In BPF_AND and BPF_OR alu cases we have this pattern when the src and dst
tnum is a constant.

 1 dst_reg->var_off = tnum_[op](dst_reg->var_off, src_reg.var_off)
 2 scalar32_min_max_[op]
 3       if (known) return
 4 scalar_min_max_[op]
 5       if (known)
 6          __mark_reg_known(dst_reg,
                   dst_reg->var_off.value [op] src_reg.var_off.value)

The result is in 1 we calculate the var_off value and store it in the
dst_reg. Then in 6 we duplicate this logic doing the op again on the
value.

The duplication comes from the the tnum_[op] handlers because they have
already done the value calcuation. For example this is tnum_and().

 struct tnum tnum_and(struct tnum a, struct tnum b)
 {
	u64 alpha, beta, v;

	alpha = a.value | a.mask;
	beta = b.value | b.mask;
	v = a.value & b.value;
	return TNUM(v, alpha & beta & ~v);
 }

So lets remove the redundant op calculation. Its confusing for readers
and unnecessary. Its also not harmful because those ops have the
property, r1 & r1 = r1 and r1 | r1 = r1.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Martin KaFai Lau says:

====================
This set allows networking prog type to directly read fields from
the in-kernel socket type, e.g. "struct tcp_sock".

Patch 2 has the details on the use case.

v3:
- Pass arg_btf_id instead of fn into check_reg_type() in Patch 1 (Lorenz)
- Move arg_btf_id from func_proto to struct bpf_reg_types in Patch 2 (Lorenz)
- Remove test_sock_fields from .gitignore in Patch 8 (Andrii)
- Add tests to have better coverage on the modified helpers (Alexei)
  Patch 13 is added.
- Use "void *sk" as the helper argument in UAPI bpf.h

v3:
- ARG_PTR_TO_SOCK_COMMON_OR_NULL was attempted in v2.  The _OR_NULL was
  needed because the PTR_TO_BTF_ID could be NULL but note that a could be NULL
  PTR_TO_BTF_ID is not a scalar NULL to the verifier.  "_OR_NULL" implicitly
  gives an expectation that the helper can take a scalar NULL which does
  not make sense in most (except one) helpers.  Passing scalar NULL
  should be rejected at the verification time.

  Thus, this patch uses ARG_PTR_TO_BTF_ID_SOCK_COMMON to specify that the
  helper can take both the btf-id ptr or the legacy PTR_TO_SOCK_COMMON but
  not scalar NULL.  It requires the func_proto to explicitly specify the
  arg_btf_id such that there is a very clear expectation that the helper
  can handle a NULL PTR_TO_BTF_ID.

v2:
- Add ARG_PTR_TO_SOCK_COMMON_OR_NULL (Lorenz)
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

This patch attaches a classifier prog to the ingress filter.
It exercises the following helpers with different socket pointer
types in different logical branches:
1. bpf_sk_release()
2. bpf_sk_assign()
3. bpf_skc_to_tcp_request_sock(), bpf_skc_to_tcp_sock()
4. bpf_tcp_gen_syncookie, bpf_tcp_check_syncookie
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200925000458.3859627-1-kafai@fb.com

The enum tcp_ca_state is available in <linux/tcp.h>.
Remove it from the bpf_tcp_helpers.h to avoid conflict when the bpf prog
needs to include both both <linux/tcp.h> and bpf_tcp_helpers.h.

Modify the bpf_cubic.c and bpf_dctcp.c to use <linux/tcp.h> instead.
The <linux/stddef.h> is needed by <linux/tcp.h>.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200925000452.3859313-1-kafai@fb.com

This test uses bpf_skc_to_tcp_sock() to get a kernel tcp_sock ptr "ktp".
Access the ktp->lsndtime and also pass ktp to bpf_sk_storage_get().

It also exercises the bpf_sk_cgroup_id() and bpf_sk_ancestor_cgroup_id()
with the "ktp".  To do that, a parent cgroup and a child cgroup are
created.  The bpf prog is attached to the child cgroup.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200925000446.3858975-1-kafai@fb.com

This patch uses start_server() and connect_to_fd() from network_helpers.h
to remove the network testing boiler plate codes.  epoll is no longer
needed also since the timeout has already been taken care of also.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200925000440.3858639-1-kafai@fb.com

skel is used.

Global variables are used to store the result from bpf prog.
addr_map, sock_result_map, and tcp_sock_result_map are gone.
Instead, global variables listen_tp, srv_sa6, cli_tp,, srv_tp,
listen_sk, srv_sk, and cli_sk are added.
Because of that, bpf_addr_array_idx and bpf_result_array_idx are also
no longer needed.

CHECK() macro from test_progs.h is reused and bail as soon as
a CHECK failure.

shutdown() is used to ensure the previous data-ack is received.
The bytes_acked, bytes_received, and the pkt_out_cnt checks are
using "<" to accommodate the final ack may not have been received/sent.
It is enough since it is not the focus of this test.

The sk local storage is all initialized to 0xeB9F now, so the
check_sk_pkt_out_cnt() always checks with the 0xeB9F base.  It is to
keep things simple.

The next patch will reuse helpers from network_helpers.h to simplify
things further.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200925000434.3858204-1-kafai@fb.com

This is a mechanical change to
1. move test_sock_fields.c to prog_tests/sock_fields.c
2. rename progs/test_sock_fields_kern.c to progs/test_sock_fields.c

Minimal change is made to the code itself.  Next patch will make
changes to use new ways of writing test, e.g. use skel and global
variables.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200925000427.3857814-1-kafai@fb.com

The patch tests for:
1. bpf_sk_release() can be called on a tcp_sock btf_id ptr.

2. Ensure the tcp_sock btf_id pointer cannot be used
   after bpf_sk_release().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Link: https://lore.kernel.org/bpf/20200925000421.3857616-1-kafai@fb.com

This patch changes the bpf_sk_assign() to take
ARG_PTR_TO_BTF_ID_SOCK_COMMON such that they will work with the pointer
returned by the bpf_skc_to_*() helpers also.

The bpf_sk_lookup_assign() is taking ARG_PTR_TO_SOCKET_"OR_NULL".  Meaning
it specifically takes a literal NULL.  ARG_PTR_TO_BTF_ID_SOCK_COMMON
does not allow a literal NULL, so another ARG type is required
for this purpose and another follow-up patch can be used if
there is such need.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200925000415.3857374-1-kafai@fb.com

This patch changes the bpf_tcp_*_syncookie() to take
ARG_PTR_TO_BTF_ID_SOCK_COMMON such that they will work with the pointer
returned by the bpf_skc_to_*() helpers also.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Link: https://lore.kernel.org/bpf/20200925000409.3856725-1-kafai@fb.com

This patch changes the bpf_sk_storage_*() to take
ARG_PTR_TO_BTF_ID_SOCK_COMMON such that they will work with the pointer
returned by the bpf_skc_to_*() helpers also.

A micro benchmark has been done on a "cgroup_skb/egress" bpf program
which does a bpf_sk_storage_get().  It was driven by netperf doing
a 4096 connected UDP_STREAM test with 64bytes packet.
The stats from "kernel.bpf_stats_enabled" shows no meaningful difference.

The sk_storage_get_btf_proto, sk_storage_delete_btf_proto,
btf_sk_storage_get_proto, and btf_sk_storage_delete_proto are
no longer needed, so they are removed.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Link: https://lore.kernel.org/bpf/20200925000402.3856307-1-kafai@fb.com

The previous patch allows the networking bpf prog to use the
bpf_skc_to_*() helpers to get a PTR_TO_BTF_ID socket pointer,
e.g. "struct tcp_sock *".  It allows the bpf prog to read all the
fields of the tcp_sock.

This patch changes the bpf_sk_release() and bpf_sk_*cgroup_id()
to take ARG_PTR_TO_BTF_ID_SOCK_COMMON such that they will
work with the pointer returned by the bpf_skc_to_*() helpers
also.  For example, the following will work:

	sk = bpf_skc_lookup_tcp(skb, tuple, tuplen, BPF_F_CURRENT_NETNS, 0);
	if (!sk)
		return;
	tp = bpf_skc_to_tcp_sock(sk);
	if (!tp) {
		bpf_sk_release(sk);
		return;
	}
	lsndtime = tp->lsndtime;
	/* Pass tp to bpf_sk_release() will also work */
	bpf_sk_release(tp);

Since PTR_TO_BTF_ID could be NULL, the helper taking
ARG_PTR_TO_BTF_ID_SOCK_COMMON has to check for NULL at runtime.

A btf_id of "struct sock" may not always mean a fullsock.  Regardless
the helper's running context may get a non-fullsock or not,
considering fullsock check/handling is pretty cheap, it is better to
keep the same verifier expectation on helper that takes ARG_PTR_TO_BTF_ID*
will be able to handle the minisock situation.  In the bpf_sk_*cgroup_id()
case,  it will try to get a fullsock by using sk_to_full_sk() as its
skb variant bpf_sk"b"_*cgroup_id() has already been doing.

bpf_sk_release can already handle minisock, so nothing special has to
be done.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200925000356.3856047-1-kafai@fb.com

There is a constant need to add more fields into the bpf_tcp_sock
for the bpf programs running at tc, sock_ops...etc.

A current workaround could be to use bpf_probe_read_kernel().  However,
other than making another helper call for reading each field and missing
CO-RE, it is also not as intuitive to use as directly reading
"tp->lsndtime" for example.  While already having perfmon cap to do
bpf_probe_read_kernel(), it will be much easier if the bpf prog can
directly read from the tcp_sock.

This patch tries to do that by using the existing casting-helpers
bpf_skc_to_*() whose func_proto returns a btf_id.  For example, the
func_proto of bpf_skc_to_tcp_sock returns the btf_id of the
kernel "struct tcp_sock".

These helpers are also added to is_ptr_cast_function().
It ensures the returning reg (BPF_REF_0) will also carries the ref_obj_id.
That will keep the ref-tracking works properly.

The bpf_skc_to_* helpers are made available to most of the bpf prog
types in filter.c. The bpf_skc_to_* helpers will be limited by
perfmon cap.

This patch adds a ARG_PTR_TO_BTF_ID_SOCK_COMMON.  The helper accepting
this arg can accept a btf-id-ptr (PTR_TO_BTF_ID + &btf_sock_ids[BTF_SOCK_TYPE_SOCK_COMMON])
or a legacy-ctx-convert-skc-ptr (PTR_TO_SOCK_COMMON).  The bpf_skc_to_*()
helpers are changed to take ARG_PTR_TO_BTF_ID_SOCK_COMMON such that
they will accept pointer obtained from skb->sk.

Instead of specifying both arg_type and arg_btf_id in the same func_proto
which is how the current ARG_PTR_TO_BTF_ID does, the arg_btf_id of
the new ARG_PTR_TO_BTF_ID_SOCK_COMMON is specified in the
compatible_reg_types[] in verifier.c.  The reason is the arg_btf_id is
always the same.  Discussion in this thread:
https://lore.kernel.org/bpf/20200922070422.1917351-1-kafai@fb.com/

The ARG_PTR_TO_BTF_ID_ part gives a clear expectation that the helper is
expecting a PTR_TO_BTF_ID which could be NULL.  This is the same
behavior as the existing helper taking ARG_PTR_TO_BTF_ID.

The _SOCK_COMMON part means the helper is also expecting the legacy
SOCK_COMMON pointer.

By excluding the _OR_NULL part, the bpf prog cannot call helper
with a literal NULL which doesn't make sense in most cases.
e.g. bpf_skc_to_tcp_sock(NULL) will be rejected.  All PTR_TO_*_OR_NULL
reg has to do a NULL check first before passing into the helper or else
the bpf prog will be rejected.  This behavior is nothing new and
consistent with the current expectation during bpf-prog-load.

[ ARG_PTR_TO_BTF_ID_SOCK_COMMON will be used to replace
  ARG_PTR_TO_SOCK* of other existing helpers later such that
  those existing helpers can take the PTR_TO_BTF_ID returned by
  the bpf_skc_to_*() helpers.

  The only special case is bpf_sk_lookup_assign() which can accept a
  literal NULL ptr.  It has to be handled specially in another follow
  up patch if there is a need (e.g. by renaming ARG_PTR_TO_SOCKET_OR_NULL
  to ARG_PTR_TO_BTF_ID_SOCK_COMMON_OR_NULL). ]

[ When converting the older helpers that take ARG_PTR_TO_SOCK* in
  the later patch, if the kernel does not support BTF,
  ARG_PTR_TO_BTF_ID_SOCK_COMMON will behave like ARG_PTR_TO_SOCK_COMMON
  because no reg->type could have PTR_TO_BTF_ID in this case.

  It is not a concern for the newer-btf-only helper like the bpf_skc_to_*()
  here though because these helpers must require BTF vmlinux to begin
  with. ]
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200925000350.3855720-1-kafai@fb.com

check_reg_type() checks whether a reg can be used as an arg of a
func_proto.  For PTR_TO_BTF_ID, the check is actually not
completely done until the reg->btf_id is pointing to a
kernel struct that is acceptable by the func_proto.

Thus, this patch moves the btf_id check into check_reg_type().
"arg_type" and "arg_btf_id" are passed to check_reg_type() instead of
"compatible".  The compatible_reg_types[] usage is localized in
check_reg_type() now.

The "if (!btf_id) verbose(...); " is also removed since it won't happen.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200925000344.3854828-1-kafai@fb.com

Merge branch 'rtt-speedup.2020.09.16a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu into bpf-next
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

This reverts commit 31f23a6a.

This change made many selftests/bpf flaky: flow_dissector, sk_lookup, sk_assign and others.
There was no issue in the code.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Florian Fainelli says:

====================
net: dsa: bcm_sf2: Additional DT changes

This patch series includes some additional changes to the bcm_sf2 in
order to support the Device Tree firmwares provided on such platforms.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to include MDIO address 0, which is how our Device Tree blobs
indicate where to find the external BCM53125 switches.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While the switch driver is written such that port 5 or 8 could be CPU
ports, the use case on Broadcom STB chips is to use port 8 exclusively.
The platform firmware does make port 5 comply to a proper DSA CPU port
binding by specifiying an "ethernet" phandle. This is undesirable for
now until we have an user-space configuration mechanism (such as
devlink) which could support dynamically changing the port flavor at
run time.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

George Cherian says:

====================
octeontx2: Add support for VLAN based flow distribution

This series add support for VLAN based flow distribution for octeontx2
netdev driver. This adds support for configuring the same via ethtool.

Following tests have been done.
	- Multi VLAN flow with same SD
	- Multi VLAN flow with same SDFN
	- Single VLAN flow with multi SD
	- Single VLAN flow with multi SDFN
All tests done for udp/tcp both v4 and v6
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to control rx-flow-hash based on VLAN.
By default VLAN plus 4-tuple based hashing is enabled.
Changes can be done runtime using ethtool

To enable 2-tuple plus VLAN based flow distribution
  # ethtool -N <intf> rx-flow-hash <prot> sdv
To enable 4-tuple plus VLAN based flow distribution
  # ethtool -N <intf> rx-flow-hash <prot> sdfnv
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added support for PF/VF drivers to choose RSS flow key algorithm
with VLAN tag included in hashing input data. Only CTAG is considered.
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

kernel-doc expects the function prototype to be just after
the kernel-doc markup, as otherwise it will get it all wrong:

	./net/core/dev.c:10036: warning: Excess function parameter 'dev' description in 'WAIT_REFS_MIN_MSECS'

Fixes: 0e4be9e5 ("net: use exponential backoff in netdev_wait_allrefs")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Robert Marko says:

====================
net: mdio-ipq4019: add Clause 45 support

This patch series adds support for Clause 45 to the driver.

While at it also change some defines to upper case to match rest of the driver.

Changes since v4:
* Rebase onto net-next.git

Changes since v1:
* Drop clock patches, these need further investigation and
no user for non default configuration has been found
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

While up-streaming the IPQ4019 driver it was thought that the controller had no Clause 45 support,
but it actually does and its activated by writing a bit to the mode register.

So lets add it as newer SoC-s use the same controller and Clause 45 compliant PHY-s.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the commit adding the IPQ4019 MDIO driver, defines for timeout and sleep partially used lower case.
Lets change it to upper case in line with the rest of driver defines.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Subbaraya Sundeep says:

====================
Introduce mbox tracepoints for Octeontx2

This patchset adds tracepoints support for mailbox.
In Octeontx2, PFs and VFs need to communicate with AF
for allocating and freeing resources. Once all the
configuration is done by AF for a PF/VF then packet I/O
can happen on PF/VF queues. When an interface
is brought up many mailbox messages are sent
to AF for initializing queues. Say a VF is brought up
then each message is sent to PF and PF forwards to
AF and response also traverses from AF to PF and then VF.
To aid debugging, tracepoints are added at places where
messages are allocated, sent and message interrupts.
Below is the trace of one of the messages from VF to AF
and AF response back to VF:

~ # echo 1 > /sys/kernel/tracing/events/rvu/enable
~ # ifconfig eth20 up
[  279.379559] eth20 NIC Link is UP 10000 Mbps Full duplex
~ # cat /sys/kernel/tracing/trace
        ifconfig-171   [000] ....   275.753345: otx2_msg_alloc: [0002:02:00.1] msg:(0x400) size:40

        ifconfig-171   [000] ...1   275.753347: otx2_msg_send: [0002:02:00.1] sent 1 msg(s) of size:48

          <idle>-0     [001] dNh1   275.753356: otx2_msg_interrupt: [0002:02:00.0] mbox interrupt VF(s) to PF (0x1)

    kworker/u9:1-90    [001] ...1   275.753364: otx2_msg_send: [0002:02:00.0] sent 1 msg(s) of size:48

    kworker/u9:1-90    [001] d.h.   275.753367: otx2_msg_interrupt: [0002:01:00.0] mbox interrupt PF(s) to AF (0x2)

    kworker/u9:2-167   [002] ....   275.753535: otx2_msg_process: [0002:01:00.0] msg:(0x400) error:0

    kworker/u9:2-167   [002] ...1   275.753537: otx2_msg_send: [0002:01:00.0] sent 1 msg(s) of size:32

          <idle>-0     [003] d.h1   275.753543: otx2_msg_interrupt: [0002:02:00.0] mbox interrupt AF to PF (0x1)

          <idle>-0     [001] d.h2   275.754376: otx2_msg_interrupt: [0002:02:00.1] mbox interrupt PF to VF (0x1)

v3 changes:
 Removed EXPORT_TRACEPOINT_SYMBOLS of otx2_msg_send and otx2_msg_check
 since they are called locally only

v2 changes:
 Removed otx2_msg_err tracepoint since it is similar to devlink_hwerr
 and it will be used instead when devlink supported is added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With tracepoints support present in the mailbox
code this patch adds tracepoints in PF and VF drivers
at places where mailbox messages are allocated,
sent and at message interrupts.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added tracepoints in mailbox code so that
the mailbox operations like message allocation,
sending message and message interrupts are traced.
Also the mailbox errors occurred like timeout
or wrong responses are traced.
These will help in debugging mailbox issues.

Here's an example output showing one of the mailbox
messages sent by PF to AF and AF responding to it:

~# mount -t tracefs none /sys/kernel/tracing/
~# echo 1 > /sys/kernel/tracing/events/rvu/enable
~# ifconfig eth0 up
~# cat /sys/kernel/tracing/trace

~# cat /sys/kernel/tracing/trace
 tracer: nop

		      _-----=> irqs-off
		     / _----=> need-resched
		    | / _---=> hardirq/softirq
		    || / _--=> preempt-depth
		    ||| /     delay
   TASK-PID   CPU#  ||||    TIMESTAMP  FUNCTION
      | |       |   ||||       |         |
ifconfig-2382  [002] ....   756.161892: otx2_msg_alloc: [0002:02:00.0] msg:(0x400) size:40

ifconfig-2382  [002] ...1   756.161895: otx2_msg_send: [0002:02:00.0] sent 1 msg(s) of size:48

 <idle>-0     [000] d.h1   756.161902: otx2_msg_interrupt: [0002:01:00.0] mbox interrupt PF(s) to AF (0x2)

kworker/u49:0-1165  [000] ....   756.162049: otx2_msg_process: [0002:01:00.0] msg:(0x400) error:0

kworker/u49:0-1165  [000] ...1   756.162051: otx2_msg_send: [0002:01:00.0] sent 1 msg(s) of size:32

kworker/u49:0-1165  [000] d.h.   756.162056: otx2_msg_interrupt: [0002:02:00.0] mbox interrupt AF to PF (0x1)
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The comment "holders of db->lock must always block IRQs" and related
code to do irqsave and irqrestore don't make sense since we are in a
IRQ-disabled hardIRQ context.

Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

A number of static variables were not modified. Make them const to allow
the compiler to put them in read-only memory. In order to do so,
constify a couple of input pointers as well as some local pointers.
This moves about 35Kb to read-only memory as seen by the output of the
size command.

Before:
   text    data     bss     dec     hex filename
 404938  111534     640  517112   7e3f8 drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge.ko

After:
   text    data     bss     dec     hex filename
 439499   76974     640  517113   7e3f9 drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge.ko
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
net: bridge: mcast: IGMPv3/MLDv2 fast-path (part 2)

This is the second part of the IGMPv3/MLDv2 support which adds support
for the fast-path. In order to be able to handle source entries we add
mdb support for S,G entries (i.e. we add source address support to
br_ip), that requires to extend the current mdb netlink API, fortunately
we just add another attribute which will contain nested future mdb
attributes, then we use it to add support for S,G user- add, del and
dump. The lookup sequence is simple: when IGMPv3/MLDv2 are enabled do
the S,G lookup first and if it fails fallback to *,G. The more complex
part is when we begin handling source lists and auto-installing S,G entries
and *,G filter mode transitions. We have the following cases:
 1) *,G INCLUDE -> EXCLUDE transition: we need to install the port in
    all of *,G's installed S,G entries for proper replication (except
    the ones explicitly blocked), this is also necessary when adding a
    new *,G EXCLUDE port group

 2) *,G EXCLUDE -> INCLUDE transition: we need to remove the port from
    all of *,G's installed S,G entries, this is also necessary when
    removing a *,G port group

 3) New S,G port entry: we need to install all current *,G EXCLUDE ports

 4) Remove S,G port entry: if all other port groups were auto-installed we
    can safely remove them and delete the whole S,G entry

Currently we compute these operations from the available ports, their
source lists and their filter mode. In the future we can extend the port
group structure and reduce the running time of these ops. Also one
current limitation is that host-joined S,G entries are not supported.
I.e. one cannot add "dev bridge port bridge" mdb S,G entries. The host
join is currently considered an EXCLUDE {} join, so it's reflected in
all of *,G's installed S,G entries. If an S,G,port entry is added as
temporary then the kernel can take it over if a source shows up from a
report, permanent entries are skipped. In order to properly handle
blocked sources we add a new port group blocked flag to avoid forwarding
to that port group in the S,G. Finally when forwarding we use the port
group filter mode (if it's INCLUDE and the port group is from a *,G then
don't replicate to it, respectively if it's EXCLUDE then forward) and the
blocked flag (obviously if it's set - skip that port unless it's a
router port) to decide if the port should be skipped. Another limitation
is that we can't do some of the above transitions without small traffic
drop while installing/removing entries. That will be taken care of when
we add atomic swap of port replication lists later.

Patch break down:
 patches 1-3: prepare the mdb code for better extack support which is
              used in future patches to return a more meaningful error
 patches 4-6: add the source address field to struct br_ip, and do minor
              cleanups around it
 patches 7-8: extend the mdb netlink API so we can send new mdb
              attributes and uses the new API for S,G entry add/del/dump
              support
 patch     9: takes care of S,G entries when doing a lookup (first S,G
              then *,G lookup)
 patch    10: adds a new port group field and attribute for origin protocol
              we use the already available RTPROT_ definitions,
              currently user-space entries are added as RTPROT_STATIC and
              kernel entries are added as RTPROT_KERNEL, we may allow
              user-space to set custom values later (e.g. for FRR, clag)
 patch    11: adds an internal S,G,port rhashtable to speed up filter
              mode transitions
 patch    12: initial automatic install of S,G entries based on port
              groups' source lists
 patch    13: handles port group modes on transitions or when new
              port group entries are added
 patch    14: self-explanatory - adds support for blocked port group
              entries needed to stop forwarding to particular S,G,port
              entries
 patch    15: handles host-join/leave state changes, treats host-joins
              as EXCLUDE {} groups (reflected in all *,G's S,G entries)
 patch    16: finally adds the fast-path filter mode and block flag
              support

Here're the sets that will come next (in order):
 - iproute2 support for IGMPv3/MLDv2
 - selftests for all mode transitions and group flags
 - explicit host tracking for proper fast-leave support
 - atomic port replication lists (these are also needed for broadcast
   forwarding optimizations)
 - mode transition optimization and removal of open-coded sorted lists

Not implemented yet:
 - Host IGMPv3/MLDv2 filter support (currently we handle only join/leave
   as before)
 - Proper other querier source timer and value updates
 - IGMPv3/v2 MLDv2/v1 compat (I have a few rough patches for this one)

v2: fix build with CONFIG_BATMAN_ADV_MCAST in patch 6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to avoid forwarding to ports in MCAST_INCLUDE filter mode when the
mdst entry is a *,G or when the port has the blocked flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since host joins are considered as EXCLUDE {} joins we need to reflect
that in all of *,G ports' S,G entries. Since the S,Gs can have
host_joined == true only set automatically we can safely set it to false
when removing all automatically added entries upon S,G delete.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When excluding S,G entries we need a way to block a particular S,G,port.
The new port group flag is managed based on the source's timer as per
RFCs 3376 and 3810. When a source expires and its port group is in
EXCLUDE mode, it will be blocked.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to handle group filter mode transitions and initial state.
To change a port group's INCLUDE -> EXCLUDE mode (or when we have added
a new port group in EXCLUDE mode) we need to add that port to all of
*,G ports' S,G entries for proper replication. When the EXCLUDE state is
changed from IGMPv3 report, br_multicast_fwd_filter_exclude() must be
called after the source list processing because the assumption is that
all of the group's S,G entries will be created before transitioning to
EXCLUDE mode, i.e. most importantly its blocked entries will already be
added so it will not get automatically added to them.
The transition EXCLUDE -> INCLUDE happens only when a port group timer
expires, it requires us to remove that port from all of *,G ports' S,G
entries where it was automatically added previously.
Finally when we are adding a new S,G entry we must add all of *,G's
EXCLUDE ports to it.
In order to distinguish automatically added *,G EXCLUDE ports we have a
new port group flag - MDB_PG_FLAGS_STAR_EXCL.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for automatic install of S,G mdb entries based
on the port group's source list and the source entry's timer.
Once installed the S,G will be used when forwarding packets if the
approprate multicast/mld versions are set. A new source flag called
BR_SGRP_F_INSTALLED denotes if the source has a forwarding mdb entry
installed.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To speedup S,G forward handling we need to be able to quickly find out
if a port is a member of an S,G group. To do that add a global S,G port
rhashtable with key: source addr, group addr, protocol, vid (all br_ip
fields) and port pointer.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to be able to differentiate between pg entries created by
user-space and the kernel when we start generating S,G entries for
IGMPv3/MLDv2's fast path. User-space entries are created by default as
RTPROT_STATIC and the kernel entries are RTPROT_KERNEL. Later we can
allow user-space to provide the entry rt_protocol so we can
differentiate between who added the entries specifically (e.g. clag,
admin, frr etc).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>