- 09 Jun, 2006 7 commits
-
-
John Rose authored
This patch attempts to handle RTAS "busy" return codes in a more simple and consistent manner. Typical callers of RTAS shouldn't have to manage wait times and delay calls. This patch also changes the kernel to use msleep() rather than udelay() when a runtime delay is necessary. This will avoid CPU soft lockups for extended delay conditions. Signed-off-by: John Rose <johnrose@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
-
Andrew Morton authored
From: Andrew Morton <akpm@osdl.org> arch/powerpc/Kconfig:339:warning: leading whitespace ignored arch/powerpc/Kconfig:347:warning: leading whitespace ignored arch/powerpc/Kconfig:357:warning: leading whitespace ignored arch/powerpc/Kconfig:373:warning: leading whitespace ignored arch/powerpc/Kconfig:382:warning: leading whitespace ignored arch/powerpc/Kconfig:394:warning: leading whitespace ignored arch/powerpc/Kconfig:842:warning: leading whitespace ignored arch/powerpc/Kconfig:847:warning: leading whitespace ignored Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
-
Anton Blanchard authored
The 970MP cputable entry needs a num_pmcs entry for oprofile to work. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
-
Will Schmidt authored
My js20 appears to lack the ibm,#dma- properties, and boot fails with a "Kernel panic - not syncing: iommu_init_table: Can't allocate 0 bytes" message. This adds a fallback to the "#address-cells" property in case the "#ibm,dma-address-cells" property is missing. Tested on js20 and power5 lpar. Unless there is a more elegant solution... :-) Signed-off-by: Will Schmidt <willschm@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
-
Benjamin Herrenschmidt authored
Our MMU hash management code would not set the "C" bit (changed bit) in the hardware PTE when updating a RO PTE into a RW PTE. That would cause the hardware to possibly to a write back to the hash table to set it on the first store access, which in addition to being a performance issue, might also hit a bug when running with native hash management (non-HV) as our code is specifically optimized for the case where no write back happens. Thus there is a very small therocial window were a hash PTE can become corrupted if that HPTE has just been upgraded to read write, a store access happens on it, and that races with another processor evicting that same slot. Since eviction (caused by an almost full hash) is extremely rare, the bug is very unlikely to happen fortunately. This fixes by allowing the updating of the protection bits in the native hash handling to also set (but not clear) the "C" bit, and, in order to also improve performances in the general case, by always setting that bit on newly inserted hash PTE so that writeback really never happens. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
-
Benjamin Herrenschmidt authored
This patch cleans up some locking & error handling in the ppc vdso and moves the vdso base pointer from the thread struct to the mm context where it more logically belongs. It brings the powerpc implementation closer to Ingo's new x86 one and also adds an arch_vma_name() function allowing to print [vsdo] in /proc/<pid>/maps if Ingo's x86 vdso patch is also applied. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
-
Renzo Davoli authored
I have tested PPC_PTRACE_GETREGS and PPC_PTRACE_SETREGS on umview. I do not understand why historically these tags has been defined as PPC_PTRACE_GETREGS and PPC_PTRACE_SETREGS instead of simply PTRACE_[GS]ETREGS. The other "originality" is that the address must be put into the "addr" field instead of the "data" field as stated in the manual. Signed-off-by: renzo davoli <renzo@cs.unibo.it> Signed-off-by: Paul Mackerras <paulus@samba.org>
-
- 01 Jun, 2006 1 commit
-
-
Paul Mackerras authored
-
- 31 May, 2006 32 commits
-
-
git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds authored
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: [MIPS] Treat R14000 like R10000. [MIPS] Remove EXPERIMENTAL from PAGE_SIZE_16KB [MIPS] Update/Fix instruction definitions [MIPS] DSP and MDMX share the same config flag bit. [MIPS] Fix deadlock on MP with cache aliases. [MIPS] Use generic STABS_DEBUG macro. [MIPS] Create consistency in "system type" selection. [MIPS] Use generic DWARF_DEBUG [MIPS] Fix kgdb exception handler from user mode. [MIPS] Update struct sigcontext member names [MIPS] Update/fix futex assembly [MIPS] Remove support for sysmips(2) SETNAME and MIPS_RDNVRAM operations. [MIPS] Fix detection and handling of the 74K processor. [MIPS] Add missing 34K processor IDs [MIPS] Fix marking buddy of pte global for MIPS32 w/36-bit physical address [MIPS] AU1xxx mips_timer_interrupt() fixes [MIPS] Fix typo
-
Kumba authored
Signed-off-by: Joshua Kinard <kumba@gentoo.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
This is known to be working fine for a while. While at it also update and fix the help texts. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Thiemo Seufer authored
A small bugfix for up to now unused instruction definitions, and a somewhat larger update to cover MIPS32R2 instructions. Signed-off-by: Thiemo Seufer <ths@networkno.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Thiemo Seufer authored
Clarify comment. Signed-off-by: Thiemo Seufer <ths@networkno.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
A proper fix would involve introducing the notion of shared caches but at this stage of 2.6.17 that's going to be too intrusive and not needed for current hardware; aside I think some discussion will be needed. So for now on the affected SMP configurations which happen to suffer from cache aliases we make use of the fact that a single cache will be shared by all processors. This solves the deadlock issue and will improve performance by getting rid of the smp_call_function overhead. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Atsushi Nemoto authored
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Martin Michlmayr authored
The "system type" Kconfig options on MIPS are not consistent. For some platforms, only the name is listed while other entries are prepended with "Support for". Remove this as it doesn't make sense when describing the "system type". Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Atsushi Nemoto authored
When debugging a kernel compiled by gcc 4.1 with gdb 6.4, gdb could not show filename, linenumber, etc. It seems fixed if I used generic DWARF_DEBUG macro. Although gcc 3.x seems work without this change, it would be better to use the generic macro unless there were something MIPS specific. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Atsushi Nemoto authored
Fix a calculation of saved vector address in trap_low. (damage done by lmo f4c72cc7) Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Daniel Jacobowitz authored
Rename the 64-bit sc_hi and sc_lo arrays to use the same names as the 32-bit struct sigcontext (sc_mdhi, sc_hi1, et cetera). Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
o Implement futex_atomic_op_inuser() operation o Don't use the R10000-ll/sc bug workaround version for every processor. branch likely is deprecated and some historic ll/sc processors don't implement it. In any case it's slow. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
SETNAME only had a minor defect but probably never had a user and MIPS_RDNVRAM was unimplemented anyway. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Chris Dearman authored
Nothing exciting; Linux just didn't know it yet so this is most adding a value to a case statement. Signed-off-by: Chris Dearman <chris@mips.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Nigel Stephens authored
The 34K is very much like a 24K on steroids. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Sergei Shtylyov authored
In case of CONFIG_64BIT_PHYS_ADDR, set_pte() and pte_clear() functions only set _PAGE_GLOBAL bit in the pte_low field of the buddy PTEs, forgetting to propagate ito to pte_high. Thus, the both pages might not really be made global for the CPU (since it AND's the G-bit of the odd / even PTEs together to decide whether they're global or not). Thus, if only a single page is allocated via vmalloc() or ioremap(), it's not really global for CPU (and it must be, since this is kernel mapping), and thus its ASID is compared against the current process' one -- so, we'll get into trouble sooner or later... Also, pte_none() will fail on global pages because _PAGE_GLOBAL bit is set in both pte_low and pte_high, and pte_val() will return u64 value consisting of those fields concateneted. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Herbert Valerio Riedel authored
common/au1000/irq.c was missing a mips_timer_interrupt() prototype, whereas in common/au1000/time.c the actual mips_timer_interrupt() implementation was missing an irq_exit() invocation, causing a preempt_count() leak. Signed-off-by: Herbert Valerio Riedel <hvr@hvrlab.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
Found by Chris Dearman (chris@mips.com). Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Deepak Saxena authored
The ARM Architecture Reference Manual lists bit 4 of the PMD as "implementation defined" and it must be set to zero on Intel XScale CPUs or the cache does not behave properly. Found by Mike Rapoport while debugging a flash issue on the PXA255: http://marc.10east.com/?l=linux-arm-kernel&m=114845287600782&w=1Signed-off-by: Deepak Saxena <dsaxena@plexity.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Andrew Morton authored
From: Andrew Morton <akpm@osdl.org> Move the forward decl outside the ifdef, since we use it in both legs. Should fix the spacr64 build error reported in http://bugzilla.kernel.org/show_bug.cgi?id=6625Acked-by: "David S. Miller" <davem@davemloft.net> Cc: Cedric Pellerin <cedric@bidouillesoft.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
NeilBrown authored
From: NeilBrown <neilb@suse.de> If an error is reported by a drive in a RAID array (which is done via bi_end_io - in interrupt context), we call md_error and md_new_event which calls sysfs_notify. However sysfs_notify grabs a mutex and so cannot be called in interrupt context. This patch just creates a variant of md_new_event which avoids the sysfs call, and uses that. A better fix for later is to arrange for the event to be called from user-context. Note: avoiding the sysfs call isn't a problem as an error will not, by itself, modify the sync_action attribute. (We do still need to wake_up(&md_event_waiters) as an error by itself will modify /proc/mdstat). Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Jeremy Higdon authored
From: Jeremy Higdon <jeremy@sgi.com> This patch fixes a bug in sgiioc4 where it was using the default IDE port I/O operations instead of MMIO. The IDE part of the IOC4 chip uses MMIO to map the chip registers. Unfortunately, the sgiioc4 driver uses the default port IO operations, which happens to have worked for the past few years. That's about to change, however, thus this change from inX/outX to readX/writeX. Signed-off-by: Jeremy Higdon <jeremy@sgi.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Martin Michlmayr authored
From: Martin Michlmayr <tbm@cyrius.com> Fix the following compilation error: CC drivers/video/maxinefb.o drivers/video/maxinefb.c:58: warning: initializer-string for array of chars is too long drivers/video/maxinefb.c:58: warning: (near initialization for \u2018maxinefb_fix.id\u2019) drivers/video/maxinefb.c:110: error: unknown field \u2018fb_get_fix\u2019 specified in initializer drivers/video/maxinefb.c:110: error: \u2018gen_get_fix\u2019 undeclared here (not in a function) drivers/video/maxinefb.c:111: error: unknown field \u2018fb_get_var\u2019 specified in initializer drivers/video/maxinefb.c:111: error: \u2018gen_get_var\u2019 undeclared here (not in a function) make[2]: *** [drivers/video/maxinefb.o] Error 1 Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Antonino Daplas <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Rodolfo Giometti authored
From: Rodolfo Giometti <giometti@linux.it> Fix the following warning on compilation: drivers/video/au1100fb.c: In function `au1100fb_fb_setcolreg': drivers/video/au1100fb.c:219: warning: ISO C90 forbids mixed declarations and code drivers/video/au1100fb.c: In function `au1100fb_fb_pan_display': drivers/video/au1100fb.c:321: warning: ISO C90 forbids mixed declarations and code drivers/video/au1100fb.c: In function `au1100fb_fb_mmap': drivers/video/au1100fb.c:387: warning: ISO C90 forbids mixed declarations and code drivers/video/au1100fb.c: In function `au1100fb_drv_probe': drivers/video/au1100fb.c:471: warning: unsigned int format, long unsigned int arg (arg 2) drivers/video/au1100fb.c: At top level: drivers/video/au1100fb.c:617: warning: initialization from incompatible pointer type drivers/video/au1100fb.c:618: warning: initialization from incompatible pointer type Signed-off-by: Rodolfo Giometti <giometti@linux.it> Signed-off-by: Antonino Daplas <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Benjamin Herrenschmidt authored
From: Benjamin Herrenschmidt <benh@kernel.crashing.org> Prevent calling of some platform functions on the clock chips of the eMac as it seems to cause it to lockup at boot. For now, add a quirk to prevent that from happening. Later, I might find out what's wrong and fix it but that doesn't seem to be important as the machine appear to work fine without running those. It's possible that Darwin doesn't run them. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Nathan Pilatzke <nathanpilatzke@gmail.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Stephen Hemminger authored
From: Stephen Hemminger <shemminger@osdl.org> I want to use the hrtimer's in the netem (Network Emulator) qdisc. But the necessary symbols aren't exported for module use. Also needed by SystemTap. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "Stone, Joshua I" <joshua.i.stone@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Andrew Morton authored
From: Andrew Morton <akpm@osdl.org> Revert commit ff4da2e2. It broke APM suspend, probably because APM doesn't switch back to a VT when suspending. Tracked down by Matt Mackall <mpm@selenic.com> Rafael sayeth: "It only fixed the theoretical issue that a quick-handed user could switch to X after processes have been frozen and before the devices are suspended. With the current userland suspend tools it shouldn't be necessary." Cc: Pavel Machek <pavel@ucw.cz> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Corey Minyard authored
From: Corey Minyard <minyard@acm.org> This patch is pretty important to get in for IPMI, new systems have been changing the way ACPI and IPMI interact, and this works around the problems for now. This is a temporary fix until we get proper ACPI handling in IPMI. Fixed releasing already-allocated regions when a later request fails, and forward-ported it to HEAD. Some BIOSes reserve disjoint I/O regions in their ACPI tables for the IPMI controller. This causes problems when trying to register the entire I/O region. Therefore we must register each I/O port separately. Signed-off-by: Jordan Hargrave <Jordan_Hargrave@dell.com> Signed-off-by: Matt Domsch <Matt_Domsch@dell.com> Signed-off-by: Corey Minyard <minyard@acm.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Seiji Munetoh authored
From: Seiji Munetoh <seiji.munetoh@gmail.com> Change the binary output format to actual ACPI TCPA log structure since the current format does not contain all event-data information that need to verify the PCRs in TPM. tpm_binary_bios_measurements_show() uses get_event_name() to convert the binary event-data to ascii format, and puts them as binary. However, to verify the PCRs, the event-data must be a actual binary event-data used by SHA1 calc. in BIOS. So, I think actual ACPI TCPA log is good for this binary output format. That way, any userland tools easily parse this data with reference to TCG PC specification. Signed-off-by: Seiji Munetoh <seiji.munetoh@gmail.com> Acked-by: Kylene Hall <kjhall@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Seiji Munetoh authored
From: Seiji Munetoh <seiji.munetoh@gmail.com> Fix "tcpa_pc_event" misalignment between enum, strings and TCG PC spec and output of the event which contains a hash data. Signed-off-by: Seiji Munetoh <seiji.munetoh@gmail.com> Acked-by: Kylene Hall <kjhall@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Yasunori Goto authored
From: Yasunori Goto <y-goto@jp.fujitsu.com> If hot-added memory's address is smaller than old area, spanned_pages will not be updated. It must be fixed. example) Old zone_start_pfn = 0x60000, and spanned_pages = 0x10000 Added new memory's start_pfn = 0x50000, and end_pfn = 0x60000 new spanned_pages will be still 0x10000 by old code. (It should be updated to 0x20000.) Because old_zone_end_pfn will be 0x70000, and end_pfn smaller than it. So, spanned_pages will not be updated. In current code, spanned_pages is updated only when end_pfn is updated. But, it should be updated by subtraction between bigger end_pfn and new zone_start_pfn. Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
David Hollister authored
From: David Hollister <david.hollister@amd.com> After the system boots with the logo, if the first action is a scrollback, the screen may become garbled. This patch ensures that the softback_curr value is updated along with softback_in following the scrollback. Signed-off-by: David Hollister <david.hollister@amd.com> Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Cc: "Antonino A. Daplas" <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-