After each filesystem block (as represented by a buffer_head) has been
read from disk by block_read_full_folio(), verify it if needed.  The
verification is done on the fsverity_read_workqueue.  Also allow reads
of verity metadata past i_size, as required by ext4.

This is needed to support fsverity on ext4 filesystems where the
filesystem block size is less than the page size.

The new code is compiled away when CONFIG_FS_VERITY=n.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20221223203638.41293-11-ebiggers@kernel.org

Now that the implementation of FS_IOC_ENABLE_VERITY has changed to not
involve reading back Merkle tree blocks that were previously written,
there is no need for f2fs_readpage_limit() to allow for this case.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20221223203638.41293-10-ebiggers@kernel.org

Now that the implementation of FS_IOC_ENABLE_VERITY has changed to not
involve reading back Merkle tree blocks that were previously written,
there is no need for ext4_readpage_limit() to allow for this case.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20221223203638.41293-9-ebiggers@kernel.org

Make FS_IOC_ENABLE_VERITY support values of
fsverity_enable_arg::block_size other than PAGE_SIZE.

To make this possible, rework build_merkle_tree(), which was reading
data and hash pages from the file and assuming that they were the same
thing as "blocks".

For reading the data blocks, just replace the direct pagecache access
with __kernel_read(), to naturally read one block at a time.

(A disadvantage of the above is that we lose the two optimizations of
hashing the pagecache pages in-place and forcing the maximum readahead.
That shouldn't be very important, though.)

The hash block reads are a bit more difficult to handle, as the only way
to do them is through fsverity_operations::read_merkle_tree_page().

Instead, let's switch to the single-pass tree construction algorithm
that fsverity-utils uses.  This eliminates the need to read back any
hash blocks while the tree is being built, at the small cost of an extra
block-sized memory buffer per Merkle tree level.  This is probably what
I should have done originally.

Taken together, the above two changes result in page-size independent
code that is also a bit simpler than what we had before.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Andrey Albershteyn <aalbersh@redhat.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20221223203638.41293-8-ebiggers@kernel.org

Add support for verifying data from verity files whose Merkle tree block
size is less than the page size.  The main use case for this is to allow
a single Merkle tree block size to be used across all systems, so that
only one set of fsverity file digests and signatures is needed.

To do this, eliminate various assumptions that the Merkle tree block
size and the page size are the same:

- Make fsverity_verify_page() a wrapper around a new function
  fsverity_verify_blocks() which verifies one or more blocks in a page.

- When a Merkle tree block is needed, get the corresponding page and
  only verify and use the needed portion.  (The Merkle tree continues to
  be read and cached in page-sized chunks; that doesn't need to change.)

- When the Merkle tree block size and page size differ, use a bitmap
  fsverity_info::hash_block_verified to keep track of which Merkle tree
  blocks have been verified, as PageChecked cannot be used directly.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Andrey Albershteyn <aalbersh@redhat.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20221223203638.41293-7-ebiggers@kernel.org

In preparation for allowing the Merkle tree block size to differ from
PAGE_SIZE, replace fsverity_hash_page() with fsverity_hash_block().  The
new function is similar to the old one, but it operates on the block at
the given offset in the page instead of on the full page.

(For now, all callers still pass a full page.)
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Andrey Albershteyn <aalbersh@redhat.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20221223203638.41293-6-ebiggers@kernel.org

Currently, there is an implementation limit where files can't have more
than 8 Merkle tree levels.  With SHA-256 and 4K blocks, this limit is
never reached, since a file would need to be larger than 2**64 bytes to
need 9 levels.  However, with SHA-512, 9 levels are needed for files
larger than about 1.15 EB, which is possible on btrfs.  Therefore, this
limit technically became reachable when btrfs added fsverity support.

Meanwhile, support for merkle_tree_block_size < PAGE_SIZE will introduce
another implementation limit on file size, resulting from the use of an
in-memory bitmap to track which Merkle tree blocks have been verified.

In any case, currently FS_IOC_ENABLE_VERITY fails with EINVAL when the
file is too large.  This is undocumented, and also ambiguous since
EINVAL can mean other things too.  Let's change the error code to EFBIG,
which is much clearer, and document it.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Andrey Albershteyn <aalbersh@redhat.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20221223203638.41293-5-ebiggers@kernel.org

Add log_digestsize to struct merkle_tree_params so that it can be used
in verify.c.  Also save memory by using u8 for all the log_* fields.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Andrey Albershteyn <aalbersh@redhat.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20221223203638.41293-4-ebiggers@kernel.org

First, calculate max_ra_pages more efficiently by using the bio size.

Second, calculate the number of readahead pages from the hash page
index, instead of calculating it ahead of time using the data page
index.  This ends up being a bit simpler, especially since level 0 is
last in the tree, so we can just limit the readahead to the tree size.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Andrey Albershteyn <aalbersh@redhat.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20221223203638.41293-3-ebiggers@kernel.org

fs/verity/ isn't consistent with whether Merkle tree block indices are
'unsigned long' or 'u64'.  There's no real point to using u64 for them,
though, since (a) a Merkle tree with over ULONG_MAX blocks would only be
needed for a file larger than MAX_LFS_FILESIZE, and (b) for reads, the
status of all Merkle tree blocks has to be tracked in memory.

Therefore, let's make things a bit more efficient on 32-bit systems by
using 'unsigned long[]' for merkle_tree_params::level_start, instead of
'u64[]'.  Also, to be extra safe, explicitly check that there aren't
more than ULONG_MAX Merkle tree blocks.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Andrey Albershteyn <aalbersh@redhat.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20221223203638.41293-2-ebiggers@kernel.org

I've gotten very little use out of these debug messages, and I'm not
aware of anyone else having used them.

Indeed, sprinkling pr_debug around is not really a best practice these
days, especially for filesystem code.  Tracepoints are used instead.

Let's just remove these and start from a clean slate.

This change does not affect info, warning, and error messages.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20221215060420.60692-1-ebiggers@kernel.org

fsverity_operations::write_merkle_tree_block is passed the index of the
block to write and the log base 2 of the block size.  However, all
implementations of it use these parameters only to calculate the
position and the size of the block, in bytes.

Therefore, make ->write_merkle_tree_block take 'pos' and 'size'
parameters instead of 'index' and 'log_blocksize'.
Suggested-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Link: https://lore.kernel.org/r/20221214224304.145712-5-ebiggers@kernel.org

Make fsverity_cleanup_inode() an inline function that checks for
non-NULL ->i_verity_info, then (if needed) calls
__fsverity_cleanup_inode() to do the real work.  This reduces the
overhead on non-verity files.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Link: https://lore.kernel.org/r/20221214224304.145712-4-ebiggers@kernel.org

Make fsverity_prepare_setattr() an inline function that does the
IS_VERITY() check, then (if needed) calls __fsverity_prepare_setattr()
to do the real work.  This reduces the overhead on non-verity files.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Link: https://lore.kernel.org/r/20221214224304.145712-3-ebiggers@kernel.org

Make fsverity_file_open() an inline function that does the IS_VERITY()
check, then (if needed) calls __fsverity_file_open() to do the real
work.  This reduces the overhead on non-verity files.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Link: https://lore.kernel.org/r/20221214224304.145712-2-ebiggers@kernel.org

Pull perf fixes from Borislav Petkov:

 - Pass only an initialized perf event attribute to the LSM hook

 - Fix a use-after-free on the perf syscall's error path

 - A potential integer overflow fix in amd_core_pmu_init()

 - Fix the cgroup events tracking after the context handling rewrite

 - Return the proper value from the inherit_event() function on error

* tag 'perf_urgent_for_v6.2_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Call LSM hook after copying perf_event_attr
  perf: Fix use-after-free in error path
  perf/x86/amd: fix potential integer overflow on shift of a int
  perf/core: Fix cgroup events tracking
  perf core: Return error pointer if inherit_event() fails to find pmu_ctx

Pull x86 fixes from Borislav Petkov:

 - Two fixes to correct how kprobes handles INT3 now that they're added
   by other functionality like the rethunks and not only kgdb

 - Remove __init section markings of two functions which are referenced
   by a function in the .text section

* tag 'x86_urgent_for_v6.2_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/kprobes: Fix optprobe optimization check with CONFIG_RETHUNK
  x86/kprobes: Fix kprobes instruction boudary check with CONFIG_RETHUNK
  x86/calldepth: Fix incorrect init section references

Pull locking fixes from Borislav Petkov:

 - Prevent the leaking of a debug timer in futex_waitv()

 - A preempt-RT mutex locking fix, adding the proper acquire semantics

* tag 'locking_urgent_for_v6.2_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  futex: Fix futex_waitv() hrtimer debug object leak on kcalloc error
  rtmutex: Add acquire semantics for rtmutex lock acquisition slow path

Pull drm fixes from Daniel Vetter:
 "I'm just back from the mountains, and Dave is out at the beach and
  should be back in a week again. Just i915 fixes and since Rodrigo
  bothered to make the pull last week I figured I should warm up gpg and
  forward this in a nice signed tag as a new years present!

   - i915 fixes for newer platforms

   - i915 locking rework to not give up in vm eviction fallback path too
     early"

* tag 'drm-fixes-2023-01-01' of git://anongit.freedesktop.org/drm/drm:
  drm/i915/dsi: fix MIPI_BKLT_EN_1 native GPIO index
  drm/i915/dsi: add support for ICL+ native MIPI GPIO sequence
  drm/i915/uc: Fix two issues with over-size firmware files
  drm/i915: improve the catch-all evict to handle lock contention
  drm/i915: Remove __maybe_unused from mtl_info
  drm/i915: fix TLB invalidation for Gen12.50 video and compute engines

Merge tag 'drm-intel-fixes-2022-12-30' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

- fix TLB invalidation for DG2 and newer platforms. (Andrzej)
- Remove __maybe_unused from mtl_info (Lucas)
- improve the catch-all evict to handle lock contention (Matt Auld)
- Fix two issues with over-size (GuC/HuC) firmware files (John)
- Fix DSI resume issues on ICL+ (Jani)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Y662ijDHrZCjTFla@intel.com

Merge tag 'kbuild-fixes-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Fix broken BuildID

 - Add srcrpm-pkg to the help message

 - Fix the option order for modpost built with musl libc

 - Fix the build dependency of rpm-pkg for openSUSE

* tag 'kbuild-fixes-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  fixdep: remove unneeded <stdarg.h> inclusion
  kbuild: sort single-targets alphabetically again
  kbuild: rpm-pkg: add libelf-devel as alternative for BuildRequires
  kbuild: Fix running modpost with musl libc
  kbuild: add a missing line for help message
  .gitignore: ignore *.rpm
  arch: fix broken BuildID for arm64 and riscv
  kconfig: Add static text for search information in help menu

Pull ata fix from Damien Le Moal:
 "A single fix to address an issue with wake from suspend with PCS
  adapters, from Adam"

* tag 'ata-6.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
  ata: ahci: Fix PCS quirk application for suspend

Pull ACPI fixes from Rafael Wysocki:
 "These are new ACPI IRQ override quirks, low-power S0 idle (S0ix)
  support adjustments and ACPI backlight handling fixes, mostly for
  platforms using AMD chips.

  Specifics:

   - Add ACPI IRQ override quirks for Asus ExpertBook B2502, Lenovo
     14ALC7, and XMG Core 15 (Hans de Goede, Adrian Freund, Erik
     Schumacher).

   - Adjust ACPI video detection fallback path to prevent
     non-operational ACPI backlight devices from being created on
     systems where the native driver does not detect a suitable panel
     (Mario Limonciello).

   - Fix Apple GMUX backlight detection (Hans de Goede).

   - Add a low-power S0 idle (S0ix) handling quirk for HP Elitebook 865
     and stop using AMD-specific low-power S0 idle code path for systems
     with Rembrandt chips and newer (Mario Limonciello)"

* tag 'acpi-6.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: x86: s2idle: Stop using AMD specific codepath for Rembrandt+
  ACPI: x86: s2idle: Force AMD GUID/_REV 2 on HP Elitebook 865
  ACPI: video: Fix Apple GMUX backlight detection
  ACPI: resource: Add Asus ExpertBook B2502 to Asus quirks
  ACPI: resource: do IRQ override on Lenovo 14ALC7
  ACPI: resource: do IRQ override on XMG Core 15
  ACPI: video: Don't enable fallback path for creating ACPI backlight by default
  drm/amd/display: Report to ACPI video if no panels were found
  ACPI: video: Allow GPU drivers to report no panels

Pull sound fixes from Takashi Iwai:
 "Just a few small fixes:

   - A regression fix for HDMI audio on HD-audio AMD codecs

   - Fixes for LINE6 MIDI handling

   - HD-audio quirk for Dell laptops"

* tag 'sound-6.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/hdmi: Static PCM mapping again with AMD HDMI codecs
  ALSA: hda/realtek: Apply dual codec fixup for Dell Latitude laptops
  ALSA: line6: fix stack overflow in line6_midi_transmit
  ALSA: line6: correct midi status byte when receiving data from podxt

Merge ACPI resource handling quirks and ACPI backlight handling fixes
for 6.2-rc2:

 - Add ACPI IRQ override quirks for Asus ExpertBook B2502, Lenovo
   14ALC7, and XMG Core 15 (Hans de Goede, Adrian Freund,  Erik
   Schumacher).

 - Adjust ACPI video detection fallback path to prevent non-operational
   ACPI backlight devices from being created on systems where the native
   driver does not detect a suitable panel (Mario Limonciello).

 - Fix Apple GMUX backlight detection (Hans de Goede).

* acpi-resource:
  ACPI: resource: Add Asus ExpertBook B2502 to Asus quirks
  ACPI: resource: do IRQ override on Lenovo 14ALC7
  ACPI: resource: do IRQ override on XMG Core 15

* acpi-video:
  ACPI: video: Fix Apple GMUX backlight detection
  ACPI: video: Don't enable fallback path for creating ACPI backlight by default
  drm/amd/display: Report to ACPI video if no panels were found
  ACPI: video: Allow GPU drivers to report no panels

Due to copy-paste fail, MIPI_BKLT_EN_1 would always use PPS index 1,
never 0. Fix the sloppiest commit in recent memory.

Fixes: 963bbdb3 ("drm/i915/dsi: add support for ICL+ native MIPI GPIO sequence")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221220140105.313333-1-jani.nikula@intel.com
(cherry picked from commit a561933c)
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Starting from ICL, the default for MIPI GPIO sequences seems to be using
native GPIOs i.e. GPIOs available in the GPU. These native GPIOs reuse
many pins that quite frankly seem scary to poke based on the VBT
sequences. We pretty much have to trust that the board is configured
such that the relevant HPD, PP_CONTROL and GPIO bits aren't used for
anything else.

MIPI sequence v4 also adds a flag to fall back to non-native sequences.

v5:
- Wrap SHOTPLUG_CTL_DDI modification in spin_lock() in icp_irq_handler()
  too (Ville)
- References instead of Closes issue 6131 because this does not fix everything

v4:
- Wrap SHOTPLUG_CTL_DDI modification in spin_lock_irq() (Ville)

v3:
- Fix -Wbitwise-conditional-parentheses (kernel test robot <lkp@intel.com>)

v2:
- Fix HPD pin output set (impacts GPIOs 0 and 5)
- Fix GPIO data output direction set (impacts GPIOs 4 and 9)
- Reduce register accesses to single intel_de_rwm()

References: https://gitlab.freedesktop.org/drm/intel/-/issues/6131
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221219105955.4014451-1-jani.nikula@intel.com
(cherry picked from commit f087cfe6)
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

This is unneeded since commit 69304379 ("fixdep: use fflush() and
ferror() to ensure successful write to files").
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

This was previously alphabetically sorted. Sort it again.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>

Guoqing Jiang reports that openSUSE cannot compile the kernel rpm due
to "BuildRequires: elfutils-libelf-devel" added by commit 8818039f
("kbuild: add ability to make source rpm buildable using koji").
The relevant package name in openSUSE is libelf-devel.

Add it as an alternative package.

BTW, if it is impossible to solve the build requirement, the final
resort would be:

    $ make RPMOPTS=--nodeps rpm-pkg

This passes --nodeps to the rpmbuild command so it will not verify
build dependencies. This is useful to test rpm builds on non-rpm
system. On Debian/Ubuntu, for example, you can install rpmbuild by
'apt-get install rpm'.

NOTE1:
  Likewise, it is possible to bypass the build dependency check for
  debian package builds:

    $ make DPKG_FLAGS=-d deb-pkg

NOTE2:
  The 'or' operator is supported since RPM 4.13. So, old distros such
  as CentOS 7 will break. I suggest installing newer rpmbuild in such
  cases.

Link: https://lore.kernel.org/linux-kbuild/ee227d24-9c94-bfa3-166a-4ee6b5dfea09@linux.dev/T/#u
Fixes: 8818039f ("kbuild: add ability to make source rpm buildable using koji")
Reported-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>

commit 3d57e1b7 ("kbuild: refactor the prerequisites of the modpost
rule") moved 'vmlinux.o' inside modpost-args, possibly before some of
the other options. However, getopt() in musl libc follows POSIX and
stops looking for options upon reaching the first non-option argument.
As a result, the '-T' option is misinterpreted as a positional argument,
and the build fails:

  make -f ./scripts/Makefile.modpost
     scripts/mod/modpost   -E   -o Module.symvers vmlinux.o -T modules.order
  -T: No such file or directory
  make[1]: *** [scripts/Makefile.modpost:137: Module.symvers] Error 1
  make: *** [Makefile:1960: modpost] Error 2

The fix is to move all options before 'vmlinux.o' in modpost-args.

Fixes: 3d57e1b7 ("kbuild: refactor the prerequisites of the modpost rule")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

The help message line for building the source RPM package was missing.
Added it.
Signed-off-by: Jun ASAKA <JunASAKA@zzy040330.moe>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Previously, *.rpm files were created under $HOME/rpmbuild/, but since
commit 8818039f ("kbuild: add ability to make source rpm buildable
using koji"), srcrpm-pkg creates the source rpm in the kernel tree
because it sets '_srcrpmdir'.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Dennis Gilmore reports that the BuildID is missing in the arm64 vmlinux
since commit 994b7ac1 ("arm64: remove special treatment for the
link order of head.o").

The issue is that the type of .notes section, which contains the BuildID,
changed from NOTES to PROGBITS.

Ard Biesheuvel figured out that whichever object gets linked first gets
to decide the type of a section. The PROGBITS type is the result of the
compiler emitting .note.GNU-stack as PROGBITS rather than NOTE.

While Ard provided a fix for arm64, I want to fix this globally because
the same issue is happening on riscv since commit 2348e6bf ("riscv:
remove special treatment for the link order of head.o"). This problem
will happen in general for other architectures if they start to drop
unneeded entries from scripts/head-object-list.txt.

Discard .note.GNU-stack in include/asm-generic/vmlinux.lds.h.

Link: https://lore.kernel.org/lkml/CAABkxwuQoz1CTbyb57n0ZX65eSYiTonFCU8-LCQc=74D=xE=rA@mail.gmail.com/
Fixes: 994b7ac1 ("arm64: remove special treatment for the link order of head.o")
Fixes: 2348e6bf ("riscv: remove special treatment for the link order of head.o")
Reported-by: Dennis Gilmore <dennis@ausil.us>
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>

In the case where a firmware file is too large (e.g. someone
downloaded a web page ASCII dump from github...), the firmware object
is released but the pointer is not zerod. If no other firmware file
was found then release would be called again leading to a double kfree.

Also, the size check was only being applied to the initial firmware
load not any of the subsequent attempts. So move the check into a
wrapper that is used for all loads.

Fixes: 01624116 ("drm/i915/uc: use different ggtt pin offsets for uc loads")
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: "Thomas Hellström" <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221221193031.687266-4-John.C.Harrison@Intel.com
(cherry picked from commit 4071d98b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

The catch-all evict can fail due to object lock contention, since it
only goes as far as trylocking the object, due to us already holding the
vm->mutex. Doing a full object lock here can deadlock, since the
vm->mutex is always our inner lock. Add another execbuf pass which drops
the vm->mutex and then tries to grab the object will the full lock,
before then retrying the eviction. This should be good enough for now to
fix the immediate regression with userspace seeing -ENOSPC from execbuf
due to contended object locks during GTT eviction.

v2 (Mani)
  - Also revamp the docs for the different passes.

Testcase: igt@gem_ppgtt@shrink-vs-evict-*
Fixes: 7e00897b ("drm/i915: Add object locking to i915_gem_evict_for_node and i915_gem_evict_something, v2.")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/7627
References: https://gitlab.freedesktop.org/drm/intel/-/issues/7570
References: https://bugzilla.mozilla.org/show_bug.cgi?id=1779558Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Mani Milani <mani@chromium.org>
Cc: <stable@vger.kernel.org> # v5.18+
Reviewed-by: Mani Milani <mani@chromium.org>
Tested-by: Mani Milani <mani@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221216113456.414183-1-matthew.auld@intel.com
(cherry picked from commit 801fa7a8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

The attribute __maybe_unused should remain only until the respective
info is not in the pciidlist. The info can't be added together
with its definition because that would cause the driver to automatically
probe for the device, while it's still not ready for that. However once
pciidlist contains it, the attribute can be removed.

Fixes: 78353039 ("drm/i915/mtl: Add MeteorLake PCI IDs")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221214194944.3670344-1-lucas.demarchi@intel.com
(cherry picked from commit 50490ce0)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

In case of Gen12.50 video and compute engines, TLB_INV registers are
masked - to modify one bit, corresponding bit in upper half of the register
must be enabled, otherwise nothing happens.

Fixes: 77fa9efc ("drm/i915/xehp: Create separate reg definitions for new MCR registers")
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221214075439.402485-1-andrzej.hajda@intel.com
(cherry picked from commit 4d5cf7b1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Pull block fixes from Jens Axboe:
 "Mostly just NVMe, but also a single fixup for BFQ for a regression
  that happened during the merge window. In detail:

   - NVMe pull requests via Christoph:
      - Fix doorbell buffer value endianness (Klaus Jensen)
      - Fix Linux vs NVMe page size mismatch (Keith Busch)
      - Fix a potential use memory access beyong the allocation limit
        (Keith Busch)
      - Fix a multipath vs blktrace NULL pointer dereference (Yanjun
        Zhang)
      - Fix various problems in handling the Command Supported and
        Effects log (Christoph Hellwig)
      - Don't allow unprivileged passthrough of commands that don't
        transfer data but modify logical block content (Christoph
        Hellwig)
      - Add a features and quirks policy document (Christoph Hellwig)
      - Fix some really nasty code that was correct but made smatch
        complain (Sagi Grimberg)

   - Use-after-free regression in BFQ from this merge window (Yu)"

* tag 'block-6.2-2022-12-29' of git://git.kernel.dk/linux:
  nvme-auth: fix smatch warning complaints
  nvme: consult the CSE log page for unprivileged passthrough
  nvme: also return I/O command effects from nvme_command_effects
  nvmet: don't defer passthrough commands with trivial effects to the workqueue
  nvmet: set the LBCC bit for commands that modify data
  nvmet: use NVME_CMD_EFFECTS_CSUPP instead of open coding it
  nvme: fix the NVME_CMD_EFFECTS_CSE_MASK definition
  docs, nvme: add a feature and quirk policy document
  nvme-pci: update sqsize when adjusting the queue depth
  nvme: fix setting the queue depth in nvme_alloc_io_tag_set
  block, bfq: fix uaf for bfqq in bfq_exit_icq_bfqq
  nvme: fix multipath crash caused by flush request when blktrace is enabled
  nvme-pci: fix page size checks
  nvme-pci: fix mempool alloc size
  nvme-pci: fix doorbell buffer value endianness