- 29 Sep, 2006 2 commits
-
-
Jeff Garzik authored
Update copyright year, fix minor stuff 'make xmldocs' complains about. Signed-off-by:Jeff Garzik <jeff@garzik.org>
-
Jeff Garzik authored
* Use PCI_VDEVICE() macro * const-ify pci_device_id table * standardize list terminator as "{ }" * convert spaces to tab in pci_driver struct (Alan-ism) * various minor whitespace cleanups Signed-off-by:
-
- 28 Sep, 2006 4 commits
-
-
Jeff Garzik authored
We have the info stored in an ata_busy_sleep() variable, so might as well print it, and provide some additional diagnostic info. Signed-off-by: -
Jeff Garzik authored
Don't write the same code twice, in two different functions, when they both call the same initialization function, with the same private_data pointer info. Also, note a bug found with a FIXME. Signed-off-by: -
Jeff Garzik authored
* Replace needless 'n_ports > 2' check with a simple BUG_ON(). No existing driver ever wants more than 2 ports. * Delete ATA_FLAG_NO_LEGACY check. No current driver uses ata_pci_init_one(), that sets this flag. * Move PCI_CLASS_PROG register read below pci_enable_device() * Handle ata_device_add() failure Signed-off-by: -
Jeff Garzik authored
Signed-off-by:
-
- 27 Sep, 2006 34 commits
-
-
Jeff Garzik authored
-
Dave Jones authored
ata_device_add fails, calls ata_host_remove with pointers to unitialized memory. Signed-off-by:
Dave Jones <davej@redhat.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
-
Linus Torvalds authored
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits) [PATCH] bonding: update version number [PATCH] git-netdev-all: pc300_tty build fix [PATCH] Make PC300 WAN driver compile again [PATCH] Modularize generic HDLC [PATCH] more s2io __iomem annotations [PATCH] restore __iomem annotations in e1000 [PATCH] 64bit bugs in s2io [PATCH] bonding: Fix primary selection error at enslavement time [PATCH] bonding: Don't mangle LACPDUs [PATCH] bonding: Validate probe replies in ARP monitor [PATCH] bonding: Don't release slaves when master is admin down [PATCH] bonding: Add priv_flag to avoid event mishandling [PATCH] bonding: Handle large hard_header_len [PATCH] bonding: Remove unneeded NULL test [PATCH] bonding: Format fix in seq_printf call [PATCH] bonding: Convert delay value from s16 to int [PATCH] bonding: Allow bonding to enslave a 10 Gig adapter Delete unused drivers/net/gt64240eth.h [PATCH] skge: fiber support [PATCH] fix possible NULL ptr deref in forcedeth ...
-
Linus Torvalds authored
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: [libata] Don't use old-EH ->eng_timeout() hook when not needed [libata] sata_mv: fix oops by filling in missing hook [libata] One more s/15/ATA_SECONDARY_IRQ/ substitution [libata] pata_serverworks: fill in ->irq_clear hook [PATCH] pata_serverworks: correct PCI ID in cable detection table [PATCH] libata-sff: use our IRQ defines [PATCH] libata-eh: Remove layering violation and duplication when handling absent ports [PATCH] libata: tighten rules for legacy dependancies [PATCH] libata: refuse to register IRQless ports
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (129 commits) [PATCH] USB Storage: fix Rio Karma eject support build error USB: Airprime driver improvements to allow full speed EvDO transfers USB: remove OTG build warning USB: EHCI update VIA workaround USB: force root hub resume after power loss USB: ohci_usb can oops on shutdown USB: Dealias -110 code (more complete) USB: Remove unneeded void * casts in core files USB: u132-hcd: host controller driver for ELAN U132 adapter USB: ftdi-elan: client driver for ELAN Uxxx adapters usb serial: support Alcor Micro Corp. USB 2.0 TO RS-232 through pl2303 driver USB: Moschip 7840 USB-Serial Driver USB: add PlayStation 2 Trance Vibrator driver USB: Add ADU support for Ontrak ADU devices aircable: fix printk format warnings Add AIRcable USB Bluetooth Dongle Driver cypress_m8: implement graceful failure handling cypress_m8: improve control endpoint error handling cypress_m8: use usb_fill_int_urb where appropriate cypress_m8: use appropriate URB polling interval ...
-
Andi Kleen authored
The new code does clobber the result early, so make sure to tell gcc to not put it into the same register as a input argument Signed-off-by:
Andi Kleen <ak@suse.de> Cc: Andrew Morton <akpm@osdl.org> Acked-by:
Kyle McMartin <kyle@parisc-linux.org> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Jay Vosburgh authored
I neglected to properly update the version number in the recent patch series; this sets it to something reasonable. Signed-off-by:
Jay Vosburgh <fubar@us.ibm.com> Signed-off-by:
-
Andrew Morton authored
In file included from drivers/net/wan/pc300_tty.c:59: drivers/net/wan/pc300.h:335: error: field 'pppdev' has incomplete type Cc: Krzysztof Halasa <khc@pm.waw.pl> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by:
-
Andrew Morton authored
In file included from drivers/usb/storage/usb.c:180: drivers/usb/storage/unusual_devs.h:221: error: 'US_PR_KARMA' undeclared here (not in a function) drivers/usb/storage/unusual_devs.h:221: error: 'rio_karma_init' undeclared here (not in a function) Cc: Keith Bennett <keith@mcs.st-and.ac.uk> Acked-by:
Bob Copeland <me@bobcopeland.com> Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Andy Gay authored
Adapted from an earlier patch by Greg KH <gregkh@suse.de>. That patch added multiple read urbs and larger transfer buffers to allow data transfers at full EvDO speed. This version includes additional device IDs and fixes a memory leak in the transfer buffer allocation. Some (maybe all?) of the supported devices present multiple bulk endpoints, the additional EPs can be used for control and status functions, This version allocates 3 EPs by default, that can be changed using the 'endpoints' module parameter. Tested with Sierra Wireless EM5625 and MC5720 embedded modules. Device ID (0x0c88, 0x17da) for the Kyocera Wireless KPC650/Passport was added but is not yet tested. From: Andy Gay <andy@andynet.net> Cc: Kevin Lloyd <linux@sierrawireless.com> Signed-off-by: -
David Brownell authored
Somewhere along the line, a variable in a USB-OTG codepath stopped being used; this removes the relevant compiler warning. Signed-off-by:
David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
David Brownell authored
This revamps handling of the hardware "async advance" IRQ, and its watchdog timer. Basically it dis-entangles that important timeout from the others, simplifying the associated state and code to make it more robust. This reportedly improves behavior of EHCI on some systems with VIA chips, and AFAIK won't affect non-VIA hardware. VIA systems need this code to recover from silcon bugs whereby the "async advance" IRQ isn't issued. Signed-off-by:
-
Alan Stern authored
This patch(as785) forces the PM core to resume a root hub after a power loss during system sleep. If the root hub had been suspended before the system sleep then normally the PM core would not resume it afterward. Without this resume, various sorts of wakeup events (like port change events) can get lost. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Pete Zaitcev authored
When ohci-hcd is shutting down (for rmmod or PC-card removal), there is a window when the device is shut down, HC communication area (->hcca) is freed, but the core has not called "free_irq" yet. If another device triggers a shared interrupt in this window, we oops when trying to access the freed ->hcca. This patch removes the window by calling free_irq before ->hcca is freed. The patch is tested at the PC hotplug test rig at Stratus, and with rmmod by Rafael Wysocki. Signed-off-by:
Pete Zaitcev <zaitcev@redhat.com> Signed-off-by:
-
Pete Zaitcev authored
The purpose of this patch is to split off the case when a device does not reply on the lower level (which is reported by HC hardware), and a case when the device accepted the request, but does not reply at upper level. This redefinition allows to diagnose issues easier, without asking the user if the -110 happened "immediately". The usbmon splits such cases already thanks to its timestamp, but it's not always available. I adjusted all drivers which I found affected (by searching for "urb"). Out of tree drivers may suffer a little bit, but I do not expect much breakage. At worst they may print a few messages. Signed-off-by:
-
Tobias Klauser authored
The patch removes unneeded casts for the following (void *) pointers: - struct file: private - struct urb: context - struct usb_bus: hcpriv - return value of kmalloc() The patch also contains some whitespace cleanup in the relevant areas. Signed-off-by:
Tobias Klauser <tklauser@distanz.ch> Signed-off-by:
-
Tony Olech authored
This "u132-hcd" module is one half of the "driver" for ELAN's U132 which is a USB to CardBus OHCI controller adapter. This module needs the "ftdi-elan" module in order to communicate to CardBus OHCI controller inserted into the U132 adapter. When the "ftdi-elan" module detects a supported CardBus OHCI controller in the U132 adapter it loads this "u132-hcd" module. Upon a successful device probe() the single workqueue is started up which does all the processing of commands from the USB core that implement the host controller. The workqueue maintains the urb queues and issues commands via the functions exported by the "ftdi-elan" module. Each such command will result in a callback. Note that the "ftdi-elan" module is a USB client driver. Note that this "u132-hcd" module is a (cut-down OHCI) host controller. Thus we have a topology with the parent of a host controller being a USB client! This really stresses the USB subsystem semaphore/mutex handling in the module removal. Signed-off-by:
Tony Olech <tony.olech@elandigitalsystems.com> Signed-off-by:
-
Tony Olech authored
This "ftdi-elan" module is one half of the "driver" for ELAN's Uxxx series adapters which are USB to PCMCIA CardBus adapters. Currently only the U132 adapter is available and it's module is called "u132-hcd". When the USB hot plug subsystem detects a Uxxx series adapter it should load this module. Upon a successful device probe() the jtag device file interface is created and the status workqueue started up. The jtag device file interface exists for the purpose of updating the firmware in the Uxxx series adapter, but as yet it had never been used. The status workqueue initializes the Uxxx and then sits there polling the Uxxx until a supported PCMCIA CardBus device is detected it will start the command and respond workqueues and then load the module that handles the device. This will initially be only the u132-hcd module. The status workqueue then just polls the Uxxx looking for card ejects. The command and respond workqueues implement a command sequencer for communicating with the firmware on the other side of the FTDI chip in the Uxxx. This "ftdi-elan" module exports some functions to interface with the sequencer. Note that this module is a USB client driver. Note that the "u132-hcd" module is a (cut-down OHCI) host controller. Thus we have a topology with the parent of a host controller being a USB client! This really stresses the USB subsystem semaphore/mutex handling in the module removal. Signed-off-by:
-
Johannes Steingraeber authored
Patch to add support for Alcor Micro Corp. USB 2.0 TO RS-232 converter. This patch adds VID and PID to pl2303.[ch], adds it to the "HORRIBLE HACK FOR PL2303" in usb-serial.c and also prevents cdc-acm to claim driving this device by blacklisting it in hid-core. Signed-off-by:
Johannes Steingraeber <Jo_Stein@web.de> Signed-off-by:
-
Paul B Schroeder authored
Signed-off-by:
Paul B Schroeder <pschroeder@uplogix.com> Signed-off-by:
-
Sam Hocevar authored
This patch is a driver for the PlayStation 2 specific Trance Vibrator device. The only thing that device can do is vibrate at various speeds. Signed-off-by:
Sam Hocevar <sam@zoy.org> Cc: Pete Zaitcev <zaitcev@redhat.com> Cc: Luiz Fernando N. Capitulino" <lcapitulino@mandriva.com.br> Signed-off-by:
-
Steven Haigh authored
This patch adds support for Ontrak ADU USB devices. Fixed for printk issues by Randy Dunlap <rdunlap@xenotime.net> Signed-off-by:
Steven Haigh <netwiz@crc.id.au> Signed-off-by:
-
Randy Dunlap authored
Fix printk format warnings: drivers/usb/serial/aircable.c:221: warning: format ‘%Zd’ expects type ‘signed size_t’, but argument 4 has type ‘int’ drivers/usb/serial/aircable.c:283: warning: format ‘%Zd’ expects type ‘signed size_t’, but argument 4 has type ‘int’ Signed-off-by:
Randy Dunlap <rdunlap@xenotime.net> Signed-off-by:
-
Manuel Francisco Naranjo authored
Add driver for AIRcable USB Bluetooth dongle. Signed-off-by:
Naranjo, Manuel Francisco <naranjo.manuel@gmail.com> Signed-off-by:
-
Mike Isely authored
When receiving a fatal error from the USB core, e.g. EILSEQ (which can happen if the polling interval is too short), fail gracefully. Previously the driver would fill the log with useless error messages or (more alarmingly) silently spin forever trying to write updated control information to the device. This change implements a new flag which if cleared indicates that the driver has failed. The flag will be set on initialization, cleared on fatal errors, and anything else that touches the USB port in the driver will abort if the flag is clear. When the flag is cleared, a message will be logged indicating that the driver has failed. Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
-
Mike Isely authored
Fix usb core function error return checks to look for negative errno values, not positive errno values. This bug had rendered those checks useless. Also remove attempted error recovery on control endpoints for EPIPE - with control endpoints EPIPE does not indicate a halted endpoint so trying to recover with usb_clear_halt() is not the correct action. Signed-off-by:
-
Mike Isely authored
Rather than directly filling in URB fields, it's safer to use usb_fill_int_urb(). This improves robustness of the driver; URB changes in the future will not go uninitialized here. That point not withstanding, this driver should at least be self-consistent. Either use usb_fill_int_urb() everywhere or don't bother with it all. Signed-off-by:
-
Mike Isely authored
The polling interval for the device can't always be 1msec. If it is too quick, the device can fail causing a fatal (to the driver) EILSEQ error from the USB core. The actual correct value is reported by the device as part of its configuration data, so use that value as the default. On a DeLorme Earthmate for example, the device reports that it wants a 6msec interval. As part of this fix, the "interval" module option has been fixed as well; the device's default can be overridden by specifying interval=<value> as a module option. Signed-off-by:
-
Greg Kroah-Hartman authored
Signed-off-by: -
Greg Kroah-Hartman authored
Signed-off-by: -
Greg Kroah-Hartman authored
Signed-off-by: -
Greg Kroah-Hartman authored
Signed-off-by: -
Greg Kroah-Hartman authored
Signed-off-by: -
Greg Kroah-Hartman authored
Signed-off-by:
-
