Normally, calling alloc_iova() using an iova_domain with insufficient
pfns remaining between start_pfn and dma_limit will fail and return a
NULL pointer. Unexpectedly, if such a "full" iova_domain contains an
iova with pfn_lo == 0, the alloc_iova() call will instead succeed and
return an iova containing invalid pfns.

This is caused by an underflow bug in __alloc_and_insert_iova_range()
that occurs after walking the "full" iova tree when the search ends
at the iova with pfn_lo == 0 and limit_pfn is then adjusted to be just
below that (-1). This (now huge) limit_pfn gives the impression that a
vast amount of space is available between it and start_pfn and thus
a new iova is allocated with the invalid pfn_hi value, 0xFFF.... .

To rememdy this, a check is introduced to ensure that adjustments to
limit_pfn will not underflow.

This issue has been observed in the wild, and is easily reproduced with
the following sample code.

	struct iova_domain *iovad = kzalloc(sizeof(*iovad), GFP_KERNEL);
	struct iova *rsvd_iova, *good_iova, *bad_iova;
	unsigned long limit_pfn = 3;
	unsigned long start_pfn = 1;
	unsigned long va_size = 2;

	init_iova_domain(iovad, SZ_4K, start_pfn, limit_pfn);
	rsvd_iova = reserve_iova(iovad, 0, 0);
	good_iova = alloc_iova(iovad, va_size, limit_pfn, true);
	bad_iova = alloc_iova(iovad, va_size, limit_pfn, true);

Prior to the patch, this yielded:
	*rsvd_iova == {0, 0}   /* Expected */
	*good_iova == {2, 3}   /* Expected */
	*bad_iova  == {-2, -1} /* Oh no... */

After the patch, bad_iova is NULL as expected since inadequate
space remains between limit_pfn and start_pfn after allocating
good_iova.
Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

With IOVA allocation suitably tidied up, we are finally free to opt in
to the per-CPU caching mechanism. The caching alone can provide a modest
improvement over walking the rbtree for weedier systems (iperf3 shows
~10% more ethernet throughput on an ARM Juno r1 constrained to a single
650MHz Cortex-A53), but the real gain will be in sidestepping the rbtree
lock contention which larger ARM-based systems with lots of parallel I/O
are starting to feel the pain of.
Reviewed-by: Nate Watterson <nwatters@codeaurora.org>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Now that allocation is suitably abstracted, our private alloc/free
helpers can drive the trivial MSI cookie allocator directly as well,
which lets us clean up its exposed guts from iommu_dma_map_msi_msg() and
simplify things quite a bit.
Reviewed-by: Nate Watterson <nwatters@codeaurora.org>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

In preparation for some IOVA allocation improvements, clean up all the
explicit struct iova usage such that all our mapping, unmapping and
cleanup paths deal exclusively with addresses rather than implementation
details. In the process, a few of the things we're touching get renamed
for the sake of internal consistency.
Reviewed-by: Nate Watterson <nwatters@codeaurora.org>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Now that we're applying the IOMMU API reserved regions to our IOVA
domains, we shouldn't need to privately special-case PCI windows, or
indeed anything else which isn't specific to our iommu-dma layer.
However, since those aren't IOMMU-specific either, rather than start
duplicating code into IOMMU drivers let's transform the existing
function into an iommu_get_resv_regions() helper that they can share.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Now that it's simple to discover the necessary reservations for a given
device/IOMMU combination, let's wire up the appropriate handling. Basic
reserved regions and direct-mapped regions we simply have to carve out
of IOVA space (the IOMMU core having already mapped the latter before
attaching the device). For hardware MSI regions, we also pre-populate
the cookie with matching msi_pages. That way, irqchip drivers which
normally assume MSIs to require mapping at the IOMMU can keep working
without having to special-case their iommu_dma_map_msi_msg() hook, or
indeed be aware at all of quirks preventing the IOMMU from translating
certain addresses.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Even if a host controller's CPU-side MMIO windows into PCI I/O space do
happen to leak into PCI memory space such that it might treat them as
peer addresses, trying to reserve the corresponding I/O space addresses
doesn't do anything to help solve that problem. Stop doing a silly thing.

Fixes: fade1ec0 ("iommu/dma: Avoid PCI host bridge windows")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

The introduction of reserved regions has left a couple of rough edges
which we could do with sorting out sooner rather than later. Since we
are not yet addressing the potential dynamic aspect of software-managed
reservations and presenting them at arbitrary fixed addresses, it is
incongruous that we end up displaying hardware vs. software-managed MSI
regions to userspace differently, especially since ARM-based systems may
actually require one or the other, or even potentially both at once,
(which iommu-dma currently has no hope of dealing with at all). Let's
resolve the former user-visible inconsistency ASAP before the ABI has
been baked into a kernel release, in a way that also lays the groundwork
for the latter shortcoming to be addressed by follow-up patches.

For clarity, rename the software-managed type to IOMMU_RESV_SW_MSI, use
IOMMU_RESV_MSI to describe the hardware type, and document everything a
little bit. Since the x86 MSI remapping hardware falls squarely under
this meaning of IOMMU_RESV_MSI, apply that type to their regions as well,
so that we tell the same story to userspace across all platforms.

Secondly, as the various region types require quite different handling,
and it really makes little sense to ever try combining them, convert the
bitfield-esque #defines to a plain enum in the process before anyone
gets the wrong impression.

Fixes: d30ddcaa ("iommu: Add a new type field in iommu_resv_region")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: kvm@vger.kernel.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

For some unknown reasons, in some cases, FLPD cache invalidation doesn't
work properly with SYSMMU v5 controllers found in Exynos5433 SoCs. This
can be observed by a firmware crash during initialization phase of MFC
video decoder available in the mentioned SoCs when IOMMU support is
enabled. To workaround this issue perform a full TLB/FLPD invalidation
in case of replacing any first level page descriptors in case of SYSMMU v5.

Fixes: 740a01ee ("iommu/exynos: Add support for v5 SYSMMU")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Documentation specifies that SYSMMU should be in blocked state while
performing TLB/FLPD cache invalidation, so add needed calls to
sysmmu_block/unblock.

Fixes: 66a7ed84 ("iommu/exynos: Apply workaround of caching fault page table entries")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

The function device_to_iommu() in the Intel VT-d driver
lacks a NULL-ptr check, resulting in this oops at boot on
some platforms:

 BUG: unable to handle kernel NULL pointer dereference at 00000000000007ab
 IP: [<ffffffff8132234a>] device_to_iommu+0x11a/0x1a0
 PGD 0

 [...]

 Call Trace:
   ? find_or_alloc_domain.constprop.29+0x1a/0x300
   ? dw_dma_probe+0x561/0x580 [dw_dmac_core]
   ? __get_valid_domain_for_dev+0x39/0x120
   ? __intel_map_single+0x138/0x180
   ? intel_alloc_coherent+0xb6/0x120
   ? sst_hsw_dsp_init+0x173/0x420 [snd_soc_sst_haswell_pcm]
   ? mutex_lock+0x9/0x30
   ? kernfs_add_one+0xdb/0x130
   ? devres_add+0x19/0x60
   ? hsw_pcm_dev_probe+0x46/0xd0 [snd_soc_sst_haswell_pcm]
   ? platform_drv_probe+0x30/0x90
   ? driver_probe_device+0x1ed/0x2b0
   ? __driver_attach+0x8f/0xa0
   ? driver_probe_device+0x2b0/0x2b0
   ? bus_for_each_dev+0x55/0x90
   ? bus_add_driver+0x110/0x210
   ? 0xffffffffa11ea000
   ? driver_register+0x52/0xc0
   ? 0xffffffffa11ea000
   ? do_one_initcall+0x32/0x130
   ? free_vmap_area_noflush+0x37/0x70
   ? kmem_cache_alloc+0x88/0xd0
   ? do_init_module+0x51/0x1c4
   ? load_module+0x1ee9/0x2430
   ? show_taint+0x20/0x20
   ? kernel_read_file+0xfd/0x190
   ? SyS_finit_module+0xa3/0xb0
   ? do_syscall_64+0x4a/0xb0
   ? entry_SYSCALL64_slow_path+0x25/0x25
 Code: 78 ff ff ff 4d 85 c0 74 ee 49 8b 5a 10 0f b6 9b e0 00 00 00 41 38 98 e0 00 00 00 77 da 0f b6 eb 49 39 a8 88 00 00 00 72 ce eb 8f <41> f6 82 ab 07 00 00 04 0f 85 76 ff ff ff 0f b6 4d 08 88 0e 49
 RIP  [<ffffffff8132234a>] device_to_iommu+0x11a/0x1a0
  RSP <ffffc90001457a78>
 CR2: 00000000000007ab
 ---[ end trace 16f974b6d58d0aad ]---

Add the missing pointer check.

Fixes: 1c387188 ("iommu/vt-d: Fix IOMMU lookup for SR-IOV Virtual Functions")
Signed-off-by: Koos Vriezen <koos.vriezen@gmail.com>
Cc: stable@vger.kernel.org # 4.8.15+
Signed-off-by: Joerg Roedel <jroedel@suse.de>

This BUG_ON() triggered for me once at shutdown, and I don't see a
reason for the check.  The code correctly checks whether the swap slot
cache is usable or not, so an uninitialized swap slot cache is not
actually problematic afaik.

I've temporarily just switched the BUG_ON() to a WARN_ON_ONCE(), since
I'm not sure why that seemingly pointless check was there.  I suspect
the real fix is to just remove it entirely, but for now we'll warn about
it but not bring the machine down.

Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more powerpc fixes from Michael Ellerman:
 "A couple of minor powerpc fixes for 4.11:

   - wire up statx() syscall

   - don't print a warning on memory hotplug when HPT resizing isn't
     available

  Thanks to: David Gibson, Chandan Rajendra"

* tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries: Don't give a warning when HPT resizing isn't available
  powerpc: Wire up statx() syscall

Pull parisc fixes from Helge Deller:

 - Mikulas Patocka added support for R_PARISC_SECREL32 relocations in
   modules with CONFIG_MODVERSIONS.

 - Dave Anglin optimized the cache flushing for vmap ranges.

 - Arvind Yadav provided a fix for a potential NULL pointer dereference
   in the parisc perf code (and some code cleanups).

 - I wired up the new statx system call, fixed some compiler warnings
   with the access_ok() macro and fixed shutdown code to really halt a
   system at shutdown instead of crashing & rebooting.

* 'parisc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix system shutdown halt
  parisc: perf: Fix potential NULL pointer dereference
  parisc: Avoid compiler warnings with access_ok()
  parisc: Wire up statx system call
  parisc: Optimize flush_kernel_vmap_range and invalidate_kernel_vmap_range
  parisc: support R_PARISC_SECREL32 relocation in modules

Pull SCSI target fixes from Nicholas Bellinger:
 "The bulk of the changes are in qla2xxx target driver code to address
  various issues found during Cavium/QLogic's internal testing (stable
  CC's included), along with a few other stability and smaller
  miscellaneous improvements.

  There are also a couple of different patch sets from Mike Christie,
  which have been a result of his work to use target-core ALUA logic
  together with tcm-user backend driver.

  Finally, a patch to address some long standing issues with
  pass-through SCSI export of TYPE_TAPE + TYPE_MEDIUM_CHANGER devices,
  which will make folks using physical (or virtual) magnetic tape happy"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
  qla2xxx: Update driver version to 9.00.00.00-k
  qla2xxx: Fix delayed response to command for loop mode/direct connect.
  qla2xxx: Change scsi host lookup method.
  qla2xxx: Add DebugFS node to display Port Database
  qla2xxx: Use IOCB interface to submit non-critical MBX.
  qla2xxx: Add async new target notification
  qla2xxx: Export DIF stats via debugfs
  qla2xxx: Improve T10-DIF/PI handling in driver.
  qla2xxx: Allow relogin to proceed if remote login did not finish
  qla2xxx: Fix sess_lock & hardware_lock lock order problem.
  qla2xxx: Fix inadequate lock protection for ABTS.
  qla2xxx: Fix request queue corruption.
  qla2xxx: Fix memory leak for abts processing
  qla2xxx: Allow vref count to timeout on vport delete.
  tcmu: Convert cmd_time_out into backend device attribute
  tcmu: make cmd timeout configurable
  tcmu: add helper to check if dev was configured
  target: fix race during implicit transition work flushes
  target: allow userspace to set state to transitioning
  target: fix ALUA transition timeout handling
  ...

Pull device-dax fixes from Dan Williams:
 "The device-dax driver was not being careful to handle falling back to
  smaller fault-granularity sizes.

  The driver already fails fault attempts that are smaller than the
  device's alignment, but it also needs to handle the cases where a
  larger page mapping could be established. For simplicity of the
  immediate fix the implementation just signals VM_FAULT_FALLBACK until
  fault-size == device-alignment.

  One fix is for -stable to address pmd-to-pte fallback from the
  original implementation, another fix is for the new (introduced in
  4.11-rc1) pud-to-pmd regression, and a typo fix comes along for the
  ride.

  These have received a build success notification from the kbuild
  robot"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  device-dax: fix debug output typo
  device-dax: fix pud fault fallback handling
  device-dax: fix pmd/pte fault fallback handling

Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.

Following commands are being routed through IOCB interface

- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Add routines to support T10 DIF tag.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

The main lock that needs to be held for CMD or TMR submission
to upper layer is the sess_lock. The sess_lock is used to
serialize cmd submission and session deletion. The addition
of hardware_lock being held is not necessary. This patch removes
hardware_lock dependency from CMD/TMR submission.

Use hardware_lock only for error response in this case.

Path1
       CPU0                    CPU1
       ----                    ----
  lock(&(&ha->tgt.sess_lock)->rlock);
                               lock(&(&ha->hardware_lock)->rlock);
                               lock(&(&ha->tgt.sess_lock)->rlock);
  lock(&(&ha->hardware_lock)->rlock);

Path2/deadlock
*** DEADLOCK ***
Call Trace:
dump_stack+0x85/0xc2
print_circular_bug+0x1e3/0x250
__lock_acquire+0x1425/0x1620
lock_acquire+0xbf/0x210
_raw_spin_lock_irqsave+0x53/0x70
qlt_sess_work_fn+0x21d/0x480 [qla2xxx]
process_one_work+0x1f4/0x6e0

Cc: <stable@vger.kernel.org>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reported-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Normally, ABTS is sent to Target Core as Task MGMT command.
In the case of error, qla2xxx needs to send response, hardware_lock
is required to prevent request queue corruption.

Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.

Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Instead of putting cmd_time_out under ../target/core/user_0/foo/control,
which has historically been used by parameters needed for initial
backend device configuration, go ahead and move cmd_time_out into
a backend device attribute.

In order to do this, tcmu_module_init() has been updated to create
a local struct configfs_attribute **tcmu_attrs, that is based upon
the existing passthrough_attrib_attrs along with the new cmd_time_out
attribute.  Once **tcm_attrs has been setup, go ahead and point
it at tcmu_ops->tb_dev_attrib_attrs so it's picked up by target-core.

Also following MNC's previous change, ->cmd_time_out is stored in
milliseconds but exposed via configfs in seconds.  Also, note this
patch restricts the modification of ->cmd_time_out to before +
after the TCMU device has been configured, but not while it has
active fabric exports.

Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

A single daemon could implement multiple types of devices
using multuple types of real devices that may not support
restarting from crashes and/or handling tcmu timeouts. This
makes the cmd timeout configurable, so handlers that do not
support it can turn if off for now.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

This adds a helper to check if the dev was configured. It
will be used in the next patch to prevent updates to some
config settings after the device has been setup.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Pull OpenRISC fixes from Stafford Horne:
 "OpenRISC fixes for build issues that were exposed by kbuild robots
  after 4.11 merge. All from allmodconfig builds. This includes:

   - bug in the handling of 8-byte get_user() calls

   - module build failure due to multile missing symbol exports"

* tag 'openrisc-for-linus' of git://github.com/openrisc/linux:
  openrisc: Export symbols needed by modules
  openrisc: fix issue handling 8 byte get_user calls
  openrisc: xchg: fix `computed is not used` warning

This fixes the following races:

1. core_alua_do_transition_tg_pt could have read
tg_pt_gp_alua_access_state and gone into this if chunk:

if (!explicit &&
        atomic_read(&tg_pt_gp->tg_pt_gp_alua_access_state) ==
           ALUA_ACCESS_STATE_TRANSITION) {

and then core_alua_do_transition_tg_pt_work could update the
state. core_alua_do_transition_tg_pt would then only set
tg_pt_gp_alua_pending_state and the tg_pt_gp_alua_access_state would
not get updated with the second calls state.

2. core_alua_do_transition_tg_pt could be setting
tg_pt_gp_transition_complete while the tg_pt_gp_transition_work
is already completing. core_alua_do_transition_tg_pt then waits on the
completion that will never be called.

To handle these issues, we just call flush_work which will return when
core_alua_do_transition_tg_pt_work has completed so there is no need
to do the complete/wait. And, if core_alua_do_transition_tg_pt_work
was running, instead of trying to sneak in the state change, we just
schedule up another core_alua_do_transition_tg_pt_work call.

Note that this does not handle a possible race where there are multiple
threads call core_alua_do_transition_tg_pt at the same time. I think
we need a mutex in target_tg_pt_gp_alua_access_state_store.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Userspace target_core_user handlers like tcmu-runner may want to set the
ALUA state to transitioning while it does implicit transitions. This
patch allows that state when set from configfs.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

The implicit transition time tells initiators the min time
to wait before timing out a transition. We currently schedule
the transition to occur in tg_pt_gp_implicit_trans_secs
seconds so there is no room for delays. If
core_alua_do_transition_tg_pt_work->core_alua_update_tpg_primary_metadata
needs to write out info to a remote file, then the initiator can
easily time out the operation.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

If tcmu-runner is processing a STPG and needs to change the kernel's
ALUA state then we cannot use the same work queue for task management
requests and ALUA transitions, because we could deadlock. The problem
occurs when a STPG times out before tcmu-runner is able to
call into target_tg_pt_gp_alua_access_state_store->
core_alua_do_port_transition -> core_alua_do_transition_tg_pt ->
queue_work. In this case, the tmr is on the work queue waiting for
the STPG to complete, but the STPG transition is now queued behind
the waiting tmr.

Note:
This bug will also be fixed by this patch:
http://www.spinics.net/lists/target-devel/msg14560.html
which switches the tmr code to use the system workqueues.

For both, I am not sure if we need a dedicated workqueue since
it is not a performance path and I do not think we need WQ_MEM_RECLAIM
to make forward progress to free up memory like the block layer does.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

We do not setup the LU group for pscsi devices, so if you write
a state to alua_access_state that will cause a transition you will
get a NULL pointer dereference.

This patch will fail attempts to try and transition the path
for backend devices that set the TRANSPORT_FLAG_PASSTHROUGH_ALUA
flag.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>