It's not needed anymore.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4 currently uses a too high tx coalescing setting, deferring
TX completion interrupts by up to 128 us.

With the recent skb_orphan() removal in commit 8112ec3b,
performance of a single TCP flow is capped to ~4 Gbps, unless
we increase tcp_limit_output_bytes.

I suggest using 16 us instead of 128 us, allowing a finer control.

Performance of a single TCP flow is restored to previous levels,
while keeping TCP small queues fully enabled with default sysctl.

This patch is also a BQL prereq.
Reported-by: Vimalkumar <j.vimal@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch gets the runtime PM reference count before calling
usbnet_{read|write}_cmd, and puts it after completion of the
usbnet_{read|write}_cmd, so that the usb control message can always
be sent to one active device in the non-PM context.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch applies the introduced usbnet_read_cmd_nopm() and
usbnet_write_cmd_nopm() in the callback of resume and suspend
to avoid deadlock if USB runtime PM is considered into
usbnet_read_cmd() and usbnet_write_cmd().

Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes memory leak in smsc95xx_suspend.

Also, it isn't necessary to bother mm to allocate 8bytes/16byte,
and we can use stack variable safely.
Acked-By: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch applies the introduced usbnet_read_cmd_nopm() and
usbnet_write_cmd_nopm() in the callback of resume and suspend
to avoid deadlock if USB runtime PM is considered into
usbnet_read_cmd() and usbnet_write_cmd().

Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces the below two helpers to prepare for solving
the usbnet runtime PM problem, which may cause some network utilities
(ifconfig, ethtool,...) touch a suspended device.

	usbnet_read_cmd_nopm()
	usbnet_write_cmd_nopm()

The above two helpers should be called by usbnet resume/suspend
callback to avoid deadlock.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On gcc 4.7, we will get alignment traps in the ip stack if we don't align
the ip headers on receive. The h/w can support this, so use ip aligned
allocations.

Cut down the unnecessary padding on the allocation. The buffer can start on
any byte alignment, but the size including the begining offset must be 8
byte aligned. So the h/w buffer size must include the NET_IP_ALIGN offset.

Thanks to Eric Dumazet for the initial patch highlighting the padding issues.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only generate tx interrupts on every ring size / 4 descriptors. Move the
netif_stop_queue call to the end of the xmit function rather than
checking at the beginning.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The interrupts have already been cleared, so we don't need to clear them
again. Also, we could miss interrupts if they are cleared, but we don't
process the packet.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The standard readl/writel accessors involve a spinlock and cache sync
operation on ARM platforms with an outer cache. Only DMA triggering
accesses need this, so use the raw variants instead in the critical paths.

The relaxed variants would be more appropriate, but don't exist on all
arches.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New received frames will trigger the rx DMA to poll the DMA descriptors,
so there is no need to tell the h/w to poll. We also want to enable
dropping frames from the fifo when there is no buffer.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable the tx dma to start reading the next frame while sending the current
frame.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 56b765b7 (htb: improved accuracy at high rates)
introduced two bugs :

1) one bstats_update() was inadvertently removed from
   htb_dequeue_tree(), breaking statistics/rate estimation.

2) Missing qdisc_put_rtab() calls in htb_change_class(),
   leaking kernel memory, now struct htb_class no longer
   retains pointers to qdisc_rate_table structs.

   Since only rate is used, dont use qdisc_get_rtab() calls
   copying data we ignore anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vimalkumar <j.vimal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

instead of making separate tg3_napi_disable() and netif_tx_disable() calls.

Update version to 3.126.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for 5717C0 which is a 5720A0 with special bonds-out option.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed some coding style issues.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

checkpatch.pl throws error message for the current code. This patch fixes
this coding style issue.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: Jitendra Kalsaria <Jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is a follow-up for patch "net: filter: add vlan tag access"
to support the new VLAN_TAG/VLAN_TAG_PRESENT accessors in BPF JIT.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following chips need to enable internal settings to let ASPM
and clock request work.

RTL8111E-VL, RTL8111F, RTL8411, RTL8111G
RTL8105, RTL8402, RTL8106
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of issuing (0) statements when !CONFIG_SYSFS which will cause
'warning: ', we'll use inline statements instead. This will effectively
do the same thing, but suppress any unnecessary warnings.

Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: bridge@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use WARN rather than printk followed by WARN_ON(1), for conciseness.

A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression list es;
@@

-printk(
+WARN(1,
  es);
-WARN_ON(1);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Building atp.o triggers this GCC warning:
    drivers/net/ethernet/realtek/atp.c: In function ‘set_rx_mode’:
    drivers/net/ethernet/realtek/atp.c:871:26: warning: ‘mc_filter[0]’ may be used uninitialized in this function [-Wuninitialized]

GCC is correct. In promiscuous mode 'mc_filter' will be used
uninitialized in set_rx_mode_8012(), which is apparently inlined into
set_rx_mode().

But it turns out set_rx_mode_8012() will never be called, since
net_local.chip_type will always be RTL8002. So we can just remove
set_rx_mode_8012() and do some related cleanups.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

The CPSW driver remaps two different IO regions, but fails to unmap them
both. This patch fixes the issue by calling iounmap in the appropriate
places.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code mixes up the CPSW_SS and the CPSW_WR register naming. This patch
changes the names to conform to the published Technical Reference Manual
from TI, in order to make working on the code less confusing.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bridge notify hook rtnl_bridge_notify() was not handling the
case where the master flags was set or with both flags set. First
flags are not being passed correctly and second the logic to parse
them is broken.

This patch passes the original flags value and fixes the
logic.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When underlying phy driver restores its state very fast after being brought
down and up so that macb driver function macb_handle_link_change() was never
called with link state "down", driver's internal representation of phy speed
and duplex (bp->speed and bp->duplex) didn't change. So, macb driver sees no
reason to perform actual write to the NCFGR register, although the speed and
duplex settings in that register were reset when interface was brought down
and up. In that case actual phy speed and duplex differ from NCFGR settings.
The patch fixes that by keeping internal driver representation of speed and
duplex in sync with actual content of NCFGR.
Signed-off-by: Vitalii Demianets <vitas@nppfactor.kiev.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings recently came up with a better way to handle the kconfig
dependencies for the PTP hardware clocks. This patch converts one new and
one older driver to the new scheme.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current HTB (and TBF) uses rate table computed by the "tc"
userspace program, which has the following issue:

The rate table has 256 entries to map packet lengths
to token (time units).  With TSO sized packets, the
256 entry granularity leads to loss/gain of rate,
making the token bucket inaccurate.

Thus, instead of relying on rate table, this patch
explicitly computes the time and accounts for packet
transmission times with nanosecond granularity.

This greatly improves accuracy of HTB with a wide
range of packet sizes.

Example:

tc qdisc add dev $dev root handle 1: \
        htb default 1

tc class add dev $dev classid 1:1 parent 1: \
        rate 5Gbit mtu 64k

Here is an example of inaccuracy:

$ iperf -c host -t 10 -i 1

With old htb:
eth4:   34.76 Mb/s In  5827.98 Mb/s Out -  65836.0 p/s In  481273.0 p/s Out
[SUM]  9.0-10.0 sec   669 MBytes  5.61 Gbits/sec
[SUM]  0.0-10.0 sec  6.50 GBytes  5.58 Gbits/sec

With new htb:
eth4:   28.36 Mb/s In  5208.06 Mb/s Out -  53704.0 p/s In  430076.0 p/s Out
[SUM]  9.0-10.0 sec   594 MBytes  4.98 Gbits/sec
[SUM]  0.0-10.0 sec  5.80 GBytes  4.98 Gbits/sec

The bits per second on the wire is still 5200Mb/s with new HTB
because qdisc accounts for packet length using skb->len, which
is smaller than total bytes on the wire if GSO is used.  But
that is for another patch regardless of how time is accounted.

Many thanks to Eric Dumazet for review and feedback.
Signed-off-by: Vimalkumar <j.vimal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"ip link add ... type vxlan ... ttl X" allows a user to set the TTL
used by a VXLAN for encapsulation. The provided value was ignored by
vxlan module and the default value of 1 was used when encapsulating
multicast packets.
Signed-off-by: Vincent Bernat <bernat@luffy.cx>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for wol wakeup on unicast, broadcast,
multicast and arp frames.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Ethertype 0x4305 (not an officially registered id).
This Ethertype is used by every frame generated by B.A.T.M.A.N.-Advanced. Its
definition is currently batman-adv local only and since it is not officially
registered it is better to make its definition kernel-wide so that we avoid
collisions given by future unofficial uses of the same Ethertype.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

After d58d46b5 (r8169: jumbo fixes.) max frame len is stored in
rtl_chip_infos[].jumbo_max for each chip and SafeMtu should be gone.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

As suggested by Eric, we could introduce a helper function
for ipv6 too, to avoid checking if rt is NULL before
dst_release().

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can save a test in ip_rt_put(), considering dst_release() accepts
a NULL parameter, and dst is first element in rtable.

Add a BUILD_BUG_ON() to catch any change that could break this
assertion.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <amwang@redhat.com>
Acked-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lots of points in the sctp_cmd_interpreter function treat the sctp_cmd_t arg as
a void pointer, even though they are written as various other types.  Theres no
need for this as doing so just leads to possible type-punning issues that could
cause crashes, and if we remain type-consistent we can actually just remove the
void * member of the union entirely.

Change Notes:

v2)
	* Dropped chunk that modified SCTP_NULL to create a marker pattern
	 should anyone try to use a SCTP_NULL() assigned sctp_arg_t, Assigning
	 to .zero provides the same effect and should be faster, per Vlad Y.

v3)
	* Reverted part of V2, opting to use memset instead of .zero, so that
	 the entire union is initalized thus avoiding the i164 speculative load
	 problems previously encountered, per Dave M..  Also rewrote
	 SCTP_[NO]FORCE so as to use common infrastructure a little more

Signed-off-by: Neil Horman <nhorman@tuxdriver.com
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-sctp@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>