The IP_ADVANCED_ROUTER Kconfig describes the rp_filter
proc option.  Recent changes added a loose mode.
Instead of documenting this change too places, refer to
the document describing it:
 Documentation/networking/ip-sysctl.txt

I'm considering moving the rp_filter description away
from the Kconfig file into ip-sysctl.txt.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix up whitespaces while going though ip-sysctl.txt anyway.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

First fix a typo in Stephens patch ;-)
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

PCI bar 0 is used for memory mapped register access.
If ioremap fails (returns NULL), register access results
in crash.

Use pci_ioremap_bar() instead of ioremap(), the latter
fails on on 32 bit powerpc where pci resource address is
> 32 bits.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PCI function to physical port mapping is valid only for
old firmware. New firmware (4.0.0+) abstracts this.
So driver should never try to access phy using invalid
mapping. The behavior is unpredictable when PCI functions
4-7 are enabled on the same NIC.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net: amend the fix for SO_BSDCOMPAT gsopt infoleak
  netns: build fix for net_alloc_generic

de_get is called before every proc_get_inode, but corresponding de_put is
called only when dropping last reference to an inode. This might cause
something like
remove_proc_entry: /proc/stats busy, count=14496
to be printed to the syslog.

The fix is to call de_put in case of an already initialized inode in
proc_get_inode.
Signed-off-by: Krzysztof Sachanowicz <analyzer1@gmail.com>
Tested-by: Marcin Pilipczuk <marcin.pilipczuk@gmail.com>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In the KMS case, enter/leavevt won't fix up the interrupt handler for
us, so we need to do it at suspend/resume time.  Make sure we don't fail
the resume if the chip is hung either.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

dev_priv->hw_status_page can be NULL, if i915_gem_retire_requests()
is called from i915_gem_busy_ioctl().

Signed-off-by Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The fix for CVE-2009-0676 (upstream commit df0bca04) is incomplete. Note
that the same problem of leaking kernel memory will reappear if someone
on some architecture uses struct timeval with some internal padding (for
example tv_sec 64-bit and tv_usec 32-bit) --- then, you are going to
leak the padded bytes to userspace.
Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_alloc_generic was defined in #ifdef CONFIG_NET_NS, but used
unconditionally. Move net_alloc_generic out of #ifdef.
Signed-off-by: Clemens Noss <cnoss@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: ahash - Fix digest size in /proc/crypto

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  netns: fix double free at netns creation
  veth : add the set_mac_address capability
  sunlance: Beyond ARRAY_SIZE of ib->btx_ring
  sungem: another error printed one too early
  ISDN: fix sc/shmem printk format warning
  SMSC: timeout reaches -1
  smsc9420: handle magic field of ethtool_eeprom
  sundance: missing parentheses?
  smsc9420: fix another postfixed timeout
  wimax/i2400m: driver loads firmware v1.4 instead of v1.3
  vlan: Update skb->mac_header in __vlan_put_tag().
  cxgb3: Add support for PCI ID 0x35.
  tcp: remove obsoleted comment about different passes
  TG3: &&/|| confusion
  ATM: misplaced parentheses?
  net/mv643xx: don't disable the mib timer too early and lock properly
  net/mv643xx: use GFP_ATOMIC while atomic
  atl1c: Atheros L1C Gigabit Ethernet driver
  net: Kill skb_truesize_check(), it only catches false-positives.
  net: forcedeth: Fix wake-on-lan regression

Add missing parameter value to list of available values
for acpi=<value>.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It turns out that net_alive is unnecessary, and the original problem
that led to it being added was simply that the icmp code thought
it was a network device and wound up being unable to handle packets
while there were still packets in the network namespace.

Now that icmp and tcp have been fixed to properly register themselves
this problem is no longer present and we have a stronger guarantee
that packets will not arrive in a network namespace then that provided
by net_alive in netif_receive_skb.  So remove net_alive allowing
packet reception run a little faster.

Additionally document the strong reason why network namespace cleanup
is safe so that if something happens again someone else will have
a chance of figuring it out.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To remove the possibility of packets flying around when network
devices are being cleaned up use reisger_pernet_subsys instead of
register_pernet_device.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recently I had a kernel panic in icmp_send during a network namespace
cleanup.  There were packets in the arp queue that failed to be sent
and we attempted to generate an ICMP host unreachable message, but
failed because icmp_sk_exit had already been called.

The network devices are removed from a network namespace and their
arp queues are flushed before we do attempt to shutdown subsystems
so this error should have been impossible.

It turns out icmp_init is using register_pernet_device instead
of register_pernet_subsys.  Which resulted in icmp being shut down
while we still had the possibility of packets in flight, making
a nasty NULL pointer deference in interrupt context possible.

Changing this to register_pernet_subsys fixes the problem in
my testing.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

While going through net/ipv4/Kconfig cleanup whitespaces.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The reverse path filter (rp_filter) will NOT get enabled
when enabling forwarding.  Read the code and tested in
in practice.

Most distributions do enable it in startup scripts.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

If this module can't load, it is almost certainly because something else
is already bound to that SAP. So in that case, return the same error code
as other SAP usage, and fail the module load.

Also fixes a compiler warning about printk of non const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mark some strings as const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Get rid of compile warning about non-const format
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend existing reverse path filter option to allow strict or loose
filtering. (See http://en.wikipedia.org/wiki/Reverse_path_filtering).

For compatibility with existing usage, the value 1 is chosen for strict mode
and 2 for loose mode.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 7d3d5ec1.

Russell is going to merge this in via the ARM tree.
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/i915: Add missing mutex_lock(&dev->struct_mutex)
  drm/i915: fix WC mapping in non-GEM i915 code.
  drm/i915: Fix regression in 95ca9d
  drm/i915: Retire requests from i915_gem_busy_ioctl.
  drm/i915: suspend/resume GEM when KMS is active
  drm/i915: Don't let a device flush to prepare buffers clear new write_domains.
  drm/i915: Cut two args to set_to_gpu_domain that confused this tricky path.

there might be a nicer way to fix this but this is the simplest for now.
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>

[airlied - taken from mailing list posting]
Signed-off-by: Dave Airlie <airlied@redhat.com>

The object is dereferenced before the NULL check. Oops.

Fixes http://bugs.freedesktop.org/show_bug.cgi?id=20235Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This ensures that the user gets the latest information from the hardware
on whether the buffer is busy, potentially reducing the working set of objects
that the user chooses.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

In the KMS case, we need to suspend/resume GEM as well.  So on suspend, make
sure we idle GEM and stop any new rendering from coming in, and on resume,
re-init the framebuffer and clear the suspended flag.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The problem was that object_set_to_gpu_domain would set the new write_domains
that are getting set by this batchbuffer, then the accumulated flushes required
for all the objects in preparation for this batchbuffer were posted, and the
brand new write domain would get cleared by the flush being posted.  Instead,
hang on to the new (or old if we're not changing it) value and set it after
the flush is queued.

Results from this noticably included conformance test failures from reads
shortly after writes (where the new write domain had been lost and thus not
flushed and waited on), but is a suspected cause of hangs in some apps when
a write domain is lost on a buffer that gets reused for instruction or
commmand state.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

While not strictly required, it helped while thinking about the following
change.  This change should be invariant.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

At some point we (okay, I) managed to break the ability for users to use the
setsockopt() syscall to set IPv4 options when NetLabel was not active on the
socket in question.  The problem was noticed by someone trying to use the
"-R" (record route) option of ping:

 # ping -R 10.0.0.1
 ping: record route: No message of desired type

The solution is relatively simple, we catch the unlabeled socket case and
clear the error code, allowing the operation to succeed.  Please note that we
still deny users the ability to override IPv4 options on socket's which have
NetLabel labeling active; this is done to ensure the labeling remains intact.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>

The CIPSO protocol engine incorrectly stated that the FIPS-188 specification
could be found in the kernel's Documentation directory.  This patch corrects
that by removing the comment and directing users to the FIPS-188 documented
hosted online.  For the sake of completeness I've also included a link to the
CIPSO draft specification on the NetLabel website.

Thanks to Randy Dunlap for spotting the error and letting me know.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>

* 'core/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  PM: Split up sysdev_[suspend|resume] from device_power_[down|up], fix

Impact: module build fix

Fix:

 ERROR: "sysdev_resume" [arch/x86/kernel/apm.ko] undefined!
 ERROR: "sysdev_suspend" [arch/x86/kernel/apm.ko] undefined!

As these APIs are now used by the APM driver, which can be built
as a module.

Also fix a few extra (and inconsistent) newlines in comment blocks
preceding these functions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>

The kernel-api docbook was much larger than any of the others,
so processing it took longer and needed some docbook extras in
some cases, so split it into kernel-api (infrastructure etc.)
and device drivers/device subsystems.  This allows these docbooks
to be generated in parallel.  (This reduced the docbook processing
time on my 4-proc system with make -j4 from about 5min:16sec to
about 2min:01sec.)

The chapters that were moved from kernel-api to device-drivers are:

Driver Basics
Device drivers infrastructure
Parallel Port Devices
Message-based devices
Sound Devices
16x50 UART Driver
Frame Buffer Library
Input Subsystem
Serial Peripheral Interface (SPI)
I2C and SMBus Subsystem
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>