Michael Chan says:

====================
bnxt_en: Update for net-next.

This series includes the usual firmware spec. update, a PCI ID addition,
enhancements for VF trust, MDIO read/write for external PHY, and
fixing the return code when TC flow offload fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver returns -ENOSPC when tc_can_offload() check fails. Since that
routine checks for flow parameters that are not supported by the driver,
we should return the more appropriate -EOPNOTSUPP.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for SIOCGMIIREG and SIOCSMIIREG ioctls to
mdio read/write to external PHY.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newer firmware understands the concept of a trusted VF, so propagate the
trusted VF attribute set by the PF admin. to the firmware.  Also, check
the firmware trusted setting when considering the VF MAC address change
and reporting the trusted setting to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for BCM957504 with device ID 1751
Signed-off-by: Erik Burrows <erik.burrows@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware error recover is the major change in this spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each tls context maintains two cipher contexts (one each for tx and rx
directions). For each tls session, the constants such as protocol
version, ciphersuite, iv size, associated data size etc are same for
both the directions and need to be stored only once per tls context.
Hence these are moved from 'struct cipher_context' to 'struct
tls_prot_info' and stored only once in 'struct tls_context'.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c: In function 'bnx2x_get_hwinfo':
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:11940:10: warning:
 variable 'mfw_vn' set but not used [-Wunused-but-set-variable]

It's never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: add helpers for handling C45 10GBT AN register values

Similar to the existing helpers for the Clause 22 registers add helpers
to deal with converting Clause 45 advertisement registers to / from
link mode bitmaps.

Note that these helpers are defined in linux/mdio.h, not like the
Clause 22 helpers in linux/mii.h. Reason is that the Clause 45 register
constants are defined in uapi/linux/mdio.h. And uapi/linux/mdio.h
includes linux/mii.h before defining the C45 register constants.

v2:
- Remove few helpers which aren't used by this series. They will
  follow together with the users.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use mii_10gbt_stat_mod_linkmode_lpa_t() in genphy_c45_read_lpa() to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to the existing helpers for the Clause 22 registers add helper
mii_10gbt_stat_mod_linkmode_lpa_t.

Note that this helper is defined in linux/mdio.h, not like the
Clause 22 helpers in linux/mii.h. Reason is that the Clause 45 register
constants are defined in uapi/linux/mdio.h. And uapi/linux/mdio.h
includes linux/mii.h before defining the C45 register constants.

v2:
- remove helpers that don't have users in this series
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix following warning:

drivers/net/ethernet/cavium/liquidio/cn23xx_pf_device.c:1453:35: warning: Using plain integer as NULL pointer
drivers/net/ethernet/cavium/liquidio/lio_main.c:2910:23: warning: Using plain integer as NULL pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

writex() has implicit barriers, that's what makes it different from
writex_relaxed(). Therefore these calls to mmiowb() can be removed.

This patch was recently reverted due to a dependency with another
problematic patch. But because it didn't contribute to the problem
it was rebased and can be resubmitted.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RPS not work for DSA devices since the 'skb_get_hash'
will always get the invalid hash for dsa tagged packets.

"[PATCH] tag_mtk: add flow_dissect callback to the ops struct"
introduced the flow_dissect callback to get the right hash for
MTK tagged packet. Tag_dsa and tag_edsa  also need to implement
the callback.
Signed-off-by: Rundong Ge <rdong.ge@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix coccinelle warning:

./drivers/net/phy/mdio_bus.c:51:5-12: ERROR: PTR_ERR applied after initialization to constant on line 44
./drivers/net/phy/mdio_bus.c:52:5-12: ERROR: PTR_ERR applied after initialization to constant on line 44

fix this by using IS_ERR before PTR_ERR

Fixes: bafbdd52 ("phylib: Add device reset GPIO support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IP2ME packet trap is triggered by packets hitting local routes.
After evaluating current defaults used by the driver it was decided to
reduce the amount of traffic generated by this trap to 1Kpps and
increase the burst size. This is inline with similarly deployed systems.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This file does not use hweight*() at all, and the definition is
surrounded by #if 0 ... #endif.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS updates for net-next

The following patchset contains Netfilter/IPVS updates for you net-next
tree:

1) Missing NFTA_RULE_POSITION_ID netlink attribute validation,
   from Phil Sutter.

2) Restrict matching on tunnel metadata to rx/tx path, from wenxu.

3) Avoid indirect calls for IPV6=y, from Florian Westphal.

4) Add two indirections to prepare merger of IPV4 and IPV6 nat
   modules, from Florian Westphal.

5) Broken indentation in ctnetlink, from Colin Ian King.

6) Patches to use struct_size() from netfilter and IPVS,
   from Gustavo A. R. Silva.

7) Display kernel splat only once in case of racing to confirm
   conntrack from bridge plus nfqueue setups, from Chieh-Min Wang.

8) Skip checksum validation for layer 4 protocols that don't need it,
   patch from Alin Nastac.

9) Sparse warning due to symbol that should be static in CLUSTERIP,
   from Wei Yongjun.

10) Add new toggle to disable SDP payload translation when media
    endpoint is reachable though the same interface as the signalling
    peer, from Alin Nastac.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:2431:5: warning:
 symbol 'hclge_set_all_vf_rst' was not declared. Should it be static?

Fixes: aa5c4f17 ("net: hns3: add reset handling for VF when doing PF reset")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function meth_init_tx_ring() is called from meth_tx_timeout(),
in which spin_lock is held, so we should use GFP_ATOMIC instead.

Fixes: 8d4c28fb ("meth: pass struct device to DMA API functions")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch sets an error message in extack when the number of qdisc
handles exceeds the maximum. Also the error-code ENOSPC is more
appropriate than ENOMEM in this situation.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reported-by: Li Shuang <shuali@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY core expects PHY drivers not to set Pause and Asym_Pause bits,
unless the driver only wants to specify one of them due to HW
limitation. In the case of the Marvell10g driver, we don't need to set
them.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/dsa/bcm_sf2_cfp.c: In function 'bcm_sf2_cfp_ipv6_rule_set':
drivers/net/dsa/bcm_sf2_cfp.c:606:40: warning:
 variable 'v6_m_spec' set but not used [-Wunused-but-set-variable]
drivers/net/dsa/bcm_sf2_cfp.c:606:30: warning:
 variable 'v6_spec' set but not used [-Wunused-but-set-variable]

It not used any more after commit e4f7ef54 ("dsa: bcm_sf2: use flow_rule
infrastructure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check mask fields of tcp and ip flags when setting the corresponding mask
flag used in hardware.

Fixes: 8f256622 ("flow_offload: add flow_rule and flow_match")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
devlink: add the ability to update device flash

This series is the second step to allow trouble shooting and recovering
devices in bad state without the use of netdevs as handles.  We can
already query FW versions over devlink, now we add the ability to update
the FW.  This will allow drivers to implement some from of "limp-mode"
where the device can't really be used for networking and hence has no
netdev, but we can interrogate it over devlink and fix the broken FW.

Small but nice advantage of devlink is that it only holds the devlink
instance lock during flashing, unlike ethtool which holds rtnl_lock().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Devlink now allows updating device flash.  Implement this
callback.

Compared to ethtool update we no longer have to release
the networking locks - devlink doesn't take them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If driver does not support ethtool flash update operation
call into devlink.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add devlink flash update command. Advanced NICs have firmware
stored in flash and often cryptographically secured. Updating
that flash is handled by management firmware. Ethtool has a
flash update command which served us well, however, it has two
shortcomings:
 - it takes rtnl_lock unnecessarily - really flash update has
   nothing to do with networking, so using a networking device
   as a handle is suboptimal, which leads us to the second one:
 - it requires a functioning netdev - in case device enters an
   error state and can't spawn a netdev (e.g. communication
   with the device fails) there is no netdev to use as a handle
   for flashing.

Devlink already has the ability to report the firmware versions,
now with the ability to update the firmware/flash we will be
able to recover devices in bad state.

To enable updates of sub-components of the FW allow passing
component name.  This name should correspond to one of the
versions reported in devlink info.

v1: - replace target id with component name (Jiri).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: improve and use phy_resolve_aneg_linkmode

Improve phy_resolve_aneg_linkmode and use it in genphy_read_status.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have phy_resolve_aneg_linkmode() we can make
genphy_read_status() much simpler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have the settings array of modes which is sorted based on aneg
priority. Instead of checking each mode manually let's simply iterate
over the sorted settings.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check that filter is not NULL before passing it to tcf_walker->fn()
callback in cls_cgroup_walk(). This can happen when cls_cgroup_change()
failed to set first filter.

Fixes: ed76f5ed ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check that filter is not NULL before passing it to tcf_walker->fn()
callback. This can happen when mall_change() failed to offload filter to
hardware.

Fixes: ed76f5ed ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some classifiers set arg->stop in their implementation of tp->walk() API
when empty. Most of classifiers do not adhere to that convention. Do not
set arg->stop in route4_walk() to unify tp->walk() behavior among
classifier implementations.

Fixes: ed76f5ed ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some classifiers set arg->stop in their implementation of tp->walk() API
when empty. Most of classifiers do not adhere to that convention. Do not
set arg->stop in fw_walk() to unify tp->walk() behavior among classifier
implementations.

Fixes: ed76f5ed ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use existing skb_put_data() and skb_trim() instead of open-coding them,
with the skb_put_data() first so that logically, `skb` still contains the
data to be copied in its data..tail area when skb_put_data() reads it.
This change on its own is a cleanup, and it is also necessary for potential
future integration of skbuffs with things like KASAN.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a dedicated thermal zone for each QSFP/SFP module. The current
temperature is obtained from the module's temperature sensor and the
trip points are set based on the warning and critical thresholds
read from the module.

A cooling device (fan) is bound to all the thermal zones. The
thermal zone governor is set to user space in order to avoid
collisions between thermal zones.
For example, one thermal zone might want to increase the speed of
the fan, whereas another one would like to decrease it.

Deferring this decision to user space allows the user to the take
the most suitable decision.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roopa Prabhu says:

====================
tracepoints in neighbor subsystem

Roopa Prabhu (2):
  trace: events: add a few neigh tracepoints
  neigh: hook tracepoints in neigh update code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>