Current .n_voltages settings do not cover the latest 2 valid selectors,
so it fails to set voltage for the hightest voltage support.
The latest linear range has step_uV = 0, so it does not matter if we
count the .n_voltages to maximum selector + 1 or the first selector of
latest linear range + 1.
To simplify calculating the n_voltages, let's just set the
.n_voltages to maximum selector + 1.

Fixes: 522498f8 ("regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210523071045.2168904-2-axel.lin@ingics.comSigned-off-by: Mark Brown <broonie@kernel.org>

The valid selectors for bd70528 bucks are 0 ~ 0xf, so the .n_voltages
should be 16 (0x10). Use 0x10 to make it consistent with BD70528_LDO_VOLTS.
Also remove redundant defines for BD70528_BUCK_VOLTS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210523071045.2168904-1-axel.lin@ingics.comSigned-off-by: Mark Brown <broonie@kernel.org>

For linear regulators, the .n_voltages is (max_uv - min_uv) / uv_step + 1.

Fixes: 0fbeae70 ("regulator: add SCMI driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20210521073020.1944981-1-axel.lin@ingics.comSigned-off-by: Mark Brown <broonie@kernel.org>

For the boot-on/always-on regulators the set_machine_constrainst() is
called before resolving rdev->supply. Thus the code would try to enable
rdev before enabling supplying regulator. Enforce resolving supply
regulator before enabling rdev.

Fixes: aea6cb99 ("regulator: resolve supply after creating regulator")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210519221224.2868496-1-dmitry.baryshkov@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

dev_pm_genpd_set_performance_state() may fail, so had better to check it's
return value before decreasing priv->enable_counter.

Fixes: bf3a28cf ("regulator: fixed: support using power domain for enable/disable")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210520111811.1806293-1-axel.lin@ingics.comSigned-off-by: Mark Brown <broonie@kernel.org>

Return -EINVAL if ramp_delay_table is NULL.
Also add WARN_ON since the driver code needs fix if this happened.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210519132255.1683863-1-axel.lin@ingics.comSigned-off-by: Mark Brown <broonie@kernel.org>

Fixes: e6dea51e ("regulator: fan53880: Add initial support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Christoph Fritz <chf.fritz@googlemail.com>
Link: https://lore.kernel.org/r/20210517105325.1227393-1-axel.lin@ingics.comSigned-off-by: Mark Brown <broonie@kernel.org>

-EINVAL is not a valid return value for .of_map_mode, return
REGULATOR_MODE_INVALID instead.

Fixes: 65ac9704 ("regulator: da9121: add mode support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/20210517052721.1063375-1-axel.lin@ingics.comSigned-off-by: Mark Brown <broonie@kernel.org>

The tcs4525 voltage calculation is incorrect, which leads to a deadlock
on the rk3566-quartz64 board when loading cpufreq.
Fix the voltage calculation to correct the deadlock.
While we are at it, add a safety check and clean up the function names
to be more accurate.

Peter Geis (3):
  regulator: fan53555: fix TCS4525 voltage calulation
  regulator: fan53555: only bind tcs4525 to correct chip id
  regulator: fan53555: fix tcs4525 function names

 drivers/regulator/fan53555.c | 44 ++++++++++++++++++++++--------------
 1 file changed, 27 insertions(+), 17 deletions(-)

--
2.25.1

The TCS4525 has 128 voltage steps. With the calculation set to 127 the
most significant bit is disregarded which leads to a miscalculation of
the voltage by about 200mv.

Fix the calculation to end deadlock on the rk3566-quartz64 which uses
this as the cpu regulator.

Fixes: 914df8fa ("regulator: fan53555: Add TCS4525 DCDC support")
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20210511211335.2935163-2-pgwipeout@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Show proper error code instead of 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210512075824.620580-1-axel.lin@ingics.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add a compatible string to support TCS4525/TCS4526 devices,
which are compatible with Fairchild FAN53555 regulators.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20210421210338.43819-2-ezequiel@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

TCS4525 main features:

- 2.7V to 5.5V Input Voltage Range;
- 3MHz Constant Switching Frequency;
- 5A Available Load Current;
- Programmable Output Voltage: 0.6V to 1.4V in 6.25mV Steps;
- PFM/PWM Operation for Optimum Increased Efficiency;
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[Ezequiel: Forward port]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20210421210338.43819-3-ezequiel@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

Shenzhen City Tang Cheng Technology (http://www.tctek.cn/)
is a power management IC manufacturer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20210421210338.43819-1-ezequiel@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

The jiffies-based off_on_delay implementation has a couple of problems
that cause it to sometimes not actually delay for the required time:

 (1) If, for example, the off_on_delay time is equivalent to one jiffy,
     and the ->last_off_jiffy is set just before a new jiffy starts,
     then _regulator_do_enable() does not wait at all since it checks
     using time_before().

 (2) When jiffies overflows, the value of "remaining" becomes higher
     than "max_delay" and the code simply proceeds without waiting.

Fix these problems by changing it to use ktime_t instead.

[Note that since jiffies doesn't start at zero but at INITIAL_JIFFIES
 ("-5 minutes"), (2) above also led to the code not delaying if
 the first regulator_enable() is called when the ->last_off_jiffy is not
 initialised, such as for regulators with ->constraints->boot_on set.
 It's not clear to me if this was intended or not, but I've preserved
 this behaviour explicitly with the check for a non-zero ->last_off.]
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20210423114524.26414-1-vincent.whitchurch@axis.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'for-5.12' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-5.13

We currently do not respect off_on_delay the first time we turn on a
regulator.  This is problematic since the regulator could have been
turned off by the bootloader, or it could it have been turned off during
the probe of the regulator driver (such as when regulator-fixed requests
the enable GPIO), either of which could potentially have happened less
than off_on_delay microseconds ago before the first time a client
requests for the regulator to be turned on.

We can't know exactly when the regulator was turned off, but initialise
off_on_delay to the current time when registering the regulator, so that
we guarantee that we respect the off_on_delay in all cases.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20210422083044.11479-1-vincent.whitchurch@axis.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series "mfd/rtc/regulator: Drop board file support for Samsung PMIC" from Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>:

Hi,

The Samsung PMIC drivers since long time are used only on devicetree
platforms (Samsung Exynos) and there are no users with board files.

Drop the support for board files entirely and depend on OF for matching.

This makes the code smaller and simpler.

Dependencies
============
The MFD pieces are rebased on my previous sec-core dirver changes:
mfd: sec: Simplify getting of_device_id match data
https://lore.kernel.org/linux-samsung-soc/20210420113929.278082-1-krzysztof.kozlowski@canonical.com/T/#t

Applying - can be independent
=============================
The last RTC and regulator patches can be picked up independently via
regulator and rtc trees.  There are no board files currently, so the
code in these drivers is basically dead code and feature-bisection is
preserved.

Best regards,
Krzysztof

Krzysztof Kozlowski (9):
  mfd: sec: Drop support for board files and require devicetree
  mfd: sec: Remove unused cfg_pmic_irq in platform data
  mfd: sec: Remove unused device_type in platform data
  mfd: sec: Remove unused irq_base in platform data
  mfd: sec: Enable wakeup from suspend via devicetree property
  mfd: sec: Remove unused platform data members
  rtc: s5m: Remove reference to parent's device pdata
  regulator: s2mpa01: Drop initialization via platform data
  regulator: s2mps11: Drop initialization via platform data

 drivers/mfd/Kconfig              |  1 +
 drivers/mfd/sec-core.c           | 64 +++++---------------------------
 drivers/mfd/sec-irq.c            |  4 +-
 drivers/regulator/s2mpa01.c      |  4 --
 drivers/regulator/s2mps11.c      | 22 +----------
 drivers/rtc/rtc-s5m.c            |  6 ---
 include/linux/mfd/samsung/core.h | 33 ----------------
 7 files changed, 14 insertions(+), 120 deletions(-)

--
2.25.1

s/regulator may on/regulator may already be enabled/
s/or left on/or was left on/

The aim of this patch is to make the comment more readable and to make
it clear, that this is about a regulator, that is already enabled instead
of a regulator that may be switched on.
Signed-off-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Link: https://lore.kernel.org/r/20210421055236.13148-1-sebastian.fricke@posteo.netSigned-off-by: Mark Brown <broonie@kernel.org>

'for_each_available_child_of_node()' already performs an 'of_node_get()'
on child, so there is no need to perform another one before returning.
Otherwise, a double 'get' is performed and a resource may never be
released.

Fixes: 925c85e2 ("regulator: Factor out location of init data OF node")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/a79f0068812b89ff412d572a1171f22109c24132.1618947049.git.christophe.jaillet@wanadoo.frSigned-off-by: Mark Brown <broonie@kernel.org>

Shifted the closing */ of multiline comment to a new line
This is done to maintain code uniformity
Signed-off-by: Shubhankar Kuranagatti <shubhankarvk@gmail.com>
Link: https://lore.kernel.org/r/20210420034718.t7wudu6xcfpahflv@kewl-virtual-machineSigned-off-by: Mark Brown <broonie@kernel.org>

None of the platforms with S2MPS11 use board files, so any
initialization via platform data can be safely removed.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210420170244.13467-5-krzysztof.kozlowski@canonical.comSigned-off-by: Mark Brown <broonie@kernel.org>

None of the platforms with S2MPA01 use board files, so any
initialization via platform data can be safely removed.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210420170244.13467-4-krzysztof.kozlowski@canonical.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch fixes identification of DA913x parts by the DA9121 driver,
where a lack of clarity lead to implementation on the basis that variant
IDs were to be identical to the equivalent rated non-automotive parts.

There is a new emphasis on the DT identity to cope with overlap in these
ID's - this is not considered to be problematic, because projects would
be exclusively using automotive or consumer grade parts.
Signed-off-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/20210421120306.DB5B880007F@slsrvapps-01.diasemi.comSigned-off-by: Mark Brown <broonie@kernel.org>

Patch series introducing support for ROHM BD71815 PMIC

ROHM BD71815 is a power management IC used in some battery powered
systems. It contains regulators, GPO(s), charger + coulomb counter, RTC
and a clock gate.

All regulators can be controlled via I2C. LDO4 can additionally be set to
be enabled/disabled by a GPIO. LDO3 voltage could be selected from two
voltages written into separate VSEL reisters using GPIO but this mode is
not supported by driver. On top of that the PMIC has the typical HW
state machine which is present also on many other ROHM PMICs.

IC contains two GPOs - but one of the GPOs is marked as GND in
data-sheet. Thus the driver by default only exposes one GPO. The second
GPO can be enabled by special DT property.

RTC is almost similar to what is on BD71828. For currently used features
only the register address offset to RTC block differs.

The charger driver is not included in this series. ROHM has a charger
driver with some fuel-gauging logig written in but this is not included
here. I am working on separating the logic from HW specific driver and
supporting both BD71815 and BD71828 chargers in separate patch series.

Changelog v5:
  Regulator:
  - Added regmap helper for regulator ramp-delay and taken it in use
    (patches 13, 14, 16 - they can be just dropped if ramp-delay helper is not
    a good idea. Patch 15 implements old-fashioned ramp-delay)
  GPIO:
  - styling changes to GPIO (Mostly suggested by Andy)
  - implemented init_valid_mask (but can't count on it yet)
Changelog v4:
  - Sorted ROHM chip ID enum
  - Statcized DVS structures in regulator driver
  - Minor styling for regulator driver
  - rebased on v5.12-rc4
Changelog v3:
  - GPIO clean-up as suggested by Bartosz
  - MFD clean-up as suggested by Lee
  - clk-mode dt-binding handling in MFD driver corrected to reflect new
    property values.
  - Dropped already applied patches
  - Rebased on v5.12-rc2
Changelog v2:
  - Rebased on top of v5.11-rc3
  - Added another "preliminary patch" which fixes HW-dvs voltage
    handling (patch 1)
  - split regulator patch to two.
  - changed dt-binding patch ordering.
  regulators:
    - staticized probe
    - removed some unnecessary defines
    - updated comments
    - split rohm-regulator patch adding SNVS and supporting simple
      linear mapping into two - one adding support for mapping, other
      adding SNVS.
  GPIO:
    - removed unnecessary headers
    - clarified dev/parent->dev usage
    - removed forgotten #define DEBUG
  dt-bindings:
    - changed patch order to meet ref-dependencies
    - added missing regulator nodes
    - changed string property for clk mode to tristated
  MFD:
    - header cleanups.
  CLK:
    - fixed commit message

--

Matti Vaittinen (19):
  rtc: bd70528: Do not require parent data
  mfd: bd718x7: simplify by cleaning unnecessary device data
  dt_bindings: bd71828: Add clock output mode
  dt_bindings: regulator: Add ROHM BD71815 PMIC regulators
  dt_bindings: mfd: Add ROHM BD71815 PMIC
  mfd: Add ROHM BD71815 ID
  mfd: Sort ROHM chip ID list for better readability
  mfd: Support for ROHM BD71815 PMIC core
  gpio: support ROHM BD71815 GPOs
  regulator: helpers: Export helper voltage listing
  regulator: rohm-regulator: linear voltage support
  regulator: rohm-regulator: Support SNVS HW state.
  regulator: Add regmap helper for ramp-delay setting
  regulator: bd718x7, bd71828: Use ramp-delay helper
  regulator: Support ROHM BD71815 regulators
  regulator: bd71815: use ramp-delay helper
  clk: bd718x7: Add support for clk gate on ROHM BD71815 PMIC
  rtc: bd70528: Support RTC on ROHM BD71815
  MAINTAINERS: Add ROHM BD71815AGW

 .../bindings/mfd/rohm,bd71815-pmic.yaml       | 201 ++++++
 .../bindings/mfd/rohm,bd71828-pmic.yaml       |   6 +
 .../regulator/rohm,bd71815-regulator.yaml     | 116 ++++
 MAINTAINERS                                   |   3 +
 drivers/clk/clk-bd718x7.c                     |   9 +-
 drivers/gpio/Kconfig                          |  10 +
 drivers/gpio/Makefile                         |   1 +
 drivers/gpio/gpio-bd71815.c                   | 193 ++++++
 drivers/mfd/Kconfig                           |  15 +-
 drivers/mfd/rohm-bd71828.c                    | 486 +++++++++----
 drivers/mfd/rohm-bd718x7.c                    |  43 +-
 drivers/regulator/Kconfig                     |  11 +
 drivers/regulator/Makefile                    |   1 +
 drivers/regulator/bd71815-regulator.c         | 651 ++++++++++++++++++
 drivers/regulator/bd71828-regulator.c         |  51 +-
 drivers/regulator/bd718x7-regulator.c         |  60 +-
 drivers/regulator/helpers.c                   | 101 ++-
 drivers/regulator/rohm-regulator.c            |  23 +-
 drivers/rtc/Kconfig                           |   6 +-
 drivers/rtc/rtc-bd70528.c                     | 104 +--
 include/linux/mfd/rohm-bd71815.h              | 562 +++++++++++++++
 include/linux/mfd/rohm-bd71828.h              |   3 +
 include/linux/mfd/rohm-bd718x7.h              |  13 -
 include/linux/mfd/rohm-generic.h              |  15 +-
 include/linux/regulator/driver.h              |   7 +
 25 files changed, 2393 insertions(+), 298 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml
 create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd71815-regulator.yaml
 create mode 100644 drivers/gpio/gpio-bd71815.c
 create mode 100644 drivers/regulator/bd71815-regulator.c
 create mode 100644 include/linux/mfd/rohm-bd71815.h

base-commit: 0d02ec6b
--
2.25.4

--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]

Quite a few regulator ICs do support setting ramp-delay by writing a value
matching the delay to a ramp-delay register.

Provide a simple helper for table-based delay setting.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/f101f1db564cf32cb58719c77af0b00d7236bb89.1617020713.git.matti.vaittinen@fi.rohmeurope.comSigned-off-by: Mark Brown <broonie@kernel.org>

Some drivers need to translate voltage values to selectors prior regulator
registration. Currently a regulator_desc based list_voltages helper is only
exported for regulators using the linear_ranges. Export similar helper also
for regulators using simple linear mapping.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/1200ef7a50c84327ada019b85f6527b4fc9b5ce1.1617020713.git.matti.vaittinen@fi.rohmeurope.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add PM7325/PMR735A compatibles for Qualcomm SC7280 platform.
Signed-off-by: satya priya <skakit@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1617192339-3760-6-git-send-email-skakit@codeaurora.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Convert RPMh regulator bindings from .txt to .yaml format.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1617192339-3760-5-git-send-email-skakit@codeaurora.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Add support for PM7325/PMR735A regulators. This ensures
that consumers are able to modify the physical state of PMIC
regulators.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1617192339-3760-3-git-send-email-skakit@codeaurora.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Add pmic5_ftsmps520 buck as this is required for PM7325
and PMR735A PMICs.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1617192339-3760-2-git-send-email-skakit@codeaurora.orgSigned-off-by: Mark Brown <broonie@kernel.org>

fixes coccicheck warning:

drivers/regulator/mt6360-regulator.c:384:3-10: line 384 is
redundant because platform_get_irq() already prints an error

in fact it is not platform_get_irq but platform_get_irq_byname print error
Signed-off-by: Jian Dong <dongjian@yulong.com>
Link: https://lore.kernel.org/r/1616555474-158789-1-git-send-email-dj0227@163.comSigned-off-by: Mark Brown <broonie@kernel.org>

Pull ext4 fixes from Ted Ts'o:
 "Miscellaneous ext4 bug fixes for v5.12"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: initialize ret to suppress smatch warning
  ext4: stop inode update before return
  ext4: fix rename whiteout with fast commit
  ext4: fix timer use-after-free on failed mount
  ext4: fix potential error in ext4_do_update_inode
  ext4: do not try to set xattr into ea_inode if value is empty
  ext4: do not iput inode under running transaction in ext4_rename()
  ext4: find old entry again if failed to rename whiteout
  ext4: fix error handling in ext4_end_enable_verity()
  ext4: fix bh ref count on error paths
  fs/ext4: fix integer overflow in s_log_groups_per_flex
  ext4: add reclaim checks to xattr code
  ext4: shrink race window in ext4_should_retry_alloc()

Pull io_uring followup fixes from Jens Axboe:

 - The SIGSTOP change from Eric, so we properly ignore that for
   PF_IO_WORKER threads.

 - Disallow sending signals to PF_IO_WORKER threads in general, we're
   not interested in having them funnel back to the io_uring owning
   task.

 - Stable fix from Stefan, ensuring we properly break links for short
   send/sendmsg recv/recvmsg if MSG_WAITALL is set.

 - Catch and loop when needing to run task_work before a PF_IO_WORKER
   threads goes to sleep.

* tag 'io_uring-5.12-2021-03-21' of git://git.kernel.dk/linux-block:
  io_uring: call req_set_fail_links() on short send[msg]()/recv[msg]() with MSG_WAITALL
  io-wq: ensure task is running before processing task_work
  signal: don't allow STOP on PF_IO_WORKER threads
  signal: don't allow sending any signals to PF_IO_WORKER threads

Pull staging and IIO driver fixes from Greg KH:
 "Some small staging and IIO driver fixes:

   - MAINTAINERS changes for the move of the staging mailing list

   - comedi driver fixes to get request_irq() to work correctly

   - counter driver fixes for reported issues with iio devices

   - tiny iio driver fixes for reported issues.

  All of these have been in linux-next with no reported problems"

* tag 'staging-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: vt665x: fix alignment constraints
  staging: comedi: cb_pcidas64: fix request_irq() warn
  staging: comedi: cb_pcidas: fix request_irq() warn
  MAINTAINERS: move the staging subsystem to lists.linux.dev
  MAINTAINERS: move some real subsystems off of the staging mailing list
  iio: gyro: mpu3050: Fix error handling in mpu3050_trigger_handler
  iio: hid-sensor-temperature: Fix issues of timestamp channel
  iio: hid-sensor-humidity: Fix alignment issue of timestamp channel
  counter: stm32-timer-cnt: fix ceiling miss-alignment with reload register
  counter: stm32-timer-cnt: fix ceiling write max value
  counter: stm32-timer-cnt: Report count function when SLAVE_MODE_DISABLED
  iio: adc: ab8500-gpadc: Fix off by 10 to 3
  iio:adc:stm32-adc: Add HAS_IOMEM dependency
  iio: adis16400: Fix an error code in adis16400_initial_setup()
  iio: adc: adi-axi-adc: add proper Kconfig dependencies
  iio: adc: ad7949: fix wrong ADC result due to incorrect bit mask
  iio: hid-sensor-prox: Fix scale not correct issue
  iio:adc:qcom-spmi-vadc: add default scale to LR_MUX2_BAT_ID channel

Pull USB and Thunderbolt driver fixes from Greg KH:
 "Here are some small Thunderbolt and USB driver fixes for some reported
  issues:

   - thunderbolt fixes for minor problems

   - typec fixes for power issues

   - usb-storage quirk addition

   - usbip bugfix

   - dwc3 bugfix when stopping transfers

   - cdnsp bugfix for isoc transfers

   - gadget use-after-free fix

  All have been in linux-next this week with no reported issues"

* tag 'usb-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: tcpm: Skip sink_cap query only when VDM sm is busy
  usb: dwc3: gadget: Prevent EP queuing while stopping transfers
  usb: typec: tcpm: Invoke power_supply_changed for tcpm-source-psy-
  usb: typec: Remove vdo[3] part of tps6598x_rx_identity_reg struct
  usb-storage: Add quirk to defeat Kindle's automatic unload
  usb: gadget: configfs: Fix KASAN use-after-free
  usbip: Fix incorrect double assignment to udc->ud.tcp_rx
  usb: cdnsp: Fixes incorrect value in ISOC TRB
  thunderbolt: Increase runtime PM reference count on DP tunnel discovery
  thunderbolt: Initialize HopID IDAs in tb_switch_alloc()

Pull irq fix from Ingo Molnar:
 "A change to robustify force-threaded IRQ handlers to always disable
  interrupts, plus a DocBook fix.

  The force-threaded IRQ handler change has been accelerated from the
  normal schedule of such a change to keep the bad pattern/workaround of
  spin_lock_irqsave() in handlers or IRQF_NOTHREAD as a kludge from
  spreading"

* tag 'irq-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Disable interrupts for force threaded handlers
  genirq/irq_sim: Fix typos in kernel doc (fnode -> fwnode)

Pull perf fixes from Ingo Molnar:
 "Boundary condition fixes for bugs unearthed by the perf fuzzer"

* tag 'perf-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Fix unchecked MSR access error caused by VLBR_EVENT
  perf/x86/intel: Fix a crash caused by zero PEBS status

Pull locking fixes from Ingo Molnar:

 - Get static calls & modules right. Hopefully.

 - WW mutex fixes

* tag 'locking-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  static_call: Fix static_call_update() sanity check
  static_call: Align static_call_is_init() patching condition
  static_call: Fix static_call_set_init()
  locking/ww_mutex: Fix acquire/release imbalance in ww_acquire_init()/ww_acquire_fini()
  locking/ww_mutex: Simplify use_ww_ctx & ww_ctx handling