- 25 Nov, 2016 3 commits
-
-
Prameela Rani Garnepudi authored
RSI 9113 device supports single antenna for tx and rx. Support for using external is added. This can be configured from user space using iw. Signed-off-by:
Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Prameela Rani Garnepudi authored
TX power can be configured from iwconfig, iw or from mac80211 when regulatory changes are done. Hence support for configuring tx power to device is added using the RADIO_PARAMS_UPDATE command frame. Signed-off-by:
-
Prameela Rani Garnepudi authored
Filtering rx frames after connection in station mode avoids the overhead of processing un-necessary frames. Hence rx filter frame is added which can be configured to device at suitable times. Signed-off-by:
-
- 23 Nov, 2016 12 commits
-
-
Stanislaw Gruszka authored
Sending frames in CCK rates on HT can cause performance problems. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Stanislaw Gruszka authored
Use RTS/CTS protection for TXOP on all rates modes as default and disable CCK rates (this cause performance problems). Signed-off-by:
-
Stanislaw Gruszka authored
Change default to RTS/CTS protection. This has a cost of transmitting one more control frame (RTS) however protect us from traffic from hidden node. On station mode will use CTS-to-self if AP will configure that for the network. Signed-off-by:
-
Stanislaw Gruszka authored
Those TX_SW_CFG1 values are used in vendor driver. Signed-off-by:
-
Stanislaw Gruszka authored
Initialize AUTO_RSP_CFG register to similar value as vendor driver does. Do not set BAC_ACK_POLICY based on short preamble setting, those are unrelated. Signed-off-by:
-
Stanislaw Gruszka authored
We already initlized WPDMA_GLO_CFG_WP_DMA_BURST_SIZE to 3 on rt2800_init_registers() for USB devices. For PCI devices we will use HW default setting, which is 2, so patch does not change behaviour on PCI devices. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
We should not reset USB_DMA_CFG on rt2800usb_init_registers() as this function is called indirectly from rt2800_enable_radio(). If we do so, we wipe out USB_DMA_CFG settings from rt2800usb_enable_radio(). Signed-off-by:
-
Stanislaw Gruszka authored
We should only set IEEE80211_HT_MCS_TX_RX_DIF when TX and RX MCS sets are not equal, i.e. when number of tx streams is different than number of RX streams. Signed-off-by:
-
Wright Feng authored
Firmware doesn't update beacon/Probe Response vendor IEs correctly when bss is down, so we move brcmf_config_ap_mgmt_ie after BSS up. And host driver should clear IEs when AP stopped so that the IEs in host side will be synced with in firmware side. Signed-off-by:
Wright Feng <wright.feng@cypress.com> Signed-off-by:
-
Vishal Thanki authored
In device removal routine, usage of "#ifdef CONFIG_RT2X00_LIB_USB" will not cover the case when it is configured as module. This will omit the entire if-block which does cleanup of URBs and cancellation of pending work. Changing the #ifdef to #if IS_ENABLED() to fix it. Signed-off-by:
Vishal Thanki <vishalthanki@gmail.com> Acked-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for 4.10. Major changes: ath9k * add device tree bindings * switch to use mac80211 intermediate software queues to reduce latency and fix bufferbloat
-
- 19 Nov, 2016 15 commits
-
-
Brian Norris authored
It should never be NULL here, and to think otherwise makes things confusing. Signed-off-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
-
Brian Norris authored
These are never NULL, so stop making people think they might be. I don't change this for SDIO because SDIO has a racy card-reset handler that reallocates this struct. I'd rather not touch that mess right now. Signed-off-by:
Xinming Hu <huxm@marvell.com> Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Brian Norris authored
sdio_func is retrieved via container_of() and should never be NULL. Checking for NULL just makes the logic more confusing than necessary. Stop doing that. Signed-off-by:
-
Brian Norris authored
SDIO and PCIe drivers handle this. Let's imitate it. Signed-off-by:
-
Xinming Hu authored
card->adapter gets initialized in mwifiex_register_dev(). As it's not cleared in mwifiex_unregister_dev(), we may end up accessing the memory which is already free in below scenario. Scenario: Driver initialization is failed due to incorrect firmware or some other reason. Meanwhile device reboot/unload occurs. This is safe, now that we've properly synchronized suspend() and remove() with the FW initialization thread; now that code can simply check for 'card->adapter == NULL' and exit safely. Signed-off-by:
-
Brian Norris authored
Signed-off-by:
-
Brian Norris authored
The device core will not allow suspend() to race with remove(). Signed-off-by:
-
Amitkumar Karwar authored
to_pci_dev() would just do struct offset arithmetic on struct device to get 'pdev' pointer. We never get NULL pdev pointer. Signed-off-by:
-
Brian Norris authored
It's possible for the FW init sequence to fail, which will trigger a device cleanup sequence in mwifiex_fw_dpc(). This sequence can race with device suspend() or remove() (e.g., reboot or unbind), and can trigger use-after-free issues. Currently, this driver attempts (poorly) to synchronize remove() using a semaphore, but it doesn't protect some of the critical sections properly. Particularly, we grab a pointer to the adapter struct (card->adapter) without checking if it's being freed or not. We later do a NULL check on the adapter, but that doesn't work if the adapter was freed. Also note that the PCIe interface driver doesn't ever set card->adapter to NULL, so even if we get the synchronization right, we still might try to redo the cleanup in ->remove(), even if the FW init failure sequence already did it. This patch replaces the static semaphore with a per-device completion struct, and uses that completion to synchronize the remove() thread with the mwifiex_fw_dpc(). A future patch will utilize this completion to synchronize the suspend() thread as well. Signed-off-by:
-
Shengzhen Li authored
Power save handshake with firmware might be blocked by on-going data transfer. this patch check the PS status in main process and complete previous blocked PS handshake. this patch also remove redudant check before call mwifiex_check_ps_cond function. Signed-off-by:
Cathy Luo <cluo@marvell.com> Signed-off-by:
Shengzhen Li <szli@marvell.com> Tested-by:
-
Shengzhen Li authored
We may get SLEEP event from firmware even if TXDone interrupt for last Tx packet is still pending. In this case, we may end up accessing PCIe memory for handling TXDone after power save handshake is completed. This causes kernel crash with external abort. This patch will only allow downloading sleep confirm when no tx done interrupt is pending in the hardware. Signed-off-by:
-
Rajat Jain authored
Commit ce4f6f0c ("mwifiex: add platform specific wakeup interrupt support") added WoWLAN feature only for sdio. This patch moves that code to the common module so that all the interface drivers can use it for free. It enables pcie and sdio for its use currently. Signed-off-by:
Rajat Jain <rajatja@google.com> Signed-off-by:
-
Rajat Jain authored
Introduce function mwifiex_probe_of() to parse common properties. Interface drivers get to decide whether or not the device tree node was a valid one (depending on the compatible property), Lets fill "adapter->dt_node" in mwifiex_add_card(). The function mwifiex_probe_of() is currently only a place holder with the next patch adding content to it. Signed-off-by:
-
Rajat Jain authored
Today all the interface drivers (usb/pcie/sdio) assign the adapter->dev in the register_dev() callback, although they have this piece of info well before hand. This patch makes the device structure available for mwifiex right at the beginning, so that it can be used for early initialization if needed. This is needed for subsequent patches in this patchset that intend to unify and consolidate some of the code that would otherwise have to be duplicated among the interface drivers (sdio, pcie, usb). Signed-off-by:
-
Xinming Hu authored
This patch derives device tree node from pcie bus layer framework. Device tree bindings file has been renamed(marvell-sd8xxx.txt -> marvell-8xxx.txt) to accommodate PCIe changes. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
- 18 Nov, 2016 3 commits
-
-
Brian Norris authored
The cleanup_if() callback is the inverse of init_if(). We allocate our 'card' interface structure in the probe() function, but we free it in cleanup_if(). That gives a few problems: (a) we leak this memory if probe() fails before we reach init_if() (b) we can't safely utilize 'card' after cleanup_if() -- namely, in remove() or suspend(), both of which might race with the cleanup paths in our asynchronous FW initialization path Solution: just use devm_kzalloc(), which will free this structure properly when the device is removed -- and drop the set_drvdata(..., NULL), since the driver core does this for us. This also removes the temptation to use drvdata == NULL as a hack for checking if the device has been "cleaned up." I *do* leave the set_drvdata(..., NULL) for the hacky SDIO mwifiex_recreate_adapter(), since the device core won't be able to clear that one for us. Signed-off-by: -
Amitkumar Karwar authored
Firmware may reject calibration data from host for certain OTP settings. In that case, we should continue initialisation ignoring the failure. Signed-off-by:
-
Shengzhen Li authored
This patch adds power save parameters(hs_wake_interval and hs_inactivity_timeout) in host sleep cfg cmd. Signed-off-by:
-
- 17 Nov, 2016 7 commits
-
-
Ricky Liang authored
kmemleak reports memory leak in mwifiex_save_hidden_ssid_channels(): unreferenced object 0xffffffc0a2914780 (size 192): comm "ksdioirqd/mmc2", pid 2004, jiffies 4307182506 (age 820.684s) hex dump (first 32 bytes): 00 06 47 49 4e 2d 32 67 01 03 c8 60 6c 03 01 40 ..GIN-2g...`l..@ 07 10 54 57 20 34 04 1e 64 05 24 84 03 24 95 04 ..TW 4..d.$..$.. backtrace: [<ffffffc0003375f4>] create_object+0x164/0x2b4 [<ffffffc0008e3530>] kmemleak_alloc+0x50/0x88 [<ffffffc000335120>] __kmalloc_track_caller+0x1bc/0x264 [<ffffffc00030899c>] kmemdup+0x38/0x64 [<ffffffbffc2311cc>] mwifiex_fill_new_bss_desc+0x3c/0x130 [mwifiex] [<ffffffbffc22ee9c>] mwifiex_save_curr_bcn+0x4ec/0x640 [mwifiex] [<ffffffbffc22f45c>] mwifiex_handle_event_ext_scan_report+0x1d4/0x268 [mwifiex] [<ffffffbffc2375d0>] mwifiex_process_sta_event+0x378/0x898 [mwifiex] [<ffffffbffc224dc8>] mwifiex_process_event+0x1a8/0x1e8 [mwifiex] [<ffffffbffc2228f0>] mwifiex_main_process+0x258/0x534 [mwifiex] [<ffffffbffc258858>] 0xffffffbffc258858 [<ffffffc00071ee90>] process_sdio_pending_irqs+0xf8/0x160 [<ffffffc00071efdc>] sdio_irq_thread+0x9c/0x1a4 [<ffffffc000240d08>] kthread+0xf4/0x100 [<ffffffc0002043fc>] ret_from_fork+0xc/0x50 [<ffffffffffffffff>] 0xffffffffffffffff Signed-off-by:Ricky Liang <jcliang@chromium.org> Acked-by:
-
Larry Finger authored
When there is a CRC error in the SPROM read from the device, the code attempts to handle a fallback SPROM. When this also fails, the driver returns zero rather than an error code. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by:
-
Wei Yongjun authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled, spin_lock_irqsave() make sure always in irq disable context. So the kfree_skb() should be replaced with dev_kfree_skb_irq(). This is detected by Coccinelle semantic patch. Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
-
Arnd Bergmann authored
On x86, the cw1200 driver produces a rather silly warning about the possible use of the 'ret' variable without an initialization presumably after being confused by the architecture specific definition of WARN_ON: drivers/net/wireless/st/cw1200/wsm.c: In function ‘wsm_handle_rx’: drivers/net/wireless/st/cw1200/wsm.c:1457:9: error: ‘ret’ may be used uninitialized in this function [-Werror=maybe-uninitialized] We have already checked that 'count' is larger than 0 here, so we know that 'ret' is initialized. Changing the 'for' loop into do/while also makes this clear to the compiler. Suggested-by:
David Laight <David.Laight@ACULAB.COM> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Arnd Bergmann authored
The hostap_80211_rx() function is supposed to set up the mac addresses for four possible cases, based on two bits of input data. For some reason, gcc decides that it's possible that none of the these four cases apply and the addresses remain uninitialized: drivers/net/wireless/intersil/hostap/hostap_80211_rx.c: In function ‘hostap_80211_rx’: arch/x86/include/asm/string_32.h:77:14: warning: ‘src’ may be used uninitialized in this function [-Wmaybe-uninitialized] drivers/net/wireless/intel/ipw2x00/libipw_rx.c: In function ‘libipw_rx’: arch/x86/include/asm/string_32.h:77:14: error: ‘dst’ may be used uninitialized in this function [-Werror=maybe-uninitialized] arch/x86/include/asm/string_32.h:78:22: error: ‘*((void *)&dst+4)’ may be used uninitialized in this function [-Werror=maybe-uninitialized] This warning is clearly nonsense, but changing the last case into 'default' makes it obvious to the compiler too, which avoids the warning and probably leads to better object code too. The same code is duplicated several times in the kernel, so this patch uses the same workaround for all copies. The exact configuration was hit only very rarely in randconfig builds and I only saw it in three drivers, but I assume that all of them are potentially affected, and it's better to keep the code consistent. Signed-off-by:
-
Jiri Slaby authored
gcc 7 complains: drivers/net/wireless/intersil/p54/fwio.c: In function 'p54_scan': drivers/net/wireless/intersil/p54/fwio.c:491:4: warning: 'memset' used with length equal to number of elements without multiplication by element size [-Wmemset-elt-size] Fix that by passing the correct size to memset. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Acked-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
-
Rafał Miłecki authored
This simplifies debugging. Format %s (%u) comes from similar debugging message in brcmf_fweh_event_worker. Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Signed-off-by:
-
