- 16 Oct, 2007 40 commits
-
-
Andres Salomon authored
According to 6.3.2.7 of the cs5535/cs5536 data sheets, the ACC_BM[x]_CMD registers are only 8 bits wide. This driver treats them as 32 bits wide, and also has bits in the wrong place. Simple fix to the definitions. Signed-off-by:
Andres Salomon <dilinger@debian.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Jaroslav Kysela <perex@suse.cz>
-
Andres Salomon authored
Save the PCI state before disabling the device, and add some error checking. Signed-off-by:
-
Andres Salomon authored
In the suspend path, we currently save the PRD registers and then disable DMA. This is racy; the sound hardware might update the PRD register as it finishes processing some DMA pages between when we've saved the PRD registers and when DMA actually gets disabled. Furthermore, we actively check whether or not DMA is enabled before saving PRD registers; there's no reason to do that, as the PRD registers should not update when we twiddle the ACC_BM[x]_CMD register(s). Worst case, we save the PRD registers twice; even powering down the ACC shouldn't mess with the PRD registers (according to the 5536 data sheet, section 5.3.7.4, power-down procedure). This patch reworks all that to first disable DMA, and then save PRD registers. Signed-off-by:
-
Andres Salomon authored
We're never actually setting dma->substream to the current substream; that means the dma->substream checks that we do in the suspend/resume path are never satisfied, and the PRD registers are never correctly managed. This changes it so that we set the substream when constructing the specific bus master DMA, and unsetting it when we tear down the BM's DMA. Signed-off-by:
-
Maxim Levitsky authored
1) Create seperate mixer controls for each ADC 2) Make number of substreams of capture PCM device be equal to number of ADCs Signed-off-by:
Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by:
-
Maxim Levitsky authored
VolumeKnob is present on most sigmatel codecs, it allows to decrease volume of all DACs at once, it is a kind of post-procesing volume. Note that all output amps of sigmatel only decrease volume, and all input amps only increase volume. Signed-off-by:
-
Maxim Levitsky authored
The analog loopback routes the sound just before it enters ADC0 to output of DAC0. Signed-off-by:
-
Maxim Levitsky authored
Center/LFE channels are located on same jack, so it can be usefull to swap them. Signed-off-by:
-
Maxim Levitsky authored
Comment in hda_intel.c states that 'the explicit resume is needed only when POWER_SAVE isn't set', but this is not true. There is no code that will automaticly power up the codec on resume, but only code that powers it up when user accesses it. So if user leaves a sound playing, codec will not be powered To fix that I check if there are any codecs that should be powered codec->power_count, and if so I power them up together with main controller. Signed-off-by:
-
Maxim Levitsky authored
codec->power_transition is supposed to be true while codec is going to be shut off if in the mean time somebody calls snd_hda_power_up, hda_power_work will not shut down the codec, but nether will clear codec->power_transition, thus it stays on forever. Fix this. Signed-off-by:
-
Clemens Ladisch authored
The '-MCx' suffix that is expected by alsa-lib is only needed in the card driver string, so we can show the actual chip name in the shortname. Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
-
Clemens Ladisch authored
Check that the UART_EN bit actually enabled the MPU-401 port. Apparently, C-Media thinks that it is a good idea to be paranoid here. Signed-off-by:
-
Clemens Ladisch authored
Integrated MPU-401/OPL3 ports are available with chip version 39 and later, so we do not test for the port with version 37. Now that the test is known to work, we can again enable the MIDI port by default. Signed-off-by:
-
Clemens Ladisch authored
Add support for 88.2 kHz and 96 kHz analog and digital playback on CMI8768/CMI8770 chips. Signed-off-by:
-
Clemens Ladisch authored
Remove the constraint that sets the channel limit for the first playback device to that of the second one; the first device supports only stereo. Signed-off-by:
-
Takashi Iwai authored
The STAC codes adds line_out_pins[] for shared mic/line-inputs accordingly. But, the current code may give a hole with NID=0 in some setting, which results in an error at probe. This patch fixes the problem. Signed-off-by:
-
Takashi Iwai authored
The resume procedure for STAC codecs overrides the cached values and results in the wrong (reset) PIN state. The patch gets rid of the overriding part and simplifies the resume. Signed-off-by:
-
Mark Hills authored
Allow the interface's mixer to be used, and give the interface its correct name. Signed-off-by:
Mark Hills <mark@pogo.org.uk> Signed-off-by:
-
Maxim Levitsky authored
Clean up the mixer entries for Input Source using a macro. Signed-off-by:
-
zhejiang authored
Fix the index for Front Mic capture source on ALC262 HP machines. Also, added the new capture source list for HP BPC DC7000 series to work properly. From: zhejiang <zhe.jiang@intel.com> Signed-off-by:
-
Remy Bruno authored
added support for the latest revision of the 9632 (and hopefully a few following ones). The DSP matrix was not working because of wrong identification of the card in this part of the code. Signed-off-by:
Remy Bruno <remy.bruno@trinnov.com> Signed-off-by:
-
Remy Bruno authored
* better report of speed mode change failures * autosync_ref control bugfix (was reporting pref_sync_ref instead) (changed HDSPM_AES32_AUTOSYNC_FROM_NONE value to comply with array indexing in snd_hdspm_info_autosync_ref()) * added support for master modes up to 192kHz (clock source control value was restricted up to 96kHz) Signed-off-by:
-
Oliver Neukum authored
usb_set_interface() can fail, even for altsetting 0 Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Clemens Ladisch authored
Add a quirk to detect the Serato Scratch Live DJ Box. Signed-off-by:
-
Takashi Iwai authored
On codec chips with both audio and modem functions (e.g. Conexant one), performing AC97_RESET resets the whole registers. When both audio and modem drivers are resumed at the same time, the modem one often is resumed after the audio, and it results in the reset of audio registers (ALSA bug#3333). This patch fixes such a problem. Since the modem codec basically doesn't need AC97_RESET, skip this initialization unless specified as audio. Signed-off-by:
-
Takashi Iwai authored
Some codecs need Mic Boost mixer controls for obtaining a proper recording level, but the auto-configuration doesn't create them. This patch adds the creation of mic-boost controls on corresponding codecs. Signed-off-by:
-
Takashi Iwai authored
CS5530 is a PCI device and often shares the IRQ although the SB common routine tries to allocate it exclusively. This patch allows shared IRQ for CS5530. Signed-off-by:
-
Jesper Juhl authored
vmalloc() returns void *. no need to cast. Signed-off-by:
Jesper Juhl <jesper.juhl@gmail.com> Signed-off-by:
-
Clemens Ladisch authored
Show the actual name of CMI8762/CMI8768/CMI8769/CMI8770 chips in the card longname instead of just using 'CMI8738' for all of them. Signed-off-by:
-
Clemens Ladisch authored
Remove the has_dual_dac variable because it was always set. Signed-off-by:
-
Clemens Ladisch authored
Add a case for chip version 39 where no bit is set in register 0Ch, and move the detection of version 39 before that of 8768. This makes the logic more compatible with the driver on that other OS. Signed-off-by:
-
Clemens Ladisch authored
Unused bytes in the I/O register range are likely to have the value 0x00 instead of 0xff, so test against both values when checking for the presence of the integrated MIDI port. Signed-off-by:
-
Takashi Iwai authored
Fixed Dell laptops support with STAC92xx codecs. Many pin-config models are introduced. See ALSA-Configuration.txt for details. The patch taken from ALSA bug#3319, originally by Jorg Prante: https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3319Signed-off-by:
-
Takashi Iwai authored
The unsol event of ALC268 is in the standard bit 26. Also, fixed the Acer master controls, and added Extensa 5210 to the quirk list. Signed-off-by:
-
Takashi Iwai authored
Fixed the master mixer switch of ALC272 sony-amd model. It used a simple bind-control, but it resulted in unexpected unmute of speaker output. Now the control checks the HP jack state apropriately, just like fujitsu model. Signed-off-by:
-
Takashi Iwai authored
gcc-3.x doesn't like forward inlining: CC [M] sound/pci/hda/hda_codec.o sound/pci/hda/hda_codec.c: In function 'snd_hda_codec_free': sound/pci/hda/hda_codec.c:517: sorry, unimplemented: inlining failed in call to 'free_hda_cache': function body not available sound/pci/hda/hda_codec.c:534: sorry, unimplemented: called from here sound/pci/hda/hda_codec.c:517: sorry, unimplemented: inlining failed in call to 'free_hda_cache': function body not available sound/pci/hda/hda_codec.c:535: sorry, unimplemented: called from here Signed-off-by:
-
Takashi Iwai authored
Added the PCI ID entries for known working devices - Prolink PixelView PV-M4900 - Pinnacle Studio PCTV rave Signed-off-by:
-
Clemens Ladisch authored
Make sure that the MPU-401 MIDI and OPL-3 FM devices are used only on those chips where they are supported, and that the correct port addresses are used. Signed-off-by:
-
Takashi Iwai authored
Use the standard firmware loader for loading ICS2115 OS firmware file. This is the last old bad guy that is still using sys_open() and sys_read() calls, and now all should be gone. The patch also adds the missing description of module options related with wavefront_synth.c. Due to this rewrite, user will have to copy or make symlink the firmware file appropriately to the standard firmware path such as /lib/firmware. Signed-off-by:
-
Takashi Iwai authored
Added missing capture boost controls for ALC268 codec. Signed-off-by:
-
