- 26 Feb, 2020 36 commits
-
-
Laurent Pinchart authored
The omapdss_hdmi_ops .set_hdmi_mode() and .set_infoframe() operations operations are not used anymore, remove them. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Tested-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by:
-
Laurent Pinchart authored
The HDMI4 encoder is transitioning to the drm_bridge API, implement the last missing operation. Signed-off-by:
-
Laurent Pinchart authored
Move the omap_dss_device .set_timings(), .enable() and .disable() operations to the drm_bridge functions. As the drm_bridge for the HDMI encoder is unconditionally registered and attached, those operations will be called at the appropriate time. The omapdss device .set_infoframe() and .set_hdmi_mode() operations have no equivalent in drm_bridge. Thir content is thus moved to the bridge .enable() operation as the data they store is not needed before the HDMI encoder gets enabled. Signed-off-by:
-
Laurent Pinchart authored
Move the omap_dss_device .set_timings(), .enable() and .disable() operations to the drm_bridge functions. As the drm_bridge for the HDMI encoder is unconditionally registered and attached, those operations will be called at the appropriate time. The omapdss device .set_infoframe() and .set_hdmi_mode() operations have no equivalent in drm_bridge. Thir content is thus moved to the bridge .enable() operation as the data they store is not needed before the HDMI encoder gets enabled. Signed-off-by:
-
Laurent Pinchart authored
In order to integrate with a chain of drm_bridge, the internal HDMI5 encoder has to expose the EDID read operation through the drm_bridge API. Register a bridge at initialisation time to do so. For the time being make the next bridge in the chain optional as the HDMI output is still based on omap_dss_device. The create_connector argument to the bridge attach function is also ignored for the same reason. This will be changed later when removing the related omapdrm-specific display drivers. Signed-off-by:
-
Laurent Pinchart authored
In order to integrate with a chain of drm_bridge, the internal HDMI4 encoder has to expose the EDID read operation through the drm_bridge API. Register a bridge at initialisation time to do so. For the time being make the next bridge in the chain optional as the HDMI output is still based on omap_dss_device. The create_connector argument to the bridge attach function is also ignored for the same reason. This will be changed later when removing the related omapdrm-specific display drivers. Signed-off-by:
-
Laurent Pinchart authored
In preparation of adding DRM bridge support to the hdmi5 encoder code, rework the EDID read to isolate data read. The hdmi_read_edid() function is the main entry point. It performs all initialisation steps required prior to reading the EDID (such as ensuring the device is powered on), as well as corresponding cleanup steps afterwards. EDID read itself is handled by hdmi_read_edid_data() that calls the hdmi5_core_ddc_read() function to read individual blocks. This new code architecture will allow reusing hdmi_read_edid() and hdmi5_core_ddc_read() for the drm_bridge EDID read implementation, while swapping out hdmi_read_edid_data() for the DRM drm_do_get_edid() function. Signed-off-by:
-
Laurent Pinchart authored
In preparation of adding DRM bridge support to the hdmi4 encoder code, rework the EDID read to isolate data read. The hdmi_read_edid() function is the main entry point. It performs all initialisation steps required prior to reading the EDID (such as ensuring the device is powered on), as well as corresponding cleanup steps afterwards. EDID read itself is handled by hdmi_read_edid_data() that calls the hdmi4_core_ddc_read() function to read individual blocks. This new code architecture will allow reusing hdmi_read_edid() and hdmi4_core_ddc_read() for the drm_bridge EDID read implementation, while swapping out hdmi_read_edid_data() for the DRM drm_do_get_edid() function. Signed-off-by:
-
Laurent Pinchart authored
Bring the omapdss-specific .read_edid() operation in sync with the drm_bridge .get_edid() operation to ease code reuse. Signed-off-by:
-
Laurent Pinchart authored
As part of the move to drm_bridge ops, the dssdev ops will become empty for some of the internal encoders. Make them optional in the driver to allow them to be removed completely, easing the transition. Signed-off-by:
-
Laurent Pinchart authored
In order to support drm_bridge-based pipeline, the internal HDMI encoders will need to expose the EDID read operation through the drm_bridge API, and thus to expose a drm_bridge instance corresponding to the encoder. The HDMI encoders are however handled as omap_dss_device instances, which conflicts with this requirement. In order to move forward with the drm_bridge transition, add support for creating drm_bridge instances local to DSS outputs. If a local bridge is passed to the omapdss_device_init_output() function, it is used as the first bridge in the chain, and the omap_dss_device.next_bridge field is set to the next bridge for the use of the internal encoders' bridges. Signed-off-by:
-
Laurent Pinchart authored
The DSS core looks up the next device connected to an output by traversing the OF graph. It currently hardcodes the local port number to 0, which breaks any output with a different port number (SDI on OMAP3 and any DPI output but the first one). Fix this by repurposing the currently unused of_ports bitmask in omap_dss_device with an of_port output port number, and use it to traverse the OF graph. Signed-off-by:
-
Laurent Pinchart authored
Replace the manual panel handling code by a drm_panel_bridge. This simplifies the driver and allows all components in the display pipeline to be treated as bridges, paving the way to generic connector handling. Signed-off-by:
-
Laurent Pinchart authored
Move the code that computes the DRM connector type for the omapdss_device display type to a new omapdss_device_connector_type() function for later reuse. Signed-off-by:
Sam Ravnborg <sam@ravnborg.org> Tested-by:
-
Laurent Pinchart authored
Remove the omap_connector_get_hdmi_mode() function as the HDMI mode can be accessed directly from the connector's display info. Signed-off-by:
-
Laurent Pinchart authored
When the DSS initialises its output DPI and SDI ports, failures don't clean up previous successfully initialised ports. This can lead to resource leak or memory corruption. Fix it. Reported-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Laurent Pinchart authored
Most bridge drivers create a DRM connector to model the connector at the output of the bridge. This model is historical and has worked pretty well so far, but causes several issues: - It prevents supporting more complex display pipelines where DRM connector operations are split over multiple components. For instance a pipeline with a bridge connected to the DDC signals to read EDID data, and another one connected to the HPD signal to detect connection and disconnection, will not be possible to support through this model. - It requires every bridge driver to implement similar connector handling code, resulting in code duplication. - It assumes that a bridge will either be wired to a connector or to another bridge, but doesn't support bridges that can be used in both positions very well (although there is some ad-hoc support for this in the analogix_dp bridge driver). In order to solve these issues, ownership of the connector needs to be moved to the display controller driver. To avoid code duplication in display controller drivers, add a new helper to create and manage a DRM connector backed by a chain of bridges. All connector operations are delegating to the appropriate bridge in the chain. Signed-off-by:
Boris Brezillon <boris.brezillon@collabora.com> Acked-by:
-
Laurent Pinchart authored
The tfp410 driver can operate as part of a pipeline where the drm_connector is created by the display controller. Enable this mode of operation by skipping creation of a drm_connector internally. Signed-off-by:
-
Laurent Pinchart authored
Now that a driver is available for display connectors, replace the manual connector handling code with usage of the DRM bridge API. The tfp410 driver doesn't deal with the display connector directly anymore, but still delegates drm_connector operations to the next bridge. This brings us one step closer to having the tfp410 driver handling the TFP410 only. Signed-off-by:
-
Laurent Pinchart authored
Implement the newly added bridge connector operations, allowing the usage of drm_bridge_panel with drm_bridge_connector. Signed-off-by:
-
Laurent Pinchart authored
The TI TPD12S015 is an HDMI level shifter and ESD protector controlled through GPIOs. Add a DRM bridge driver for the device. Signed-off-by:
-
Laurent Pinchart authored
Display connectors are modelled in DT as a device node, but have so far been handled manually in several bridge drivers. This resulted in duplicate code in several bridge drivers, with slightly different (and thus confusing) logics. In order to fix this, implement a bridge driver for display connectors. The driver centralises logic for the DVI, HDMI, VGAn composite and S-video connectors and exposes corresponding bridge operations. This driver in itself doesn't solve the issue completely, changes in bridge and display controller drivers are needed to make use of the new connector driver. Signed-off-by:
Maxime Ripard <mripard@kernel.org> Reviewed-by:
-
Laurent Pinchart authored
The TI OPA362 is an analog video amplifier controlled through a GPIO. Add support for it to the simple-bridge driver. Signed-off-by:
Andrzej Hajda <a.hajda@samsung.com> Reviewed-by:
-
Laurent Pinchart authored
If an enable GPIO is declared in the firmware, assert it when enabling the bridge and deassert it when disabling it. Signed-off-by:
Stefan Agner <stefan@agner.ch> Reviewed-by:
-
Laurent Pinchart authored
Create a new simple_bridge_info structure that stores information about the bridge model, and store the bridge timings in there, along with the connector type. Use that new structure for of_device_id data. This enables support for non-VGA bridges. Signed-off-by:
-
Laurent Pinchart authored
The dumb-vga-dac driver can support simple DRM bridges without being limited to VGA DACs. Rename it to simple-bridge. Signed-off-by:
-
Laurent Pinchart authored
The dumb-vga-dac driver is a simple DRM bridge driver for simple VGA DACs that don't require configuration. Other non-VGA bridges fall in a similar category, and would benefit from a common driver. Prepare for this by renaming the internal symbols from dumb-vga-dac to simple-bridge. Signed-off-by:
-
Laurent Pinchart authored
Most bridge drivers create a DRM connector to model the connector at the output of the bridge. This model is historical and has worked pretty well so far, but causes several issues: - It prevents supporting more complex display pipelines where DRM connector operations are split over multiple components. For instance a pipeline with a bridge connected to the DDC signals to read EDID data, and another one connected to the HPD signal to detect connection and disconnection, will not be possible to support through this model. - It requires every bridge driver to implement similar connector handling code, resulting in code duplication. - It assumes that a bridge will either be wired to a connector or to another bridge, but doesn't support bridges that can be used in both positions very well (although there is some ad-hoc support for this in the analogix_dp bridge driver). In order to solve these issues, ownership of the connector should be moved to the display controller driver (where it can be implemented using helpers provided by the core). Extend the bridge API to allow disabling connector creation in bridge drivers as a first step towards the new model. The new flags argument to the bridge .attach() operation allows instructing the bridge driver to skip creating a connector. Unconditionally set the new flags argument to 0 for now to keep the existing behaviour, and modify all existing bridge drivers to return an error when connector creation is not requested as they don't support this feature yet. The change is based on the following semantic patch, with manual review and edits. @ rule1 @ identifier funcs; identifier fn; @@ struct drm_bridge_funcs funcs = { ..., .attach = fn }; @ depends on rule1 @ identifier rule1.fn; identifier bridge; statement S, S1; @@ int fn( struct drm_bridge *bridge + , enum drm_bridge_attach_flags flags ) { ... when != S + if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) { + DRM_ERROR("Fix bridge driver to make connector optional!"); + return -EINVAL; + } + S1 ... } @ depends on rule1 @ identifier rule1.fn; identifier bridge, flags; expression E1, E2, E3; @@ int fn( struct drm_bridge *bridge, enum drm_bridge_attach_flags flags ) { <... drm_bridge_attach(E1, E2, E3 + , flags ) ...> } @@ expression E1, E2, E3; @@ drm_bridge_attach(E1, E2, E3 + , 0 ) Signed-off-by:Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Laurent Pinchart authored
In preparation for a connector creation helper based on a chain of bridges, add a flag to the drm_bridge structure to report support for interlaced modes. This will be used to set the connector's interlace_allowed flag. Signed-off-by:
-
Laurent Pinchart authored
To support implementation of DRM connectors on top of DRM bridges instead of by bridges, the drm_bridge needs to expose new operations and data: - Output detection, hot-plug notification, mode retrieval and EDID retrieval operations - Bitmask of supported operations - Bridge output type - I2C adapter for DDC access Add and document these. Three new bridge helper functions are also added to handle hot plug notification in a way that is as transparent as possible for the bridges. Signed-off-by:
-
Laurent Pinchart authored
Clean up the drm_bridge overview documentation, and expand the operations documentation to provide more details on API usage. Signed-off-by:
-
Laurent Pinchart authored
The drm_bridge_funcs atomic_state_duplicate and atomic_state_destroy operations are erroneously documented as having a default implementation if not implemented in bridge drivers. This isn't correct, fix the documentation. Signed-off-by:
-
Laurent Pinchart authored
The drm_encoder.bridge_chain is not meant to be touched manually by drivers. Make this clear in the documentation. Signed-off-by:
-
Laurent Pinchart authored
The drm_display_info structure contains many fields related to HDMI sinks, but none that identifies if a sink compliant with CEA-861 (EDID) shall be treated as an HDMI sink or a DVI sink. Add such a flag, and populate it according to section 8.3.3 ("DVI/HDMI Device Discrimination") of the HDMI v1.3 specification. Signed-off-by:Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Laurent Pinchart authored
drm_connector.c contains a map of connector types (DRM_MODE_CONNECTOR_*) to name strings, but doesn't expose it. This leads to drivers having to store a similar map. Add a new drm_get_connector_type_name() helper function that return a name string for a connector type. Signed-off-by:
-
Laurent Pinchart authored
The hdmi_avi_infoframe_init() never needs to return an error, change its return type to void. Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Reviewed-by:
-
- 25 Feb, 2020 4 commits
-
-
Nicolas Boichat authored
When there is a single power domain per device, the core will ensure the power domain is switched on (so it is technically equivalent to having not power domain specified at all). However, when there are multiple domains, as in MT8183 Bifrost GPU, we need to handle them in driver code. Signed-off-by:
Nicolas Boichat <drinkcat@chromium.org> Reviewed-by:
Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by:
Steven Price <steven.price@arm.com> Signed-off-by:
Rob Herring <robh@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200207052627.130118-6-drinkcat@chromium.org
-
Nicolas Boichat authored
Some GPUs, namely, the bifrost/g72 part on MT8183, have a second regulator for their SRAM, let's add support for that. We extend the framework in a generic manner so that we could support more than 2 regulators, if required. Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Nicolas Boichat authored
It is useful to know which component cannot be powered on. Signed-off-by:
Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com> Reviewed-by:
-
Boris Brezillon authored
Propagate bus format/flags so that the previous bridge element in the chain knows which input format the panel bridge expects. v11: * Fix a typo in the subject * Update the commit message so it's readable by itself v10: * Add changelog to the commit message v8 -> v9: * No changes v7: * Set atomic state hooks explicitly v4 -> v6: * Not part of the series v3: * Adjust things to match the new bus-format negotiation approach * Use drm_atomic_helper_bridge_propagate_bus_fmt * Don't implement ->atomic_check() (the core now takes care of bus flags propagation) v2: * Adjust things to match the new bus-format negotiation approach Signed-off-by:
-
