Current touchpanel had below 2 issues

- LCDD2 pin which is needed for WVGA was changed to
  IRQ28_123 pin on ts_get_pendown_state

- GPIO pull up on ts_init was disabled by gpio_request
  on ts_get_pendown_state.
  This mean the return value from gpio_get_value is untrusted.

This patch solve these issues
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add video modes for 480p and SXGA (1280x1024).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

With this patch hot-plugging of an HDMI or a DVI monitor can select a different
video mode and reconfigure the LCDC and HDMI controllers accordingly. Due to a
lack of a standard API to inform framebuffer users of a changed video mode, the
framebuffer configuration is preserved regardless of a specific mode, selected
for the monitor. As described in a previous patch, this leads to smaller
framebuffers being displayed on larger monitors or a part of a larger
framebuffer being displayed on a smaller resolution monitor.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

High monitor resolutions also require higher clock frequencies, current HDMI
PHY parameters do not work well for resolutions higher than 720p.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Improve comments, unify function names, replace pr_debug with dev_dbg.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This is a preparation for a patch, that shall allow displaying of a smaller
framebuffer on a bigger display and of a part of a bigger framebuffer on a
smaller display.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The SH-Mobile HDMI driver runs in several contexts: ISR, delayed work-queue,
task context, when called from the sh_mobile_lcdc framebuffer driver. This
creates ample race possibilities. Even though most these races are purely
theoretical, it is better to close them. To trace fb_info validity we install a
notification callback in the HDMI driver, and the only way for it to get to
driver internal data is by using struct sh_mobile_lcdc_chan, therefore it had
to be extracted into a separate common header.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The SH-Mobile HDMI controller supports two configuration modes: using
pre-programmed VICs and the "external" mode - specifying video parameters
explicitly. The driver already contains code, necessary to configure HDMI
manually, this patch actually enables it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

To support standard video modes, other than 720p, the HDMI PHY configuration
has to be adjusted and the VIC has to be sent to the display.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Now, that we add support for multiple modes to the sh_mobile_lcdcfb driver, it
has to allocate memory, sufficient for the biggest of them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Notifier callbacks have to return either one of NOTIFY_* codes or a negative
errno, converted to a suitable value by the notifier_from_errno() inline, if
the notifier chain shall not be continued.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This is a preparation for HDMI hotplug support. This patch just moves all
platform defined video modes for the sh_mobile_lcdcfb driver to separate
arrays and switches all users to use element 0 of that array, so, this patch
doesn't introduce any functional changes and as such should not cause any
regressions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Remove an unused variable and simplify several pointer dereferences.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch fixes the following two erroneous error paths:

hw_usecnt is allocated with a value of 0, therefore in an early error case,
calling sh_mobile_lcdc_clk_off() will wrongly conclude, that hw_usecnt has
already been incremented. Then sh_mobile_lcdc_runtime_suspend() will be called,
which will access uninitialised data fields and crash the kernel.

sh_mobile_lcdc_stop() can be called before framebuffer has been allocated, then
ch->info is NULL and dereferencing it will Oops too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The present SH-Mobile HDMI driver reads and parses the EDID block into a
variable screeninfo object, but since it is still unable to dynamically
reconfigure the framebuffer, it overwrites the EDID information with preset
values again. This patch just uses a temporary variable to store the EDID
timing information instead.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Use the standard fb_videomode_to_var() instead of filling fb_var_screeninfo
fields manually in, also remove a redundant memset(0).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add ignored device name by comment-out in INTCS.
And MSIOF which has been forgotten is added
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Use evt2irq() for DMAC resources on sh7372.

This makes the code easier to read and also
allows adjusting the INTC base offset without
breaking platform data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Extend dip switch comments for QHD and WVGA LCD panels
on AP4EVB. Similar to the Ecovec comments.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Current gamut, acp, isrc1, isrc2 settings are wrong,
and not necessary for now.
Tested-by: Takanari Hayama <taki@igel.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch modify x_plate_ohms to correct value for tsc2007,
and removed un-necessary ts_get_pendown_state().
gpio_pull_up() was removed also.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

* 'sched/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Improve latencies under load by decreasing minimum scheduling granularity

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k,m68knommu: Wire up fanotify_init, fanotify_mark, and prlimit64

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] fix siglock

Quoth Tony:

 "I committed the fix for this last week prior to your -rc4 announcement
  reminding us to give proper "Reported-by:" credit.  This one should have
  had:
Reported-by: Tony Ernst <tee@sgi.com>

  and also
Much-useful-investigation-and-tracing-by: Hedi Berriche <hedi@sgi.com>
  Much-useful-investigation-and-tracing-by: Petr Tesarik <ptesarik@novell.com>"

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: prevent possible memory corruption in cifs_demultiplex_thread
  cifs: eliminate some more premature cifsd exits
  cifs: prevent cifsd from exiting prematurely
  [CIFS] ntlmv2/ntlmssp remove-unused-function CalcNTLMv2_partial_mac_key
  cifs: eliminate redundant xdev check in cifs_rename
  Revert "[CIFS] Fix ntlmv2 auth with ntlmssp"
  Revert "missing changes during ntlmv2/ntlmssp auth and sign"
  Revert "Eliminate sparse warning - bad constant expression"
  Revert "[CIFS] Eliminate unused variable warning"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  fs/9p: Don't use dotl version of mknod for dotu inode operations
  fs/9p: Use the correct dentry operations
  9p: Check for NULL fid in v9fs_dir_release()
  fs/9p: Fix error handling in v9fs_get_sb
  fs/9p, net/9p: memory leak fixes

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
  dquot: do full inode dirty in allocating space

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
  spi/pl022: move probe call to subsys_initcall()
  powerpc/5200: mpc52xx_uart.c: Add of_node_put to avoid memory leak
  spi/pl022: fix APB pclk power regression on U300
  spi/spi_s3c64xx: Warn if PIO transfers time out
  spi/s3c64xx: Fix incorrect reuse of 'val' local variable.
  spi/s3c64xx: Fix compilation warning
  spi/dw_spi: clean the cs_control code
  spi/dw_spi: Allow interrupt sharing
  spi/spi_s3c64xx: Increase dead reckoning time in wait_for_xfer()
  spi/spi_s3c64xx: Move to subsys_initcall()
  spi: free children in spi_unregister_master, not siblings
  gpiolib: Add 'struct gpio_chip' forward declaration for !GPIOLIB case
  of: Fix missing includes - ll_temac
  spi/spi_s3c64xx: Staticise non-exported functions
  spi/spi_s3c64xx: Make probe more robust against missing board config

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>

Mathieu reported bad latencies with make -j10 kind of kbuild
workloads - which is mostly caused by us scheduling with a
too coarse granularity.

Reduce the minimum granularity some more, to make sure we
can meet the latency target.

I got the following results (make -j10 kbuild load, average of 3
runs):

 vanilla:

  maximum latency: 38278.9 µs
  average latency:  7730.1 µs

 patched:

  maximum latency: 22702.1 µs
  average latency:  6684.8 µs

Mathieu also measured it:

|
| * wakeup-latency.c (SIGEV_THREAD) with make -j10
|
| - Mainline 2.6.35.2 kernel
|
| maximum latency: 45762.1 µs
| average latency: 7348.6 µs
|
| - With only Peter's smaller min_gran (shown below):
|
| maximum latency: 29100.6 µs
| average latency: 6684.1 µs
|
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Suggested-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <AANLkTi=8m4g01wZPacySoF7U0PevTNVgJoZZrHiUD-pN@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

We should not use dotlversion for the dotu inode operations
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>

We should use the cached dentry operation only if caching mode is enabled
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>

NULL fid should be handled in cases where we endup calling v9fs_dir_release()
before even we instantiate the fid in filp.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>

This was introduced by 7cadb63d58a932041afa3f957d5cbb6ce69dcee5
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>

Four memory leak fixes in the 9P code.
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>

Fix docbook templates that reference files that do not contain the
expected kernel-doc notation.

Fixes these warnings:

  Warning(arch/x86/include/asm/unaligned.h): no structured comments found
  Warning(lib/vsprintf.c): no structured comments found

These cause errors in the generated html output, like below, so drop
these lines.

  Name
  arch/x86/include/asm/unaligned.h - Document generation inconsistency
  Oops
  Warning
  The template for this document tried to insert the structured comment from the file arch/x86/include/asm/unaligned.h at this point, but none was found. This dummy section is inserted to allow generation to continue.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When you don't use !E or !I but only !F, then it's very easy to miss
including some functions, structs etc.  in documentation.  To help
finding which ones were missed, allow printing out the unused ones as
warnings.

For example, using this on mac80211 yields a lot of warnings like this:

  Warning: didn't use docs for DOC: mac80211 workqueue
  Warning: didn't use docs for ieee80211_max_queues
  Warning: didn't use docs for ieee80211_bss_change
  Warning: didn't use docs for ieee80211_bss_conf

when generating the documentation for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There are valid attributes that could have upper case letters, but we
still want to remove, like for example
	__attribute__((aligned(NETDEV_ALIGN)))
as encountered in the wireless code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>