- 21 Jun, 2016 40 commits
-
-
Ido Schimmel authored
Not all vPorts will have FIDs assigned to them, so make sure functions first test for FID presence. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
As previously explained, not all vPorts will be assigned FIDs, so instead of returning the FID index of a vPort, return a pointer to its FID struct. This will allow us to know whether it's legal to access the vPort's FID parameters such as index and device. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
When L3 interfaces will be introduced a vPort won't necessarily have a FID assigned to it. This can happen if it's not member in a bridge (in which case it's assigned a vFID) or doesn't have an IP address (in which case it's assigned an rFID). Therefore, instead check the VID parameter to test whether a port is a vPort or not. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
In a very similar way to the vFIDs, make the first 4K FIDs - used in the VLAN-aware bridge - use the new FID struct. Upon first use of the FID by any of the ports do the following: 1) Create the FID 2) Setup a matching flooding entry 3) Create a mapping for the FID Unlike vFIDs, upon creation of a FID we always create a global VID-to-FID mapping, so that ports without upper vPorts can use it instead of creating an explicit {Port, VID} to FID mapping. When a port leaves a FID the reverse is performed. Whenever the FID's reference count reaches zero the FID is deleted along with the global mapping. The per-FID struct will later allow us to configure L3 interfaces on top of the VLAN-aware bridge. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
When a vPort is created or when it joins a bridge we always do the same set of operations: 1) Create the vFID, if not already created 2) Setup flooding for the vFID 3) Map the {Port, VID} to the vFID When a vPort is destroyed or when it leaves a bridge the reverse is performed. Encapsulate the above in join / leave functions and simplify the code. FIDs and rFIDs will use a similar set of functions. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Up until now we had a dedicated struct only for vFIDs, but before introducing support for L3 interfaces we need to make it generic and use it for all three types of FIDs: 1) FIDs - 0..4K-1, used for the VLAN-aware bridge 2) vFIDs - 4K..15K-1, used for VLAN-unaware bridges 3) rFIDs - 15K..16K-1, used to direct traffic to / from the router in the device. Will be introduced later in the series. The three types of L3 interfaces - Router InterFaces, RIFs - that will be introduced correspond to the three types of FIDs and are configured using them. Therefore, we'll need to store the links between them as well as a reference count on the underlying FID, so that the corresponding RIF will be destroyed when it reaches zero. Note that the lower 0.5K vFIDs are currently used for for non-bridged netdevs, so that traffic could be flooded to the CPU port. However, when rFIDs will be introduced we'll no longer need these and they too will be used for VLAN-unaware bridges. Make the vFID struct generic by renaming it and some of its fields. FIDs will be converted to use it later in the series. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Use a FID index instead of vFID and ease the transition towards a generic FID struct. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
A FID used by a vPort (vFID, but also rFID later in the series) is always mapped using {Port, VID} and not only VID as with the 4K FIDs of the VLAN-aware bridge. Instead of specifying all the arguments each time, just wrap this operation using a dedicated function and simplify the code. As before, the function takes FID as its argument in preparation for a generic FID struct. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Simplify the code and use only one function for vFID creation / destruction. Unlike before, the function receives a FID index as its argument and not a vFID index. Instead of passing 0, now one would need to pass 4K, which is the first vFID. This is the first step in creating a generic FID struct that will be used for all three types of FIDs. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
In all call sites 'only_uc' is set to false, so strip it. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
There is a macro to do this kind of declarations, so use it. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
We hold a reference count on the number of ports member in the VLAN-aware bridge, as we only support one. Instead of always incrementing / decrementing the reference count after joining / leaving the bridge, simply do this accounting in the join / leave functions. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
The argument 'br_dev' is never used, so remove it. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
When responding to unlinking CHANGEUPPER notifications we shouldn't return any value, as it's not checked by upper layers. In addition, there's nothing the driver can do in case of failure, so it should simply continue and try to free as much resources as possible and not stop on first error. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Instead of checking for a condition and then issue the warning, just do it in one go and simplify the code. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
When upper device of a VLAN device changes we already made sure it's a bridge device in PRECHANGEUPPER, so no need to check it's a master device in CHANGEUPPER. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
When a port netdev is put under LAG it cannot have VLAN upper devices, so forbid that. The LAG device itself can have VLAN upper devices. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
We currently only support the following upper devices for port netdevs: 1) Bridge 2) LAG (bond / team) 3) VLAN Any other device is forbidden, so return an error. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Instead of checking the error value and returning NOTIFY_BAD, just use notifier_from_errno() and simplify the code. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Yisen Zhuang says: ==================== net: hns: fix some bugs in hns driver This series includes some bugs fixed. All these patches needs to be applied after the patchset about ACPI support, so this series is floated to net-next list. The patches are: > from Daode, fixes about pfc pause frame, getting coaslesce, led control logic, TSO on|off and tcam table configuration. > from Jun He, fix the potential leak to port unavailable > from Kejian, fix bug of loopback and failing to test ping6 > from Qianqian, fix the several typo in hns driver For more details, please see individual patches. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Daode Huang authored
When enable/disable tso, the driver tries to access the hardware register, but this operation will cause the port unavalible when there is traffic. This patch tries to enable TSO when initialize, then control tso through TSE bit in transmit descriptor. Signed-off-by:
Daode Huang <huangdaode@hisilicon.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Daode Huang authored
The default coalesce timeout is 3us, which is will cause CPU usage is too high. This patch change it to 50us in order to reduce CPU usage and the value makes sure network latency also meets requirement. Signed-off-by:
Daode Huang <huangdaode@hisilicon.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Daode Huang authored
The default sbm config parameter leaves little buffer when there is heavy traffic, which will cause packets drop. This patch changes them to make enough buffers for handling packets. Signed-off-by:
Daode Huang <huangdaode@hisilicon.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jun He authored
When hns_nic_poll_rx_skb alloc skb fail, it will break receive cycle and read new fbd_num to start new receive cycle. It recomputes cycle num is fbd_num minus clean_count, actually this cycle num is too big because it drop out receive cycle. It brings about the port unavailable. So we will goto out when alloc skb fail to fix this bug. Signed-off-by:
Jun He <hjat2005@huawei.com> Signed-off-by:
Ding Tianhong <dingtianhong@huawei.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Daode Huang authored
The default driver sets anchor led bit to 0 when link down, actually, the anchor bit should be set to 1, so fixes it when link status is down. Secondly, change the return value of cpld_set_led_id to 0, which means leave the cpld to control led blink frequece other than the driver itself. Signed-off-by:
Daode Huang <huangdaode@hisilicon.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Daode Huang authored
When network interface is enabled, the ring enable operation is conducted twice. This patch deletes the redundancy code of ring enable, and integrates hnae_ae_ops.toggle_queue_status other functions to hns_ae_start. Signed-off-by:
Daode Huang <huangdaode@hisilicon.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Daode Huang authored
This patch adds get_coalesce_range api for hns, it shows range of coalesce usecs and frames that can be set on this interface. Signed-off-by:
Daode Huang <huangdaode@hisilicon.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Daode Huang authored
The current driver stores the high bit value of tcam data register to the tcam data low element, stores the low bit value of tcam data register to tcam data high element, this patch fixes this bug. Signed-off-by:
Daode Huang <huangdaode@hisilicon.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Daode Huang authored
This patch adds spin lock for tcam table operation, there maybe a race condition happens when more than one thread try to change the tcam talbe entries. Signed-off-by:
Daode Huang <huangdaode@hisilicon.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Daode Huang authored
For SoC hip06, PFC pause handled in dsaf, while hip05 in XGMAC, so change the statistics of pfc pause in dsaf and remove the old pfc pause frame statistics. Signed-off-by:
Daode Huang <huangdaode@hisilicon.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Qianqian Xie authored
For debug-ports,there are two non-synchronized processes: Speed-Auto-Negotiation and Link-Update-Status. The two processes are towed by two different state machines. Bond reads the speed when link up, but the speed maybe not update the right value at that time.That make for bond's wrong speed. Thus only one state machine should be used and if phy_state_machine is used, it does not need to do hns_nic_update_link_status(). Signed-off-by:
Qianqian Xie <xieqianqian@huawei.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kejian Yan authored
When run ethtool cmd(ethtool -t ethx) again and again for a long time, it will be probabilistically fail. The PHYs' registers may be on different pages, so it must be switch to the right page before setting PHYs' registers. And __lb_up() calls phy_start() to startup the PHYs device, but this function may change Copper Control Register(Page 0, Register 0) to an other value. It would cause phy loopback test fail. if we remove phy_start(), we have to remove the relative phy_stop(), phy_disconnect() when doing phy loopback to keep the phy stay in right status. Reported-by:
hejun <hjat2005@huawei.com> Signed-off-by:
Kejian Yan <yankejian@huawei.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kejian Yan authored
As Hilink3 and Hilink4 use the same xge training and xge u adaptor for HNSv2, it needs to select which Hilink to be set before relative serdes being configed. The hilink_access_sel is the register to do that. Signed-off-by:
Kejian Yan <yankejian@huawei.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Qianqian Xie authored
The error info should be printed as "set mask to 64bit fail!" instead of "set mask to 32bit fail!" in dma_set_mask_and_coherent(). Signed-off-by:
Qianqian Xie <xieqianqian@huawei.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Qianqian Xie authored
The driver uses devm_ioremap_resource, it will unmap the map automatically, remove the unnecessary the resource free. Signed-off-by:
Qianqian Xie <xieqianqian@huawei.com> Reported-by:
Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Qianqian Xie authored
The annotation info for hns_nic_reset_subtask() should be "for resetting subtask" instead of "for resetting suntask". Signed-off-by:
Qianqian Xie <xieqianqian@huawei.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kejian Yan authored
HNS receives a packet without doing anything, but it should call skb_reset_mac_header() to initialize the header before using eth_hdr(). Fixes: 0d6b425aSigned-off-by:
Kejian Yan <yankejian@huawei.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Qianqian Xie authored
For service port, hns dsaf v1 support to close tx_pause. However, the port will be invalid when it run command ethtool to close tx_pause. This patch will fix it. Signed-off-by:
Qianqian Xie <xieqiaqian@huawei.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Qianqian Xie authored
The bit fileds of PPE reset register are different between HNS v1 and HNS v2, but the current procedure just only match HNS v1. Here is a patch to fix it. Signed-off-by:
Kejian Yan <yankejian@huawei.com> Signed-off-by:
Qianqian Xie <xieqianqian@huawei.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-