This header uses 'bool', but it does not include any header by itself.

So, it could cause unknown type name error, depending on the header
include order, although probably <linux/types.h> has been included by
someone else.

Include <linux/types.h> to make it self-contained.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This fixes the warnings:

* include/linux/gpio.h:254:11: warning: 'struct pinctrl_dev' declared
  inside parameter list will not be visible outside of this definition
  or declaration
* include/linux/gpio/driver.h:602:11: warning: 'struct pinctrl_dev'
  declared inside parameter list will not be visible outside of this
  definition or declaration

Fixes: 78b99577 ("pinctrl: remove unused pin_is_valid()")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Enrico Weigelt <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Allwinner V3 SoC, despite come with the same die with V3s, has more
GPIO pins than V3s, and a different compatible string for pinctrl is
needed.

Add the compatible string for V3 pinctrl.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The pinctrl driver of V3s is already available and used in the kernel,
but the compatible string of it is forgotten to be added.

Add the missing compatible string.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch provides basic support for booting with ACPI instead
of the currently supported Device Tree.  When doing so there are a
couple of differences which we need to taken into consideration.

Firstly, the SDM850 ACPI tables omit information pertaining to the
4 reserved GPIOs on the platform.  If Linux attempts to touch/
initialise any of these lines, the firmware will restart the
platform.

Secondly, when booting with ACPI, it is expected that the firmware
will set-up things like; Regulators, Clocks, Pin Functions, etc in
their ideal configuration.  Thus, the possible Pin Functions
available to this platform are not advertised when providing the
higher GPIOD/Pinctrl APIs with pin information.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When booting MSM based platforms with Device Tree or some ACPI
implementations, it is possible to provide a list of reserved pins
via the 'gpio-reserved-ranges' and 'gpios' properties respectively.
However some ACPI tables are not populated with this information,
thus it has to come from a knowledgable device driver instead.

Here we provide the MSM common driver with additional support to
parse this informtion and correctly populate the widely used
'valid_mask'.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This function was used by pin_request() to pointlessly double-check
the pin validity, and it was the only user ever.

Since commit d2f6a1c6 ("pinctrl: remove double pin validity
check."), no one has ever used it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The iterator is initialized in list_for_each_entry().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'sh-pfc-for-v5.3-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: sh-pfc: Updates for v5.3

  - Add more checks for pinctrl table validation,
  - Add TPU (Timer Pulse Unit / PWM) pin groups on R-Car H3, M3-W, and
    M3-N,
  - Rework description of pins without GPIO functionality,
  - Small fixes and cleanups.

Some files were missing the appropriate SPDX tags so
fixed it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Update the code to use a flexible array member instead of a pointer in
structure tb10x_pinctrl and use the struct_size() helper:

struct tb10x_pinctrl {
        ...
	struct tb10x_of_pinfunc pinfuncs[];
};

Also, make use of the struct_size() helper instead of an open-coded
version in order to avoid any potential type mistakes.

So, replace the following form:

sizeof(struct tb10x_pinctrl) + of_get_child_count(of_node) * sizeof(struct tb10x_of_pinfunc)

with:

struct_size(state, pinfuncs, of_get_child_count(of_node))

This code was detected with the help of Coccinelle.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add SGPM pinmux to ast2500-pinctrl function and group, to prepare for
supporting SGPIO in AST2500 SoC.
Signed-off-by: Hongwei Zhang <hongweiz@ami.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The ufs_reset pin is expected to be wired to the reset pin of the
primary UFS memory but is pretty much just a general purpose output pinr

Reorder the pins and expose it as gpio 150, so that the UFS driver can
toggle it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add drive strength support for Bitmain BM1880 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Document drive strength settings for Bitmain BM1880 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The i.MX8MM pinfunc head file is located in DT folder, correct it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some files were missing the appropriate SPDX tags so
fixed it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now all Renesas pin control drivers have been converted to use the new
non-GPIO helper macros, SH_PFC_PIN_NAMED() and SH_PFC_PIN_NAMED_CFG()
are no longer used.  Remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Update the SH-Mobile AG5 pin control driver to use the new macros for
describing pins without GPIO functionality.  This replaces the use of
physical pin numbers on the SH-Mobile AG5 SoC (in 34x34 BGA package) by
symbolic enum values, referring to signal names.

Note that the user-visible names of these pins are still based on pin
numbers instead of signal names, to preserve DT backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Update the R-Car E3 pin control driver to use the new macros for
describing pins without GPIO functionality.  This replaces the use of
physical pin numbers on the R-Car E3 SoC (in 25x25 FCBGA package) by
symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Update the R-Car M3-N pin control driver to use the new macros for
describing pins without GPIO functionality.  This replaces the use of
physical pin numbers on the R-Car M3-N SiP (in 39x39 BGA package) by
symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Update the R-Car M3-W pin control driver to use the new macros for
describing pins without GPIO functionality.  This replaces the use of
physical pin numbers on the R-Car M3-W SiP (in 39x39 BGA package) by
symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Update the R-Car H3 ES2.0 and later pin control driver to use the new
macros for describing pins without GPIO functionality.  This replaces
the use of physical pin numbers on the R-Car H3 ES2.0 SiP (in 39x39
BGA package) by symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Update the R-Car H3 ES1.x pin control driver to use the new macros for
describing pins without GPIO functionality.  This replaces the use of
physical pin numbers on the R-Car H3 ES1.x SiP (in 39x39 BGA package) by
symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Update the R-Car H2 pin control driver to use the new macros for
describing pins without GPIO functionality.  This replaces the use of
physical pin numbers on the R-Car H2 SoC (in 31x31 FCBGA package) by
symbolic enum values, referring to signal names.

Note that the user-visible names of these pins are still based on pin
numbers instead of signal names, to preserve DT backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Update the R-Car M1A pin control driver to use the new macros for
describing pins without GPIO functionality.  This replaces the use of
physical pin numbers on the R-Car M1A SoC (in 25x25 FCBGA package) by
symbolic enum values, referring to signal names.

Note that the user-visible names of these pins are still based on pin
numbers instead of signal names, to preserve DT backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Update the EMMA Mobile EV2 pin control driver to use the new macros for
describing pins without GPIO functionality.  This replaces the use of
physical pin numbers on the EMMA Mobile EV2 SoC (in 23x23 BGA package)
by symbolic enum values, referring to signal names.

Note that the user-visible names of these pins are still based on pin
numbers instead of signal names, to preserve DT backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Add new macros for describing pins without GPIO functionality:
  - NOGP_ALL() expands to a list of PIN_id values, to be used for
    generating symbolic enum values,
  - PINMUX_NOGP_ALL() expands to a list of sh_pfc_pin entries, to
    list all pins and their capabilities.
Both macros depend on an SoC-specific CPU_ALL_NOGP() macro, to be
provided by each individual SoC pin control driver.

The new macros offer two advantages over the existing SH_PFC_PIN_NAMED()
and SH_PFC_PIN_NAMED_CFG() macros:
  1. They do not rely on PIN_NUMBER() macros and physical pin numbering,
     hence do not suffer from pin numbering confusion among different
     SoC/SiP packages.
  2. They are similar in spirit to the existing scheme for handling pins
     with GPIO functionality.

Note that internal to the driver, non-GPIO pins use a sequential
numbering scheme which starts after the highest GPIO pin number in use.
This value is calculated automatically, using two new helper macros, for
systems with either 32-port bank (GP port style) or linear (PORT style)
pin space.  Sample expansion:

    GP_LAST = sizeof(union {
	char dummy[0] __attribute__((deprecated, deprecated));
	char GP_0_0[(0 * 32) + 0] __attribute__((deprecated, deprecated));
	char GP_0_1[(0 * 32) + 1] __attribute__((deprecated, deprecated));
	...
	char GP_7_3[(7 * 32) + 3] __attribute__((deprecated, deprecated));
    })
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

drivers/pinctrl/bcm/pinctrl-bcm2835.c: In function bcm2835_pctl_dt_node_to_map:
drivers/pinctrl/bcm/pinctrl-bcm2835.c:720:8: error: implicit declaration of function pinconf_generic_dt_node_to_map_all;
drivers/pinctrl/bcm/pinctrl-bcm2835.c: In function bcm2835_pinctrl_probe:
drivers/pinctrl/bcm/pinctrl-bcm2835.c:1022:15: error: struct gpio_chip has no member named of_node
  pc->gpio_chip.of_node = np;
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 0de70495 ("pinctrl: bcm2835: Add support for generic pinctrl binding")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Using STM32 as guinea pig after Alex's initial positive
test to see if this is something we should encourage
in general and make default behaviour.

Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc:  Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Setting this up will configure wake from suspend properly,
and wake only for the interrupts that are setup in wake_mask,
not all interrupts.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl variants that include pinctrl-paris.h (and not
pinctrl-mtk-common.h) also need to use pm_ops to setup
wake mask properly, so copy over the pm_ops from common
to paris variant.

It is not easy to merge the 2 copies (or move
mtk_eint_suspend/resume to mtk-eint.c), as we need to
dereference pctrl->eint, and struct mtk_pinctrl *pctl has a
different structure definition for v1 and v2 (which is
what paris variant uses).
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>