- 11 Dec, 2015 27 commits
-
-
Arend van Spriel authored
Got a hint on IRC that a 43242 dongle for LG smart TV's works with brcmfmac: > Hello - I recently got a LG AN-WF500 wireless dongle for LG's SmartTVs. > From the information I gathered it uses a Broadcom chipset BCM43242. > The device should have been supported by brcmfmac kernel driver if it used > USB IDs 0a5c:bd1f. > My device however identifies itself as "ID 043e:3101 LG Electronics USA, Inc.". > I then tried adding the USB ID to the driver with > "echo "043e 3101" > /sys/bus/usb/drivers/brcmfmac/new_id" and it just works. > The kernel provides the following information. > [15958.851291] usb 3-1.1.3: new high-speed USB device number 53 using ehci-pci > [15958.946723] usb 3-1.1.3: New USB device found, idVendor=043e, idProduct=3101 > [15958.946728] usb 3-1.1.3: New USB device strings: Mfr=1, Product=4, SerialNumber=3 > [15958.946731] usb 3-1.1.3: Product: Composite Wireless Adapter > [15958.946733] usb 3-1.1.3: Manufacturer: Broadcom > [15958.946735] usb 3-1.1.3: SerialNumber: 28458 Reported-by:
Johannes Berg <johannes@sipsolutions.net> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Kosuke Tatsukawa authored
brcmf_msgbuf_ioctl_resp_wake() seems to be missing a memory barrier which might cause the waker to not notice the waiter and miss sending a wake_up as in the following figure. brcmf_msgbuf_ioctl_resp_wake brcmf_msgbuf_ioctl_resp_wait ------------------------------------------------------------------------ if (waitqueue_active(&msgbuf->ioctl_resp_wait)) /* The CPU might reorder the test for the waitqueue up here, before prior writes complete */ /* wait_event_timeout */ /* __wait_event_timeout */ /* ___wait_event */ prepare_to_wait_event(&wq, &__wait, state); if (msgbuf->ctl_completed) ... msgbuf->ctl_completed = true; schedule_timeout(__ret)) ------------------------------------------------------------------------ There are three other place in drivers/net/wireless/brcm80211/brcmfmac/ which have similar code. The attached patch removes the call to waitqueue_active() leaving just wake_up() behind. This fixes the problem because the call to spin_lock_irqsave() in wake_up() will be an ACQUIRE operation. I found this issue when I was looking through the linux source code for places calling waitqueue_active() before wake_up*(), but without preceding memory barriers, after sending a patch to fix a similar issue in drivers/tty/n_tty.c (Details about the original issue can be found here: https://lkml.org/lkml/2015/9/28/849). Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by:
Kosuke Tatsukawa <tatsu@ab.jp.nec.com> Signed-off-by:
-
Hante Meuleman authored
IBSS got broken over time. Disconnect events should not be given for IBSS mode and connect events for IBSS need to have channel information. Reviewed-by:
-
Arend van Spriel authored
The interface combinations are intended for use-case in which the driver handles multiple interface concurrently. This means that the combinations do not need to be checked when there is only a single interface active. Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
No need to pass timing configuration in local functions as they are static anyway. Reviewed-by:
-
Arnd Bergmann authored
With the new optimized do_div() code, some versions of gcc produce obviously incorrect code that leads to a link error in iwlegacy/common.o: drivers/built-in.o: In function `il_send_rxon_timing': :(.text+0xa6b4d4): undefined reference to `____ilog2_NaN' :(.text+0xa6b4f0): undefined reference to `__aeabi_uldivmod' In a few thousand randconfig builds, I have seen this problem a couple of times in this file, but never anywhere else in the kernel, so we can try to work around this in the only file that shows the behavior, by marking the il_adjust_beacon_interval function as noinline, which convinces gcc to use the unoptimized do_div() all the time. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Nicolas Pitre <nico@linaro.org> Acked-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Peter Wu authored
Free skb for received frames with a wrong checksum. This can happen pretty rapidly, exhausting all memory. This fixes a memleak (detected with kmemleak). Originally found while using monitor mode, but it also appears during managed mode (once the link is up). Cc: stable@vger.kernel.org Signed-off-by:
Peter Wu <peter@lekensteyn.nl> ACKed-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Julia Lawall authored
Move constants to the right of binary operators. Generated by: scripts/coccinelle/misc/compare_const_fl.cocci Signed-off-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
Julia Lawall <julia.lawall@lip6.fr> Signed-off-by:
-
Julia Lawall authored
Remove unneeded semicolon. Generated by: scripts/coccinelle/misc/semicolon.cocci Signed-off-by:
-
Julia Lawall authored
Move constants to the right of binary operators. Generated by: scripts/coccinelle/misc/compare_const_fl.cocci Signed-off-by:
-
Amitkumar Karwar authored
EU is not a valid country in db.txt file. Hence regulatory_hint returns failure if EEPROM provides region code as 0x30. Let's use FR for 0x30. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Cathy Luo <cluo@marvell.com> Signed-off-by:
-
Amitkumar Karwar authored
If device has already received country information from EEPROM, we won't parse AP's country IE and download it to firmware. We will also set regulatory flags to disable beacon hints and ignore country IE. Signed-off-by:
-
Amitkumar Karwar authored
Driver gets country information from EEPROM during initialization. We will call regulatory_hint to update current regulatory domain. As by default world regulatory domain is selected by cfg80211, country '00' from EEPROM is ignored. Signed-off-by:
-
Amitkumar Karwar authored
It's been observed that even if firmware returns an error for a configuration command, we go ahead and start AP. This patch changes the command type from async to sync so that threads waits for command response and return failure start AP. Signed-off-by:
-
Amitkumar Karwar authored
Even if ADHOC start or join attempt is failed, these commands are returned with success status by firmware. Actual connection result is provided inside command response. This patch parses the adhoc connection result and resets connection state variables if connection is not successful. Signed-off-by:
-
Dan Carpenter authored
This code was supposed to trigger a BUG() if we truncate the output but it's off by one so it allows one character to be truncated. Really drivers shouldn't call BUG_ON() and especially for something minor like this so I've changed it to a WARN_ON(). Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Dan Carpenter authored
The current code returns success if prism2_init_local_data() fails, but we want to return an error code. Also we can remove the bogus ret initializer because it is wrong and never used. Signed-off-by:
-
Dan Carpenter authored
We already know that "wep_key->key_length" is set so there is no need to check again. Also the last curly brace was indented too far. Signed-off-by:
-
Dan Carpenter authored
This code causes a static checker warning because we check for "if (ret == 0)" but we have already had verified that was true. Clean it up a little. Signed-off-by:
-
Dan Carpenter authored
If the mode is NL80211_IFTYPE_UNSPECIFIED then we return success at the start of the function so this condition is never true. Signed-off-by:
-
Colin Ian King authored
There is a null ptr check for fws to set bcmc_credit_check, however, there a lock and unlock on fws should only performed if fwts is also not null to also avoid a potential null pointer deference. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Acked-by:
-
Guy Mishol authored
Align to new wl18xx sg parameters. This requires to split both wl12xx/wl18xx enumerators. Signed-off-by:
Guy Mishol <guym@ti.com> Acked-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
- 09 Dec, 2015 13 commits
-
-
Julia Lawall authored
The cmac_ops structures are never modified, so declare them as const. Done with the help of Coccinelle. Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
These fields are updated but never read. Remove the overhead. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Eric Dumazet authored
Under heavy TX load, bnx2x_poll() can loop forever and trigger soft lockup bugs. A napi poll handler must yield after one TX completion round, risk of livelock is too high otherwise. Bug is very easy to trigger using a debug build, and udp flood, because of added cpu cycles in TX completion, and we do not receive enough packets to break the loop. Reported-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Herbert Xu authored
The patch 9497df88 ("rhashtable: Fix reader/rehash race") added a pair of barriers. In fact the wmb is superfluous because every subsequent write to the old or new hash table uses rcu_assign_pointer, which itself carriers a full barrier prior to the assignment. Therefore we may remove the explicit wmb. Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Acked-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
David S. Miller authored
Hariprasad Shenai says: ==================== Update Kconfig and some fixes for cxgb4 This series update Kconfig to add description for Chelsio's next generation T6 family of adapters, also fixes ethtool stats alignment and prevents simultaneous execution of service_ofldq thread, deals with queue wrap around and adds some fl counters for debugging purpose and device ID for new T5 adapters. This patch series has been created against net-next tree and includes patches on cxgb4 driver. We have included all the maintainers of respective drivers. Kindly review the change and let us know in case of any review comments. Thanks V2: Declare 'service_ofldq_running' as bool in Patch 4/7 ("cxgb4: prevent simultaneous execution of service_ofldq()") based on review comment by David Miller ==================== Signed-off-by: -
Hariprasad Shenai authored
Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
Add Free List DMA Mapping Errors to SGE Queue info for Free Lists. Add Free List "Low" counter to count the number of times we see the number of pointers that we _think_ the hardware sees in the Free List below the Egress Threshold. Signed-off-by:
-
Hariprasad Shenai authored
The WR headers may not fit within one descriptor. So we need to deal with wrap-around here. Based on original patch by Pranjal Joshi <pjoshi@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
Change mutual exclusion mechanism to prevent multiple threads of execution from running in service_ofldq() at the same time. The old mechanism used an implicit guard on the down-call path and none on the restart path and wasn't working. This checking makes the mechanism explicit and is much easier to understand as a result. Based on original work by Casey Leedom <leedom@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
Use helper macro ACCESS_ONCE() to load from the SGE status page to prevent the compiler loading multiple times. Based on original work by Mike Werner <werner@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
Signed-off-by:
-
Hariprasad Shenai authored
Signed-off-by:
-
yankejian authored
here is the patch raising the performance of XGE by: 1)changes the way page management method for enet momery, and 2)reduces the count of rmb, and 3)adds Memory prefetching Signed-off-by:
Kejian Yan <yankejian@huawei.com> Signed-off-by:
-
