- 12 May, 2014 20 commits
-
-
Seungwon Jeon authored
Current implementation for bus speed mode selection is too complicated. This patch is to simplify the codes and remove some duplicate parts. The following changes are including: * Adds functions for each mode selection(HS, HS-DDR, HS200 and etc) * Rearranged the mode selection sequence with supported device type * Adds maximum speed for HS200 mode(hs200_max_dtr) * Adds field definition for HS_TIMING of EXT_CSD Signed-off-by:
Seungwon Jeon <tgih.jun@samsung.com> Tested-by:
Jaehoon Chung <jh80.chung@samsung.com> Acked-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Seungwon Jeon authored
Power class is changed once only after selection of bus modes including speed and bus-width finishes finally. Signed-off-by:
Seungwon Jeon <tgih.jun@samsung.com> Tested-by:
Jaehoon Chung <jh80.chung@samsung.com> Acked-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Seungwon Jeon authored
Device types which are supported by both host and device can be identified when EXT_CSD is read. There is no need to check host's capability anymore. Signed-off-by:
Seungwon Jeon <tgih.jun@samsung.com> Tested-by:
Jaehoon Chung <jh80.chung@samsung.com> Acked-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Seungwon Jeon authored
Timing mode identifier has same role and can take the place of speed mode. This change removes all related speed mode. Signed-off-by:
Seungwon Jeon <tgih.jun@samsung.com> Tested-by:
Jaehoon Chung <jh80.chung@samsung.com> Acked-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Sebastian Hesselbarth authored
SDIO controllers found on Marvell Kirkwood SoCs seem to cause a late, spurious irq although all interrupts have been disabled. This irq doesn't do any harm, neither to HW nor driver. To avoid some "unexpected irq" warning later, we workaround above issue by bailing out of irq handler early, if we didn't expect any. Signed-off-by:
Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by:
Jason Cooper <jason@lakedaemon.net> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Sebastian Hesselbarth authored
mvsdio reports method of card detection with dev_notice, while for removable cards it may be sane, for non-removable cards it is not. Also, as the user cannot do anything about it, silence the message by reducing it from dev_notice to dev_dbg. Signed-off-by:
Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by:
Jason Cooper <jason@lakedaemon.net> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Tim Kryger authored
The eMMC signalling voltage is determined by VCCQ which is provided to the card by the host. Signalling is not required to begin at 3.3v and, if the host and card both support a particular VCC/VCCQ combination, it can be used immediately. In contrast, SD Cards must begin with 3.3v signalling and may switch to a lower voltage signalling if instructed to do so in CMD11. A message is required to coordinate this operation because the card only receives a 3.3v VDD and must know when to use the 1.8v produced by its internal regulator. It makes sense for the core to begin with 3.3v signalling but when that can't be set, 1.8v and 1.2v signalling also should be attempted. This is especially important when an external regulator with a limited range is used to supply VCCQ to an eMMC part. Signed-off-by:
Tim Kryger <tim.kryger@linaro.org> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Jonas Jensen authored
Add SD/MMC driver for MOXA ART SoCs. The "MOXA ART MMC controller" is likely a faraday "ftsdc010", a controller with support in U-Boot: http://git.denx.de/?p=u-boot.git;a=blob;f=drivers/mmc/ftsdc010_mci.cSigned-off-by:
Jonas Jensen <jonas.jensen@gmail.com> Acked-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Roger Tseng authored
Realtek USB SD/MMC host driver provides mmc host support based on the Realtek USB card reader MFD driver. Signed-off-by:
Roger Tseng <rogerable@realtek.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Axel Lin authored
NUM_GPIOS is not used after e19499ae ("mmc: sdhci-s3c: let device core setup the default pin configuration"). Thus remove it. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Acked-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Jaehoon Chung authored
Restore the card-present checking point. (The following part was removed from commit bf626e55 ("mmc: dw_mmc: use slot-gpio to handle cd pin") Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Jaehoon Chung authored
If mmc_of_parse() is used, dw_mci_of_get_cd_gpio/wp_gpio didn't need. Already implemented into mmc_of_parse(). Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Jaehoon Chung authored
Remove unnecessary function. This function didn't re-use anywhere. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Jaehoon Chung authored
Fixed an indentation block. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Jaehoon Chung authored
Since using the device-tree, didn't use the callback pointer. So removed the unused callback pointer. When the set_power callback is used, it should be added in future. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Jaehoon Chung authored
It's right to check immediately whether host->bus_hz is assigned or not. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Jaehoon Chung authored
mmc_of_parse() have been already parsed the general capability. Didn't need to use the local parser. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Acked-by:
Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Alexander Shiyan authored
Signed-off-by:
Alexander Shiyan <shc_work@mail.ru> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Alexander Shiyan authored
Replace existing resource handling in the driver with managed device resource, this ensures more consistent error values and simplifies error paths. Signed-off-by:
Alexander Shiyan <shc_work@mail.ru> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Sachin Kamat authored
'dw_mci_exynos_pmops' is local to this file. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Acked-by:
Jaehoon Chung <jh80.chung@samsung.com> Acked-by:
Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
- 22 Apr, 2014 6 commits
-
-
Micky Ching authored
a27fbf2f ("mmc: add ignorance case for CMD13 CRC error") produced a cmd.flags unhandled in realtek pci host driver. This will make MMC card fail to initialize, this patch is used to handle the new cmd.flags condition and MMC card can be used. Signed-off-by:
Micky Ching <micky_ching@realsil.com.cn> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Ulf Hansson authored
The sdio func device is added to the driver model after the card device. This means the sdio func device will be suspend before the card device and thus resumed after. The consequence are the mmc core don't explicity need to protect itself from receiving sdio requests in suspended state. Instead that can be handled from the sdio bus, which is thus invokes the PM callbacks instead of old dummy function. In the case were the sdio func driver don't implement the PM callbacks the mmc core will in the early phase of system suspend, remove the card from the driver model and thus power off it. Cc: Aaron Lu <aaron.lu@intel.com> Cc: NeilBrown <neilb@suse.de> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by:
Aaron Lu <aaron.lu@intel.com> Tested-by:
xiaoming wang <xiaoming.wang@intel.com> Tested-by:
Chuanxiao Dong <chuanxiao.dong@intel.com> Signed-off-by:
Chris Ball <chris@printf.net>
-
Stefan Wahren authored
When plugging a specific micro SD card at MMC socket of a custom i.MX28 board, we get the following kernel warning: WARNING: CPU: 0 PID: 30 at drivers/mmc/host/mxs-mmc.c:342 mxs_mmc_start_cmd+0x34c/0x378() Modules linked in: CPU: 0 PID: 30 Comm: kworker/u2:1 Not tainted 3.14.0-rc5 #8 Workqueue: kmmcd mmc_rescan [<c0015420>] (unwind_backtrace) from [<c0012cb0>] (show_stack+0x10/0x14) [<c0012cb0>] (show_stack) from [<c001daf8>] (warn_slowpath_common+0x6c/0x8c) [<c001daf8>] (warn_slowpath_common) from [<c001db34>] (warn_slowpath_null+0x1c/0x24) [<c001db34>] (warn_slowpath_null) from [<c0349478>] (mxs_mmc_start_cmd+0x34c/0x378) [<c0349478>] (mxs_mmc_start_cmd) from [<c0338fa0>] (mmc_start_request+0xc4/0xf4) [<c0338fa0>] (mmc_start_request) from [<c03390b4>] (mmc_wait_for_req+0x50/0x164) [<c03390b4>] (mmc_wait_for_req) from [<c03405b8>] (mmc_app_send_scr+0x158/0x1c8) [<c03405b8>] (mmc_app_send_scr) from [<c033ee1c>] (mmc_sd_setup_card+0x80/0x3c8) [<c033ee1c>] (mmc_sd_setup_card) from [<c033f788>] (mmc_sd_init_card+0x124/0x66c) [<c033f788>] (mmc_sd_init_card) from [<c033fd7c>] (mmc_attach_sd+0xac/0x174) [<c033fd7c>] (mmc_attach_sd) from [<c033a658>] (mmc_rescan+0x25c/0x2d8) [<c033a658>] (mmc_rescan) from [<c003597c>] (process_one_work+0x1b4/0x4ec) [<c003597c>] (process_one_work) from [<c0035de4>] (worker_thread+0x130/0x464) [<c0035de4>] (worker_thread) from [<c003c824>] (kthread+0xb4/0xd0) [<c003c824>] (kthread) from [<c000f420>] (ret_from_fork+0x14/0x34) The error is due to an invalid value in CSD register of a specific 2GB micro SD card. The CSD version of this card is 1.0 but the TACC field has the invalid value 0. cid:0000005553442020000000000000583f csd:00000032535a83bfedb7ffbf1680003f date:08/2005 erase_size:512 fwrev:0x0 hwrev:0x0 manfid:0x000000 name:USD oemid:0x0000 preferred_erase_size:4194304 scr:0225000000000000 serial:0x00000000 type:SD Since the kernel is making use of this TACC field to calculate the SD card timeout, an invalid value 0 leads to a warning at mxs_ns_to_ssp_ticks() and later the following misleading error message appears in a loop: mxs-mmc 80010000.ssp: card claims to support voltages below defined range mxs-mmc 80010000.ssp: no support for card's volts mmc0: error -22 whilst initialising MMC card This error is only found on this 2GB SD card on mxs platform. On x86 this card works without any problems. The following patch based on the work of Peter Chan and Otavio Salvador. It catches the case that the determined timeout is still 0 and sets it to a valid value. Successful tested on a i.MX28 board. Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Axel Lin authored
Use new ATTRIBUTE_GROUPS macro to declare attribute groups. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Fabio Estevam authored
Fix the following sparse warnings: drivers/mmc/card/block.c:2421:9: warning: Using plain integer as NULL pointer drivers/mmc/core/quirks.c:69:9: warning: Using plain integer as NULL pointer Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Markus Mayer authored
This change removes the callback from atomic context which it doesn't need to be in, and puts it in line with the debounced rescan. This code is based on these e-mail threads with Christian Daudt: https://lkml.org/lkml/2013/8/19/539 https://lkml.org/lkml/2014/3/19/79Signed-off-by:
Markus Mayer <markus.mayer@linaro.org> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
- 20 Apr, 2014 12 commits
-
-
Seungwon Jeon authored
Added MMC_DDR52 as eMMC's DDR mode is distinguished from SD-UHS. Signed-off-by:
Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Seungwon Jeon authored
Replaced UHS_DDR50 with MMC_DDR52. And MMC_CAP_UHS_DDR50 is removed because of non-implementation of UHS signaling. Signed-off-by:
Seungwon Jeon <tgih.jun@samsung.com> Acked-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Seungwon Jeon authored
Added MMC_DDR52 as eMMC's DDR mode is distinguished from SD-UHS. CC: Wei WANG <wei_wang@realsil.com.cn> CC: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Seungwon Jeon authored
Replaced UHS_DDR50 with MMC_DDR52. CC: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Seungwon Jeon authored
Replaced UHS_DDR50 with MMC_DDR52. Signed-off-by:
Seungwon Jeon <tgih.jun@samsung.com> Acked-by:
Balaji T K <balajitk@ti.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Seungwon Jeon authored
Added MMC_DDR52 as eMMC's DDR mode distinguished from SD-UHS. CC: Russell King <linux@arm.linux.org.uk> Signed-off-by:
Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Seungwon Jeon authored
This change distinguishes DDR timing mode of current mixed usage to clarify device type. Signed-off-by:
Seungwon Jeon <tgih.jun@samsung.com> Acked-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Chris Ball <chris@printf.net>
-
Linus Torvalds authored
-
git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds authored
Pull slave-dmaengine fixes from Vinod Koul: "Back from long weekend here in India and now the time to send fixes for slave dmaengine. - Dan's fix of sirf xlate code - Jean's fix for timberland - edma fixes by Sekhar for SG handling and Yuan for changing init call" * 'fixes' of git://git.infradead.org/users/vkoul/slave-dma: dma: fix eDMA driver as a subsys_initcall dmaengine: sirf: off by one in of_dma_sirfsoc_xlate() platform: Fix timberdale dependencies dma: edma: fix incorrect SG list handling
-
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommuLinus Torvalds authored
Pull iommu fixes from Joerg Roedel: "Fixes for regressions: - fix wrong IOMMU enumeration causing some SCSI device drivers initialization failures - ARM-SMMU fixes for a panic condition and a wrong return value" * tag 'iommu-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: iommu/arm-smmu: fix panic in arm_smmu_alloc_init_pte iommu/arm-smmu: Return 0 on unmap failure iommu/vt-d: fix bug in matching PCI devices with DRHD/RMRR descriptors iommu/vt-d: Fix get_domain_for_dev() handling of upstream PCIe bridges iommu/vt-d: fix memory leakage caused by commit ea8ea460
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf tooling fixes from Ingo Molnar: "Three small tooling fixes" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf tools: Improve error reporting perf tools: Adjust symbols in VDSO perf kvm: Fix 'Min time' counting in report command
-
Ingo Molnar authored
Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/jolsa/perf into perf/urgent Pull perf/urgent fixes from Jiri Olsa: User visible changes: * Adjust symbols in VDSO to properly resolve its function names (Vladimir Nikulichev) * Improve error reporting for record session failure (Adrien BAK) * Fix 'Min time' counting in report command (Alexander Yarygin) Signed-off-by:
Jiri Olsa <jolsa@redhat.com> Signed-off-by:
Ingo Molnar <mingo@kernel.org>
-
- 19 Apr, 2014 2 commits
-
-
Adrien BAK authored
In the current version, when using perf record, if something goes wrong in tools/perf/builtin-record.c:375 session = perf_session__new(file, false, NULL); The error message: "Not enough memory for reading per file header" is issued. This error message seems to be outdated and is not very helpful. This patch proposes to replace this error message by "Perf session creation failed" I believe this issue has been brought to lkml: https://lkml.org/lkml/2014/2/24/458 although this patch only tackles a (small) part of the issue. Additionnaly, this patch improves error reporting in tools/perf/util/data.c open_file_write. Currently, if the call to open fails, the user is unaware of it. This patch logs the error, before returning the error code to the caller. Reported-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Adrien BAK <adrien.bak@metascale.org> Link: http://lkml.kernel.org/r/1397786443.3093.4.camel@beast [ Reorganize the changelog into paragraphs ] [ Added empty line after fd declaration in open_file_write ] Signed-off-by:
Jiri Olsa <jolsa@redhat.com>
-
Vladimir Nikulichev authored
pert-report doesn't resolve function names in VDSO: $ perf report --stdio -g flat,0.0,15,callee --sort pid ... 8.76% 0x7fff6b1fe861 __gettimeofday ACE_OS::gettimeofday() ... In this case symbol values should be adjusted the same way as for executables, relocatable objects and prelinked libraries. After fix: $ perf report --stdio -g flat,0.0,15,callee --sort pid ... 8.76% __vdso_gettimeofday __gettimeofday ACE_OS::gettimeofday() Signed-off-by:
Vladimir Nikulichev <nvs@tbricks.com> Tested-by:
Namhyung Kim <namhyung@kernel.org> Reviewed-by:
Adrian Hunter <adrian.hunter@intel.com> Link: http://lkml.kernel.org/r/969812.163009436-sendEmail@nvsSigned-off-by:
Jiri Olsa <jolsa@redhat.com>
-