- 24 Mar, 2019 3 commits
-
-
Soheil Hassas Yeganeh authored
Add documentation to the tcp_ca_state enum, since this enum is exposed in uapi. Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Cc: Sowmini Varadhan <sowmini05@gmail.com> Acked-by:
Sowmini Varadhan <sowmini05@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
tcp_clock_ns() (aka ktime_get_ns()) is using monotonic clock, so the checks we had in tcp_mstamp_refresh() are no longer relevant. This patch removes cpu stall (when the cache line is not hot) Signed-off-by:
-
Florian Fainelli authored
The tristate prompt should have been replaced rather than defined a few lines below, rebase mistake. Fixes: 17cc9821 ("net: phy: Move Omega PHY entry to Cygnus PHY driver") Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
- 22 Mar, 2019 3 commits
-
-
Johannes Berg authored
Since maxattr is common, the policy can't really differ sanely, so make it common as well. The only user that did in fact manage to make a non-common policy is taskstats, which has to be really careful about it (since it's still using a common maxattr!). This is no longer supported, but we can fake it using pre_doit. This reduces the size of e.g. nl80211.o (which has lots of commands): text data bss dec hex filename 398745 14323 2240 415308 6564c net/wireless/nl80211.o (before) 397913 14331 2240 414484 65314 net/wireless/nl80211.o (after) -------------------------------- -832 +8 0 -824 Which is obviously just 8 bytes for each command, and an added 8 bytes for the new policy pointer. I'm not sure why the ops list is counted as .text though. Most of the code transformations were done using the following spatch: @ops@ identifier OPS; expression POLICY; @@ struct genl_ops OPS[] = { ..., { - .policy = POLICY, }, ... }; @@ identifier ops.OPS; expression ops.POLICY; identifier fam; expression M; @@ struct genl_family fam = { .ops = OPS, .maxattr = M, + .policy = POLICY, ... }; This also gets rid of devlink_nl_cmd_region_read_dumpit() accessing the cb->data as ops, which we want to change in a later genl patch. Signed-off-by:Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Heiner Kallweit authored
Replace the call to netif_wake_queue in rtl8169_start_xmit with netif_start_queue as we don't need to actually wake up the queue since we are still in mid transmit so we just need to reset the bit so it doesn't prevent the next transmit. (Description shamelessly copied from a mail sent by Alex.) Suggested-by:
Alexander Duyck <alexander.h.duyck@linux.intel.com> Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
Aquantia PHY's of the AQR107 family support the downshift feature. Add support for it as standard PHY tunable so that it can be controlled via ethtool. The AQCS109 supports a proprietary 2-pair 1Gbps mode. If two such PHY's are connected to each other with a 2-pair cable, they may not be able to establish a link if both advertise modes > 1Gbps. v2: - add downshift event detection - warn if downshift occurred - read downshifted rate from vendor register - enable downshift per default on all AQR107 family members Signed-off-by:
-
- 21 Mar, 2019 34 commits
-
-
David S. Miller authored
Vlad Buslov says: ==================== Refactor flower classifier to remove dependency on rtnl lock Currently, all netlink protocol handlers for updating rules, actions and qdiscs are protected with single global rtnl lock which removes any possibility for parallelism. This patch set is a third step to remove rtnl lock dependency from TC rules update path. Recently, new rtnl registration flag RTNL_FLAG_DOIT_UNLOCKED was added. TC rule update handlers (RTM_NEWTFILTER, RTM_DELTFILTER, etc.) are already registered with this flag and only take rtnl lock when qdisc or classifier requires it. Classifiers can indicate that their ops callbacks don't require caller to hold rtnl lock by setting the TCF_PROTO_OPS_DOIT_UNLOCKED flag. The goal of this change is to refactor flower classifier to support unlocked execution and register it with unlocked flag. This patch set implements following changes to make flower classifier concurrency-safe: - Implement reference counting for individual filters. Change fl_get to take reference to filter. Implement tp->ops->put callback that was introduced in cls API patch set to release reference to flower filter. - Use tp->lock spinlock to protect internal classifier data structures from concurrent modification. - Handle concurrent tcf proto deletion by returning EAGAIN, which will cause cls API to retry and create new proto instance or return error to the user (depending on message type). - Handle concurrent insertion of filter with same priority and handle by returning EAGAIN, which will cause cls API to lookup filter again and process it accordingly to netlink message flags. - Extend flower mask with reference counting and protect masks list with masks_lock spinlock. - Prevent concurrent mask insertion by inserting temporary value to masks hash table. This is necessary because mask initialization is a sleeping operation and cannot be done while holding tp->lock. Both chain level and classifier level conflicts are resolved by returning -EAGAIN to cls API that results restart of whole operation. This retry mechanism is a result of fine-grained locking approach used in this and previous changes in series and is necessary to allow concurrent updates on same chain instance. Alternative approach would be to lock the whole chain while updating filters on any of child tp's, adding and removing classifier instances from the chain. However, since most CPU-intensive parts of filter update code are specifically in classifier code and its dependencies (extensions and hw offloads), such approach would negate most of the gains introduced by this change and previous changes in the series when updating same chain instance. Tcf hw offloads API is not changed by this patch set and still requires caller to hold rtnl lock. Refactored flower classifier tracks rtnl lock state by means of 'rtnl_held' flag provided by cls API and obtains the lock before calling hw offloads. Following patch set will lift this restriction and refactor cls hw offloads API to support unlocked execution. With these changes flower classifier is safely registered with TCF_PROTO_OPS_DOIT_UNLOCKED flag in last patch. Changes from V2 to V3: - Rebase on latest net-next Changes from V1 to V2: - Extend cover letter with explanation about retry mechanism. - Rebase on current net-next. - Patch 1: - Use rcu_dereference_raw() for tp->root dereference. - Update comment in fl_head_dereference(). - Patch 2: - Remove redundant check in fl_change error handling code. - Add empty line between error check and new handle assignment. - Patch 3: - Refactor loop in fl_get_next_filter() to improve readability. - Patch 4: - Refactor __fl_delete() to improve readability. - Patch 6: - Fix comment in fl_check_assign_mask(). - Patch 9: - Extend commit message. - Fix error code in comment. - Patch 11: - Fix fl_hw_replace_filter() to always release rtnl lock in error handlers. - Patch 12: - Don't take rtnl lock before calling __fl_destroy_filter() in workqueue context. - Extend commit message with explanation why flower still takes rtnl lock before calling hardware offloads API. Github: <https://github.com/vbuslov/linux/tree/unlocked-flower-cong3> ==================== Signed-off-by: -
Vlad Buslov authored
Set TCF_PROTO_OPS_DOIT_UNLOCKED for flower classifier to indicate that its ops callbacks don't require caller to hold rtnl lock. Don't take rtnl lock in fl_destroy_filter_work() that is executed on workqueue instead of being called by cls API and is not affected by setting TCF_PROTO_OPS_DOIT_UNLOCKED. Rtnl mutex is still manually taken by flower classifier before calling hardware offloads API that has not been updated for unlocked execution. Signed-off-by:
Vlad Buslov <vladbu@mellanox.com> Reviewed-by:
Stefano Brivio <sbrivio@redhat.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Vlad Buslov authored
Use 'rtnl_held' flag to track if caller holds rtnl lock. Propagate the flag to internal functions that need to know rtnl lock state. Take rtnl lock before calling tcf APIs that require it (hw offload, bind filter, etc.). Signed-off-by:
-
Vlad Buslov authored
struct tcf_proto was extended with spinlock to be used by classifiers instead of global rtnl lock. Use it to protect shared flower classifier data structures (handle_idr, mask hashtable and list) and fields of individual filters that can be accessed concurrently. This patch set uses tcf_proto->lock as per instance lock that protects all filters on tcf_proto. Signed-off-by:
-
Vlad Buslov authored
Without rtnl lock protection tcf proto can be deleted concurrently. Check tcf proto 'deleting' flag after taking tcf spinlock to verify that no concurrent deletion is in progress. Return EAGAIN error if concurrent deletion detected, which will cause caller to retry and possibly create new instance of tcf proto. Retry mechanism is a result of fine-grained locking approach used in this and previous changes in series and is necessary to allow concurrent updates on same chain instance. Alternative approach would be to lock the whole chain while updating filters on any of child tp's, adding and removing classifier instances from the chain. However, since most CPU-intensive parts of filter update code are specifically in classifier code and its dependencies (extensions and hw offloads), such approach would negate most of the gains introduced by this change and previous changes in the series when updating same chain instance. Signed-off-by:
-
Vlad Buslov authored
Check if user specified a handle and another filter with the same handle was inserted concurrently. Return EAGAIN to retry filter processing (in case it is an overwrite request). Signed-off-by:
-
Vlad Buslov authored
Protect modifications of flower masks list with spinlock to remove dependency on rtnl lock and allow concurrent access. Signed-off-by:
-
Vlad Buslov authored
Without rtnl lock protection masks with same key can be inserted concurrently. Insert temporary mask with reference count zero to masks hashtable. This will cause any concurrent modifications to retry. Wait for rcu grace period to complete after removing temporary mask from masks hashtable to accommodate concurrent readers. Signed-off-by:
-
Vlad Buslov authored
Extend fl_flow_mask structure with reference counter to allow parallel modification without relying on rtnl lock. Use rcu read lock to safely lookup mask and increment reference counter in order to accommodate concurrent deletes. Signed-off-by:
-
Vlad Buslov authored
In order to prevent double deletion of filter by concurrent tasks when rtnl lock is not used for synchronization, add 'deleted' filter field. Check value of this field when modifying filters and return error if concurrent deletion is detected. Refactor __fl_delete() to accept pointer to 'last' boolean as argument, and return error code as function return value instead. This is necessary to signal concurrent filter delete to caller. Signed-off-by:
-
Vlad Buslov authored
Extend flower filters with reference counting in order to remove dependency on rtnl lock in flower ops and allow to modify filters concurrently. Reference to flower filter can be taken/released concurrently as soon as it is marked as 'unlocked' by last patch in this series. Use atomic reference counter type to make concurrent modifications safe. Always take reference to flower filter while working with it: - Modify fl_get() to take reference to filter. - Implement tp->put() callback as fl_put() function to allow cls API to release reference taken by fl_get(). - Modify fl_change() to assume that caller holds reference to fold and take reference to fnew. - Take reference to filter while using it in fl_walk(). Implement helper functions to get/put filter reference counter. Signed-off-by:
-
Vlad Buslov authored
As a preparation for using classifier spinlock instead of relying on external rtnl lock, rearrange code in fl_change. The goal is to group the code which changes classifier state in single block in order to allow following commits in this set to protect it from parallel modification with tp->lock. Data structures that require tp->lock protection are mask hashtable and filters list, and classifier handle_idr. fl_hw_replace_filter() is a sleeping function and cannot be called while holding a spinlock. In order to execute all sequence of changes to shared classifier data structures atomically, call fl_hw_replace_filter() before modifying them. Signed-off-by:
-
Vlad Buslov authored
Flower classifier only changes root pointer during init and destroy. Cls API implements reference counting for tcf_proto, so there is no danger of concurrent access to tp when it is being destroyed, even without protection provided by rtnl lock. Implement new function fl_head_dereference() to dereference tp->root without checking for rtnl lock. Use it in all flower function that obtain head pointer instead of rtnl_dereference(). Signed-off-by:
-
Jakub Kicinski authored
NFP driver ABI contains bits for L2 switching which were never implemented in initially envisioned form. Remove the defines, and open up the possibility of reclaiming the bits for other uses. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by:
-
David S. Miller authored
NeilBrown says: ==================== Two clean-ups for rhashtable. These two patches make small improvements to rhashtable, but are otherwise unrelated. Thanks to Herbert, Miguel, and Paul for the review. ==================== Signed-off-by: -
NeilBrown authored
The pattern set by list.h is that for_each..continue() iterators start at the next entry after the given one, while for_each..from() iterators start at the given entry. The rht_for_each*continue() iterators are documented as though the start at the 'next' entry, but actually start at the given entry, and they are used expecting that behaviour. So fix the documentation and change the names to *from for consistency with list.h Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Acked-by:
Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
NeilBrown authored
rhashtable_try_insert() currently holds a lock on the bucket in the first table, while also locking buckets in subsequent tables. This is unnecessary and looks like a hold-over from some earlier version of the implementation. As insert and remove always lock a bucket in each table in turn, and as insert only inserts in the final table, there cannot be any races that are not covered by simply locking a bucket in each table in turn. When an insert call reaches that last table it can be sure that there is no matchinf entry in any other table as it has searched them all, and insertion never happens anywhere but in the last table. The fact that code tests for the existence of future_tbl while holding a lock on the relevant bucket ensures that two threads inserting the same key will make compatible decisions about which is the "last" table. This simplifies the code and allows the ->rehash field to be discarded. We still need a way to ensure that a dead bucket_table is never re-linked by rhashtable_walk_stop(). This can be achieved by calling call_rcu() inside the locked region, and checking with rcu_head_after_call_rcu() in rhashtable_walk_stop() to see if the bucket table is empty and dead. Acked-by:
Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by:
-
David S. Miller authored
Florian Fainelli says: ==================== net: phy: Move Omega PHY entry to Cygnus PHY driver In order to pave the way for adding some specific Omega PHY features that may not be desirable on other products covered by the bcm7xxx PHY driver, split the Omega PHY entry into the Cygnus PHY driver such that the PHY drivers are reflective of product lines/business units maintaining them within Broadcom. No functional changes intended. ==================== Acked-by:
Arun Parameswaran <arun.parameswaran@broadcom.com> Signed-off-by:
-
Florian Fainelli authored
Cygnus and Omega are part of the same business unit and product line, it makes sense to group PHY entries by products such that a platform can select only the drivers that it needs. Bring all the functionality that the BCM7XXX_28NM_GPHY() macro hides for us and remove the Omega PHY entry from bcm7xxx.c. As an added bonus, we now have a proper mdio_device_id entry to permit auto-loading. Signed-off-by:
Scott Branden <scott.branden@broadcom.com> Signed-off-by:
-
Florian Fainelli authored
The Omega PHY entry was added to bcm7xxx.c out of convenience and this breaks the one driver per product line paradigm that was applied up until now. Since the AFE initialization is shared between Omega and BCM7xxx move the relevant functions to bcm-phy-lib.[ch]. No functional changes introduced. Signed-off-by:
-
Julian Wiedmann authored
Get rid of some obsolete gc-related documentation and macros that were missed in commit 5b7c9a8f ("net: remove dst gc related code"). CC: Wei Wang <weiwan@google.com> Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Acked-by:
Wei Wang <weiwan@google.com> Signed-off-by:
-
David S. Miller authored
Florian Fainelli says: ==================== net: broadcom: Remove print of base address Some broadcom MDIO/switch/Ethernet MAC drivers insist on printing the base register virtual address which has little value. ==================== Signed-off-by: -
Florian Fainelli authored
Since commit ad67b74d ("printk: hash addresses printed with %p") pointers are being hashed when printed. Displaying the virtual memory at bootup time is not helpful, especially given we use a dev_info() which already displays the platform device's address. Signed-off-by:
-
Florian Fainelli authored
Since commit ad67b74d ("printk: hash addresses printed with %p") pointers are being hashed when printed. Displaying the virtual memory at bootup time is not helpful, we use a dev_info() print which already displays the platform device's address. Signed-off-by:
-
Florian Fainelli authored
Since commit ad67b74d ("printk: hash addresses printed with %p") pointers are being hashed when printed. Displaying the virtual memory at bootup time is not helpful, especially given we use a dev_info() which already displays the platform device's address. Signed-off-by:
-
David Ahern authored
net and null_fallback are redundant. Remove null_fallback in favor of !net check. Signed-off-by:
David Ahern <dsahern@gmail.com> Acked-by:
-
David Ahern authored
fib_trie implementation calls synchronize_rcu when a certain amount of pages are dirty from freed entries. The number of pages was determined experimentally in 2009 (commit c3059477). At the current setting, synchronize_rcu is called often -- 51 times in a second in one test with an average of an 8 msec delay adding a fib entry. The total impact is a lot of slow down modifying the fib. This is seen in the output of 'time' - the difference between real time and sys+user. For example, using 720,022 single path routes and 'ip -batch'[1]: $ time ./ip -batch ipv4/routes-1-hops real 0m14.214s user 0m2.513s sys 0m6.783s So roughly 35% of the actual time to install the routes is from the ip command getting scheduled out, most notably due to synchronize_rcu (this is observed using 'perf sched timehist'). This patch makes the amount of dirty memory configurable between 64k where the synchronize_rcu is called often (small, low end systems that are memory sensitive) to 64M where synchronize_rcu is called rarely during a large FIB change (for high end systems with lots of memory). The default is 512kB which corresponds to the current setting of 128 pages with a 4kB page size. As an example, at 16MB the worst interval shows 4 calls to synchronize_rcu in a second blocking for up to 30 msec in a single instance, and a total of almost 100 msec across the 4 calls in the second. The trade off is allowing FIB entries to consume more memory in a given time window but but with much better fib insertion rates (~30% increase in prefixes/sec). With this patch and net.ipv4.fib_sync_mem set to 16MB, the same batch file runs in: $ time ./ip -batch ipv4/routes-1-hops real 0m9.692s user 0m2.491s sys 0m6.769s So the dead time is reduced to about 1/2 second or <5% of the real time. [1] 'ip' modified to not request ACK messages which improves route insertion times by about 20% Signed-off-by:
-
Kirill Tkhai authored
Signed-off-by:
Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by:
-
Kirill Tkhai authored
In commit f2780d6d "tun: Add ioctl() SIOCGSKNS cmd to allow obtaining net ns of tun device" it was missed that tun may change its net ns, while net ns of socket remains the same as it was created initially. SIOCGSKNS returns net ns of socket, so it is not suitable for obtaining net ns of device. We may have two tun devices with the same names in two net ns, and in this case it's not possible to determ, which of them fd refers to (TUNGETIFF will return the same name). This patch adds new ioctl() cmd for obtaining net ns of a device. Reported-by:
Harald Albrecht <harald.albrecht@gmx.net> Signed-off-by:
-
David S. Miller authored
David Ahern says: ==================== ipv6: Change addrconf_f6i_alloc to use ip6_route_info_create addrconf_f6i_alloc is the last caller of fib6_info_alloc besides ip6_route_info_create. There really is no good reason for it do its own fib6_info initialization, so convert it to call ip6_route_info_create. ==================== Signed-off-by: -
David Ahern authored
Change addrconf_f6i_alloc to generate a fib6_config and call ip6_route_info_create. addrconf_f6i_alloc is the last caller to fib6_info_alloc besides ip6_route_info_create, and there is no reason for it to do its own initialization on a fib6_info. Host routes need to be created even if the device is down, so add a new flag, fc_ignore_dev_down, to fib6_config and update fib6_nh_init to not error out if device is not up. Notes on the conversion: - ip_fib_metrics_init is the same as fib6_config has fc_mx set to NULL and fc_mx_len set to 0 - dst_nocount is handled by the RTF_ADDRCONF flag - dst_host is handled by fc_dst_len = 128 nh_gw does not get set after the conversion to ip6_route_info_create but it should not be set in addrconf_f6i_alloc since this is a host route not a gateway route. Everything else is a straight forward map between fib6_info and fib6_config. Signed-off-by:
-
David Ahern authored
ip6_route_info_create is a low level function for ensuring fc_metric is set. Move the check and default setting to the 2 locations that do not already set fc_metric before calling ip6_route_info_create. This is required for the next patch which moves addrconf allocations to ip6_route_info_create and want the metric for host routes to be 0. Signed-off-by:
-
Vakul Garg authored
To free the skb in normal course of processing, consume_skb() should be used. Only for failure paths, skb_free() is intended to be used. https://www.kernel.org/doc/htmldocs/networking/API-consume-skb.htmlSigned-off-by:
Vakul Garg <vakul.garg@nxp.com> Signed-off-by:
-
Hoang Le authored
In commit c55c8eda ("tipc: smooth change between replicast and broadcast") we introduced new method to eliminate the risk of message reordering that happen in between different nodes. Unfortunately, we forgot checking at receiving side to ignore intra node. We fix this by checking and returning if arrived message from intra node. syzbot report: ================================================================== kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] PREEMPT SMP KASAN CPU: 0 PID: 7820 Comm: syz-executor418 Not tainted 5.0.0+ #61 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:tipc_mcast_filter_msg+0x21b/0x13d0 net/tipc/bcast.c:782 Code: 45 c0 0f 84 39 06 00 00 48 89 5d 98 e8 ce ab a5 fa 49 8d bc 24 c8 00 00 00 48 b9 00 00 00 00 00 fc ff df 48 89 f8 48 c1 e8 03 <80> 3c 08 00 0f 85 9a 0e 00 00 49 8b 9c 24 c8 00 00 00 48 be 00 00 RSP: 0018:ffff8880959defc8 EFLAGS: 00010202 RAX: 0000000000000019 RBX: ffff888081258a48 RCX: dffffc0000000000 RDX: 0000000000000000 RSI: ffffffff86cab862 RDI: 00000000000000c8 RBP: ffff8880959df030 R08: ffff8880813d0200 R09: ffffed1015d05bc8 R10: ffffed1015d05bc7 R11: ffff8880ae82de3b R12: 0000000000000000 R13: 000000000000002c R14: 0000000000000000 R15: ffff888081258a48 FS: 000000000106a880(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020001cc0 CR3: 0000000094a20000 CR4: 00000000001406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: tipc_sk_filter_rcv+0x182d/0x34f0 net/tipc/socket.c:2168 tipc_sk_enqueue net/tipc/socket.c:2254 [inline] tipc_sk_rcv+0xc45/0x25a0 net/tipc/socket.c:2305 tipc_sk_mcast_rcv+0x724/0x1020 net/tipc/socket.c:1209 tipc_mcast_xmit+0x7fe/0x1200 net/tipc/bcast.c:410 tipc_sendmcast+0xb36/0xfc0 net/tipc/socket.c:820 __tipc_sendmsg+0x10df/0x18d0 net/tipc/socket.c:1358 tipc_sendmsg+0x53/0x80 net/tipc/socket.c:1291 sock_sendmsg_nosec net/socket.c:651 [inline] sock_sendmsg+0xdd/0x130 net/socket.c:661 ___sys_sendmsg+0x806/0x930 net/socket.c:2260 __sys_sendmsg+0x105/0x1d0 net/socket.c:2298 __do_sys_sendmsg net/socket.c:2307 [inline] __se_sys_sendmsg net/socket.c:2305 [inline] __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2305 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4401c9 Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffd887fa9d8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 00000000004401c9 RDX: 0000000000000000 RSI: 0000000020002140 RDI: 0000000000000003 RBP: 00000000006ca018 R08: 0000000000000000 R09: 00000000004002c8 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000401a50 R13: 0000000000401ae0 R14: 0000000000000000 R15: 0000000000000000 Modules linked in: ---[ end trace ba79875754e1708f ]--- Reported-by: syzbot+be4bdf2cc3e85e952c50@syzkaller.appspotmail.com Fixes: c55c8eda ("tipc: smooth change between replicast and broadcast") Acked-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by:
-
