- 23 Sep, 2023 1 commit
-
-
Luca Weiss authored
Now that the pm7250b.dtsi can be configured to be on a different SID, we also need to specify it for this dts file. Set it to the SID 2/3 like it was before commit 8e2d56f6 ("arm64: dts: qcom: pm7250b: make SID configurable"). Fixes: 8e2d56f6 ("arm64: dts: qcom: pm7250b: make SID configurable") Signed-off-by:
Luca Weiss <luca.weiss@fairphone.com> Link: https://lore.kernel.org/r/20230921-pm7250b-sid-fixup-v1-1-231c1a65471f@fairphone.comSigned-off-by:
Bjorn Andersson <andersson@kernel.org>
-
- 22 Sep, 2023 1 commit
-
-
Vignesh Raman authored
Due to the presence of the fastboot micro cable in the CI farm, it causes the hardware to remain in gadget mode instead of host mode. So it doesn't find the network, which results in failure to mount root fs via NFS. Add an overlay dtso file that sets the dr_mode to host, allowing the USB controllers to work in host mode. With commit 15d16d6d ("kbuild: Add generic rule to apply fdtoverlay"), overlay target can be used to simplify the build of DTB overlays. It uses fdtoverlay to merge base device tree with the overlay dtso. apq8016-sbc-usb-host.dtb file can be used by drm-ci, mesa-ci. Suggested-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Suggested-by:
Maxime Ripard <mripard@kernel.org> Signed-off-by:
Helen Koike <helen.koike@collabora.com> Signed-off-by:
David Heidelberg <david.heidelberg@collabora.com> Signed-off-by:
Vignesh Raman <vignesh.raman@collabora.com> Reviewed-by:
-
- 20 Sep, 2023 38 commits
-
-
Luca Weiss authored
Add device tree for the Fairphone 5 smartphone which is based on the QCM6490 SoC. Supported features are, as of now: * Bluetooth * Debug UART * Display via simplefb * Flash/torch LED * Flip cover sensor * Power & volume buttons * RTC * SD card * USB * Various plumbing like regulators, i2c, spi, etc Signed-off-by:
Konrad Dybcio <konrad.dybcio@linaro.org> Tested-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20230919-fp5-initial-v2-7-14bb7cedadf5@fairphone.comSigned-off-by:
-
Luca Weiss authored
Fairphone 5 is a smartphone based on the QCM6490 SoC. Signed-off-by:
-
Luca Weiss authored
Add a node for the led controller found on PM8350C, used for flash and torch purposes. Signed-off-by:
-
Luca Weiss authored
Like other Qualcomm PMICs the PM7250B can be used on different addresses on the SPMI bus. Use similar defines like the PMK8350 to make this possible but skip the ifndef based on maintainer feedback. Signed-off-by:
-
Luca Weiss authored
With the standard Qualcomm TrustZone setup, components such as lpasscc, pdc_reset and watchdog shouldn't be touched by Linux. Mark them with the status 'reserved' and reenable them in the chrome-common dtsi. Signed-off-by:
-
Gaurav Kohli authored
Fix the apps iommu local address space range as per data sheet. Fixes: 61550c6c ("arm64: dts: qcom: Add msm8939 SoC") Signed-off-by:
Gaurav Kohli <quic_gkohli@quicinc.com> Reviewed-by:
Stephan Gerhold <stephan@gerhold.net> Link: https://lore.kernel.org/r/20230917140039.25283-1-quic_gkohli@quicinc.comSigned-off-by:
-
Robert Marko authored
Now that SCM has support for indicating that SDI has been enabled by default, lets set the property so SCM disables it during probing. Signed-off-by:
Robert Marko <robimarko@gmail.com> Link: https://lore.kernel.org/r/20230816164641.3371878-4-robimarko@gmail.comSigned-off-by:
-
Adam Skladowski authored
Update bits to match downstream irq-bitmask values. Fixes: 0484d3ce ("arm64: dts: qcom: Add DTS for MSM8976 and MSM8956 SoCs") Signed-off-by:
Adam Skladowski <a39.skl@gmail.com> Link: https://lore.kernel.org/r/20230812112534.8610-8-a39.skl@gmail.comSigned-off-by:
-
Adam Skladowski authored
MSM8976 downstream dts define reloc region which is used by pil-tz to load both wcnss and lpass, on mainline however we might not be able to do it and we need separate regions(also validating dts might get problematic if we had to put memory-region(rproc node) per device). Luckily it seems size and entry points in firmware headers appears to be static across multiple devices including Sony Loire platform and Xiaomi Redmi Note 3 Pro this should let us fit in first ~17MB Split lpass region(reloc on downstream) into two separate regions. Signed-off-by:
-
Danila Tikhonov authored
WLED is used for controlling the backlight on some boards, add the node for it. Signed-off-by:
Danila Tikhonov <danila@jiaxyga.com> Link: https://lore.kernel.org/r/20230913185514.21840-1-danila@jiaxyga.comSigned-off-by:
-
Bartosz Golaszewski authored
Add an ICE node to sa8775p SoC description and enable it by adding a phandle to the UFS node. Signed-off-by:
Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by:
-
Stephan Gerhold authored
Both MSM8916 and MSM8939 have unnecessarily large reservations for the venus firmware for some reason. According to the ELF headers and downstream [1] 5 MiB is enough. Let's set the minimum size as default. With the dynamic reserved memory allocations boards can easily override this if needed, although in practice there does not seem to be any device with a different venus firmware size. [1]: https://git.codelinaro.org/clo/la/kernel/msm-3.10/-/blame/LA.BR.1.2.9.1-02310-8x16.0/arch/arm/boot/dts/qcom/msm8939-common.dtsi#L69Signed-off-by:
-
Stephan Gerhold authored
The modem firmware size is typically highly device-specific. The current size of the mpss_mem region in msm8916.dtsi (0x2b00000) only works for some APQ8016 devices without full-featured modem, such as the DragonBoard 410c. The full modem firmware is typically about twice as large (~45 MiB -> ~90 MiB) but also varies by a few MiB from device to device. Since these devices are quite memory-constrained nowadays it's important to minimize the unnecessary memory reservations. Make it clear that each board needs to specify the necessary mpss_mem size by replacing the DB410c-specific size in msm8916.dtsi with a simple comment. &mpss_mem is disabled by default so it's fine to leave some properties up to the boards if they want to enable it. Signed-off-by:
-
Stephan Gerhold authored
Now that we no longer have fixed addresses for the firmware memory regions, disable them by default and only enable them together with the actual user in the board DT. This frees up unnecessary reserved memory for boards that do not use some of the remoteprocs and allows moving selected device-specific properties (such as firmware size) to the board-specific DT part in the next step. Signed-off-by:
-
Stephan Gerhold authored
Follow the example of MSM8916 and reserve the firmware memory regions dynamically to allow boards to define only the device-specific parts. Signed-off-by:
-
Stephan Gerhold authored
At a first glance the MBA memory region on MSM8916 looks intentionally placed at the fixed address 0x8ea00000. This is what the ELF headers of the firmware specify as base address, and the typical Qualcomm-specific bits suggest the binary is not relocatable. However, on a closer look this is pointless: Unlike other firmware images the hardware expects to have the raw ELF image loaded to the MBA region, including the ELF header (without parsing it at all). This means that we actually just load the ELF header (not the code!) at 0x8ea00000. The real LOAD segments follow at arbitrary aligned addresses depending on the structure of the ELF binary. In practice it looks like we can use an arbitrary 1 MiB-aligned region for MBA. The downstream/vendor kernel just allocates this dynamically at an arbitrary (aligned) address. Drop the pointless fixed address and use the new dynamic reserved memory mechanism to allocate a region close to the others. This reduces gaps in the memory map and provides Linux with more contiguous memory. Signed-off-by:
-
Stephan Gerhold authored
Most of the reserved firmware memory on MSM8916 can be relocated when respecting the required alignment. To avoid having to precompute the reserved memory regions in every board DT, describe the actual requirements (size, alignment, alloc-ranges) using the dynamic reserved memory allocation. This approach has several advantages: 1. We can define "templates" for the reserved memory regions in msm8916.dtsi and keep only device-specific details in the board DT. This is useful for the "mpss" region size for example, which varies from device to device. It is no longer necessary to redefine all firmware regions to shift their addresses. 2. When some of the functionality (e.g. WCNSS, Modem, Venus) is not enabled or needed for a device, the reserved memory can stay disabled, freeing up the unused reservation for Linux. 3. Devices with special requirements for one of the firmware regions are handled automatically. For example, msm8916-longcheer-l8150 has non-relocatable "wcnss" firmware that must be loaded exactly at address 0x8b600000. When this is defined as a static region, the other dynamic allocations automatically adjust to a different place with suitable alignment. All in all this approach significantly reduces the boilerplate necessary to define the different firmware regions, and makes it easier to enable functionality on the different devices. Signed-off-by: -
Stephan Gerhold authored
gps_mem is needed by the modem firmware for GPS to work. However, it is accessed via QMI memshare [1] which is not available upstream yet. Until it lands upstream reserving this does not provide any advantage. [1]: https://lore.kernel.org/linux-arm-msm/20210319172321.22248-1-nikitos.tr@gmail.com/Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-3-b7089ec3e3a1@gerhold.netSigned-off-by:
-
Stephan Gerhold authored
MSM8916/39 do not need signed GPU firmware so it is generally okay to have it enabled by default. However, currently the GPU does not work without also enabling MDSS and it's questionable if someone would really need it without a display in practice. For consistency let's follow newer SoCs and disable the GPU by default. Enable it for all existing devices that already have &mdss enabled. Signed-off-by:
-
Stephan Gerhold authored
Venus needs firmware that is usually signed with a device-specific key. There are also devices that might not need it (especially during bring-up), so let's follow more recent SoCs and disable it by default. Enable it explicitly for all current devices except msm8916-mtp. That one has just UART enabled currently so it cannot really benefit from Venus. Signed-off-by:
-
Nikita Travkin authored
sc7180 has an ADSP remoteproc that exclusively controls the audio hardware on devices that use Qualcomm firmware. Add it along with the relevant audio services. Signed-off-by:
Nikita Travkin <nikita@trvn.ru> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20230907-sc7180-adsp-rproc-v3-4-6515c3fbe0a3@trvn.ruSigned-off-by:
-
Nikita Travkin authored
Some devices use tertiary mi2s to connect external audio codec. Add it near the other two i2s pinctrl definitions so the devices don't have to duplicate it. Signed-off-by:
-
Neil Armstrong authored
This reverts commit 76a6dd7b ("arm64: dts: qcom: sm8450: Add PRNG"), since the RNG HW on the SM8450 SoC is in fact a True Random Number Generator, a more appropriate compatible should be instead as reported at [1]. [1] https://lore.kernel.org/all/20230818161720.3644424-1-quic_omprsing@quicinc.com/Suggested-by:
Om Prakash Singh <quic_omprsing@quicinc.com> Suggested-by:
Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20230828-topic-sm8550-rng-v3-1-7a0678ca7988@linaro.orgSigned-off-by:
-
Stephan Gerhold authored
Drop the redundant reg-names and mclk from the PM8916 analog codec that were removed from the DT schema. Having the mclk on the analog codec is incorrect because only the digital codec consumes it directly. Signed-off-by:
-
Krzysztof Kozlowski authored
Device node names should be generic and bindings expect certain pattern for RPMh regulator nodes: sdx75-idp.dtb: rsc@17a00000: 'pmx75-rpmh-regulators' does not match any of the regexes: '^regulators(-[0-9])?$', 'pinctrl-[0-9]+' Fixes: 8a2dc39d ("arm64: dts: qcom: sdx75-idp: Add regulator nodes") Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm UFS phy switched from dedicated driver to QMP phy driver. Eventually the old driver was removed in commit 02dca8c9 ("phy: qcom: remove ufs qmp phy driver"). The original driver and its binding used vddp-ref-clk regulator supply, but the new one did not and left the supply unused. The Qualcomm UFS phy bindings were also migrated to newer ones and dropped support for vddp-ref-clk regulator in commit dc5cb635 ("dt-bindings: phy: migrate QMP UFS PHY bindings to qcom,sc8280xp-qmp-ufs-phy.yaml"). It turns out that this regulator, although with inaccurate name vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or similar, depending on the SoC) used by UFS controller. Bring back handling of this supply by using more appropriate regulator - UFS controller host supply. This also fixes dtbs_check warning: sm4250-oneplus-billie2.dtb: phy@4807000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm UFS phy switched from dedicated driver to QMP phy driver. Eventually the old driver was removed in commit 02dca8c9 ("phy: qcom: remove ufs qmp phy driver"). The original driver and its binding used vddp-ref-clk regulator supply, but the new one did not and left the supply unused. The Qualcomm UFS phy bindings were also migrated to newer ones and dropped support for vddp-ref-clk regulator in commit dc5cb635 ("dt-bindings: phy: migrate QMP UFS PHY bindings to qcom,sc8280xp-qmp-ufs-phy.yaml"). It turns out that this regulator, although with inaccurate name vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or similar, depending on the SoC) used by UFS controller. Bring back handling of this supply by using more appropriate regulator - UFS controller host supply. This also fixes dtbs_check warning: msm8998-xiaomi-sagit.dtb: phy@1da7000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm UFS phy switched from dedicated driver to QMP phy driver. Eventually the old driver was removed in commit 02dca8c9 ("phy: qcom: remove ufs qmp phy driver"). The original driver and its binding used vddp-ref-clk regulator supply, but the new one did not and left the supply unused. The Qualcomm UFS phy bindings were also migrated to newer ones and dropped support for vddp-ref-clk regulator in commit dc5cb635 ("dt-bindings: phy: migrate QMP UFS PHY bindings to qcom,sc8280xp-qmp-ufs-phy.yaml"). It turns out that this regulator, although with inaccurate name vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or similar, depending on the SoC) used by UFS controller. Bring back handling of this supply by using more appropriate regulator - UFS controller host supply. This also fixes dtbs_check warning: msm8998-oneplus-dumpling.dtb: phy@1da7000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm UFS phy switched from dedicated driver to QMP phy driver. Eventually the old driver was removed in commit 02dca8c9 ("phy: qcom: remove ufs qmp phy driver"). The original driver and its binding used vddp-ref-clk regulator supply, but the new one did not and left the supply unused. The Qualcomm UFS phy bindings were also migrated to newer ones and dropped support for vddp-ref-clk regulator in commit dc5cb635 ("dt-bindings: phy: migrate QMP UFS PHY bindings to qcom,sc8280xp-qmp-ufs-phy.yaml"). It turns out that this regulator, although with inaccurate name vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or similar, depending on the SoC) used by UFS controller. Bring back handling of this supply by using more appropriate regulator - UFS controller host supply. This also fixes dtbs_check warning: msm8998-mtp.dtb: phy@1da7000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm UFS phy switched from dedicated driver to QMP phy driver. Eventually the old driver was removed in commit 02dca8c9 ("phy: qcom: remove ufs qmp phy driver"). The original driver and its binding used vddp-ref-clk regulator supply, but the new one did not and left the supply unused. The Qualcomm UFS phy bindings were also migrated to newer ones and dropped support for vddp-ref-clk regulator in commit dc5cb635 ("dt-bindings: phy: migrate QMP UFS PHY bindings to qcom,sc8280xp-qmp-ufs-phy.yaml"). It turns out that this regulator, although with inaccurate name vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or similar, depending on the SoC) used by UFS controller. Bring back handling of this supply by using more appropriate regulator - UFS controller host supply. This also fixes dtbs_check warning: msm8998-fxtec-pro1.dtb: phy@1da7000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm UFS phy switched from dedicated driver to QMP phy driver. Eventually the old driver was removed in commit 02dca8c9 ("phy: qcom: remove ufs qmp phy driver"). The original driver and its binding used vddp-ref-clk regulator supply, but the new one did not and left the supply unused. The Qualcomm UFS phy bindings were also migrated to newer ones and dropped support for vddp-ref-clk regulator in commit dc5cb635 ("dt-bindings: phy: migrate QMP UFS PHY bindings to qcom,sc8280xp-qmp-ufs-phy.yaml"). It turns out that this regulator, although with inaccurate name vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or similar, depending on the SoC) used by UFS controller. Bring back handling of this supply by using more appropriate regulator - UFS controller host supply. This also fixes dtbs_check warning: msm8996-xiaomi-gemini.dtb: phy@627000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm UFS phy switched from dedicated driver to QMP phy driver. Eventually the old driver was removed in commit 02dca8c9 ("phy: qcom: remove ufs qmp phy driver"). The original driver and its binding used vddp-ref-clk regulator supply, but the new one did not and left the supply unused. The Qualcomm UFS phy bindings were also migrated to newer ones and dropped support for vddp-ref-clk regulator in commit dc5cb635 ("dt-bindings: phy: migrate QMP UFS PHY bindings to qcom,sc8280xp-qmp-ufs-phy.yaml"). It turns out that this regulator, although with inaccurate name vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or similar, depending on the SoC) used by UFS controller. Bring back handling of this supply by using more appropriate regulator - UFS controller host supply. This also fixes dtbs_check warning: msm8996-oneplus3t.dtb: phy@627000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm UFS phy switched from dedicated driver to QMP phy driver. Eventually the old driver was removed in commit 02dca8c9 ("phy: qcom: remove ufs qmp phy driver"). The original driver and its binding used vddp-ref-clk regulator supply, but the new one did not and left the supply unused. The Qualcomm UFS phy bindings were also migrated to newer ones and dropped support for vddp-ref-clk regulator in commit dc5cb635 ("dt-bindings: phy: migrate QMP UFS PHY bindings to qcom,sc8280xp-qmp-ufs-phy.yaml"). It turns out that this regulator, although with inaccurate name vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or similar, depending on the SoC) used by UFS controller. Bring back handling of this supply by using more appropriate regulator - UFS controller host supply. This also fixes dtbs_check warning: apq8096-db820c.dtb: phy@627000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm UFS phy switched from dedicated driver to QMP phy driver. Eventually the old driver was removed in commit 02dca8c9 ("phy: qcom: remove ufs qmp phy driver"). The original driver and its binding used vddp-ref-clk regulator supply, but the new one did not and left the supply unused. The Qualcomm UFS phy bindings were also migrated to newer ones and dropped support for vddp-ref-clk regulator in commit dc5cb635 ("dt-bindings: phy: migrate QMP UFS PHY bindings to qcom,sc8280xp-qmp-ufs-phy.yaml"). It turns out that this regulator, although with inaccurate name vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or similar, depending on the SoC) used by UFS controller. Bring back handling of this supply by using more appropriate regulator - UFS controller host supply. This also fixes dtbs_check warning: sm6115p-lenovo-j606f.dtb: phy@4807000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm UFS phy switched from dedicated driver to QMP phy driver. Eventually the old driver was removed in commit 02dca8c9 ("phy: qcom: remove ufs qmp phy driver"). The original driver and its binding used vddp-ref-clk regulator supply, but the new one did not and left the supply unused. The Qualcomm UFS phy bindings were also migrated to newer ones and dropped support for vddp-ref-clk regulator in commit dc5cb635 ("dt-bindings: phy: migrate QMP UFS PHY bindings to qcom,sc8280xp-qmp-ufs-phy.yaml"). It turns out that this regulator, although with inaccurate name vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or similar, depending on the SoC) used by UFS controller. Bring back handling of this supply by using more appropriate regulator - UFS controller host supply. This also fixes dtbs_check warning: sm6115-fxtec-pro1x.dtb: phy@4807000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm UFS phy switched from dedicated driver to QMP phy driver. Eventually the old driver was removed in commit 02dca8c9 ("phy: qcom: remove ufs qmp phy driver"). The original driver and its binding used vddp-ref-clk regulator supply, but the new one did not and left the supply unused. The Qualcomm UFS phy bindings were also migrated to newer ones and dropped support for vddp-ref-clk regulator in commit dc5cb635 ("dt-bindings: phy: migrate QMP UFS PHY bindings to qcom,sc8280xp-qmp-ufs-phy.yaml"). It turns out that this regulator, although with inaccurate name vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or similar, depending on the SoC) used by UFS controller. Bring back handling of this supply by using more appropriate regulator - UFS controller host supply. This also fixes dtbs_check warning: sm6125-xiaomi-laurel-sprout.dtb: phy@4807000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
Neither bindings nor UFS phy driver use properties like 'vdda-phy-max-microamp' and 'vdda-pll-max-microamp': sm6125-xiaomi-laurel-sprout.dtb: phy@4807000: 'vdda-phy-max-microamp', 'vdda-pll-max-microamp' do not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Vignesh Viswanathan authored
IPQ6018's TCSR Mutex HW lock register has 32 locks of size 4KB each. Total size of the TCSR Mutex registers is 128KB. Fix size of the tcsr_mutex hwlock register to 0x20000. Changes in v2: - Drop change to remove qcom,ipq6018-tcsr-mutex compatible string - Added Fixes and stable tags Cc: stable@vger.kernel.org Fixes: 5bf63562 ("arm64: dts: ipq6018: Add a few device nodes") Signed-off-by:
Vignesh Viswanathan <quic_viswanat@quicinc.com> Reviewed-by:
-
