- 25 May, 2019 40 commits
-
-
Adam Ford authored
commit 7aedca87 upstream. Some USB peripherals draw more power, and the sourcing regulator take a little time to turn on. This patch fixes an issue where some devices occasionally do not get detected, because the power isn't quite ready when communication starts, so we add a bit of a delay. Fixes: 1c207f91 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM") Signed-off-by:
Adam Ford <aford173@gmail.com> Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Qu Wenruo authored
commit 10995c04 upstream. Commit d2311e69 ("btrfs: relocation: Delay reloc tree deletion after merge_reloc_roots()") expands the life span of root->reloc_root. This breaks certain checs of fs_info->reloc_ctl. Before that commit, if we have a root with valid reloc_root, then it's ensured to have fs_info->reloc_ctl. But now since reloc_root doesn't always mean a valid fs_info->reloc_ctl, such check is unreliable and can cause the following NULL pointer dereference: BUG: unable to handle kernel NULL pointer dereference at 00000000000005c1 IP: btrfs_reloc_pre_snapshot+0x20/0x50 [btrfs] PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 0 PID: 10379 Comm: snapperd Not tainted Call Trace: create_pending_snapshot+0xd7/0xfc0 [btrfs] create_pending_snapshots+0x8e/0xb0 [btrfs] btrfs_commit_transaction+0x2ac/0x8f0 [btrfs] btrfs_mksubvol+0x561/0x570 [btrfs] btrfs_ioctl_snap_create_transid+0x189/0x190 [btrfs] btrfs_ioctl_snap_create_v2+0x102/0x150 [btrfs] btrfs_ioctl+0x5c9/0x1e60 [btrfs] do_vfs_ioctl+0x90/0x5f0 SyS_ioctl+0x74/0x80 do_syscall_64+0x7b/0x150 entry_SYSCALL_64_after_hwframe+0x3d/0xa2 RIP: 0033:0x7fd7cdab8467 Fix it by explicitly checking fs_info->reloc_ctl other than using the implied root->reloc_root. Fixes: d2311e69 ("btrfs: relocation: Delay reloc tree deletion after merge_reloc_roots") Signed-off-by:
Qu Wenruo <wqu@suse.com> Reviewed-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Arnd Bergmann authored
commit f3d96467 upstream. As Stepan Golosunov points out, there is a small mistake in the get_timespec64() function in the kernel. It was originally added under the assumption that CONFIG_64BIT_TIME would get enabled on all 32-bit and 64-bit architectures, but when the conversion was done, it was only turned on for 32-bit ones. The effect is that the get_timespec64() function never clears the upper half of the tv_nsec field for 32-bit tasks in compat mode. Clearing this is required for POSIX compliant behavior of functions that pass a 'timespec' structure with a 64-bit tv_sec and a 32-bit tv_nsec, plus uninitialized padding. The easiest fix for linux-5.1 is to just make the Kconfig symbol unconditional, as it was originally intended. As a follow-up, the #ifdef CONFIG_64BIT_TIME can be removed completely.. Note: for native 32-bit mode, no change is needed, this works as designed and user space should never need to clear the upper 32 bits of the tv_nsec field, in or out of the kernel. Fixes: 00bf25d6 ("y2038: use time32 syscall names on 32-bit") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Joseph Myers <joseph@codesourcery.com> Cc: libc-alpha@sourceware.org Cc: linux-api@vger.kernel.org Cc: Deepa Dinamani <deepa.kernel@gmail.com> Cc: Lukasz Majewski <lukma@denx.de> Cc: Stepan Golosunov <stepan@golosunov.pp.ru> Link: https://lore.kernel.org/lkml/20190422090710.bmxdhhankurhafxq@sghpc.golosunov.pp.ru/ Link: https://lkml.kernel.org/r/20190429131951.471701-1-arnd@arndb.deSigned-off-by:
-
Daniel Borkmann authored
commit 50b045a8 upstream. One of the biggest issues we face right now with picking LRU map over regular hash table is that a map walk out of user space, for example, to just dump the existing entries or to remove certain ones, will completely mess up LRU eviction heuristics and wrong entries such as just created ones will get evicted instead. The reason for this is that we mark an entry as "in use" via bpf_lru_node_set_ref() from system call lookup side as well. Thus upon walk, all entries are being marked, so information of actual least recently used ones are "lost". In case of Cilium where it can be used (besides others) as a BPF based connection tracker, this current behavior causes disruption upon control plane changes that need to walk the map from user space to evict certain entries. Discussion result from bpfconf [0] was that we should simply just remove marking from system call side as no good use case could be found where it's actually needed there. Therefore this patch removes marking for regular LRU and per-CPU flavor. If there ever should be a need in future, the behavior could be selected via map creation flag, but due to mentioned reason we avoid this here. [0] http://vger.kernel.org/bpfconf.html Fixes: 29ba732a ("bpf: Add BPF_MAP_TYPE_LRU_HASH") Fixes: 8f844938 ("bpf: Add BPF_MAP_TYPE_LRU_PERCPU_HASH") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Martin KaFai Lau <kafai@fb.com> Signed-off-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Daniel Borkmann authored
commit c6110222 upstream. Add a callback map_lookup_elem_sys_only() that map implementations could use over map_lookup_elem() from system call side in case the map implementation needs to handle the latter differently than from the BPF data path. If map_lookup_elem_sys_only() is set, this will be preferred pick for map lookups out of user space. This hook is used in a follow-up fix for LRU map, but once development window opens, we can convert other map types from map_lookup_elem() (here, the one called upon BPF_MAP_LOOKUP_ELEM cmd is meant) over to use the callback to simplify and clean up the latter. Signed-off-by:
-
Chenbo Feng authored
commit e547ff3f upstream. For iptable module to load a bpf program from a pinned location, it only retrieve a loaded program and cannot change the program content so requiring a write permission for it might not be necessary. Also when adding or removing an unrelated iptable rule, it might need to flush and reload the xt_bpf related rules as well and triggers the inode permission check. It might be better to remove the write premission check for the inode so we won't need to grant write access to all the processes that flush and restore iptables rules. Signed-off-by:
Chenbo Feng <fengc@google.com> Signed-off-by:
-
John Garry authored
commit 0b777eee upstream. In commit 376991db ("driver core: Postpone DMA tear-down until after devres release"), we changed the ordering of tearing down the device DMA ops and releasing all the device's resources; this was because the DMA ops should be maintained until we release the device's managed DMA memories. However, we have seen another crash on an arm64 system when a device driver probe fails: hisi_sas_v3_hw 0000:74:02.0: Adding to iommu group 2 scsi host1: hisi_sas_v3_hw BUG: Bad page state in process swapper/0 pfn:313f5 page:ffff7e0000c4fd40 count:1 mapcount:0 mapping:0000000000000000 index:0x0 flags: 0xfffe00000001000(reserved) raw: 0fffe00000001000 ffff7e0000c4fd48 ffff7e0000c4fd48 0000000000000000 raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000 page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set bad because of flags: 0x1000(reserved) Modules linked in: CPU: 49 PID: 1 Comm: swapper/0 Not tainted 5.1.0-rc1-43081-g22d97fd-dirty #1433 Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - V1.12.01 01/29/2019 Call trace: dump_backtrace+0x0/0x118 show_stack+0x14/0x1c dump_stack+0xa4/0xc8 bad_page+0xe4/0x13c free_pages_check_bad+0x4c/0xc0 __free_pages_ok+0x30c/0x340 __free_pages+0x30/0x44 __dma_direct_free_pages+0x30/0x38 dma_direct_free+0x24/0x38 dma_free_attrs+0x9c/0xd8 dmam_release+0x20/0x28 release_nodes+0x17c/0x220 devres_release_all+0x34/0x54 really_probe+0xc4/0x2c8 driver_probe_device+0x58/0xfc device_driver_attach+0x68/0x70 __driver_attach+0x94/0xdc bus_for_each_dev+0x5c/0xb4 driver_attach+0x20/0x28 bus_add_driver+0x14c/0x200 driver_register+0x6c/0x124 __pci_register_driver+0x48/0x50 sas_v3_pci_driver_init+0x20/0x28 do_one_initcall+0x40/0x25c kernel_init_freeable+0x2b8/0x3c0 kernel_init+0x10/0x100 ret_from_fork+0x10/0x18 Disabling lock debugging due to kernel taint BUG: Bad page state in process swapper/0 pfn:313f6 page:ffff7e0000c4fd80 count:1 mapcount:0 mapping:0000000000000000 index:0x0 [ 89.322983] flags: 0xfffe00000001000(reserved) raw: 0fffe00000001000 ffff7e0000c4fd88 ffff7e0000c4fd88 0000000000000000 raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000 The crash occurs for the same reason. In this case, on the really_probe() failure path, we are still clearing the DMA ops prior to releasing the device's managed memories. This patch fixes this issue by reordering the DMA ops teardown and the call to devres_release_all() on the failure path. Reported-by:
Xiang Chen <chenxiang66@hisilicon.com> Tested-by:
John Garry <john.garry@huawei.com> Reviewed-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
-
Angus Ainslie (Purism) authored
commit 941acd56 upstream. On imx8mq B0 chip, AHB/SDMA clock ratio 2:1 can't be supported, since SDMA clock ratio has to be increased to 250Mhz, AHB can't reach to 500Mhz, so use 1:1 instead. To limit this change to the imx8mq for now this patch also adds an im8mq-sdma compatible string. Signed-off-by:
Angus Ainslie (Purism) <angus@akkea.ca> Acked-by:
Robin Gong <yibin.gong@nxp.com> Signed-off-by:
Vinod Koul <vkoul@kernel.org> Cc: Richard Leitner <richard.leitner@skidata.com> Signed-off-by:
-
Nigel Croxon authored
commit b2176a1d upstream. The problem is that any 'uptodate' vs 'disks' check is not precise in this path. Put a "WARN_ON(!test_bit(R5_UPTODATE, &dev->flags)" on the device that might try to kick off writes and then skip the action. Better to prevent the raid driver from taking unexpected action *and* keep the system alive vs killing the machine with BUG_ON. Note: fixed warning reported by kbuild test robot <lkp@intel.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Nigel Croxon <ncroxon@redhat.com> Signed-off-by:
Song Liu <songliubraving@fb.com> Signed-off-by:
-
Song Liu authored
commit a25d8c32 upstream. This reverts commit 4f4fd7c5. Cc: Dan Williams <dan.j.williams@intel.com> Cc: Nigel Croxon <ncroxon@redhat.com> Cc: Xiao Ni <xni@redhat.com> Signed-off-by:
-
Michael Lass authored
commit 51b86f9a upstream. Commit 61697a6a ("dm: eliminate 'split_discard_bios' flag from DM target interface") incorrectly removed code from __send_changing_extent_only() that is required to impose a per-target IO boundary on IO that exceeds max_io_len_target_boundary(). Otherwise "special" IO (e.g. DISCARD, WRITE SAME, WRITE ZEROES) can write beyond where allowed. Fix this by restoring the max_io_len_target_boundary() limit in __send_changing_extent_only() Fixes: 61697a6a ("dm: eliminate 'split_discard_bios' flag from DM target interface") Cc: stable@vger.kernel.org # 5.1+ Signed-off-by:
Michael Lass <bevan@bi-co.net> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Kirill Smelkov authoredcommit bbd84f33 upstream. Starting from commit 9c225f26 ("vfs: atomic f_pos accesses as per POSIX") files opened even via nonseekable_open gate read and write via lock and do not allow them to be run simultaneously. This can create read vs write deadlock if a filesystem is trying to implement a socket-like file which is intended to be simultaneously used for both read and write from filesystem client. See commit 10dce8af ("fs: stream_open - opener for stream-like files so that read and write can run simultaneously without deadlock") for details and e.g. commit 581d21a2 ("xenbus: fix deadlock on writes to /proc/xen/xenbus") for a similar deadlock example on /proc/xen/xenbus. To avoid such deadlock it was tempting to adjust fuse_finish_open to use stream_open instead of nonseekable_open on just FOPEN_NONSEEKABLE flags, but grepping through Debian codesearch shows users of FOPEN_NONSEEKABLE, and in particular GVFS which actually uses offset in its read and write handlers https://codesearch.debian.net/search?q=-%3Enonseekable+%3D https://gitlab.gnome.org/GNOME/gvfs/blob/1.40.0-6-gcbc54396/client/gvfsfusedaemon.c#L1080 https://gitlab.gnome.org/GNOME/gvfs/blob/1.40.0-6-gcbc54396/client/gvfsfusedaemon.c#L1247-1346 https://gitlab.gnome.org/GNOME/gvfs/blob/1.40.0-6-gcbc54396/client/gvfsfusedaemon.c#L1399-1481 so if we would do such a change it will break a real user. Add another flag (FOPEN_STREAM) for filesystem servers to indicate that the opened handler is having stream-like semantics; does not use file position and thus the kernel is free to issue simultaneous read and write request on opened file handle. This patch together with stream_open() should be added to stable kernels starting from v3.14+. This will allow to patch OSSPD and other FUSE filesystems that provide stream-like files to return FOPEN_STREAM | FOPEN_NONSEEKABLE in open handler and this way avoid the deadlock on all kernel versions. This should work because fuse_finish_open ignores unknown open flags returned from a filesystem and so passing FOPEN_STREAM to a kernel that is not aware of this flag cannot hurt. In turn the kernel that is not aware of FOPEN_STREAM will be < v3.14 where just FOPEN_NONSEEKABLE is sufficient to implement streams without read vs write deadlock. Cc: stable@vger.kernel.org # v3.14+ Signed-off-by:
Kirill Smelkov <kirr@nexedi.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Martin Wilck authored
commit 940bc471 upstream. Commit b592211c ("dm mpath: fix attached_handler_name leak and dangling hw_handler_name pointer") fixed a memory leak for the case where setup_scsi_dh() returns failure. But setup_scsi_dh may return success and not "use" attached_handler_name if the retain_attached_hwhandler flag is not set on the map. As setup_scsi_sh properly "steals" the pointer by nullifying it, freeing it unconditionally in parse_path() is safe. Fixes: b592211c ("dm mpath: fix attached_handler_name leak and dangling hw_handler_name pointer") Cc: stable@vger.kernel.org Reported-by:
Yufen Yu <yuyufen@huawei.com> Signed-off-by:
Martin Wilck <mwilck@suse.com> Signed-off-by:
-
Helen Koike authored
commit 0f41fcf7 upstream. The dm_early_create() function (which deals with "dm-mod.create=" kernel command line option) calls dm_hash_insert() who gets an extra reference to the md object. In case of failure, this reference wasn't being released, causing dm_destroy() to hang, thus hanging the whole boot process. Fix this by calling __hash_remove() in the error path. Fixes: 6bbc923d ("dm: add support to directly boot to a mapped device") Cc: stable@vger.kernel.org Signed-off-by:
Helen Koike <helen.koike@collabora.com> Signed-off-by:
-
Mikulas Patocka authored
commit 30bba430 upstream. When we use separate devices for data and metadata, dm-integrity would incorrectly calculate the size of the metadata device as if it had 512-byte block size - and it would refuse activation with larger block size and smaller metadata device. Fix this so that it takes actual block size into account, which fixes the following reported issue: https://gitlab.com/cryptsetup/cryptsetup/issues/450 Fixes: 356d9d52 ("dm integrity: allow separate metadata device") Cc: stable@vger.kernel.org # v4.19+ Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Milan Broz authored
commit 7a1cd723 upstream. The information about tag size should not be printed without debug info set. Also print device major:minor in the error message to identify the device instance. Also use rate limiting and debug level for info about used crypto API implementaton. This is important because during online reencryption the existing message saturates syslog (because we are moving hotzone across the whole device). Cc: stable@vger.kernel.org Signed-off-by:
Milan Broz <gmazyland@gmail.com> Signed-off-by:
-
Mikulas Patocka authored
commit 81bc6d15 upstream. When the target line contains an invalid device, delay_ctr() will call delay_dtr() with NULL workqueue. Attempting to destroy the NULL workqueue causes a crash. Signed-off-by:
-
Helen Koike authored
commit 8e890c1a upstream. dm-init should allow up to DM_MAX_{DEVICES,TARGETS} for devices/targets, and not DM_MAX_{DEVICES,TARGETS} - 1. Fix the checks and also fix the error message when the number of devices is surpassed. Fixes: 6bbc923d ("dm: add support to directly boot to a mapped device") Cc: stable@vger.kernel.org Signed-off-by:
-
Damien Le Moal authored
commit 7aedf75f upstream. The function blkdev_report_zones() returns success even if no zone information is reported (empty report). Empty zone reports can only happen if the report start sector passed exceeds the device capacity. The conditions for this to happen are either a bug in the caller code, or, a change in the device that forced the low level driver to change the device capacity to a value that is lower than the report start sector. This situation includes a failed disk revalidation resulting in the disk capacity being changed to 0. If this change happens while dm-zoned is in its initialization phase executing dmz_init_zones(), this function may enter an infinite loop and hang the system. To avoid this, add a check to disallow empty zone reports and bail out early. Also fix the function dmz_update_zone() to make sure that the report for the requested zone was correctly obtained. Fixes: 3b1a94c8 ("dm zoned: drive-managed zoned block device target") Cc: stable@vger.kernel.org Signed-off-by:
Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by:
Shaun Tancheff <shaun@tancheff.com> Signed-off-by:
-
Nikos Tsironis authored
commit e28adc3b upstream. Add missing dm_bitset_cursor_next() to properly advance the bitset cursor. Otherwise, the discarded state of all blocks is set according to the discarded state of the first block. Fixes: ae4a46a1 ("dm cache metadata: use bitset cursor api to load discard bitset") Cc: stable@vger.kernel.org Signed-off-by:
Nikos Tsironis <ntsironis@arrikto.com> Signed-off-by:
-
Stefan Mätje authored
commit 4ec73791 upstream. Due to an erratum in some Pericom PCIe-to-PCI bridges in reverse mode (conventional PCI on primary side, PCIe on downstream side), the Retrain Link bit needs to be cleared manually to allow the link training to complete successfully. If it is not cleared manually, the link training is continuously restarted and no devices below the PCI-to-PCIe bridge can be accessed. That means drivers for devices below the bridge will be loaded but won't work and may even crash because the driver is only reading 0xffff. See the Pericom Errata Sheet PI7C9X111SLB_errata_rev1.2_102711.pdf for details. Devices known as affected so far are: PI7C9X110, PI7C9X111SL, PI7C9X130. Add a new flag, clear_retrain_link, in struct pci_dev. Quirks for affected devices set this bit. Note that pcie_retrain_link() lives in aspm.c because that's currently the only place we use it, but this erratum is not specific to ASPM, and we may retrain links for other reasons in the future. Signed-off-by:
Stefan Mätje <stefan.maetje@esd.eu> [bhelgaas: apply regardless of CONFIG_PCIEASPM] Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> CC: stable@vger.kernel.org Signed-off-by:
-
Stefan Mätje authored
commit 86fa6a34 upstream. Factor out pcie_retrain_link() to use for Pericom Retrain Link quirk. No functional change intended. Signed-off-by:
-
Kazufumi Ikeda authored
commit be20bbcb upstream. Reestablish the PCIe link very early in the resume process in case it went down to prevent PCI accesses from hanging the bus. Such accesses can happen early in the PCI resume process, as early as the SUSPEND_RESUME_NOIRQ step, thus the link must be reestablished in the driver resume_noirq() callback. Fixes: e015f88c ("PCI: rcar: Add support for R-Car H3 to pcie-rcar") Signed-off-by:
Kazufumi Ikeda <kaz-ikeda@xc.jp.nec.com> Signed-off-by:
Gaku Inami <gaku.inami.xw@bp.renesas.com> Signed-off-by:
Marek Vasut <marek.vasut+renesas@gmail.com> [lorenzo.pieralisi@arm.com: reformatted commit log] Signed-off-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Acked-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: stable@vger.kernel.org Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Phil Edworthy <phil.edworthy@renesas.com> Cc: Simon Horman <horms+renesas@verge.net.au> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by:
-
Jisheng Zhang authored
commit 31f996ef upstream. Commit 60ed982a ("PCI/AER: Move internal declarations to drivers/pci/pci.h") changed pci_aer_init() to return "void", but didn't change the stub for when CONFIG_PCIEAER isn't enabled. Change the stub to match. Fixes: 60ed982a ("PCI/AER: Move internal declarations to drivers/pci/pci.h") Signed-off-by:
Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by:
-
Jean-Philippe Brucker authored
commit 6302bf3e upstream. Two functions allocate a host bridge: devm_pci_alloc_host_bridge() and pci_alloc_host_bridge(). At the moment, only the unmanaged one initializes the PCIe feature bits, which prevents from using features such as hotplug or AER on some systems, when booting with device tree. Make the initialization code common. Fixes: 02bfeb48 ("PCI/portdrv: Simplify PCIe feature permission checking") Signed-off-by:
Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Signed-off-by:
-
Lyude Paul authored
commit e0547c81 upstream. On ThinkPad P50 SKUs with an Nvidia Quadro M1000M instead of the M2000M variant, the BIOS does not always reset the secondary Nvidia GPU during reboot if the laptop is configured in Hybrid Graphics mode. The reason is unknown, but the following steps and possibly a good bit of patience will reproduce the issue: 1. Boot up the laptop normally in Hybrid Graphics mode 2. Make sure nouveau is loaded and that the GPU is awake 3. Allow the Nvidia GPU to runtime suspend itself after being idle 4. Reboot the machine, the more sudden the better (e.g. sysrq-b may help) 5. If nouveau loads up properly, reboot the machine again and go back to step 2 until you reproduce the issue This results in some very strange behavior: the GPU will be left in exactly the same state it was in when the previously booted kernel started the reboot. This has all sorts of bad side effects: for starters, this completely breaks nouveau starting with a mysterious EVO channel failure that happens well before we've actually used the EVO channel for anything: nouveau 0000:01:00.0: disp: chid 0 mthd 0000 data 00000400 00001000 00000002 This causes a timeout trying to bring up the GR ctx: nouveau 0000:01:00.0: timeout WARNING: CPU: 0 PID: 12 at drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgf100.c:1547 gf100_grctx_generate+0x7b2/0x850 [nouveau] Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET82W (1.55 ) 12/18/2018 Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper] ... nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1) nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1) nouveau 0000:01:00.0: fifo: fault 01 [WRITE] at 0000000000008000 engine 00 [GR] client 15 [HUB/SCC_NB] reason c4 [] on channel -1 [0000000000 unknown] The GPU never manages to recover. Booting without loading nouveau causes issues as well, since the GPU starts sending spurious interrupts that cause other device's IRQs to get disabled by the kernel: irq 16: nobody cared (try booting with the "irqpoll" option) ... handlers: [<000000007faa9e99>] i801_isr [i2c_i801] Disabling IRQ #16 ... serio: RMI4 PS/2 pass-through port at rmi4-00.fn03 i801_smbus 0000:00:1f.4: Timeout waiting for interrupt! i801_smbus 0000:00:1f.4: Transaction timeout rmi4_f03 rmi4-00.fn03: rmi_f03_pt_write: Failed to write to F03 TX register (-110). i801_smbus 0000:00:1f.4: Timeout waiting for interrupt! i801_smbus 0000:00:1f.4: Transaction timeout rmi4_physical rmi4-00: rmi_driver_set_irq_bits: Failed to change enabled interrupts! This causes the touchpad and sometimes other things to get disabled. Since this happens without nouveau, we can't fix this problem from nouveau itself. Add a PCI quirk for the specific P50 variant of this GPU. Make sure the GPU is advertising NoReset- so we don't reset the GPU when the machine is in Dedicated graphics mode (where the GPU being initialized by the BIOS is normal and expected). Map the GPU MMIO space and read the magic 0x2240c register, which will have bit 1 set if the device was POSTed during a previous boot. Once we've confirmed all of this, reset the GPU and re-disable it - bringing it back to a healthy state. Link: https://bugzilla.kernel.org/show_bug.cgi?id=203003 Link: https://lore.kernel.org/lkml/20190212220230.1568-1-lyude@redhat.comSigned-off-by:
Lyude Paul <lyude@redhat.com> Signed-off-by:
-
James Prestwood authored
commit 6afb7e26 upstream. When using PCI passthrough with this device, the host machine locks up completely when starting the VM, requiring a hard reboot. Add a quirk to avoid bus resets on this device. Fixes: c3e59ee4 ("PCI: Mark Atheros AR93xx to avoid bus reset") Link: https://lore.kernel.org/linux-pci/20190107213248.3034-1-james.prestwood@linux.intel.comSigned-off-by:
James Prestwood <james.prestwood@linux.intel.com> Signed-off-by:
-
Nikolai Kostrigin authored
commit d28ca864 upstream. ATS is broken on the Radeon R7 GPU (at least for Stoney Ridge based laptop) and causes IOMMU stalls and system failure. Disable ATS on these devices to make them usable again with IOMMU enabled. Thanks to Joerg Roedel <jroedel@suse.de> for help. [bhelgaas: In the email thread mentioned below, Alex suspects the real problem is in sbios or iommu, so it may affect only certain systems, and it may affect other devices in those systems as well. However, per Joerg we lack the ability to debug further, so this quirk is the best we can do for now.] Link: https://bugzilla.kernel.org/show_bug.cgi?id=194521 Link: https://lore.kernel.org/lkml/20190408103725.30426-1-nickel@altlinux.org Fixes: 9b44b0b0 ("PCI: Mark AMD Stoney GPU ATS as broken") Signed-off-by:
Nikolai Kostrigin <nickel@altlinux.org> Signed-off-by:
Joerg Roedel <jroedel@suse.de> CC: stable@vger.kernel.org Signed-off-by:
-
Yifeng Li authored
commit f627caf5 upstream. On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), blanking the display or starting the X server will crash and freeze the system, or garble the display. Experiments showed this problem can mostly be solved by adjusting the order of register writes. Also, sm712fb failed to consider the difference of clock frequency when unblanking the display, and programs the clock for SM712 to SM720. Fix them by adjusting the order of register writes, and adding an additional check for SM720 for programming the clock frequency. Signed-off-by:
Yifeng Li <tomli@tomli.me> Tested-by:
Sudip Mukherjee <sudipm.mukherjee@gmail.com> Cc: Teddy Wang <teddy.wang@siliconmotion.com> Cc: <stable@vger.kernel.org> # v4.4+ Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
-
Yifeng Li authored
commit 4ed7d2cc upstream. Loongson MIPS netbooks use 1024x600 LCD panels, which is the original target platform of this driver, but nearly all old x86 laptops have 1024x768. Lighting 768 panels using 600's timings would partially garble the display. Since it's not possible to distinguish them reliably, we change the default to 768, but keep 600 as-is on MIPS. Further, earlier laptops, such as IBM Thinkpad 240X, has a 800x600 LCD panel, this driver would probably garbled those display. As we don't have one for testing, the original behavior of the driver is kept as-is, but the problem has been documented is the comments. Signed-off-by:
-
Yifeng Li authored
commit 6053d3a4 upstream. In order to support the 1024x600 panel on Yeeloong Loongson MIPS laptop, the original 1024x768-16 table was modified to 1024x600-16, without leaving the original. It causes problem on x86 laptop as the 1024x768-16 support was still claimed but not working. Fix it by introducing the 1024x768-16 mode. Signed-off-by:
-
Yifeng Li authored
commit 9e0e5999 upstream. On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), running fbtest or X will crash the machine instantly, because the VRAM/framebuffer is not mapped correctly. On SM712, the framebuffer starts at the beginning of address space, but SM720's framebuffer starts at the 1 MiB offset from the beginning. However, sm712fb fails to take this into account, as a result, writing to the framebuffer will destroy all the registers and kill the system immediately. Another problem is the driver assumes 8 MiB of VRAM for SM720, but some SM720 system, such as this IBM Thinkpad, only has 4 MiB of VRAM. Fix this problem by removing the hardcoded VRAM size, adding a function to query the amount of VRAM from register MCR76 on SM720, and adding proper framebuffer offset. Please note that the memory map may have additional problems on Big-Endian system, which is not available for testing by myself. But I highly suspect that the original code is also broken on Big-Endian machines for SM720, so at least we are not making the problem worse. More, the driver also assumed SM710/SM712 has 4 MiB of VRAM, but it has a 2 MiB version as well, and used in earlier laptops, such as IBM Thinkpad 240X, the driver would probably crash on them. I've never seen one of those machines and cannot fix it, but I have documented these problems in the comments. Signed-off-by:
-
Yifeng Li authored
commit ec1587d5 upstream. When the machine is booted in VGA mode, loading sm712fb would cause a glitch of random pixels shown on the screen. To prevent it from happening, we first clear the entire framebuffer, and we also need to stop calling smtcfb_setmode() during initialization, the fbdev layer will call it for us later when it's ready. Signed-off-by:
-
Yifeng Li authored
commit 80690538 upstream. On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), rebooting with sm712fb framebuffer driver would cause a white screen of death on the next POST, presumably the proper timings for the LCD panel was not reprogrammed properly by the BIOS. Experiments showed a few CRTC Scratch Registers, including CRT3D, CRT3E and CRT3F may be used internally by BIOS as some flags. CRT3B is a hardware testing register, we shouldn't mess with it. CRT3C has blanking signal and line compare control, which is not needed for this driver. Stop writing to CR3B-CR3F (a.k.a CRT3B-CRT3F) registers. Even if these registers don't have side-effect on other systems, writing to them is also highly questionable. Signed-off-by:
-
Yifeng Li authored
commit dcf90705 upstream. On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), the amount of Video RAM is not detected correctly by the xf86-video-siliconmotion driver. This is because sm712fb overwrites the GPR71 Scratch Pad Register, which is set by BIOS on x86 and used to indicate amount of VRAM. Other Scratch Pad Registers, including GPR70/74/75, don't have the same side-effect, but overwriting to them is still questionable, as they are not related to modesetting. Stop writing to SR70/71/74/75 (a.k.a GPR70/71/74/75). Signed-off-by:
-
Yifeng Li authored
commit 5481115e upstream. On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), rebooting with sm712fb framebuffer driver would cause the role of brightness up/down button to swap. Experiments showed the FPR30 register caused this behavior. Moreover, even if this register don't have side-effect on other systems, over- writing it is also highly questionable, since it was originally configurated by the motherboard manufacturer by hardwiring pull-down resistors to indicate the type of LCD panel. We should not mess with it. Stop writing to the SR30 (a.k.a FPR30) register. Signed-off-by:
-
Ard Biesheuvel authored
commit f8585539 upstream. The following commit: 38ac0287 ("fbdev/efifb: Honour UEFI memory map attributes when mapping the FB") updated the EFI framebuffer code to use memory mappings for the linear framebuffer that are permitted by the memory attributes described by the EFI memory map for the particular region, if the framebuffer happens to be covered by the EFI memory map (which is typically only the case for framebuffers in shared memory). This is required since non-x86 systems may require cacheable attributes for memory mappings that are shared with other masters (such as GPUs), and this information cannot be described by the Graphics Output Protocol (GOP) EFI protocol itself, and so we rely on the EFI memory map for this. As reported by James, this breaks some x86 systems: [ 1.173368] efifb: probing for efifb [ 1.173386] efifb: abort, cannot remap video memory 0x1d5000 @ 0xcf800000 [ 1.173395] Trying to free nonexistent resource <00000000cf800000-00000000cf9d4bff> [ 1.173413] efi-framebuffer: probe of efi-framebuffer.0 failed with error -5 The problem turns out to be that the memory map entry that describes the framebuffer has no memory attributes listed at all, and so we end up with a mem_flags value of 0x0. So work around this by ensuring that the memory map entry's attribute field has a sane value before using it to mask the set of usable attributes. Reported-by:
James Hilliard <james.hilliard1@gmail.com> Tested-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: <stable@vger.kernel.org> # v4.19+ Cc: Borislav Petkov <bp@alien8.de> Cc: James Morse <james.morse@arm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Peter Jones <pjones@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Fixes: 38ac0287 ("fbdev/efifb: Honour UEFI memory map attributes when ...") Link: http://lkml.kernel.org/r/20190516213159.3530-2-ard.biesheuvel@linaro.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Dave Hansen authored
commit 5a28fc94 upstream. This is a bit of a mess, to put it mildly. But, it's a bug that only seems to have showed up in 4.20 but wasn't noticed until now, because nobody uses MPX. MPX has the arch_unmap() hook inside of munmap() because MPX uses bounds tables that protect other areas of memory. When memory is unmapped, there is also a need to unmap the MPX bounds tables. Barring this, unused bounds tables can eat 80% of the address space. But, the recursive do_munmap() that gets called vi arch_unmap() wreaks havoc with __do_munmap()'s state. It can result in freeing populated page tables, accessing bogus VMA state, double-freed VMAs and more. See the "long story" further below for the gory details. To fix this, call arch_unmap() before __do_unmap() has a chance to do anything meaningful. Also, remove the 'vma' argument and force the MPX code to do its own, independent VMA lookup. == UML / unicore32 impact == Remove unused 'vma' argument to arch_unmap(). No functional change. I compile tested this on UML but not unicore32. == powerpc impact == powerpc uses arch_unmap() well to watch for munmap() on the VDSO and zeroes out 'current->mm->context.vdso_base'. Moving arch_unmap() makes this happen earlier in __do_munmap(). But, 'vdso_base' seems to only be used in perf and in the signal delivery that happens near the return to userspace. I can not find any likely impact to powerpc, other than the zeroing happening a little earlier. powerpc does not use the 'vma' argument and is unaffected by its removal. I compile-tested a 64-bit powerpc defconfig. == x86 impact == For the common success case this is functionally identical to what was there before. For the munmap() failure case, it's possible that some MPX tables will be zapped for memory that continues to be in use. But, this is an extraordinarily unlikely scenario and the harm would be that MPX provides no protection since the bounds table got reset (zeroed). I can't imagine anyone doing this: ptr = mmap(); // use ptr ret = munmap(ptr); if (ret) // oh, there was an error, I'll // keep using ptr. Because if you're doing munmap(), you are *done* with the memory. There's probably no good data in there _anyway_. This passes the original reproducer from Richard Biener as well as the existing mpx selftests/. The long story: munmap() has a couple of pieces: 1. Find the affected VMA(s) 2. Split the start/end one(s) if neceesary 3. Pull the VMAs out of the rbtree 4. Actually zap the memory via unmap_region(), including freeing page tables (or queueing them to be freed). 5. Fix up some of the accounting (like fput()) and actually free the VMA itself. This specific ordering was actually introduced by: dd2283f2 ("mm: mmap: zap pages with read mmap_sem in munmap") during the 4.20 merge window. The previous __do_munmap() code was actually safe because the only thing after arch_unmap() was remove_vma_list(). arch_unmap() could not see 'vma' in the rbtree because it was detached, so it is not even capable of doing operations unsafe for remove_vma_list()'s use of 'vma'. Richard Biener reported a test that shows this in dmesg: [1216548.787498] BUG: Bad rss-counter state mm:0000000017ce560b idx:1 val:551 [1216548.787500] BUG: non-zero pgtables_bytes on freeing mm: 24576 What triggered this was the recursive do_munmap() called via arch_unmap(). It was freeing page tables that has not been properly zapped. But, the problem was bigger than this. For one, arch_unmap() can free VMAs. But, the calling __do_munmap() has variables that *point* to VMAs and obviously can't handle them just getting freed while the pointer is still in use. I tried a couple of things here. First, I tried to fix the page table freeing problem in isolation, but I then found the VMA issue. I also tried having the MPX code return a flag if it modified the rbtree which would force __do_munmap() to re-walk to restart. That spiralled out of control in complexity pretty fast. Just moving arch_unmap() and accepting that the bonkers failure case might eat some bounds tables seems like the simplest viable fix. This was also reported in the following kernel bugzilla entry: https://bugzilla.kernel.org/show_bug.cgi?id=203123 There are some reports that this commit triggered this bug: dd2283f2 ("mm: mmap: zap pages with read mmap_sem in munmap") While that commit certainly made the issues easier to hit, I believe the fundamental issue has been with us as long as MPX itself, thus the Fixes: tag below is for one of the original MPX commits. [ mingo: Minor edits to the changelog and the patch. ] Reported-by:
Richard Biener <rguenther@suse.de> Reported-by:
H.J. Lu <hjl.tools@gmail.com> Signed-off-by:
Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Yang Shi <yang.shi@linux.alibaba.com> Acked-by:
Michael Ellerman <mpe@ellerman.id.au> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jeff Dike <jdike@addtoit.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Richard Weinberger <richard@nod.at> Cc: Rik van Riel <riel@surriel.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: linux-arch@vger.kernel.org Cc: linux-mm@kvack.org Cc: linux-um@lists.infradead.org Cc: linuxppc-dev@lists.ozlabs.org Cc: stable@vger.kernel.org Fixes: dd2283f2 ("mm: mmap: zap pages with read mmap_sem in munmap") Link: http://lkml.kernel.org/r/20190419194747.5E1AD6DC@viggo.jf.intel.comSigned-off-by:
-
Nathan Chancellor authored
commit 8ea58f1e upstream. Currently, this Makefile hardcodes GNU ar, meaning that if it is not available, there is no way to supply a different one and the build will fail. $ make AR=llvm-ar CC=clang LD=ld.lld HOSTAR=llvm-ar HOSTCC=clang \ HOSTLD=ld.lld HOSTLDFLAGS=-fuse-ld=lld defconfig modules_prepare ... AR /out/tools/objtool/libsubcmd.a /bin/sh: 1: ar: not found ... Follow the logic of HOST{CC,LD} and allow the user to specify a different ar tool via HOSTAR (which is used elsewhere in other tools/ Makefiles). Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Reviewed-by:
Mukesh Ojha <mojha@codeaurora.org> Cc: <stable@vger.kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/80822a9353926c38fd7a152991c6292491a9d0e8.1558028966.git.jpoimboe@redhat.com Link: https://github.com/ClangBuiltLinux/linux/issues/481Signed-off-by:
-
Florian Fainelli authored
commit 1b1f01b6 upstream. arch/mips/kernel/perf_event_mipsxx.c: In function 'mipsxx_pmu_enable_event': arch/mips/kernel/perf_event_mipsxx.c:326:21: error: unused variable 'event' [-Werror=unused-variable] struct perf_event *event = container_of(evt, struct perf_event, hw); ^~~~~ Fix this by making use of IS_ENABLED() to simplify the code and avoid unnecessary ifdefery. Fixes: 84002c88 ("MIPS: perf: Fix perf with MT counting other threads") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Paul Burton <paul.burton@mips.com> Cc: linux-mips@linux-mips.org Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@vger.kernel.org Cc: stable@vger.kernel.org # v4.18+ Signed-off-by:
-
