge' description in 'sk_buff' Signed-off-by:
-
David S. Miller authored
Kuniyuki Iwashima says: ==================== tcp: Refactor bhash2 and remove sk_bind2_node. This series refactors code around bhash2 and remove some bhash2-specific fields; sock.sk_bind2_node, and inet_timewait_sock.tw_bind2_node. patch 1 : optimise bind() for non-wildcard v4-mapped-v6 address patch 2 - 4 : optimise bind() conflict tests patch 5 - 12 : Link bhash2 to bhash and unlink sk from bhash2 to remove sk_bind2_node The patch 8 will trigger a false-positive error by checkpatch. v2: resend of https://lore.kernel.org/netdev/20231213082029.35149-1-kuniyu@amazon.com/ * Rebase on latest net-next * Patch 11 * Add change in inet_diag_dump_icsk() for recent bhash dump patch v1: https://lore.kernel.org/netdev/20231023190255.39190-1-kuniyu@amazon.com/ ==================== Signed-off-by: -
Kuniyuki Iwashima authored
Now all sockets including TIME_WAIT are linked to bhash2 using sock_common.skc_bind_node. We no longer use inet_bind2_bucket.deathrow, sock.sk_bind2_node, and inet_timewait_sock.tw_bind2_node. Signed-off-by:
Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Kuniyuki Iwashima authored
Now we can use sk_bind_node/tw_bind_node for bhash2, which means we need not link TIME_WAIT sockets separately. The dead code and sk_bind2_node will be removed in the next patch. Signed-off-by:
-
Kuniyuki Iwashima authored
Now we do not use tb->owners and can unlink sockets from bhash. sk_bind_node/tw_bind_node are available for bhash2 and will be used in the following patch. Signed-off-by:
-
Kuniyuki Iwashima authored
We use hlist_empty(&tb->owners) to check if the bhash bucket has a socket. We can check the child bhash2 buckets instead. For this to work, the bhash2 bucket must be freed before the bhash bucket. Signed-off-by:
-
Kuniyuki Iwashima authored
Sockets in bhash are also linked to bhash2, but TIME_WAIT sockets are linked separately in tb2->deathrow. Let's replace tb->owners iteration in inet_csk_bind_conflict() with two iterations over tb2->owners and tb2->deathrow. This can be done safely under bhash's lock because socket insertion/ deletion in bhash2 happens with bhash's lock held. Note that twsk_for_each_bound_bhash() will be removed later. Signed-off-by:
-
Kuniyuki Iwashima authored
The following patch adds code in the !inet_use_bhash2_on_bind(sk) case in inet_csk_bind_conflict(). To avoid adding nest and make the change cleaner, this patch rearranges tests in inet_csk_bind_conflict(). Signed-off-by:
-
Kuniyuki Iwashima authored
bhash2 added a new member sk_bind2_node in struct sock to link sockets to bhash2 in addition to bhash. bhash is still needed to search conflicting sockets efficiently from a port for the wildcard address. However, bhash itself need not have sockets. If we link each bhash2 bucket to the corresponding bhash bucket, we can iterate the same set of the sockets from bhash2 via bhash. This patch links bhash2 to bhash only, and the actual use will be in the later patches. Finally, we will remove sk_bind2_node. Signed-off-by:
-
Kuniyuki Iwashima authored
Later, we no longer link sockets to bhash. Instead, each bhash2 bucket is linked to the corresponding bhash bucket. Then, we pass the bhash bucket to bhash2 allocation functions as tb. However, tb is already used in inet_bind2_bucket_create() and inet_bind2_bucket_init() as the bhash2 bucket. To make the following diff clear, let's use tb2 for the bhash2 bucket there. Signed-off-by:
-
Kuniyuki Iwashima authored
inet_bind2_bucket_addr_match() and inet_bind2_bucket_match_addr_any() are called for each bhash2 bucket to check conflicts. Thus, we call ipv6_addr_any() and ipv6_addr_v4mapped() over and over during bind(). Let's avoid calling them by saving the address type in inet_bind2_bucket. Signed-off-by:
-
Kuniyuki Iwashima authored
In bhash2, IPv4/IPv6 addresses are saved in two union members, which complicate address checks in inet_bind2_bucket_addr_match() and inet_bind2_bucket_match_addr_any() considering uninitialised memory and v4-mapped-v6 conflicts. Let's simplify that by saving IPv4 address as v4-mapped-v6 address and defining tb2.rcv_saddr as tb2.v6_rcv_saddr.s6_addr32[3]. Then, we can compare v6 address as is, and after checking v4-mapped-v6, we can compare v4 address easily. Also, we can remove tb2->family. Note these functions will be further refactored in the next patch. Signed-off-by:
-
Kuniyuki Iwashima authored
The protocol family tests in inet_bind2_bucket_addr_match() and inet_bind2_bucket_match_addr_any() are ordered as follows. if (sk->sk_family != tb2->family) else if (sk->sk_family == AF_INET6) else This patch rearranges them so that AF_INET6 socket is handled first to make the following patch tidy, where tb2->family will be removed. if (sk->sk_family == AF_INET6) else if (tb2->family == AF_INET6) else Signed-off-by:
-
Kuniyuki Iwashima authored
While checking port availability in bind() or listen(), we used only bhash for all v4-mapped-v6 addresses. But there is no good reason not to use bhash2 for v4-mapped-v6 non-wildcard addresses. Let's do it by returning true in inet_use_bhash2_on_bind(). Then, we also need to add a test in inet_bind2_bucket_match_addr_any() so that ::ffff:X.X.X.X will match with 0.0.0.0. Note that sk->sk_rcv_saddr is initialised for v4-mapped-v6 sk in __inet6_bind(). Signed-off-by:
-
Colin Ian King authored
There are a handful of spelling mistakes in test messages in the TCP-AIO selftests. Fix these. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Reviewed-by:
-
Suman Ghosh authored
There was a memory leak during error handling in function npc_mcam_rsrcs_init(). Fixes: dd784287 ("octeontx2-af: Add new devlink param to configure maximum usable NIX block LFs") Suggested-by:
Simon Horman <horms@kernel.org> Signed-off-by:
Suman Ghosh <sumang@marvell.com> Reviewed-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueDavid S. Miller authored
Tony Nguyen says: ==================== intel: use bitfield operations Jesse Brandeburg says: After repeatedly getting review comments on new patches, and sporadic patches to fix parts of our drivers, we should just convert the Intel code to use FIELD_PREP() and FIELD_GET(). It's then "common" in the code and hopefully future change-sets will see the context and do-the-right-thing. This conversion was done with a coccinelle script which is mentioned in the commit messages. Generally there were only a couple conversions that were "undone" after the automatic changes because they tried to convert a non-contiguous mask. Patch 1 is required at the beginning of this series to fix a "forever" issue in the e1000e driver that fails the compilation test after conversion because the shift / mask was out of range. The second patch just adds all the new #includes in one go. The patch titled: "ice: fix pre-shifted bit usage" is needed to allow the use of the FIELD_* macros and fix up the unexpected "shifts included" defines found while creating this series. The rest are the conversion to use FIELD_PREP()/FIELD_GET(), and the occasional leXX_{get,set,encode}_bits() call, as suggested by Alex. ==================== Signed-off-by:
-
- 21 Dec, 2023 2 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netPaolo Abeni authored
Cross-merge networking fixes after downstream PR. Adjacent changes: drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c 23c93c3b ("bnxt_en: do not map packet buffers twice") 6d1add95 ("bnxt_en: Modify TX ring indexing logic.") tools/testing/selftests/net/Makefile 2258b666 ("selftests: add vlan hw filter tests") a0bc96c0 ("selftests: net: verify fq per-band packet limit") Signed-off-by:
Paolo Abeni <pabeni@redhat.com>
-
David Ahern authored
A revert of 3dec89b1 ("net/ipv6: Remove expired routes with a separated list of routes") was sent for net-next. Revert the remainder of 5a08d006 which added a warn on if a fib entry is still on the gc_link list to avoid compile failures when net is merged to net-next Signed-off-by:
-
