Skip to content

L
linux
Switch branch/tag
  1. 29 May, 2023 3 commits
  3. 19 May, 2023 3 commits
  5. 17 May, 2023 5 commits
    • Yangyang Li's avatar
      RDMA/hns: Modify the value of long message loopback slice · 56518a60
      Yangyang Li authored 
      Long message loopback slice is used for achieving traffic balance between
QPs. It prevents the problem that QPs with large traffic occupying the
hardware pipeline for a long time and QPs with small traffic cannot be
scheduled.

Currently, its maximum value is set to 16K, which means only after a QP
sends 16K will the second QP be scheduled. This value is too large, which
will lead to unbalanced traffic scheduling, and thus it needs to be
modified.

The setting range of the long message loopback slice is modified to be
from 1024 (the lower limit supported by hardware) to mtu. Actual testing
shows that this value can significantly reduce error in hardware traffic
scheduling.

This solution is compatible with both HIP08 and HIP09. The modified
lp_pktn_ini has a maximum value of 2 (when mtu is 256), so the range
checking code for lp_pktn_ini is no longer necessary and needs to be
deleted.

Fixes: 0e60778e ("RDMA/hns: Modify the value of MAX_LP_MSG_LEN to meet hardware compatibility")
Link: https://lore.kernel.org/r/20230512092245.344442-4-huangjunxian6@hisilicon.comSigned-off-by: default avatarYangyang Li <liyangyang20@huawei.com>
Signed-off-by: default avatarJunxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: default avatarJason Gunthorpe <jgg@nvidia.com>
      56518a60
    • Chengchang Tang's avatar
      RDMA/hns: Fix base address table allocation · 7f3969b1
      Chengchang Tang authored 
      For hns, the specification of an entry like resource (E.g. WQE/CQE/EQE)
depends on BT page size, buf page size and hopnum. For user mode, the buf
page size depends on UMEM. Therefore, the actual specification is
controlled by BT page size and hopnum.

The current BT page size and hopnum are obtained from firmware. This makes
the driver inflexible and introduces unnecessary constraints.  Resource
allocation failures occur in many scenarios.

This patch will calculate whether the BT page size set by firmware is
sufficient before allocating BT, and increase the BT page size if it is
insufficient.

Fixes: 11334014 ("RDMA/hns: Optimize base address table config flow for qp buffer")
Link: https://lore.kernel.org/r/20230512092245.344442-3-huangjunxian6@hisilicon.comSigned-off-by: default avatarChengchang Tang <tangchengchang@huawei.com>
Signed-off-by: default avatarJunxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: default avatarJason Gunthorpe <jgg@nvidia.com>
      7f3969b1
    • Chengchang Tang's avatar
      RDMA/hns: Fix timeout attr in query qp for HIP08 · 58caa2a5
      Chengchang Tang authored 
      On HIP08, the queried timeout attr is different from the timeout attr
configured by the user.

It is found by rdma-core testcase test_rdmacm_async_traffic:

======================================================================
FAIL: test_rdmacm_async_traffic (tests.test_rdmacm.CMTestCase)
----------------------------------------------------------------------
Traceback (most recent call last):
  File "./tests/test_rdmacm.py", line 33, in test_rdmacm_async_traffic
    self.two_nodes_rdmacm_traffic(CMAsyncConnection, self.rdmacm_traffic,
  File "./tests/base.py", line 382, in two_nodes_rdmacm_traffic
    raise(res)
AssertionError

Fixes: 926a01dc ("RDMA/hns: Add QP operations support for hip08 SoC")
Link: https://lore.kernel.org/r/20230512092245.344442-2-huangjunxian6@hisilicon.comSigned-off-by: default avatarChengchang Tang <tangchengchang@huawei.com>
Signed-off-by: default avatarJunxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: default avatarJason Gunthorpe <jgg@nvidia.com>
      58caa2a5
    • Yonatan Nachum's avatar
      RDMA/efa: Fix unsupported page sizes in device · 866422cd
      Yonatan Nachum authored 
      Device uses 4KB size blocks for user pages indirect list while the
driver creates those blocks with the size of PAGE_SIZE of the kernel. On
kernels with PAGE_SIZE different than 4KB (ARM RHEL), this leads to a
failure on register MR with indirect list because of the miss
communication between driver and device.

Fixes: 40909f66 ("RDMA/efa: Add EFA verbs implementation")
Link: https://lore.kernel.org/r/20230511115103.13876-1-ynachum@amazon.comReviewed-by: default avatarFiras Jahjah <firasj@amazon.com>
Reviewed-by: default avatarMichael Margolin <mrgolin@amazon.com>
Signed-off-by: default avatarYonatan Nachum <ynachum@amazon.com>
Signed-off-by: default avatarJason Gunthorpe <jgg@nvidia.com>
      866422cd
    • Guoqing Jiang's avatar
      RDMA/rxe: Convert spin_{lock_bh,unlock_bh} to spin_{lock_irqsave,unlock_irqrestore} · b5f3fe27
      Guoqing Jiang authored 
      We need to call spin_lock_irqsave()/spin_unlock_irqrestore() for
state_lock in rxe, otherwsie the callchain:

  ib_post_send_mad
	-> spin_lock_irqsave
	-> ib_post_send -> rxe_post_send
				-> spin_lock_bh
				-> spin_unlock_bh
	-> spin_unlock_irqrestore

Causes below traces during run block nvmeof-mp/001 test due to mismatched
spinlock nesting:

  WARNING: CPU: 0 PID: 94794 at kernel/softirq.c:376 __local_bh_enable_ip+0xc2/0x140
  [ ... ]
  CPU: 0 PID: 94794 Comm: kworker/u4:1 Tainted: G            E      6.4.0-rc1 #9
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.15.0-0-g2dd4b9b-rebuilt.opensuse.org 04/01/2014
  Workqueue: rdma_cm cma_work_handler [rdma_cm]
  RIP: 0010:__local_bh_enable_ip+0xc2/0x140
  Code: 48 85 c0 74 72 5b 41 5c 5d 31 c0 89 c2 89 c1 89 c6 89 c7 41 89 c0 e9 bd 0e 11 01 65 8b 05 f2 65 72 48 85 c0 0f 85 76 ff ff ff <0f> 0b e9 6f ff ff ff e8 d2 39 1c 00 eb 80 4c 89 e7 e8 68 ad 0a 00
  RSP: 0018:ffffb7cf818539f0 EFLAGS: 00010046
  RAX: 0000000000000000 RBX: 0000000000000201 RCX: 0000000000000000
  RDX: 0000000000000000 RSI: 0000000000000201 RDI: ffffffffc0f25f79
  RBP: ffffb7cf81853a00 R08: 0000000000000000 R09: 0000000000000000
  R10: 0000000000000000 R11: 0000000000000000 R12: ffffffffc0f25f79
  R13: ffff8db1f0fa6000 R14: ffff8db2c63ff000 R15: 00000000000000e8
  FS:  0000000000000000(0000) GS:ffff8db33bc00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000559758db0f20 CR3: 0000000105124000 CR4: 00000000003506f0
  Call Trace:
   <TASK>
   _raw_spin_unlock_bh+0x31/0x40
   rxe_post_send+0x59/0x8b0 [rdma_rxe]
   ib_send_mad+0x26b/0x470 [ib_core]
   ib_post_send_mad+0x150/0xb40 [ib_core]
   ? cm_form_tid+0x5b/0x90 [ib_cm]
   ib_send_cm_req+0x7c8/0xb70 [ib_cm]
   rdma_connect_locked+0x433/0x940 [rdma_cm]
   nvme_rdma_cm_handler+0x5d7/0x9c0 [nvme_rdma]
   cma_cm_event_handler+0x4f/0x170 [rdma_cm]
   cma_work_handler+0x6a/0xe0 [rdma_cm]
   process_one_work+0x2a9/0x580
   worker_thread+0x52/0x3f0
   ? __pfx_worker_thread+0x10/0x10
   kthread+0x109/0x140
   ? __pfx_kthread+0x10/0x10
   ret_from_fork+0x2c/0x50
   </TASK>


  raw_local_irq_restore() called with IRQs enabled
  WARNING: CPU: 0 PID: 94794 at kernel/locking/irqflag-debug.c:10 warn_bogus_irq_restore+0x37/0x60
  [ ... ]
  CPU: 0 PID: 94794 Comm: kworker/u4:1 Tainted: G        W   E      6.4.0-rc1 #9
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.15.0-0-g2dd4b9b-rebuilt.opensuse.org 04/01/2014
  Workqueue: rdma_cm cma_work_handler [rdma_cm]
  RIP: 0010:warn_bogus_irq_restore+0x37/0x60
  Code: fb 01 77 36 83 e3 01 74 0e 48 8b 5d f8 c9 31 f6 89 f7 e9 ac ea 01 00 48 c7 c7 e0 52 33 b9 c6 05 bb 1c 69 01 01 e8 39 24 f0 fe <0f> 0b 48 8b 5d f8 c9 31 f6 89 f7 e9 89 ea 01 00 0f b6 f3 48 c7 c7
  RSP: 0018:ffffb7cf81853a58 EFLAGS: 00010246
  RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
  RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
  RBP: ffffb7cf81853a60 R08: 0000000000000000 R09: 0000000000000000
  R10: 0000000000000000 R11: 0000000000000000 R12: ffff8db2cfb1a9e8
  R13: ffff8db2cfb1a9d8 R14: ffff8db2c63ff000 R15: 0000000000000000
  FS:  0000000000000000(0000) GS:ffff8db33bc00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000559758db0f20 CR3: 0000000105124000 CR4: 00000000003506f0
  Call Trace:
   <TASK>
   _raw_spin_unlock_irqrestore+0x91/0xa0
   ib_send_mad+0x1e3/0x470 [ib_core]
   ib_post_send_mad+0x150/0xb40 [ib_core]
   ? cm_form_tid+0x5b/0x90 [ib_cm]
   ib_send_cm_req+0x7c8/0xb70 [ib_cm]
   rdma_connect_locked+0x433/0x940 [rdma_cm]
   nvme_rdma_cm_handler+0x5d7/0x9c0 [nvme_rdma]
   cma_cm_event_handler+0x4f/0x170 [rdma_cm]
   cma_work_handler+0x6a/0xe0 [rdma_cm]
   process_one_work+0x2a9/0x580
   worker_thread+0x52/0x3f0
   ? __pfx_worker_thread+0x10/0x10
   kthread+0x109/0x140
   ? __pfx_kthread+0x10/0x10
   ret_from_fork+0x2c/0x50
   </TASK>

Fixes: f605f26e ("RDMA/rxe: Protect QP state with qp->state_lock")
Link: https://lore.kernel.org/r/20230510035056.881196-1-guoqing.jiang@linux.devSigned-off-by: default avatarGuoqing Jiang <guoqing.jiang@linux.dev>
Reviewed-by: default avatarBob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: default avatarJason Gunthorpe <jgg@nvidia.com>
      b5f3fe27
  7. 16 May, 2023 1 commit
  9. 12 May, 2023 2 commits
  11. 07 May, 2023 8 commits
    • Linus Torvalds's avatar
      Linux 6.4-rc1 · ac9a7868
      Linus Torvalds authored
      ac9a7868
    • Linus Torvalds's avatar
      Merge tag 'perf-tools-for-v6.4-3-2023-05-06' of... · f085df1b
      Linus Torvalds authored 
      Merge tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tool updates from Arnaldo Carvalho de Melo:
 "Third version of perf tool updates, with the build problems with with
  using a 'vmlinux.h' generated from the main build fixed, and the bpf
  skeleton build disabled by default.

  Build:

   - Require libtraceevent to build, one can disable it using
     NO_LIBTRACEEVENT=1.

     It is required for tools like 'perf sched', 'perf kvm', 'perf
     trace', etc.

     libtraceevent is available in most distros so installing
     'libtraceevent-devel' should be a one-time event to continue
     building perf as usual.

     Using NO_LIBTRACEEVENT=1 produces tooling that is functional and
     sufficient for lots of users not interested in those libtraceevent
     dependent features.

   - Allow Python support in 'perf script' when libtraceevent isn't
     linked, as not all features requires it, for instance Intel PT does
     not use tracepoints.

   - Error if the python interpreter needed for jevents to work isn't
     available and NO_JEVENTS=1 isn't set, preventing a build without
     support for JSON vendor events, which is a rare but possible
     condition. The two check error messages:

        $(error ERROR: No python interpreter needed for jevents generation. Install python or build with NO_JEVENTS=1.)
        $(error ERROR: Python interpreter needed for jevents generation too old (older than 3.6). Install a newer python or build with NO_JEVENTS=1.)

   - Make libbpf 1.0 the minimum required when building with out of
     tree, distro provided libbpf.

   - Use libsdtc++'s and LLVM's libcxx's __cxa_demangle, a portable C++
     demangler, add 'perf test' entry for it.

   - Make binutils libraries opt in, as distros disable building with it
     due to licensing, they were used for C++ demangling, for instance.

   - Switch libpfm4 to opt-out rather than opt-in, if libpfm-devel (or
     equivalent) isn't installed, we'll just have a build warning:

       Makefile.config:1144: libpfm4 not found, disables libpfm4 support. Please install libpfm4-dev

   - Add a feature test for scandirat(), that is not implemented so far
     in musl and uclibc, disabling features that need it, such as
     scanning for tracepoints in /sys/kernel/tracing/events.

  perf BPF filters:

   - New feature where BPF can be used to filter samples, for instance:

      $ sudo ./perf record -e cycles --filter 'period > 1000' true
      $ sudo ./perf script
           perf-exec 2273949 546850.708501:       5029 cycles:  ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
           perf-exec 2273949 546850.708508:      32409 cycles:  ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
           perf-exec 2273949 546850.708526:     143369 cycles:  ffffffff82b4cdbf xas_start+0x5f ([kernel.kallsyms])
           perf-exec 2273949 546850.708600:     372650 cycles:  ffffffff8286b8f7 __pagevec_lru_add+0x117 ([kernel.kallsyms])
           perf-exec 2273949 546850.708791:     482953 cycles:  ffffffff829190de __mod_memcg_lruvec_state+0x4e ([kernel.kallsyms])
                true 2273949 546850.709036:     501985 cycles:  ffffffff828add7c tlb_gather_mmu+0x4c ([kernel.kallsyms])
                true 2273949 546850.709292:     503065 cycles:      7f2446d97c03 _dl_map_object_deps+0x973 (/usr/lib/x86_64-linux-gnu/ld-linux-x86-64.so.2)

   - In addition to 'period' (PERF_SAMPLE_PERIOD), the other
     PERF_SAMPLE_ can be used for filtering, and also some other sample
     accessible values, from tools/perf/Documentation/perf-record.txt:

        Essentially the BPF filter expression is:

        <term> <operator> <value> (("," | "||") <term> <operator> <value>)*

     The <term> can be one of:
        ip, id, tid, pid, cpu, time, addr, period, txn, weight, phys_addr,
        code_pgsz, data_pgsz, weight1, weight2, weight3, ins_lat, retire_lat,
        p_stage_cyc, mem_op, mem_lvl, mem_snoop, mem_remote, mem_lock,
        mem_dtlb, mem_blk, mem_hops

     The <operator> can be one of:
        ==, !=, >, >=, <, <=, &

     The <value> can be one of:
        <number> (for any term)
        na, load, store, pfetch, exec (for mem_op)
        l1, l2, l3, l4, cxl, io, any_cache, lfb, ram, pmem (for mem_lvl)
        na, none, hit, miss, hitm, fwd, peer (for mem_snoop)
        remote (for mem_remote)
        na, locked (for mem_locked)
        na, l1_hit, l1_miss, l2_hit, l2_miss, any_hit, any_miss, walk, fault (for mem_dtlb)
        na, by_data, by_addr (for mem_blk)
        hops0, hops1, hops2, hops3 (for mem_hops)

  perf lock contention:

   - Show lock type with address.

   - Track and show mmap_lock, siglock and per-cpu rq_lock with address.
     This is done for mmap_lock by following the current->mm pointer:

      $ sudo ./perf lock con -abl -- sleep 10
       contended   total wait     max wait     avg wait            address   symbol
       ...
           16344    312.30 ms      2.22 ms     19.11 us   ffff8cc702595640
           17686    310.08 ms      1.49 ms     17.53 us   ffff8cc7025952c0
               3     84.14 ms     45.79 ms     28.05 ms   ffff8cc78114c478   mmap_lock
            3557     76.80 ms     68.75 us     21.59 us   ffff8cc77ca3af58
               1     68.27 ms     68.27 ms     68.27 ms   ffff8cda745dfd70
               9     54.53 ms      7.96 ms      6.06 ms   ffff8cc7642a48b8   mmap_lock
           14629     44.01 ms     60.00 us      3.01 us   ffff8cc7625f9ca0
            3481     42.63 ms    140.71 us     12.24 us   ffffffff937906ac   vmap_area_lock
           16194     38.73 ms     42.15 us      2.39 us   ffff8cd397cbc560
              11     38.44 ms     10.39 ms      3.49 ms   ffff8ccd6d12fbb8   mmap_lock
               1      5.43 ms      5.43 ms      5.43 ms   ffff8cd70018f0d8
            1674      5.38 ms    422.93 us      3.21 us   ffffffff92e06080   tasklist_lock
             581      4.51 ms    130.68 us      7.75 us   ffff8cc9b1259058
               5      3.52 ms      1.27 ms    703.23 us   ffff8cc754510070
             112      3.47 ms     56.47 us     31.02 us   ffff8ccee38b3120
             381      3.31 ms     73.44 us      8.69 us   ffffffff93790690   purge_vmap_area_lock
             255      3.19 ms     36.35 us     12.49 us   ffff8d053ce30c80

   - Update default map size to 16384.

   - Allocate single letter option -M for --map-nr-entries, as it is
     proving being frequently used.

   - Fix struct rq lock access for older kernels with BPF's CO-RE
     (Compile once, run everywhere).

   - Fix problems found with MSAn.

  perf report/top:

   - Add inline information when using --call-graph=fp or lbr, as was
     already done to the --call-graph=dwarf callchain mode.

   - Improve the 'srcfile' sort key performance by really using an
     optimization introduced in 6.2 for the 'srcline' sort key that
     avoids calling addr2line for comparision with each sample.

  perf sched:

   - Make 'perf sched latency/map/replay' to use "sched:sched_waking"
     instead of "sched:sched_waking", consistent with 'perf record'
     since d566a9c2 ("perf sched: Prefer sched_waking event when it
     exists").

  perf ftrace:

   - Make system wide the default target for latency subcommand, run the
     following command then generate some network traffic and press
     control+C:

       # perf ftrace latency -T __kfree_skb
     ^C
         DURATION     |      COUNT | GRAPH                                          |
          0 - 1    us |         27 | #############                                  |
          1 - 2    us |         22 | ###########                                    |
          2 - 4    us |          8 | ####                                           |
          4 - 8    us |          5 | ##                                             |
          8 - 16   us |         24 | ############                                   |
         16 - 32   us |          2 | #                                              |
         32 - 64   us |          1 |                                                |
         64 - 128  us |          0 |                                                |
        128 - 256  us |          0 |                                                |
        256 - 512  us |          0 |                                                |
        512 - 1024 us |          0 |                                                |
          1 - 2    ms |          0 |                                                |
          2 - 4    ms |          0 |                                                |
          4 - 8    ms |          0 |                                                |
          8 - 16   ms |          0 |                                                |
         16 - 32   ms |          0 |                                                |
         32 - 64   ms |          0 |                                                |
         64 - 128  ms |          0 |                                                |
        128 - 256  ms |          0 |                                                |
        256 - 512  ms |          0 |                                                |
        512 - 1024 ms |          0 |                                                |
          1 - ...   s |          0 |                                                |
       #

  perf top:

   - Add --branch-history (LBR: Last Branch Record) option, just like
     already available for 'perf record'.

   - Fix segfault in thread__comm_len() where thread->comm was being
     used outside thread->comm_lock.

  perf annotate:

   - Allow configuring objdump and addr2line in ~/.perfconfig., so that
     you can use alternative binaries, such as llvm's.

  perf kvm:

   - Add TUI mode for 'perf kvm stat report'.

  Reference counting:

   - Add reference count checking infrastructure to check for use after
     free, done to the 'cpumap', 'namespaces', 'maps' and 'map' structs,
     more to come.

     To build with it use -DREFCNT_CHECKING=1 in the make command line
     to build tools/perf. Documented at:

       https://perf.wiki.kernel.org/index.php/Reference_Count_Checking

   - The above caught, for instance, fix, present in this series:

        - Fix maps use after put in 'perf test "Share thread maps"':

          'maps' is copied from leader, but the leader is put on line 79
          and then 'maps' is used to read the reference count below - so
          a use after put, with the put of maps happening within
          thread__put.

     Fixed by reversing the order of puts so that the leader is put
     last.

   - Also several fixes were made to places where reference counts were
     not being held.

   - Make this one of the tests in 'make -C tools/perf build-test' to
     regularly build test it and to make sure no direct access to the
     reference counted structs are made, doing that via accessors to
     check the validity of the struct pointer.

  ARM64:

   - Fix 'perf report' segfault when filtering coresight traces by
     sparse lists of CPUs.

   - Add support for 'simd' as a sort field for 'perf report', to show
     ARM's NEON SIMD's predicate flags: "partial" and "empty".

  arm64 vendor events:

   - Add N1 metrics.

  Intel vendor events:

   - Add graniterapids, grandridge and sierraforrest events.

   - Refresh events for: alderlake, aldernaken, broadwell, broadwellde,
     broadwellx, cascadelakx, haswell, haswellx, icelake, icelakex,
     jaketown, meteorlake, knightslanding, sandybridge, sapphirerapids,
     silvermont, skylake, tigerlake and westmereep-dp

   - Refresh metrics for alderlake-n, broadwell, broadwellde,
     broadwellx, haswell, haswellx, icelakex, ivybridge, ivytown and
     skylakex.

  perf stat:

   - Implement --topdown using JSON metrics.

   - Add TopdownL1 JSON metric as a default if present, but disable it
     for now for some Intel hybrid architectures, a series of patches
     addressing this is being reviewed and will be submitted for v6.5.

   - Use metrics for --smi-cost.

   - Update topdown documentation.

  Vendor events (JSON) infrastructure:

   - Add support for computing and printing metric threshold values. For
     instance, here is one found in thesapphirerapids json file:

       {
           "BriefDescription": "Percentage of cycles spent in System Management Interrupts.",
           "MetricExpr": "((msr@aperf@ - cycles) / msr@aperf@ if msr@smi@ > 0 else 0)",
           "MetricGroup": "smi",
           "MetricName": "smi_cycles",
           "MetricThreshold": "smi_cycles > 0.1",
           "ScaleUnit": "100%"
       },

   - Test parsing metric thresholds with the fake PMU in 'perf test
     pmu-events'.

   - Support for printing metric thresholds in 'perf list'.

   - Add --metric-no-threshold option to 'perf stat'.

   - Add rand (reverse and) and has_pmem (optane memory) support to
     metrics.

   - Sort list of input files to avoid depending on the order from
     readdir() helping in obtaining reproducible builds.

  S/390:

   - Add common metrics: - CPI (cycles per instruction), prbstate (ratio
     of instructions executed in problem state compared to total number
     of instructions), l1mp (Level one instruction and data cache misses
     per 100 instructions).

   - Add cache metrics for z13, z14, z15 and z16.

   - Add metric for TLB and cache.

  ARM:

   - Add raw decoding for SPE (Statistical Profiling Extension) v1.3 MTE
     (Memory Tagging Extension) and MOPS (Memory Operations) load/store.

  Intel PT hardware tracing:

   - Add event type names UINTR (User interrupt delivered) and UIRET
     (Exiting from user interrupt routine), documented in table 32-50
     "CFE Packet Type and Vector Fields Details" in the Intel Processor
     Trace chapter of The Intel SDM Volume 3 version 078.

   - Add support for new branch instructions ERETS and ERETU.

   - Fix CYC timestamps after standalone CBR

  ARM CoreSight hardware tracing:

   - Allow user to override timestamp and contextid settings.

   - Fix segfault in dso lookup.

   - Fix timeless decode mode detection.

   - Add separate decode paths for timeless and per-thread modes.

  auxtrace:

   - Fix address filter entire kernel size.

  Miscellaneous:

   - Fix use-after-free and unaligned bugs in the PLT handling routines.

   - Use zfree() to reduce chances of use after free.

   - Add missing 0x prefix for addresses printed in hexadecimal in 'perf
     probe'.

   - Suppress massive unsupported target platform errors in the unwind
     code.

   - Fix return incorrect build_id size in elf_read_build_id().

   - Fix 'perf scripts intel-pt-events.py' IPC output for Python 2 .

   - Add missing new parameter in kfree_skb tracepoint to the python
     scripts using it.

   - Add 'perf bench syscall fork' benchmark.

   - Add support for printing PERF_MEM_LVLNUM_UNC (Uncached access) in
     'perf mem'.

   - Fix wrong size expectation for perf test 'Setup struct
     perf_event_attr' caused by the patch adding
     perf_event_attr::config3.

   - Fix some spelling mistakes"

* tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (365 commits)
  Revert "perf build: Make BUILD_BPF_SKEL default, rename to NO_BPF_SKEL"
  Revert "perf build: Warn for BPF skeletons if endian mismatches"
  perf metrics: Fix SEGV with --for-each-cgroup
  perf bpf skels: Stop using vmlinux.h generated from BTF, use subset of used structs + CO-RE
  perf stat: Separate bperf from bpf_profiler
  perf test record+probe_libc_inet_pton: Fix call chain match on x86_64
  perf test record+probe_libc_inet_pton: Fix call chain match on s390
  perf tracepoint: Fix memory leak in is_valid_tracepoint()
  perf cs-etm: Add fix for coresight trace for any range of CPUs
  perf build: Fix unescaped # in perf build-test
  perf unwind: Suppress massive unsupported target platform errors
  perf script: Add new parameter in kfree_skb tracepoint to the python scripts using it
  perf script: Print raw ip instead of binary offset for callchain
  perf symbols: Fix return incorrect build_id size in elf_read_build_id()
  perf list: Modify the warning message about scandirat(3)
  perf list: Fix memory leaks in print_tracepoint_events()
  perf lock contention: Rework offset calculation with BPF CO-RE
  perf lock contention: Fix struct rq lock access
  perf stat: Disable TopdownL1 on hybrid
  perf stat: Avoid SEGV on counter->name
  ...
      f085df1b
    • Linus Torvalds's avatar
      Merge tag 'core-debugobjects-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip · 17784de6
      Linus Torvalds authored 
      Pull debugobjects fix from Thomas Gleixner:
 "A single fix for debugobjects:

  The recent fix to ensure atomicity of lookup and allocation
  inadvertently broke the pool refill mechanism, so that debugobject
  OOMs now in certain situations. The reason is that the functions which
  got updated no longer invoke debug_objecs_init(), which is now the
  only place to care about refilling the tracking object pool.

  Restore the original behaviour by adding explicit refill opportunities
  to those places"

* tag 'core-debugobjects-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  debugobject: Ensure pool refill (again)
      17784de6
    • Linus Torvalds's avatar
      Merge tag 'v6.4-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 · 6f69c981
      Linus Torvalds authored 
      Pull crypto fixes from Herbert Xu:

 - A long-standing bug in crypto_engine

 - A buggy but harmless check in the sun8i-ss driver

 - A regression in the CRYPTO_USER interface

* tag 'v6.4-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: api - Fix CRYPTO_USER checks for report function
  crypto: engine - fix crypto_queue backlog handling
  crypto: sun8i-ss - Fix a test in sun8i_ss_setup_ivs()
      6f69c981
    • Linus Torvalds's avatar
      Merge tag '6.4-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6 · 63342b1d
      Linus Torvalds authored 
      Pull cifs fixes from Steve French:
 "smb3 client fixes, mostly DFS or reconnect related:

   - Two DFS connection sharing fixes

   - DFS refresh fix

   - Reconnect fix

   - Two potential use after free fixes

   - Also print prefix patch in mount debug msg

   - Two small cleanup fixes"

* tag '6.4-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Remove unneeded semicolon
  cifs: fix sharing of DFS connections
  cifs: avoid potential races when handling multiple dfs tcons
  cifs: protect access of TCP_Server_Info::{origin,leaf}_fullpath
  cifs: fix potential race when tree connecting ipc
  cifs: fix potential use-after-free bugs in TCP_Server_Info::hostname
  cifs: print smb3_fs_context::source when mounting
  cifs: protect session status check in smb2_reconnect()
  SMB3.1.1: correct definition for app_instance_id create contexts
      63342b1d
    • Linus Torvalds's avatar
      Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux · d6b8a8c4
      Linus Torvalds authored 
      Pull clk fixes from Stephen Boyd:
 "A couple more patches that would be good to get into -rc1:

   - Revert an i.MX patch that's causing video failures because division
     math goes sideways

   - Fix a clang + W=1 build isue where FIELD_PREP() is taking a 32-bit
     variable instead of the usual u64 type

   - Fix a Kconfig bug in the StarFive JH7110 clk config that selects a
     reset controller when it can't be selected"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: starfive: Fix RESET_STARFIVE_JH7110 can't be selected in a specified case
  clk: sp7021: Adjust width of _m in HWM_FIELD_PREP()
  Revert "clk: imx: composite-8m: Add support to determine_rate"
      d6b8a8c4
    • Linus Torvalds's avatar
      Merge tag 'mailbox-v6.4' of git://git.linaro.org/landing-teams/working/fujitsu/integration · 1c1094e4
      Linus Torvalds authored 
      Pull mailbox updates from Jassi Brar:

 - mailbox api: allow direct registration to a channel and convert omap
   and pcc to use mbox_bind_client

 - omap and hi6220 : use of_property_read_bool

 - test: fix double-free and use spinlock header

 - rockchip and bcm-pdc: drop of_match_ptr

 - mpfs: change config symbol

 - mediatek gce: support MT6795

 - qcom apcs: consolidate of_device_id and support IPQ9574

* tag 'mailbox-v6.4' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
  dt-bindings: mailbox: qcom: add compatible for IPQ9574 SoC
  mailbox: qcom-apcs-ipc: do not grow the of_device_id
  dt-bindings: mailbox: qcom,apcs-kpss-global: use fallbacks for few variants
  dt-bindings: mailbox: mediatek,gce-mailbox: Add support for MT6795
  mailbox: mpfs: convert SOC_MICROCHIP_POLARFIRE to ARCH_MICROCHIP_POLARFIRE
  mailbox: bcm-pdc: drop of_match_ptr for ID table
  mailbox: rockchip: drop of_match_ptr for ID table
  mailbox: mailbox-test: Fix potential double-free in mbox_test_message_write()
  mailbox: mailbox-test: Explicitly include header for spinlock support
  mailbox: Use of_property_read_bool() for boolean properties
  mailbox: pcc: Use mbox_bind_client
  mailbox: omap: Use mbox_bind_client
  mailbox: Allow direct registration to a channel
      1c1094e4
    • Linus Torvalds's avatar
      Merge tag 'for-6.4/io_uring-2023-05-07' of git://git.kernel.dk/linux · 03e5cb7b
      Linus Torvalds authored 
      Pull more io_uring updates from Jens Axboe:
 "Nothing major in here, just two different parts:

   - A small series from Breno that enables passing the full SQE down
     for ->uring_cmd().

     This is a prerequisite for enabling full network socket operations.
     Queued up a bit late because of some stylistic concerns that got
     resolved, would be nice to have this in 6.4-rc1 so the dependent
     work will be easier to handle for 6.5.

   - Fix for the huge page coalescing, which was a regression introduced
     in the 6.3 kernel release (Tobias)"

* tag 'for-6.4/io_uring-2023-05-07' of git://git.kernel.dk/linux:
  io_uring: Remove unnecessary BUILD_BUG_ON
  io_uring: Pass whole sqe to commands
  io_uring: Create a helper to return the SQE size
  io_uring/rsrc: check for nonconsecutive pages
      03e5cb7b
  13. 06 May, 2023 18 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7