Create a single function that flushes everything (FP, VMX, VSX, SPE).
Doing this all at once means we only do one MSR write.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Create a single function that gives everything up (FP, VMX, VSX, SPE).
Doing this all at once means we only do one MSR write.

A context switch microbenchmark using yield():

http://ozlabs.org/~anton/junkcode/context_switch2.c

./context_switch2 --test=yield --fp --altivec --vector 0 0

shows an improvement of 3% on POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
[mpe: giveup_all() needs to be EXPORT_SYMBOL'ed]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

More consolidation of our MSR available bit handling.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add a boot option that strictly manages the MSR unavailable bits.
This catches kernel uses of FP/Altivec/SPE that would otherwise
corrupt user state.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The enable_kernel_*() functions leave the relevant MSR bits enabled
until we exit the kernel sometime later. Create disable versions
that wrap the kernel use of FP, Altivec VSX or SPE.

While we don't want to disable it normally for performance reasons
(MSR writes are slow), it will be used for a debug boot option that
does this and catches bad uses in other areas of the kernel.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Create helper functions to set and clear MSR bits after first
checking if they are already set. Grouping them will make it
easy to avoid the MSR writes in a subsequent optimisation.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

With the recent change to enable_kernel_vsx(), we no longer need
to call enable_kernel_fp() and enable_kernel_altivec().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Move the MSR modification into c. Removing it from the assembly
function will allow us to avoid costly MSR writes by batching them
up.

Check the FP and VMX bits before calling the relevant giveup_*()
function. This makes giveup_vsx() and flush_vsx_to_thread() perform
more like their sister functions, and allows us to use
flush_vsx_to_thread() in the signal code.

Move the check_if_tm_restore_required() check in.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Move the MSR modification into new c functions. Removing it from
the low level functions will allow us to avoid costly MSR writes
by batching them up.

Move the check_if_tm_restore_required() check into these new functions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We used to allow giveup_*() to be called with a NULL task struct
pointer. Now those cases are handled in the caller we can remove
the checks. We can also remove giveup_altivec_notask() which is also
unused.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

mtmsrd_isync() will do an mtmsrd followed by an isync on older
processors. On newer processors we avoid the isync via a feature fixup.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Instead of having multiple giveup_*_maybe_transactional() functions,
separate out the TM check into a new function called
check_if_tm_restore_required().

This will make it easier to optimise the giveup_*() functions in a
subsequent patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The UP only lazy floating point and vector optimisations were written
back when SMP was not common, and neither glibc nor gcc used vector
instructions. Now SMP is very common, glibc aggressively uses vector
instructions and gcc autovectorises.

We want to add new optimisations that apply to both UP and SMP, but
in preparation for that remove these UP only optimisations.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

No need to execute mflr twice.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Move all our context switch SPR save and restore code into two
helpers. We do a few optimisations:

- Group all mfsprs and all mtsprs. In many cases an mtspr sets a
scoreboarding bit that an mfspr waits on, so the current practise of
mfspr A; mtspr A; mfpsr B; mtspr B is the worst scheduling we can
do.

- SPR writes are slow, so check that the value is changing before
writing it.

A context switch microbenchmark using yield():

http://ozlabs.org/~anton/junkcode/context_switch2.c

./context_switch2 --test=yield 0 0

shows an improvement of almost 10% on POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Similar to the non TM load_up_*() functions, don't disable the MSR
bits on the way out.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Writing the MSR is slow, so we want to avoid it whenever possible.

A subsequent patch will add a debug option that strictly manages the
FP/VMX/VSX unavailable bits. For now just remove it, matching what
we do in other areas of the kernel (eg enable_kernel_altivec()).

A context switch microbenchmark using yield():

http://ozlabs.org/~anton/junkcode/context_switch2.c

./context_switch2 --test=yield --fp 0 0

shows an improvement of almost 3% on POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Currently, if HV KVM is configured but PR KVM isn't, we don't include
a test to see whether we were interrupted in KVM guest context for the
set of interrupts which get delivered directly to the guest by hardware
if they occur in the guest.  This includes things like program
interrupts.

However, the recent bug where userspace could set the MSR for a VCPU
to have an illegal value in the TS field, and thus cause a TM Bad Thing
type of program interrupt on the hrfid that enters the guest, showed that
we can never be completely sure that these interrupts can never occur
in the guest entry/exit code.  If one of these interrupts does happen
and we have HV KVM configured but not PR KVM, then we end up trying to
run the handler in the host with the MMU set to the guest MMU context,
which generally ends badly.

Thus, for robustness it is better to have the test in every interrupt
vector, so that if some way is found to trigger some interrupt in the
guest entry/exit path, we can handle it without immediately crashing
the host.

This means that the distinction between KVMTEST and KVMTEST_PR goes
away.  Thus we delete KVMTEST_PR and associated macros and use KVMTEST
everywhere that we previously used either KVMTEST_PR or KVMTEST.  It
also means that SOFTEN_TEST_HV_201 becomes the same as SOFTEN_TEST_PR,
so we deleted SOFTEN_TEST_HV_201 and use SOFTEN_TEST_PR instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

It is common practice with powerpc to use 'rN' to refer to register 'N'. However
when using the pt_regs_offset table we have to use 'gprN'.

So add aliases such that both 'rN' and 'gprN' can be used.

For example, we can currently do:
  $ su -
  $ cd /sys/kernel/debug/tracing
  $ echo "p:probe/sys_fchownat sys_fchownat %gpr3:s32 +0(%gpr4):string %gpr5:s32 %gpr6:s32 %gpr7:s32" > kprobe_events
  $ echo 1 > events/probe/sys_fchownat/enable
  $ touch /tmp/foo
  $ chown root /tmp/foo
  $ echo 0 > events/enable
  $ cat trace
    chown-2925  [014] d...    76.160657: sys_fchownat: (SyS_fchownat+0x8/0x1a0) arg1=-100 arg2="/tmp/foo" arg3=0 arg4=-1 arg5=0

Instead we'd like to be able to use:
 $ echo "p:probe/sys_fchownat sys_fchownat %r3:s32 +0(%r4):string %r5:s32 %r6:s32 %r7:s32" > kprobe_events
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Most architectures use NR_syscalls as the #define for the number of syscalls.

We use __NR_syscalls, and then define NR_syscalls as __NR_syscalls.

__NR_syscalls is not used outside arch code, whereas NR_syscalls is. So as
NR_syscalls must be defined and __NR_syscalls does not, replace __NR_syscalls
with NR_syscalls.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This function has been unused since commit 14cf11af ("powerpc: Merge enough
to start building in arch/powerpc."), so remove it.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

if the language is not english objdump output is not parsed correctly
and format is "". Later, "ld -m $format" fails.

This patch adds "LANG=C" to force english output for objdump.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Since gpio1 is not a timer, it also should not use IRQF_TIMER.

Similar to commit ba461f09 ("powerpc: Use IRQF_NO_SUSPEND not
IRQF_TIMER for non-timer interrupts").
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The xmon and cascade irq handlers must not run as threads.
pmac_pic_lock is already a raw_spinlock, but the irq flag
IRQF_NO_THREAD needs to be set as well.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When writing a value to config space, cxl_pcie_write_config() calls
cxl_pcie_config_info() to obtain a mask and shift value, shifts the new
value accordingly, then uses the mask to combine the shifted value with the
existing value at the address as part of a read-modify-write pattern.

Currently, we use a logical OR operator rather than a bitwise OR operator,
which means any use of this function results in an incorrect value being
written. Replace the logical OR operator with a bitwise OR operator so the
value is written correctly.
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: stable@vger.kernel.org
Fixes: 6f7f0b3d ("cxl: Add AFU virtual PHB and kernel API")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

An idr warning is reported when a context is release after the capi card
is unbound from the cxl driver via sysfs. Below are the steps to
reproduce:

1. Create multiple afu contexts in an user-space application using libcxl.
2. Unbind capi card from cxl using command of form
   echo <capi-card-pci-addr> > /sys/bus/pci/drivers/cxl-pci/unbind
3. Exit/kill the application owning afu contexts.

After above steps a warning message is usually seen in the kernel logs
of the form "idr_remove called for id=<context-id> which is not
allocated."

This is caused by the function cxl_release_afu which destroys the
contexts_idr table. So when a context is release no entry for context pe
is found in the contexts_idr table and idr code prints this warning.

This patch fixes this issue by increasing & decreasing the ref-count on
the afu device when a context is initialized or when its freed
respectively. This prevents the afu from being released until all the
afu contexts have been released. The patch introduces two new functions
namely cxl_afu_get/put that manage the ref-count on the afu device.

Also the patch removes code inside cxl_dev_context_init that increases ref
on the afu device as its guaranteed to be alive during this function.
Reported-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Merge slub bulk allocator updates from Andrew Morton:
 "This missed the merge window because I was waiting for some repairs to
  come in.  Nothing actually uses the bulk allocator yet and the changes
  to other code paths are pretty small.  And the net guys are waiting
  for this so they can start merging the client code"

More comments from Jesper Dangaard Brouer:
 "The kmem_cache_alloc_bulk() call, in mm/slub.c, were included in
  previous kernel.  The present version contains a bug.  Vladimir
  Davydov noticed it contained a bug, when kernel is compiled with
  CONFIG_MEMCG_KMEM (see commit 03ec0ed5: "slub: fix kmem cgroup
  bug in kmem_cache_alloc_bulk").  Plus the mem cgroup counterpart in
  kmem_cache_free_bulk() were missing (see commit 03374518 "slub:
  add missing kmem cgroup support to kmem_cache_free_bulk").

  I don't consider the fix stable-material because there are no in-tree
  users of the API.

  But with known bugs (for memcg) I cannot start using the API in the
  net-tree"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  slab/slub: adjust kmem_cache_alloc_bulk API
  slub: add missing kmem cgroup support to kmem_cache_free_bulk
  slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
  slub: optimize bulk slowpath free by detached freelist
  slub: support for bulk free with SLUB freelists

Pull tty/serial fixes from Greg KH:
 "Here are a few small tty/serial driver fixes for 4.4-rc2 that resolve
  some reported problems.

  All have been in linux-next, full details are in the shortlog below"

* tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: export fsl8250_handle_irq
  serial: 8250_mid: Add missing dependency
  tty: audit: Fix audit source
  serial: etraxfs-uart: Fix crash
  serial: fsl_lpuart: Fix earlycon support
  bcm63xx_uart: Use the device name when registering an interrupt
  tty: Fix direct use of tty buffer work
  tty: Fix tty_send_xchar() lock order inversion

Pull staging/IIO fixes from Greg KH:
 "Here are some staging and iio driver fixes for 4.4-rc2.  All of these
  are in response to issues that have been reported and have been in
  linux-next for a while"

* tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Revert "Staging: wilc1000: coreconfigurator: Drop unneeded wrapper functions"
  iio: adc: xilinx: Fix VREFN scale
  iio: si7020: Swap data byte order
  iio: adc: vf610_adc: Fix division by zero error
  iio:ad7793: Fix ad7785 product ID
  iio: ad5064: Fix ad5629/ad5669 shift
  iio:ad5064: Make sure ad5064_i2c_write() returns 0 on success
  iio: lpc32xx_adc: fix warnings caused by enabling unprepared clock
  staging: iio: select IRQ_WORK for IIO_DUMMY_EVGEN
  vf610_adc: Fix internal temperature calculation

Pull USB fixes from Greg KH:
 "Here are a number of USB fixes and new device ids for 4.4-rc2.  All
  have been in linux-next and the details are in the shortlog"

* tag 'usb-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
  usblp: do not set TASK_INTERRUPTIBLE before lock
  USB: MAINTAINERS: cxacru
  usb: kconfig: fix warning of select USB_OTG
  USB: option: add XS Stick W100-2 from 4G Systems
  xhci: Fix a race in usb2 LPM resume, blocking U3 for usb2 devices
  usb: xhci: fix checking ep busy for CFC
  xhci: Workaround to get Intel xHCI reset working more reliably
  usb: chipidea: imx: fix a possible NULL dereference
  usb: chipidea: usbmisc_imx: fix a possible NULL dereference
  usb: chipidea: otg: gadget module load and unload support
  usb: chipidea: debug: disable usb irq while role switch
  ARM: dts: imx27.dtsi: change the clock information for usb
  usb: chipidea: imx: refine clock operations to adapt for all platforms
  usb: gadget: atmel_usba_udc: Expose correct device speed
  usb: musb: enable usb_dma parameter
  usb: phy: phy-mxs-usb: fix a possible NULL dereference
  usb: dwc3: gadget: let us set lower max_speed
  usb: musb: fix tx fifo flush handling
  usb: gadget: f_loopback: fix the warning during the enumeration
  usb: dwc2: host: Fix remote wakeup when not in DWC2_L2
  ...

Pull MIPS fixes from Ralf Baechle:

 - Fix a flood of annoying build warnings

 - A number of fixes for Atheros 79xx platforms

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: ath79: Add a machine entry for booting OF machines
  MIPS: ath79: Fix the size of the MISC INTC registers in ar9132.dtsi
  MIPS: ath79: Fix the DDR control initialization on ar71xx and ar934x
  MIPS: Fix flood of warnings about comparsion being always true.

Pull parisc update from Helge Deller:
 "This patchset adds Huge Page and HUGETLBFS support for parisc"

Honestly, the hugepage support should have gone through in the merge
window, and is not really an rc-time fix.  But it only touches
arch/parisc, and I cannot find it in myself to care.  If one of the
three parisc users notices a breakage, I will point at Helge and make
rude farting noises.

* 'parisc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Map kernel text and data on huge pages
  parisc: Add Huge Page and HUGETLBFS support
  parisc: Use long branch to do_syscall_trace_exit
  parisc: Increase initial kernel mapping to 32MB on 64bit kernel
  parisc: Initialize the fault vector earlier in the boot process.
  parisc: Add defines for Huge page support
  parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
  parisc: Drop definition of start_thread_som for HP-UX SOM binaries
  parisc: Fix wrong comment regarding first pmd entry flags

Pull perf tool fixes from Thomas Gleixner:
 "A couple of fixes for perf tools:

   - Build system updates

   - Plug a memory leak in an error path of perf probe

   - Tear down probes correctly when adding fails

   - Fixes to the perf symbol handling

   - Fix ordering of event processing in buildid-list

   - Fix per DSO filtering in the histogram browser"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf probe: Clear probe_trace_event when add_probe_trace_event() fails
  perf probe: Fix memory leaking on failure by clearing all probe_trace_events
  perf inject: Also re-pipe lost_samples event
  perf buildid-list: Requires ordered events
  perf symbols: Fix dso lookup by long name and missing buildids
  perf symbols: Allow forcing reading of non-root owned files by root
  perf hists browser: The dso can be obtained from popup_action->ms.map->dso
  perf hists browser: Fix 'd' hotkey action to filter by DSO
  perf symbols: Rebuild rbtree when adjusting symbols for kcore
  tools: Add a "make all" rule
  tools: Actually install tmon in the install rule

Pull x86 fixes from Thomas Gleixner:
 "This update contains:

   - MPX updates for handling 32bit processes

   - A fix for a long standing bug in 32bit signal frame handling
     related to FPU/XSAVE state

   - Handle get_xsave_addr() correctly in KVM

   - Fix SMAP check under paravirtualization

   - Add a comment to the static function trace entry to avoid further
     confusion about the difference to dynamic tracing"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Fix SMAP check in PVOPS environments
  x86/ftrace: Add comment on static function tracing
  x86/fpu: Fix get_xsave_addr() behavior under virtualization
  x86/fpu: Fix 32-bit signal frame handling
  x86/mpx: Fix 32-bit address space calculation
  x86/mpx: Do proper get_user() when running 32-bit binaries on 64-bit kernels

Adjust kmem_cache_alloc_bulk API before we have any real users.

Adjust API to return type 'int' instead of previously type 'bool'.  This
is done to allow future extension of the bulk alloc API.

A future extension could be to allow SLUB to stop at a page boundary, when
specified by a flag, and then return the number of objects.

The advantage of this approach, would make it easier to make bulk alloc
run without local IRQs disabled.  With an approach of cmpxchg "stealing"
the entire c->freelist or page->freelist.  To avoid overshooting we would
stop processing at a slab-page boundary.  Else we always end up returning
some objects at the cost of another cmpxchg.

To keep compatible with future users of this API linking against an older
kernel when using the new flag, we need to return the number of allocated
objects with this API change.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Initial implementation missed support for kmem cgroup support in
kmem_cache_free_bulk() call, add this.

If CONFIG_MEMCG_KMEM is not enabled, the compiler should be smart enough
to not add any asm code.

Incoming bulk free objects can belong to different kmem cgroups, and
object free call can happen at a later point outside memcg context.  Thus,
we need to keep the orig kmem_cache, to correctly verify if a memcg object
match against its "root_cache" (s->memcg_params.root_cache).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>