During a hibernate/resume cycle, the whole system is reset, including
the GuC and the doorbell hardware. Then the system is booted up, drivers
are loaded, etc -- the GuC firmware may be loaded and set running at
this point. But then, the booted kernel is replaced by the hibernated
image, and this resumed kernel will also try to reload the GuC firmware
(which will fail). To recover, we reset the GuC and try again (which
should work). But this GuC reset doesn't also reset the doorbell
hardware, so it can be left in a state inconsistent with that assumed
by the driver and/or the newly-loaded GuC firmware.

It would be better if the GuC reset also cleared all doorbell state,
but that's not how the hardware currently works; also, the driver cannot
directly reprogram the doorbell hardware (only the GuC can do that).

So this patch cycles through all doorbells, assigning and releasing each
in turn, so that all the doorbell hardware is left in a consistent
state, no matter how it was programmed by the previously-running kernel
and/or GuC firmware.

v2: don't use kmap_atomic() now that client page 0 is kept mapped.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465837054-16245-2-git-send-email-david.s.gordon@intel.com

This version doesn't update the doorbell bitmap, as that will
be done when the selected doorbell is associated with a client.

The call is now slightly earlier, just on the general principle
that potentially-failing operations should be done as early as
possible, to eliminate late failures and simplify recovery.
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

This patch refactors the driver's handling and tracking of doorbells, in
preparation for a later one which will resolve a suspend-resume issue.

There are three resources to be managed:
1. Cachelines: a single line within the client-object's page 0
   is snooped by doorbell hardware for writes from the host.
2. Doorbell registers: each defines one cacheline to be snooped.
3. Bitmap: tracks which doorbell registers are in use.

The doorbell setup/teardown protocol starts with:
1. Pick a cacheline: select_doorbell_cacheline()
2. Find an available doorbell register: assign_doorbell()
(These values are passed to the GuC via the shared context
descriptor; this part of the sequence remains unchanged).

3. Update the bitmap to reflect registers-in-use
4. Prepare the cacheline for use by setting its status to ENABLED
5. Ask the GuC to program the doorbell to snoop the cacheline

and of course teardown is very similar:
6. Set the cacheline to DISABLED
7. Ask the GuC to reprogram the doorbell to stop snooping
8. Record that the doorbell is not in use.

Operations 6-8 (guc_disable_doorbell(), host2guc_release_doorbell(), and
release_doorbell()) were called in sequence from guc_client_free(), but
are now moved into the teardown phase of the common function.

Steps 4-5 (guc_init_doorbell() and host2guc_allocate_doorbell()) were
similarly done as sequential steps in guc_client_alloc(), but since it
turns out that we don't need to be able to do them separately they're
now collected into the setup phase of the common function.

The only new code (and new capability) is the block tagged
    /* Update the GuC's idea of the doorbell ID */
i.e. we can now *change* the doorbell register used by an existing
client, whereas previously it was set once for the entire lifetime
of the client. We will use this new feature in the next patch.

v2: Trivial independent fixes pushed ahead as separate patches.
    MUCH longer commit message :) [Tvrtko Ursulin]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

Just code movement, no actual change to the function. This is in
preparation for the next patch, which will reorganise all the other
doorbell code, but doesn't change this function. So let's shuffle it
down near its caller rather than leaving it mixed in with the setup
code. Unlike the doorbell management code, this function is somewhat
time-critical, so putting it near its caller may even yield a tiny
performance improvement.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

These registers are not actually writable by the CPU; only the GuC can
actually program them. So let's not do writes that have no effect.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

Bitmap operators are overkill when touching only one bit.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

To properly verify the driver->doorbell->GuC functionality, validation
needs to know how the driver has assigned the doorbell cache lines and
registers, so make them visible through debugfs.

v2: use kernel bitmap-printing format (%pb) rather than %x.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

This is a WA affecting pooled eu which is a bxt specific feature.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Winiarski, Michal <michal.winiarski@intel.com>
Cc: Zou, Nanhai <nanhai.zou@intel.com>
Cc: Yang, Rong R <rong.r.yang@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

Pooled EU is enabled by default for BXT but for fused down 2x6 parts it is
advised to turn it off. But there is another HW issue in these parts (fused
down 2x6 parts) before C0 that requires Pooled EU to be enabled as a
workaround. In this case the pool configuration changes depending upon
which subslice is disabled. This doesn't affect if the device has all 3
subslices enabled.

Userspace need to know min no. of eus in a pool as it varies based on which
subslice is disabled, this is not yet exported because userspace support is
not available yet. Once the support is available this needs to be exported
using getparam ioctls.

v2: s/subslice_total/subslice_per_slice as it is a more logical field (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Winiarski, Michal <michal.winiarski@intel.com>
Cc: Zou, Nanhai <nanhai.zou@intel.com>
Cc: Yang, Rong R <rong.r.yang@intel.com>
Cc: Tim Gore <tim.gore@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

This mode allows to assign EUs to pools which can process work collectively.
The command to enable this mode should be issued as part of context initialization.

The pooled mode is global, once enabled it has to stay the same across all
contexts until HW reset hence this is sent in auxiliary golden context batch.
Thanks to Mika for the preliminary review and comments.

v2: explain why this is enabled in golden context, use feature flag while
enabling the support (Chris)

v3: Include only kernel support as userspace support is not available yet.

User space clients need to know when the pooled EU feature is present
and enabled on the hardware so that they can adapt work submissions.
Create a new device info flag for this purpose.

Set has_pooled_eu to true in the Broxton static device info - Broxton
supports the feature in hardware and the driver will enable it by
default.

We need to add getparam ioctls to enable userspace to query availability of
this feature and to retrieve min. no of eus in a pool but we will expose
them once userspace support is available. Opensource users for this feature
are mesa, libva and beignet.

Beignet team is currently working on adding userspace support.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Cc: Winiarski, Michal <michal.winiarski@intel.com>
Cc: Zou, Nanhai <nanhai.zou@intel.com>
Cc: Yang, Rong R <rong.r.yang@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Armin Reese <armin.c.reese@intel.com>
Cc: Tim Gore <tim.gore@intel.com>
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

There are four non-static functions in i915_guc_submission.c that take a
'dev' parameter. All are called only from GuC loader code, and can be
easily converted to accept 'dev_priv' instead.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465579766-31595-1-git-send-email-david.s.gordon@intel.com

Convert all static functions in i915_guc_submission.c that currently
take a 'dev' pointer to take 'dev_priv' instead (there are three,
guc_client_alloc(), guc_client_free(), and gem_allocate_guc_obj().
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

We can check the power state of the PHY data and common lanes as
reported by the PHY. Do this in case we need to debug problems where the
PHY gets stuck in an unexpected state.

Note that I only check these when the lanes are expected to be powered
on purpose, since it's not clear at what point the PHY power/clock gates
things.

v2:
- Don't report the encoder as disabled when the sanity check fails.
  (Ville)

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465825477-32671-1-git-send-email-imre.deak@intel.com

Rename these remaining function prefixes to better align with the
corresponding SKL functions.

No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

So far we configured a static lane latency optimization during driver
loading/resuming. The specification changed at one point and now this
configuration depends on the lane count, so move the configuration
to modeset time accordingly.

It's not clear when this lane configuration takes effect. The
specification only requires that the programming is done before enabling
the port. On CHV OTOH the lanes start to power up already right after
enabling the PLL. To be safe preserve the current order and set things
up already before enabling the PLL.

v2: (Ander)
- Simplify the optimization mask calculation.
- Use the correct pipe_config always during the calculation instead
  of the bogus intel_crtc->config.

CC: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95476Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

So far we depended on the HW to dynamically power down unused PHYs and
so we enabled them manually once during driver loading/resuming. There
are indications however that we can achieve better power savings by
manual powering toggling. So make the PHY enabling/disabling to happen
on-demand whenever we need either the corresponding AUX or port
functionality. CHV does this already by enabling the PHY along the
corresponding PHY common lane power wells there, do the same on BXT by
adding virtual power wells for the same purpose.

Also sanity check the common lane power down ack signal from the PHY. Do
this only when the PHY is enabled, since it's not clear at what point
the HW power/clock gates things.

While at it rename broxton_ prefix to bxt_ in related function names to
better align with the SKL code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

These helpers will be needed by the next patch, so factor them out.

No functional change.

v2:
- Move the refcount==0 WARN to the new put helper. (Ville)

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

A follow-up patch moves the PHY enabling to the power well code where
enabling/disabling the PHYs will happen independently. Because of this
waiting for the GRC calibration in PHY1 asynchronously would need some
additional logic. Instead of adding that let's keep things simple for now
and wait synchronously. My measurements showed that the calibration
takes ~4ms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465821536-21312-1-git-send-email-kraxel@redhat.com

It seems pretty clear that bitwise OR was intended here and not logical
OR.

Fixes: 6fc29133 ('drm/i915/gen9: Add WaDisableSkipCaching')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>

Calling drm_framebuffer_unregister_private() in intel_fbdev_destroy() is
superfluous because the framebuffer will subsequently be unregistered by
drm_framebuffer_free() when unreferenced in drm_framebuffer_remove().
The call is a leftover, when it was introduced by commit 36206361
("drm: revamp framebuffer cleanup interfaces"), struct intel_framebuffer
was still embedded in struct intel_fbdev rather than being a pointer as
it is today, and drm_framebuffer_remove() wasn't used yet.

As a bonus, the ID of the framebuffer is no longer 0 in the debug log:

Before:
    [   39.680874] [drm:drm_mode_object_unreference] OBJ ID: 0 (3)
    [   39.680878] [drm:drm_mode_object_unreference] OBJ ID: 0 (2)
    [   39.680884] [drm:drm_mode_object_unreference] OBJ ID: 0 (1)

After:
    [  102.504649] [drm:drm_mode_object_unreference] OBJ ID: 45 (3)
    [  102.504651] [drm:drm_mode_object_unreference] OBJ ID: 45 (2)
    [  102.504654] [drm:drm_mode_object_unreference] OBJ ID: 45 (1)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/5031860caad67faa0f1be5965331ef048a311a01.1465383212.git.lukas@wunner.de

This patch enables a workaround for a mid thread preemption
issue where a hardware timing problem can prevent the
context restore from happening, leading to a hang.

v2: move to gen9_init_workarounds (Arun)
v3: move to start of gen9_init_workarounds (Arun)
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465816501-25557-1-git-send-email-tim.gore@intel.com

This patch adds support for extending the pread/pwrite functionality
for objects not backed by shmem. The access will be made through
gtt interface. This will cover objects backed by stolen memory as well
as other non-shmem backed objects.

v2: Drop locks around slow_user_access, prefault the pages before
access (Chris)

v3: Rebased to the latest drm-intel-nightly (Ankit)

v4: Moved page base & offset calculations outside the copy loop,
corrected data types for size and offset variables, corrected if-else
braces format (Tvrtko/kerneldocs)

v5: Enabled pread/pwrite for all non-shmem backed objects including
without tiling restrictions (Ankit)

v6: Using pwrite_fast for non-shmem backed objects as well (Chris)

v7: Updated commit message, Renamed i915_gem_gtt_read to i915_gem_gtt_copy,
added pwrite slow path for non-shmem backed objects (Chris/Tvrtko)

v8: Updated v7 commit message, mutex unlock around pwrite slow path for
non-shmem backed objects (Tvrtko)

v9: Corrected check during pread_ioctl, to avoid shmem_pread being
called for non-shmem backed objects (Tvrtko)

v10: Moved the write_domain check to needs_clflush and tiling mode check
to pwrite_fast (Chris)

v11: Use pwrite_fast fallback for all objects (shmem and non-shmem backed),
call fast_user_write regardless of pagefault in previous iteration

v12: Use page-by-page copy for slow user access too (Chris)

v13: Handled EFAULT, Avoid use of WARN_ON, put_fence only if whole obj
pinned (Chris)

v14: Corrected datatypes/initializations (Tvrtko)

Testcase: igt/gem_stolen, igt/gem_pread, igt/gem_pwrite
Signed-off-by: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465548783-19712-1-git-send-email-ankitprasad.r.sharma@intel.com

In pwrite_fast, map an object page by page if obj_ggtt_pin fails. First,
we try a nonblocking pin for the whole object (since that is fastest if
reused), then failing that we try to grab one page in the mappable
aperture. It also allows us to handle objects larger than the mappable
aperture (e.g. if we need to pwrite with vGPU restricting the aperture
to a measely 8MiB or something like that).

v2: Pin pages before starting pwrite, Combined duplicate loops (Chris)

v3: Combined loops based on local patch by Chris (Chris)

v4: Added i915 wrapper function for drm_mm_insert_node_in_range (Chris)

v5: Renamed wrapper function for drm_mm_insert_node_in_range (Chris)

v5: Added wrapper for drm_mm_remove_node() (Chris)

v6: Added get_pages call before pinning the pages (Tvrtko)
Added remove_mappable_node() wrapper for drm_mm_remove_node() (Chris)

v7: Added size argument for insert_mappable_node (Tvrtko)

v8: Do not put_pages after pwrite, do memset of node in the wrapper
function (insert_mappable_node) (Chris)

v9: Rebase (Ankit)
Signed-off-by: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

This utility function is a companion to i915_gem_object_get_page() that
uses the same cached iterator for the scatterlist to perform fast
sequential lookup of the dma address associated with any page within the
object.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

Introduced a new vm specfic callback insert_page() to program a single pte in
ggtt or ppgtt. This allows us to map a single page in to the mappable aperture
space. This can be iterated over to access the whole object by using space as
meagre as page size.

v2: Added low level rpm assertions to insert_page routines (Chris)

v3: Added POSTING_READ post register write (Tvrtko)

v4: Rebase (Ankit)

v5: Removed wmb() and FLUSH_CTL from insert_page, caller to take care
of it (Chris)

v6: insert_page not working correctly without FLSH_CNTL write, added the
write again.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

If the user doesn't override the default values of the GuC-related
kernel parameters, then on a non-GuC-based platform we shouldn't
mention that we haven't loaded the GuC firmware.

The various messages have been reordered into a least->most severe
cascade (none/INFO/INFO/ERROR) for ease of comprehension.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465575685-34169-1-git-send-email-david.s.gordon@intel.com

This reverts commit f165d283.

It breaks one of our CI systems. Quoting from Ville:

[   13.100979] [drm:ironlake_init_pch_refclk] has_panel 1 has_lvds 1 has_ck505 0 using_ssc_source 1
[   13.101413] ------------[ cut here ]------------
[   13.101429] kernel BUG at drivers/gpu/drm/i915/intel_display.c:8528!

"which is the 'BUG_ON(val != final)' at the end of ironlake_init_pch_refclk()."

Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude <cpaul@redhat.com>
Cc: marius.c.vlad@intel.com
References: https://www.spinics.net/lists/dri-devel/msg109557.htmlAcked-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

Add this fbc related workaround for all gen9

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-28-git-send-email-mika.kuoppala@intel.com

Bspec states that we need to set nuke on modify all to prevent
screen corruption with fbc on skl and kbl.

v2: proper workaround name

References: HSD#2227109, HSDES#1404569388
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-27-git-send-email-mika.kuoppala@intel.com

Set bit 8 in 0x43224 to prevent screen corruption and system
hangs on high memory bandwidth conditions. The same wa also suggest
setting bit 31 on ARB_CTL. According to another workaround we gain
better idle power savings when FBC is enabled.

v2: use correct workaround name
v3: split out overlapping wa for corruption avoidance (Ville)

References: HSD#2137218, HSD#2227171, HSD#2136579, BSID#883
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-26-git-send-email-mika.kuoppala@intel.com

According to bspec this prevents screen corruption when fbc is
used.

v2: This workaround has a name, use it (Ville)
v3: remove bogus gen check on ilk/vlv wm path (Ville)

References: HSD#2135555, HSD#2137270, BSID#562
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-25-git-send-email-mika.kuoppala@intel.com

This workaround for bdw and chv, is also needed for kbl A0.

References: HSD#1911519, BSID#569
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-24-git-send-email-mika.kuoppala@intel.com

There is ambiguity in the documentation between D0 and E0.
Extend this workaround to E0.

References: BSID#779
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-23-git-send-email-mika.kuoppala@intel.com

Workaround for display underrun issues with Y & Yf Tiling.
Set this on all gen9 as stated by bspec.

v2: proper workaround name

References: HSD#2136383, BSID#857
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-22-git-send-email-mika.kuoppala@intel.com

This is needed for all kbl revision.

v2: Don't add revid checks to generic gen9 init (Arun)

References: HSD#2135593
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-21-git-send-email-mika.kuoppala@intel.com

We need to disable clock gating in this unit to work around
hardware issue causing possible corruption/hang.

v2: name the bit (Ville)
v3: leave the fix enabled for 2227050 and set correct bit (Matthew)
v4: Split out the skl part in separate commit for easier backport

References: HSD#2227156, HSD#2227050
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-20-git-send-email-mika.kuoppala@intel.com

Add this workaround for A0 and B0 revisions

References: HSD#2226935
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-19-git-send-email-mika.kuoppala@intel.com

This workaround is for fbc working with rc6 on skylake. Bspec
states that setting this bit needs to be coordinated with uncore
but offers no further details.

v2: rebase

References: HSD#4712857
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-18-git-send-email-mika.kuoppala@intel.com

Make sure that we never enable skip caching on gen9 by
accident.

References: HSD#2134698
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-17-git-send-email-mika.kuoppala@intel.com