- 20 May, 2010 40 commits
-
-
Johan Hovold authored
Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Johan Hovold authored
No need to raise dtr/rts in open as this is taken care of by tty layer. Signed-off-by:
-
Johan Hovold authored
Compile-only tested. Signed-off-by:
-
Johan Hovold authored
Use dynamically allocated urb for baudrate changes rather than unconditionally submitting the port write urb which may already be in use. Compile-only tested. Signed-off-by:
-
Johan Hovold authored
Use usb_serial_driver bulk_in_size and bulk_out_size to make sure buffers of appropriate sizes are allocated in the first place rather than reallocating them at every open. Signed-off-by:
-
Johan Hovold authored
If the user specifies a custom bulk buffer size we get a double free at port release. Cc: stable <stable@kernel.org> Signed-off-by:
-
Alan Stern authored
This patch (as1380) fixes a bug in the wakeup settings for EHCI host controllers. When the controller is suspended, if it isn't enabled for remote wakeup then we have to turn off all the port wakeup flags. Disabling PCI PME# isn't good enough, because some systems (Intel) evidently use alternate wakeup signalling paths. In addition, the patch improves the handling of the Intel Moorestown hardware by performing various power-up and power-down delays just once instead of once for each port (i.e., the delays are moved outside of the port loops). This requires extra code, but the total delay time is reduced. There are also a few additional minor cleanups. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Ondrej Zary <linux@rainbow-software.org> CC: Alek Du <alek.du@intel.com> CC: stable <stable@kernel.org> Signed-off-by:
-
Alek Du authored
This is a bug fix for PHCD (phy clock disable) low power feature: After PHCD is set, any write to PORTSC register is illegal, so when resume ports, clear PHCD bit first. Signed-off-by:
Alek Du <alek.du@intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by:
-
Randy Dunlap authored
Fix functionfs build to handle CONFIG_NET not enabled, to prevent these build errors: ERROR: "netif_carrier_on" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "netif_carrier_off" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_realloc_headroom" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_trim" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "netif_rx" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "alloc_etherdev_mq" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "ethtool_op_get_link" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "free_netdev" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "register_netdev" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_push" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_pull" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "dev_kfree_skb_any" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_queue_tail" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "__alloc_skb" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "eth_type_trans" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "eth_validate_addr" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_dequeue" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "unregister_netdev" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "__netif_schedule" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_put" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "eth_mac_addr" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "dev_get_stats" [drivers/usb/gadget/g_ffs.ko] undefined! Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Acked-by:
Michał Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by:
-
William Gulland authored
Our virtual xHCI device can have as many ports as we like - I've tested this patch with 31. Signed-off-by:
William Gulland <wgulland@vmware.com> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
Ming Lei authored
Now on one uses this function and it seems useless, so remove usb_find_device. [tom@tom linux-2.6-next]$ grep -r -n -I usb_find_device ./ drivers/media/dvb/dvb-usb/dvb-usb-init.c:160:static struct dvb_usb_device_description * dvb_usb_find_device(struct usb_device *udev,struct dvb_usb_device_properties *props, int *cold) drivers/media/dvb/dvb-usb/dvb-usb-init.c:230: if ((desc = dvb_usb_find_device(udev,props,&cold)) == NULL) { drivers/usb/core/usb.c:630: * usb_find_device - find a specific usb device in the system drivers/usb/core/usb.c:642:struct usb_device *usb_find_device(u16 vendor_id, u16 product_id) Signed-off-by:Ming Lei <tom.leiming@gmail.com> Signed-off-by:
-
Michal Nazarewicz authored
In to places in fsg_common_init() an unconditional call to kfree() on common was performed in error recovery which is not a valid behaviour since fsg_common structure is not always allocated by fsg_common_init(). To fix, the calls has been replaced with a goto to a proper error recovery which does the correct thing. Also, refactored fsg_common_release() function. Signed-off-by:
Michal Nazarewicz <mina86@mina86.com> Reviewed-by:
Viral Mehta <viral.mehta@lntinfotech.com> Signed-off-by:
-
Ming Lei authored
Obviously, {} is needed in the branch of "else if (hcd->driver->flags & HCD_LOCAL_MEM)" for handling of setup packet mapping. Signed-off-by: -
Anand Gadiyar authored
An undocumented "feature" in the OMAP3 EHCI controller causes suspended ports to be taken out of suspend when the USBCMD.Run/Stop bit is cleared (this bit is normally cleared when ehci_bus_suspend is called). This "feature" breaks suspend-resume if the root-hub is allowed to suspend. (The controller thinks it is in resume, and the PHY thinks it is still in suspend). There is an undocumented register bit that can be used to disable this feature and restore normal behavior. Set this bit so suspend-resume can work normally. Tested on OMAP3 SDPs with the NXP ISP1504 and NXP ISP1703 PHYs. Signed-off-by:
Anand Gadiyar <gadiyar@ti.com> Signed-off-by:
-
Alan Stern authored
This patch (as1379) reworks the logic for handling USB interface runtime-PM settings -- hopefully it's right this time! The problem is that when a driver is unbound or binding fails, runtime PM for the interface always gets disabled. But pm_runtime_disable() nests, so it shouldn't be called unless the interface was previously enabled for runtime PM. Signed-off-by:
Rob Duncan <Robert.Duncan@exar.com> Tested-by:
-
Andiry Xu authored
Macro TRB_TYPE is misused in some places. Fix the wrong usage. Signed-off-by:
Andiry Xu <andiry.xu@amd.com> Cc: stable <stable@kernel.org> Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
John Youn authored
Change transfer ring behavior to not follow/activate link TRBs until active TRBs are queued after it. This change affects the behavior when a TD ends just before a link TRB. Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
-
Randy Dunlap authored
Fix g_ffs build error, add a needed header file: drivers/usb/gadget/f_fs.c:1064:error: 'PAGE_CACHE_SIZE' undeclared (first use in this function) drivers/usb/gadget/f_fs.c:1065:error: 'PAGE_CACHE_SHIFT' undeclared (first use in this function) Signed-off-by:
-
Anand Gadiyar authored
On OMAP systems, we have two different OHCI controllers. The legacy one is present in OMAP1/2 chips, and the newer one comes bundled as a companion to the EHCI controller on OMAP3 and newer chips. We may have multi-omap configurations where OMAP2 and OMAP3 support may be enabled in the same kernel, and need a mechanism to keep both drivers around. This patch adds a Kconfig entry for each of these drivers. Signed-off-by:
-
Anand Gadiyar authored
Add support for the OHCI controller present in OMAP3 and newer chips. The code is mostly based off the ehci-omap.c driver. Some of it is common to both drivers and will eventually need to be factored out to platform init files. In its current state, the driver cannot co-exist with the ehci-omap driver, and this will be fixed in later versions. The second driver to be loaded will overwrite settings made by the other. For now, this driver should allow the few users of OMAP3 OHCI to get going. Signed-off-by:
-
Anand Gadiyar authored
Add platform init code for the OMAP3 OHCI driver. Also, configure padconf settings for OMAP3 depending on which port mode is used. Signed-off-by:
-
Dinh Nguyen authored
renamed fsl_mx3_udc.c -> fsl_mxc_udc.c for mx51, usb core is clocked from sources that are not 60mhz. Signed-off-by:
Dinh Nguyen <Dinh.Nguyen@freescale.com> Signed-off-by:
-
Johan Hovold authored
Reverse priority of errors reported to ldisc so that it matches that of other serial drivers (break takes precedence over parity, which takes precedence over framing errors). Also make sure overrun errors are handled as in other drivers, that is, an overrun error is always reported and is not associated with any received character (instead a NULL character with the TTY_OVERRUN flag set is inserted). Signed-off-by:
-
Johan Hovold authored
Use tty_insert_flip_string_fixed_flag to report errors to line discipline. Signed-off-by:
-
Johan Hovold authored
Use tty_insert_flip_string_fixed_flag to report errors to line discipline. Signed-off-by:
-
Anton Vorontsov authored
There were some reports[1] of isp1760 USB driver malfunctioning with high speed devices, noticed on Blackfin and PowerPC targets. These reports indicated that the original Philips 'pehcd'[2] driver worked fine. We've noticed the same issue with an ARM RealView platform. This happens under load (with only some mass storage devices, not all, just as in another report[3]): error bit is set in DW3 error bit is set in DW3 error bit is set in DW3 usb 1-1.2: device descriptor read/64, error -32 It appears that the 'pehcd' driver checks the X bit only if the transaction is halted (H bit), otherwise the error is so far insignificant. The ISP176x chips were modeled after EHCI, and EHCI spec says (thanks to Alan Stern for pointing out): "Transaction errors cause the status field to be updated to reflect the type of error, but the transaction continues to be retried until the Active bit is set to 0. When the error counter reaches 0, the Halt bit is set and the Active bit is cleared." So, just as the original Philips driver, isp1760 must report the error only if the transaction error and the halt bits are set. [1] http://markmail.org/message/lx4qrlbrs2uhcnly [2] svn co svn://sources.blackfin.uclinux.org/linux-kernel/trunk/drivers/usb/host -r 5494 See pehci.c:pehci_hcd_update_error_status(). [3] http://blackfin.uclinux.org/gf/tracker/5148Signed-off-by:
Anton Vorontsov <avorontsov@mvista.com> Acked-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Andiry Xu authored
When USB3 protocol port detects an USB3.0 device attach, the port will automatically transition to the Enabled state upon the completion of successful link training. Do not disable USB3 protocol ports in hub_activate(), or USB3.0 device will fail to be recognized if xHCI bus power management is implemented. Signed-off-by:
-
Johan Hovold authored
Use process_read_urb to implement read processing. Compile-only tested. Signed-off-by:
Bart Hartgers <bart.hartgers@gmail.com> Signed-off-by:
-
Johan Hovold authored
Fix regression introduced by commit a108bfcb (USB: tty: Prune uses of tty_request_room in the USB layer) which broke three drivers (cypress_m8, digi_acceleport and spcp8x5) through incorrect use of tty_insert_flip_string_fixed_flag. Signed-off-by:
-
Robert Lukassen authored
This is a patch that makes sure that the device ID data (idVendor, idProduct and bcdDevice) are assigned to the descriptor in the cdev structure *before* the composite gadget starts binding. This allows the composite driver, and all the composite functions it uses, access to that data. In one of the composite functions we created, we needed to register an input device and wanted to use the idVendor, idProduct and bcdDevice codes to properly initialize the id field of the input device. We could not do that because the idVendor, idProduct and bcdDevice values were only set in the cdec structure *after* the composite->bind(cdev) call. Signed-off-by:
Robert Lukassen <robert.lukassen@tomtom.com> Signed-off-by:
-
Randy Dunlap authored
Fix gcc warning on mixed declarations/code: drivers/usb/host/u132-hcd.c:1450: warning: ISO C90 forbids mixed declarations and code Signed-off-by:
-
Sarah Sharp authored
After using state stored in xhci_virt_ep to clean up a stalled endpoint, be sure to set the stalled stream ID back to 0. Signed-off-by:
-
Michal Nazarewicz authored
The FunctionFS gadget may provide the source/sink interface not as the first interface (with id == 0) but some different interface hence a code to find the interface number is required. (Note that you will still configure the gadget to report idProduct == 0xa4a4 (an "echo 0xa4a4 >/sys/module/g_ffs/parameters/usb_product" should suffice) or configure host to handle 0x0525:0xa4ac devices using the usbtest driver.) Signed-off-by:
-
David Brownell authored
The testusb program just issues ioctls to perform the tests implemented by the kernel driver. It can generate a variety of transfer patterns; you should make sure to test both regular streaming and mixes of transfer sizes (including short transfers). For more information on how this can be used and on USB testing refer to <URL:http://www.linux-usb.org/usbtest/>. Signed-off-by:
-
Michal Nazarewicz authored
This adds an example user-space FunctionFS driver which implements a source/sink interface used for testing. Signed-off-by:
-
Michal Nazarewicz authored
The Function Filesystem (FunctioFS) lets one create USB composite functions in user space in the same way as GadgetFS lets one create USB gadgets in user space. This allows creation of composite gadgets such that some of the functions are implemented in kernel space (for instance Ethernet, serial or mass storage) and other are implemented in user space. Signed-off-by:
-
Michal Nazarewicz authored
The FunctionFS is a USB composite function that can be used with the composite framework to create an USB gadget. >From kernel point of view it is just a composite function with some unique behaviour. It may be added to an USB configuration only after the user space driver has registered by writing descriptors and strings (the user space program has to provide the same information that kernel level composite functions provide when they are added to the configuration). >From user space point of view it is a file system which when mounted provide an "ep0" file. User space driver need to write descriptors and strings to that file. It does not need to worry about endpoints, interfaces or strings numbers but simply provide descriptors such as if the function was the only one (endpoints and strings numbers starting from one and interface numbers starting from core). The FunctionFS changes numbers of those as needed also handling situation when numbers differ in different configurations. When descriptors and strings are written "ep#" files appear (one for each declared endpoint) which handle communication on a single endpoint. Again, FunctionFS takes care of the real numbers and changing of the configuration (which means that "ep1" file may be really mapped to (say) endpoint 3 (and when configuration changes to (say) endpoint 2)). "ep0" is used for receiving events and handling setup requests. When all files are closed the function disables itself. Signed-off-by:
-
Michal Nazarewicz authored
__init, __initdata and __exit tags have have been removed from various files to make it possible for gadgets that do not use the __init/__exit tags to use those. Files in question are related to: * the core composite framework, * the mass storage function (fixing a section mismatch) and * ethernet driver (ACM, ECM, RNDIS). Signed-off-by:
-
Michal Nazarewicz authored
This patch modifies the fs/timerfd.c to use the newly created wait_event_interruptible_locked_irq() macro. This replaces an open code implementation with a single macro call. Signed-off-by:
-
Michal Nazarewicz authored
New wait_event_interruptible{,_exclusive}_locked{,_irq} macros added. They work just like versions without _locked* suffix but require the wait queue's lock to be held. Also __wake_up_locked() is now exported as to pair it with the above macros. The use case of this new facility is when one uses wait queue's lock to protect a data structure. This may be advantageous if the structure needs to be protected by a spinlock anyway. In particular, with additional spinlock the following code has to be used to wait for a condition: spin_lock(&data.lock); ... for (ret = 0; !ret && !(condition); ) { spin_unlock(&data.lock); ret = wait_event_interruptible(data.wqh, (condition)); spin_lock(&data.lock); } ... spin_unlock(&data.lock); This looks bizarre plus wait_event_interruptible() locks the wait queue's lock anyway so there is a unlock+lock sequence where it could be avoided. To avoid those problems and benefit from wait queue's lock, a code similar to the following should be used: /* Waiting */ spin_lock(&data.wqh.lock); ... ret = wait_event_interruptible_locked(data.wqh, (condition)); ... spin_unlock(&data.wqh.lock); /* Waiting exclusively */ spin_lock(&data.whq.lock); ... ret = wait_event_interruptible_exclusive_locked(data.whq, (condition)); ... spin_unlock(&data.whq.lock); /* Waking up */ spin_lock(&data.wqh.lock); ... wake_up_locked(&data.wqh); ... spin_unlock(&data.wqh.lock); When spin_lock_irq() is used matching versions of macros need to be used (*_locked_irq()). Signed-off-by:
-
