commit cf0d53ba upstream.

MRRS defines the maximum read request size a device is allowed to
make.  Drivers will often increase this to allow more data transfer
with a single request.  Completions to this request are bound by the
MPS setting for the bus.  Aside from device quirks (none known), it
doesn't seem to make sense to set an MRRS value less than MPS, yet
this is a likely scenario given that user drivers do not have a
system-wide view of the PCI topology.  Virtualize MRRS such that the
user can set MRRS >= MPS, but use MPS as the floor value that we'll
write to hardware.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 977f6f68 upstream.

F71808FG_FLAG_WD_EN defines bit position, not a bitmask
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 55a5fcaf upstream.

Just add binding for a fixed-factor clock axisel_d4, which would be
referenced by PWM devices on MT7623 or MT2701 SoC.

Cc: stable@vger.kernel.org
Fixes: 1de9b216 ("clk: mediatek: Add dt-bindings for MT2701 clocks")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cf1ba1d7 upstream.

When device boots with T > T_trip_1 and requests interrupt,
the race condition takes place. The interrupt comes before
THERMAL_DEVICE_ENABLED is set. This leads to an attempt to
reading sensor value from irq and disabling the sensor, based on
the data->mode field, which expected to be THERMAL_DEVICE_ENABLED,
but still stays as THERMAL_DEVICE_DISABLED. Afher this issue
sensor is never re-enabled, as the driver state is wrong.

Fix this problem by setting the 'data' members prior to
requesting the interrupts.

Fixes: 37713a1e ("thermal: imx: implement thermal alarm interrupt handling")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mikhail Lappo <mikhail.lappo@esrlabs.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6225f9c6 upstream.

This patch fixes an issue that is possible to set mismatch value to duty
for R-Car PWM if we input the following commands:

 # cd /sys/class/pwm/<pwmchip>/
 # echo 0 > export
 # cd pwm0
 # echo 30 > period
 # echo 30 > duty_cycle
 # echo 0 > duty_cycle
 # cat duty_cycle
 0
 # echo 1 > enable
 --> Then, the actual duty_cycle is 30, not 0.

So, this patch adds a condition into rcar_pwm_config() to fix this
issue.
Signed-off-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
[shimoda: revise the commit log and add Fixes and Cc tags]
Fixes: ed6c1476 ("pwm: Add support for R-Car PWM Timer")
Cc: Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 75387237 upstream.

In order to enable a PLL, not only the PLL has to be powered up and
locked, but you also have to de-assert the reset signal. The last part
was missing. Add it so PLLs that were not enabled by the FW/bootloader
can be enabled from Linux.

Fixes: 41691b88 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ce33f284 upstream.

When we build this driver with on x86-32, gcc produces a false-positive warning:

drivers/clk/renesas/clk-sh73a0.c: In function 'sh73a0_cpg_clocks_init':
drivers/clk/renesas/clk-sh73a0.c:155:10: error: 'parent_name' may be used uninitialized in this function [-Werror=maybe-uninitialized]
   return clk_register_fixed_factor(NULL, name, parent_name, 0,

We can work around that warning by adding a fake initialization, I tried
and failed to come up with any better workaround. This is currently one
of few remaining warnings for a 4.14.y randconfig build, so it would be
good to also have it backported at least to that version. Older versions
have more randconfig warnings, so we might not care.

I had not noticed this earlier, because one patch in my randconfig test
tree removes the '-ffreestanding' option on x86-32, and that avoids
the warning. The -ffreestanding flag was originally global but moved
into arch/i386 by Andi Kleen in commit 6edfba1b ("[PATCH] x86_64:
Don't define string functions to builtin") as a 'temporary workaround'.

Like many temporary hacks, this turned out to be rather long-lived, from
all I can tell we still need a simple fix to asm/string_32.h before it
can be removed, but I'm not sure about how to best do that.

Cc: stable@vger.kernel.org
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6a4a4595 upstream.

Clearfog boards can come with a CPU clocked at 1600MHz (commercial)
or 1333MHz (industrial).

They have also some dip-switches to select a different clock (666, 800,
1066, 1200).

The funny thing is that the recovery button is on the MPP34 fq selector.
So, when booting an industrial board with this button down, the frequency
666MHz is selected (and the kernel didn't boot).

This patch add all the missing clocks.

The only mode I didn't test is 2GHz (uboot found 4294MHz instead :/ ).

Fixes: 0e85aece ("clk: mvebu: add clock support for Armada 380/385")
Cc: <stable@vger.kernel.org> # 3.16.x: 9593f4f5: clk: mvebu: armada-38x: add support for 1866MHz variants
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9593f4f5 upstream.

The Linksys WRT3200ACM CPU is clocked at 1866MHz. Add 1866MHz to the
list of supported CPU frequencies. Also update multiplier and divisor
for the l2clk and ddrclk.

Noticed by the following warning:
[    0.000000] Selected CPU frequency (16) unsupported
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a04f0017 upstream.

A spinlock is held while updating the internal copy of the IRQ mask,
but not while writing it to the actual IMASK register. After the lock
is released, an IRQ can occur before the IMASK register is written.
If handling this IRQ causes the mask to be changed, when the handler
returns back to the middle of the first mask update, a stale value
will be written to the mask register.

If this causes an IRQ to become unmasked that cannot have its status
cleared by writing a 1 to it in the IREG register, e.g. the SDIO IRQ,
then we can end up stuck with the same IRQ repeatedly being fired but
not handled. Normally the MMC IRQ handler attempts to clear any
unexpected IRQs by writing IREG, but for those that cannot be cleared
in this way then the IRQ will just repeatedly fire.

This was resulting in lockups after a while of using Wi-Fi on the
CI20 (GitHub issue #19).

Resolve by holding the spinlock until after the IMASK register has
been updated.

Cc: stable@vger.kernel.org
Link: https://github.com/MIPS/CI20_linux/issues/19
Fixes: 61bfbdb8 ("MMC: Add support for the controller on JZ4740 SoCs.")
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bbe4b3af upstream.

A memory block was allocated in intel_svm_bind_mm() but never freed
in a failure path. This patch fixes this by free it to avoid memory
leakage.

Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Fixes: 2f26e0a9 ('iommu/vt-d: Add basic SVM PASID support')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4d1a535b upstream.

glibc 2.26 removed the 'struct ucontext' to "improve" POSIX compliance
and break programs, including User Mode Linux. Fix User Mode Linux
by using POSIX ucontext_t.

This fixes:

arch/um/os-Linux/signal.c: In function 'hard_handler':
arch/um/os-Linux/signal.c:163:22: error: dereferencing pointer to incomplete type 'struct ucontext'
  mcontext_t *mc = &uc->uc_mcontext;
arch/x86/um/stub_segv.c: In function 'stub_segv_handler':
arch/x86/um/stub_segv.c:16:13: error: dereferencing pointer to incomplete type 'struct ucontext'
          &uc->uc_mcontext);

Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 530ba6c7 upstream.

Recent libcs have gotten a bit more strict, so we actually need to
include the right headers and use the right types. This enables UML to
compile again.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 78727137 upstream.

There is a small window whereby ARS scan requests can schedule work that
userspace will miss when polling scrub_show. Hold the init_mutex lock
over calls to report the status to close this potential escape. Also,
make sure that requests to cancel the ARS workqueue are treated as an
idle event.

Cc: <stable@vger.kernel.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Fixes: 37b137ff ("nfit, libnvdimm: allow an ARS scrub...")
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4f867220 upstream.

The following NULL dereference results from incorrectly assuming that
ndd is valid in this print:

  struct nvdimm_drvdata *ndd = to_ndd(&nd_region->mapping[i]);

  /*
   * Give up if we don't find an instance of a uuid at each
   * position (from 0 to nd_region->ndr_mappings - 1), or if we
   * find a dimm with two instances of the same uuid.
   */
  dev_err(&nd_region->dev, "%s missing label for %pUb\n",
                  dev_name(ndd->dev), nd_label->uuid);

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
 IP: nd_region_register_namespaces+0xd67/0x13c0 [libnvdimm]
 PGD 0 P4D 0
 Oops: 0000 [#1] SMP PTI
 CPU: 43 PID: 673 Comm: kworker/u609:10 Not tainted 4.16.0-rc4+ #1
 [..]
 RIP: 0010:nd_region_register_namespaces+0xd67/0x13c0 [libnvdimm]
 [..]
 Call Trace:
  ? devres_add+0x2f/0x40
  ? devm_kmalloc+0x52/0x60
  ? nd_region_activate+0x9c/0x320 [libnvdimm]
  nd_region_probe+0x94/0x260 [libnvdimm]
  ? kernfs_add_one+0xe4/0x130
  nvdimm_bus_probe+0x63/0x100 [libnvdimm]

Switch to using the nvdimm device directly.

Fixes: 0e3b0d12 ("libnvdimm, namespace: allow multiple pmem...")
Cc: <stable@vger.kernel.org>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c5637476 upstream.

Despite the efforts made to correctly read the NDA and CUBC registers,
the order in which the registers are read could sometimes lead to an
inconsistent state.

Re-using the timeline from the comments, this following timing of
registers reads could lead to reading NDA with value "@desc2" and
CUBC with value "MAX desc1":

 INITD --------                    ------------
              |____________________|
       _______________________  _______________
 NDA       @desc2             \/   @desc3
       _______________________/\_______________
       __________  ___________  _______________
 CUBC       0    \/ MAX desc1 \/  MAX desc2
       __________/\___________/\_______________
        |  |          |  |
Events:(1)(2)        (3)(4)

(1) check_nda = @desc2
(2) initd = 1
(3) cur_ubc = MAX desc1
(4) cur_nda = @desc2

This is allowed by the condition ((check_nda == cur_nda) && initd),
despite cur_ubc and cur_nda being in the precise state we don't want.

This error leads to incorrect residue computation.

Fix it by inversing the order in which CUBC and INITD are read. This
makes sure that NDA and CUBC are always read together either _before_
INITD goes to 0 or _after_ it is back at 1.
The case where NDA is read before INITD is at 0 and CUBC is read after
INITD is back at 1 will be rejected by check_nda and cur_nda being
different.

Fixes: 53398f48 ("dmaengine: at_xdmac: fix residue corruption")
Cc: stable@vger.kernel.org
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3a148896 upstream.

Ensure that cv_end is equal to ibdev->num_comp_vectors for the
NUMA node with the highest index. This patch improves spreading
of RDMA channels over completion vectors and thereby improves
performance, especially on systems with only a single NUMA node.
This patch drops support for the comp_vector login parameter by
ignoring the value of that parameter since I have not found a
good way to combine support for that parameter and automatic
spreading of RDMA channels over completion vectors.

Fixes: d92c0da7 ("IB/srp: Add multichannel support")
Reported-by: Alexander Schmid <alex@modula-shop-systems.de>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Alexander Schmid <alex@modula-shop-systems.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e68088e7 upstream.

Before commit e494f6a7 ("[SCSI] improved eh timeout handler") it
did not really matter whether or not abort handlers like srp_abort()
called .scsi_done() when returning another value than SUCCESS. Since
that commit however this matters. Hence only call .scsi_done() when
returning SUCCESS.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a820ccbe upstream.

The PCM runtime object is created and freed dynamically at PCM stream
open / close time.  This is tracked via substream->runtime, and it's
cleared at snd_pcm_detach_substream().

The runtime object assignment is protected by PCM open_mutex, so for
all PCM operations, it's safely handled.  However, each PCM substream
provides also an ALSA timer interface, and user-space can access to
this while closing a PCM substream.  This may eventually lead to a
UAF, as snd_pcm_timer_resolution() tries to access the runtime while
clearing it in other side.

Fortunately, it's the only concurrent access from the PCM timer, and
it merely reads runtime->timer_resolution field.  So, we can avoid the
race by reordering kfree() and wrapping the substream->runtime
clearance with the corresponding timer lock.

Reported-by: syzbot+8e62ff4e07aa2ce87826@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a6544a62 upstream.

This patch avoids that KASAN reports the following when the SRP initiator
calls srp_post_send():

==================================================================
BUG: KASAN: stack-out-of-bounds in rxe_post_send+0x5c4/0x980 [rdma_rxe]
Read of size 8 at addr ffff880066606e30 by task 02-mq/1074

CPU: 2 PID: 1074 Comm: 02-mq Not tainted 4.16.0-rc3-dbg+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
Call Trace:
dump_stack+0x85/0xc7
print_address_description+0x65/0x270
kasan_report+0x231/0x350
rxe_post_send+0x5c4/0x980 [rdma_rxe]
srp_post_send.isra.16+0x149/0x190 [ib_srp]
srp_queuecommand+0x94d/0x1670 [ib_srp]
scsi_dispatch_cmd+0x1c2/0x550 [scsi_mod]
scsi_queue_rq+0x843/0xa70 [scsi_mod]
blk_mq_dispatch_rq_list+0x143/0xac0
blk_mq_do_dispatch_ctx+0x1c5/0x260
blk_mq_sched_dispatch_requests+0x2bf/0x2f0
__blk_mq_run_hw_queue+0xdb/0x160
__blk_mq_delay_run_hw_queue+0xba/0x100
blk_mq_run_hw_queue+0xf2/0x190
blk_mq_sched_insert_request+0x163/0x2f0
blk_execute_rq+0xb0/0x130
scsi_execute+0x14e/0x260 [scsi_mod]
scsi_probe_and_add_lun+0x366/0x13d0 [scsi_mod]
__scsi_scan_target+0x18a/0x810 [scsi_mod]
scsi_scan_target+0x11e/0x130 [scsi_mod]
srp_create_target+0x1522/0x19e0 [ib_srp]
kernfs_fop_write+0x180/0x210
__vfs_write+0xb1/0x2e0
vfs_write+0xf6/0x250
SyS_write+0x99/0x110
do_syscall_64+0xee/0x2b0
entry_SYSCALL_64_after_hwframe+0x42/0xb7

The buggy address belongs to the page:
page:ffffea0001998180 count:0 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0x4000000000000000()
raw: 4000000000000000 0000000000000000 0000000000000000 00000000ffffffff
raw: dead000000000100 dead000000000200 0000000000000000 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
ffff880066606d00: 00 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1
ffff880066606d80: f1 00 f2 f2 f2 f2 f2 f2 f2 00 00 f2 f2 f2 f2 f2
>ffff880066606e00: f2 00 00 00 00 00 f2 f2 f2 f3 f3 f3 f3 00 00 00
                                    ^
ffff880066606e80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff880066606f00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
==================================================================

Fixes: 8700e3e7 ("Soft RoCE driver")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Moni Shoua <monis@mellanox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8435168d upstream.

Check to make sure that ctx->cm_id->device is set before we use it.
Otherwise userspace can trigger a NULL dereference by doing
RDMA_USER_CM_CMD_SET_OPTION on an ID that is not bound to a device.

Cc: <stable@vger.kernel.org>
Reported-by: <syzbot+a67bc93e14682d92fc2f@syzkaller.appspotmail.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8e4b5eae upstream.

If the root directory has an i_links_count of zero, then when the file
system is mounted, then when ext4_fill_super() notices the problem and
tries to call iput() the root directory in the error return path,
ext4_evict_inode() will try to free the inode on disk, before all of
the file system structures are set up, and this will result in an OOPS
caused by a NULL pointer dereference.

This issue has been assigned CVE-2018-1092.

https://bugzilla.kernel.org/show_bug.cgi?id=199179
https://bugzilla.redhat.com/show_bug.cgi?id=1560777Reported-by: Wen Xu <wen.xu@gatech.edu>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 73fdad00 upstream.

i_disksize update should be protected by i_data_sem, by either taking
the lock explicitly or by using ext4_update_i_disksize() helper. But the
i_disksize updates in ext4_direct_IO_write() are not protected at all,
which may be racing with i_disksize updates in writeback path in
delalloc buffer write path.

This is found by code inspection, and I didn't hit any i_disksize
corruption due to this bug. Thanks to Jan Kara for catching this bug and
suggesting the fix!
Reported-by: Jan Kara <jack@suse.cz>
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 044e6e3d upstream.

When reading the inode or block allocation bitmap, if the bitmap needs
to be initialized, do not update the checksum in the block group
descriptor.  That's because we're not set up to journal those changes.
Instead, just set the verified bit on the bitmap block, so that it's
not necessary to validate the checksum.

When a block or inode allocation actually happens, at that point the
checksum will be calculated, and update of the bg descriptor block
will be properly journalled.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 85e0c4e8 upstream.

This updates the jbd2 superblock unnecessarily, and on an abort we
shouldn't truncate the log.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9f886f4d upstream.

This fixes a harmless UBSAN where root could potentially end up
causing an overflow while bumping the entropy_total field (which is
ignored once the entropy pool has been initialized, and this generally
is completed during the boot sequence).

This is marginal for the stable kernel series, but it's a really
trivial patch, and it fixes UBSAN warning that might cause security
folks to get overly excited for no reason.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Chen Feng <puck.chen@hisilicon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit aa08192a upstream.

Most MMIO GIC register accesses use a 1-hot bit scheme that
avoids requiring any form of locking. This isn't true for the
GICD_ICFGRn registers, which require a RMW sequence.

Unfortunately, we seem to be missing a lock for these particular
accesses, which could result in a race condition if changing the
trigger type on any two interrupts within the same set of 16
interrupts (and thus controlled by the same CFGR register).

Introduce a private lock in the GIC common comde for this
particular case, making it cover both GIC implementations
in one go.

Cc: stable@vger.kernel.org
Signed-off-by: Aniruddha Banerjee <aniruddhab@nvidia.com>
[maz: updated changelog]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f2a659f7 upstream.

The driver misses implementation of PM hook that undoes what
->freeze_noirq() does after the hibernation image is created. This means
the control channel is not resumed properly and the Thunderbolt bus
becomes useless in later stages of hibernation (when the image is stored
or if the operation fails).

Fix this by pointing ->thaw_noirq to driver nhi_resume_noirq(). This
makes sure the control channel is resumed properly.

Fixes: 23dd5bb4 ("thunderbolt: Add suspend/hibernate support")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a01df75c upstream.

SSM2602 driver is broken on recent kernels (at least
since 4.9). User space applications such as amixer or
alsamixer get EIO when attempting to access codec
controls via the relevant IOCTLs.

Root cause of these failures is the regcache_hw_init
function in drivers/base/regmap/regcache.c, which
prevents regmap cache initalization from the
reg_defaults_raw element of the regmap_config structure
when registers are write only. It also disables the
regmap cache entirely when all registers are write only
or volatile as is the case for the SSM2602 driver.

Using the reg_defaults element of the regmap_config
structure rather than the reg_defaults_raw element to
initalize the regmap cache avoids the logic in the
regcache_hw_init function entirely. It also makes this
driver consistent with other ASoC codec drivers, as
this driver was the ONLY codec driver that used the
reg_defaults_raw element to initalize the cache.

Tested on Digilent Zybo Z7 development board which has
a SSM2603 codec chip connected to a Xilinx Zynq SoC.
Signed-off-by: James Kelly <jamespeterkelly@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6de0b13c upstream.

When size is negative, calling memset will make segment fault.
Declare the size as type u32 to keep memset safe.

size in struct hid_report is unsigned, fix return type of
hid_report_len to u32.

Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3064a03b upstream.

Follow the change of return type u32 of hid_report_len,
fix all the types of variables those get the return value of
hid_report_len to u32, and all other code already uses u32.

Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3b807033 upstream.

The OPAL NVRAM driver does not sleep in case it gets OPAL_BUSY or
OPAL_BUSY_EVENT from firmware, which causes large scheduling
latencies, and various lockup errors to trigger (again, BMC reboot
can cause it).

Fix this by converting it to the standard form OPAL_BUSY loop that
sleeps.

Fixes: 628daa8d ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Depends-on: 34dd25de ("powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 34dd25de upstream.

This is the start of an effort to tidy up and standardise all the
delays. Existing loops have a range of delay/sleep periods from 1ms
to 20ms, and some have no delay. They all loop forever except rtc,
which times out after 10 retries, and that uses 10ms delays. So use
10ms as our standard delay. The OPAL maintainer agrees 10ms is a
reasonable starting point.

The idea is to use the same recipe everywhere, once this is proven to
work then it will be documented as an OPAL API standard. Then both
firmware and OS can agree, and if a particular call needs something
else, then that can be documented with reasoning.

This is not the end-all of this effort, it's just a relatively easy
change that fixes some existing high latency delays. There should be
provision for standardising timeouts and/or interruptible loops where
possible, so non-fatal firmware errors don't cause hangs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0bfdf598 upstream.

asm/barrier.h is not always included after asm/synch.h, which meant
it was missing __SUBARCH_HAS_LWSYNC, so in some files smp_wmb() would
be eieio when it should be lwsync. kernel/time/hrtimer.c is one case.

__SUBARCH_HAS_LWSYNC is only used in one place, so just fold it in
to where it's used. Previously with my small simulator config, 377
instances of eieio in the tree. After this patch there are 55.

Fixes: 46d075be ("powerpc: Optimise smp_wmb")
Cc: stable@vger.kernel.org # v2.6.29+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 741de617 upstream.

opal_nvram_write currently just assumes success if it encounters an
error other than OPAL_BUSY or OPAL_BUSY_EVENT. Have it return -EIO
on other errors instead.

Fixes: 628daa8d ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ac75a041 upstream.

When convert char array with signed int, if the inbuf[x] is negative then
upper bits will be set to 1. Fix this by using u8 instead of char.

ret_size has to be at least 3, hid_input_report use it after minus 2 bytes.

Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7ea884c7 upstream.

Some servers return inode number zero for the root directory, which
causes ls to display incorrect data (missing "." and "..").

If the server returns zero for the inode number of the root directory,
fake an inode number for it.
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cabdf83d upstream.

Platform device is allocated before adding resources. Make sure to
properly cleanup on error case.

Cc: <stable@vger.kernel.org>
Fixes: f1c7e710 ("usb: dwc3: convert to pcim_enable_device()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 64627388 upstream.

USB3 hubs don't support global suspend.

USB3 specification 10.10, Enhanced SuperSpeed hubs only support selective
suspend and resume, they do not support global suspend/resume where the
hub downstream facing ports states are not affected.

When system enters hibernation it first enters freeze process where only
the root hub enters suspend, usb_port_suspend() is not called for other
devices, and suspend status flags are not set for them. Other devices are
expected to suspend globally. Some external USB3 hubs will suspend the
downstream facing port at global suspend. These devices won't be resumed
at thaw as the suspend status flag is not set.

A USB3 removable hard disk connected through a USB3 hub that won't resume
at thaw will fail to synchronize SCSI cache, return “cmd cmplt err -71”
error, and needs a 60 seconds timeout which causing system hang for 60s
before the USB host reset the port for the USB3 removable hard disk to
recover.

Fix this by always calling usb_port_suspend() during freeze for USB3
devices.
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7fafcfdf upstream.

It looks like there is a possibility of a double-free vulnerability on an
error path of the f_midi_set_alt function in the f_midi driver. If the
path is feasible then free_ep_req gets called twice:

         req->complete = f_midi_complete;
         err = usb_ep_queue(midi->out_ep, req, GFP_ATOMIC);
            => ...
             usb_gadget_giveback_request
               =>
                 f_midi_complete (CALLBACK)
                   (inside f_midi_complete, for various cases of status)
                   free_ep_req(ep, req); // first kfree
         if (err) {
                 ERROR(midi, "%s: couldn't enqueue request: %d\n",
                             midi->out_ep->name, err);
                 free_ep_req(midi->out_ep, req); // second kfree
                 return err;
         }

The double-free possibility was introduced with commit ad0d1a05
("usb: gadget: f_midi: fix leak on failed to enqueue out requests").

Found by MOXCAFE tool.
Signed-off-by: Tuba Yavuz <tuba@ece.ufl.edu>
Fixes: ad0d1a05 ("usb: gadget: f_midi: fix leak on failed to enqueue out requests")
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>