Some gigabytes have on-board SIMG5723s connected to JMB ahcis.  These
are used to implement hardware raid.  Unfortunately some firmware
revisions on these 5723s don't bring the link down when all the
downstream ports are unoccupied while not responding to reset protocol
which makes libata think that there's device attached to the port but
is not responding and retry.  This results in painfully wrong boot
detection time for these ports when they're empty.

This patch quirks those boards such that ahci gives up after the
initial timeout.  Combined with parallel probing, this gives quick
enough probing and also is safe because SIMG5723 will respond to the
first try if any of the downstream ports is occupied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marc Bowes <marcbowes@gmail.com>
Reported-by: Nicolas Mailhot <Nicolas.Mailhot@LaPoste.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Too strong words led to spurious bug reports: Novell bugzilla #527748,
RedHat bugzilla #468800. This patch is used to soften up the dmesg on
SB600 PMP softreset failure recovery, so as to remove the scariness and
concern from community.
Reported-by: pgnet Dev <pgnet.dev@gmail.com>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

By default the kernel honors the HPA (host protected area) of hard
drives.  Using libata's ignore_hpa module option it's possible to
change this behaviour.

Document usage and options of libata.ignore_hpa in
Documentation/kernel-parameters.txt.
Signed-off-by: Michael Prokop <mika@grml.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

At least the nVidia MCP55 controller quite happily supports MSI.
This adds an option to use it. It is disabled by default.
As per feedback by Robert Hancock, it will honour the user
request as the kernel will not enable MSI where the controller
or the specific system configuration do not support it.
Signed-off-by: Tony Vroon <tony@linx.net>
Cc: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

OCZ Vertex SSD can't do HPA and not in a usual way.  It reports HPA,
allows unlocking but then fails all IOs which fall in the unlocked
area.  Quirk it so that HPA unlocking is not used for the device.

Reported by Daniel Perup in bnc#522414.

 https://bugzilla.novell.com/show_bug.cgi?id=522414Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Daniel Perup <probe@spray.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

PIO and MWDMA timings are never programmed for the second channel
because timing registers are treated as 16-bit long ones.

The bug is an attixp -> pata_atiixp regression and goes back to:

	commit 669a5db4
	Author: Jeff Garzik <jeff@garzik.org>
	Date:   Tue Aug 29 18:12:40 2006 -0400

	    [libata] Add a bunch of PATA drivers.

Cc: Krystian Juskowiak <jusko@tlen.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Julias Lawall discovered that pata_at91 wasn't freeing a memory region
allocated with kzalloc() on init failure paths.  Upon review,
pata_at91 also seems to be doing unnecessary explicit resource
releases for managed resources too.  Convert memory allocation to
managed one and drop unnecessary explicit resource releases.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Julia Lawall <julia@diku.dk>
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/fyu/linux-2.6:
  arch/ia64/kernel/iosapic: missing test after ioremap()
  ia64/topology.c: exit cache_add_dev when kobject_init_and_add fails
  arch/ia64/Makefile: Remove -mtune=merced in IA64 kernel build
  IA64: includecheck fix: ia64, pgtable.h
  IA64: includecheck fix: ia64, ia64_ksyms.c
  ia64: boolean __test_and_clear_bit
  Bug Fix arch/ia64/kernel/pci-dma.c: fix recursive dma_supported() call in iommu_dma_supported()

Missing test after ioremap()
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>

Make cache_add_dev exit sysfs when kobject_init_and_add returns an error.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>

Between GCC version 3.4.0 and 4.3.3 (including 3.4.0 and 4.3.3), -mtune=merced
is implemented in GCC. Starting from 4.4.0, -mtune=merced is deprecated.

Even implemented in versions between 3.4.0 and 4.3.3, the -mtune=merced
feature has been broken in some of the versions. For example, GCC 4.1.2 reports
interanl tuning function errors during kernel building with -mtune=merced. Or
GCC Bugzilla 16130 reports another -mtune=merced issue on GCC 3.4.1.

So I would remove the -mtune=merced from IA64 kernel build. Without this option,
kernel on Merced will remain the same except losing an unstable and out-of-date
performance tunning feature.

Since GCC version 3.4.0, -mtune=mckinley has been implemented. The
-mtune=mckinley option functions the same as mtune=itanium2. And mtune=itanium2
is the default option. So we don't need to add mtune=mckinley either since its
been the default option in any GCC version which implements this option.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>

fix the following 'make includecheck' warning:

  arch/ia64/include/asm/pgtable.h: asm/processor.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>

fix the following 'make includecheck' warning:

  arch/ia64/kernel/ia64_ksyms.c: asm/page.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>

__test_and_clear_bit() returns a bitfield with the tested-for bit set.
Make it consistent with the other bitops - of ia64 but also every
other architecture - and return a boolean value.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>

In commit 160c1d8e,
dma_ops->dma_supported = iommu_dma_supported;

This dma_ops->dma_supported is first called in platform_dma_init() during kernel
boot. Then dma_ops->dma_supported will be called recursively in
iommu_dma_supported.

Kernel can not boot because kernel can not get out of iommu_dma_supported until
it runs out of stack memory.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  SELinux: fix memory leakage in /security/selinux/hooks.c

Fix memory leakage in /security/selinux/hooks.c

The buffer always needs to be freed here; we either error
out or allocate more memory.
Reported-by: iceberg <strakh@ispras.ru>
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>

Commit 783ea7d4
(Driver Core: Rework platform suspend/resume, print warning)
added a warning message printed for platform drivers that use the
legacy PM callbacks rather than struct dev_pm_ops.  Unfortunately,
this resulted in some confusion and made some people try to convert
drivers by replacing the old callbacks with struct dev_pm_ops in
automatic way, which generally is not a good idea.

Remove the platform device runtime dev_pm_ops warning for now,
because it's annoying to users and it's not really necessary right
now.

[rjw: Modified the changelog to be more informative.]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Commit d945cb9c ("pty: Rework the pty layer to use the normal buffering
logic") dropped the test for 'tty->stopped' in pty_write_room(), which
then causes the n_tty line discipline thing to not throttle the data
properly when the tty is stopped.

So instead of pausing the write due to the tty being stopped, the ldisc
layer would go ahead and push it down to the pty.  The pty write()
routine would then refuse to take the data (because it _did_ check
'stopped'), and the data wouldn't actually be written.

This whole stopped test should eventually be moved into the tty ldisc
layer rather than have low-level tty drivers care about these things,
but right now the fix is to just re-instate the missing pty 'stopped'
handling.
Reported-and-tested-by: Artur Skawina <art.08.09@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
  perf_counter: Zero dead bytes from ftrace raw samples size alignment
  perf_counter: Subtract the buffer size field from the event record size
  perf_counter: Require CAP_SYS_ADMIN for raw tracepoint data
  perf_counter: Correct PERF_SAMPLE_RAW output
  perf tools: callchain: Fix bad rounding of minimum rate
  perf_counter tools: Fix libbfd detection for systems with libz dependency
  perf: "Longum est iter per praecepta, breve et efficax per exempla"
  perf_counter: Fix a race on perf_counter_ctx
  perf_counter: Fix tracepoint sampling to be part of generic sampling
  perf_counter: Work around gcc warning by initializing tracepoint record unconditionally
  perf tools: callchain: Fix sum of percentages to be 100% by displaying amount of ignored chains in fractal mode
  perf tools: callchain: Fix 'perf report' display to be callchain by default
  perf tools: callchain: Fix spurious 'perf report' warnings: ignore empty callchains
  perf record: Fix the -A UI for empty or non-existent perf.data
  perf util: Fix do_read() to fail on EOF instead of busy-looping
  perf list: Fix the output to not include tracepoints without an id
  perf_counter/powerpc: Fix oops on cpus without perf_counter hardware support
  perf stat: Fix tool option consistency: rename -S/--scale to -c/--scale
  perf report: Add debug help for the finding of symbol bugs - show the symtab origin (DSO, build-id, kernel, etc)
  perf report: Fix per task mult-counter stat reporting
  ...

Merge branch 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86/irq: Fix move_irq_desc() for nodes without ram

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Fix serialization in pit_expect_msb()

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI hotplug: SGI hotplug: do not use hotplug_slot_attr
  PCI hotplug: SGI hotplug: fix build failure

Wei Chong Tan reported a fast-PIT-calibration corner-case:

| pit_expect_msb() is vulnerable to SMI disturbance corner case
| in some platforms which causes /proc/cpuinfo to show wrong
| CPU MHz value when quick_pit_calibrate() jumps to success
| section.

I think that the real issue isn't even an SMI - but the fact
that in the very last iteration of the loop, there's no
serializing instruction _after_ the last 'rdtsc'. So even in
the absense of SMI's, we do have a situation where the cycle
counter was read without proper serialization.

The last check should be done outside the outer loop, since
_inside_ the outer loop, we'll be testing that the PIT has
the right MSB value has the right value in the next iteration.

So only the _last_ iteration is special, because that's the one
that will not check the PIT MSB value any more, and because the
final 'get_cycles()' isn't serialized.

In other words:

 - I'd like to move the PIT MSB check to after the last
   iteration, rather than in every iteration

 - I think we should comment on the fact that it's also a
   serializing instruction and so 'fences in' the TSC read.

Here's a suggested replacement.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: "Tan, Wei Chong" <wei.chong.tan@intel.com>
Tested-by: "Tan, Wei Chong" <wei.chong.tan@intel.com>
LKML-Reference: <B28277FD4E0F9247A3D55704C440A140D5D683F3@pgsmsx504.gar.corp.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  mm_for_maps: take ->cred_guard_mutex to fix the race with exec
  mm_for_maps: shift down_read(mmap_sem) to the caller
  mm_for_maps: simplify, use ptrace_may_access()

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/dma: pci_set_dma_mask() shouldn't fail if mask fits in RAM

Fix the following 'make includecheck' warning:

  arch/mn10300/include/asm/pci.h: linux/mm.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

clean up type-casting twice.  "size_t" is typedef as "unsigned long" in
64-bit system, and "unsigned int" in 32-bit system, and the intermediate
cast to 'long' is pointless.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This will register the ioctl range used by nilfs2 file system to the
table listed in Documentation/ioctl/ioctl-number.txt.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

After aligning the ftrace raw samples, there are dead bytes storing
random data from the stack. We don't want to leak these to userspace,
then zero these out.

Before:

	0x2de88 [0x50]: event: 9
	.
	. ... raw event: size 80 bytes
	.  0000:  09 00 00 00 01 00 50 00 d0 c7 00 81 ff ff ff ff  ......P........
	.  0010:  68 01 00 00 68 01 00 00 2c 00 00 00 00 00 00 00  h...h...,......
	.  0020:  2c 00 00 00 2b 00 01 02 68 01 00 00 68 01 00 00  ,...+...h...h..
	.  0030:  6b 6f 6e 64 65 6d 61 6e 64 2f 30 00 00 00 00 00  kondemand/0....
	.  0040:  68 01 00 00 40 7f 46 81 ff ff ff ff 00 10 1b 7f  h...@.F........
                                                      ^  ^  ^  ^
                                                         Leak

After:

	0x2d318 [0x50]: event: 9
	.
	. ... raw event: size 80 bytes
	.  0000:  09 00 00 00 01 00 50 00 d0 c7 00 81 ff ff ff ff  ......P........
	.  0010:  68 01 00 00 68 01 00 00 68 14 00 00 00 00 00 00  h...h...h......
	.  0020:  2c 00 00 00 2b 00 01 02 68 01 00 00 68 01 00 00  ,...+...h...h..
	.  0030:  6b 6f 6e 64 65 6d 61 6e 64 2f 30 00 00 00 00 00  kondemand/0....
	.  0040:  68 01 00 00 a0 80 46 81 ff ff ff ff 00 00 00 00  h.....F........
                                                      ^  ^  ^  ^
							 Fixed
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1249915116-5210-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>

We compute the perf raw sample size by aligning the raw ftrace
event size plus the buffer size field itself. We do that
instead of aligning only the perf raw sample size, so that we
might economize some in some cases.

But this buffer size field is not stored in the perf raw
sample, we must then substract its size from the buffer once we
computed the alignment unless we may get a useless u32 field in
the buffer.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090810141129.GA5124@nowhere>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

The problem is minor, but without ->cred_guard_mutex held we can race
with exec() and get the new ->mm but check old creds.

Now we do not need to re-check task->mm after ptrace_may_access(), it
can't be changed to the new mm under us.

Strictly speaking, this also fixes another very minor problem. Unless
security check fails or the task exits mm_for_maps() should never
return NULL, the caller should get either old or new ->mm.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>

mm_for_maps() takes ->mmap_sem after security checks, this looks
strange and obfuscates the locking rules. Move this lock to its
single caller, m_start().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>

It would be nice to kill __ptrace_may_access(). It requires task_lock(),
but this lock is only needed to read mm->flags in the middle.

Convert mm_for_maps() to use ptrace_may_access(), this also simplifies
the code a little bit.

Also, we do not need to take ->mmap_sem in advance. In fact I think
mm_for_maps() should not play with ->mmap_sem at all, the caller should
take this lock.

With or without this patch, without ->cred_guard_mutex held we can race
with exec() and get the new ->mm but check old creds.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>

Raw tracepoint data contains various kernel internals and
data from other users, so restrict this to CAP_SYS_ADMIN.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1249896452.17467.75.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

PERF_SAMPLE_* output switches should unconditionally output the
correct format, as they are the only way to unambiguously parse
the PERF_EVENT_SAMPLE data.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1249896447.17467.74.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

On an iMac G5, the b43 driver is failing to initialise because trying to
set the dma mask to 30-bit fails. Even though there's only 512MiB of RAM
in the machine anyway:
	https://bugzilla.redhat.com/show_bug.cgi?id=514787

We should probably let it succeed if the available RAM in the system
doesn't exceed the requested limit.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

* 'for-linus' of git://git.infradead.org/ubi-2.6:
  UBI: compatible fallback in absense of sequence numbers
  UBI: fix double free on error path

* 'kvm-updates/2.6.31' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: Avoid redelivery of edge interrupt before next edge
  KVM: MMU: limit rmap chain length
  KVM: ia64: fix build failures due to ia64/unsigned long mismatches
  KVM: Make KVM_HPAGES_PER_HPAGE unsigned long to avoid build error on powerpc
  KVM: fix ack not being delivered when msi present
  KVM: s390: fix wait_queue handling
  KVM: VMX: Fix locking imbalance on emulation failure
  KVM: VMX: Fix locking order in handle_invalid_guest_state
  KVM: MMU: handle n_free_mmu_pages > n_alloc_mmu_pages in kvm_mmu_change_mmu_pages
  KVM: SVM: force new asid on vcpu migration
  KVM: x86: verify MTRR/PAT validity
  KVM: PIT: fix kpit_elapsed division by zero
  KVM: Fix KVM_GET_MSR_INDEX_LIST

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/i915: silence vblank warnings
  drm: silence pointless vblank warning.
  drm: When adding probed modes, preserve duplicate mode types