The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines
of optically-isolated non-polarized digital inputs for AC and DC control
signals, 24 lines of isolated solid state FET digital outputs, and 8
non-isolated TTL/CMOS compatible programmable I/O). An interrupt is
generated when any of the inputs change state (low to high or high to
low).

Input filter control is not supported by this driver, and input filters
are deactivated by this driver. These devices are capable of
get_multiple and set_multiple functionality, but these functions have
not yet been implemented for this driver. Change-Of-State (COS)
detection functionality may be configured to fire interrupts on
exclusively rising/falling edges, but this driver currently only
implements COS detection for either both edges or none.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some pinctrl drivers can use the gpiochip irq valid information
to figure out if certain gpios are exposed to the kernel for
usage or not. Expose this API so we can use it in the
pinmux_ops::request ops.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The use of the GPIOF_* flags is deprecated, so don't advertise them
here. Document the plain numbers for now until we have a better
solution.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The use of the GPIOF_* flags is deprecated, so don't advertise them
here. Document the plain numbers for now until we have a better
solution.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This commit adds GPIO driver for Winbond Super I/Os.

Currently, only W83627UHG model (also known as Nuvoton NCT6627UD)
is supported but in the future a support for other Winbond models,
too, can be added to the driver.

A module parameter "gpios" sets a bitmask of GPIO ports to enable
(bit 0 is GPIO1, bit 1 is GPIO2, etc.).

One should be careful which ports one tinkers with since some
might be managed by the firmware (for functions like powering on and
off, sleeping, BIOS recovery, etc.) and some of GPIO port pins are
physically shared with other devices included in the Super I/O chip.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Before it was clearly established that all GPIO properties in the
device tree shall be named "foo-gpios" (with the deprecated variant
"foo-gpio" for single lines) we unfortunately merged a few bindings
which named the lines "gpio-foo" instead.

This is most prominent in the GPIO SPI driver in Linux which names
the lines "gpio-sck", "gpio-mosi" and "gpio-miso".

As we want to switch the GPIO SPI driver to using descriptors, we
need devm_gpiod_get() to return something reasonable when looking
up these in the device tree.

Put in a special #ifdef:ed kludge to do this special lookup only
for the SPI case and gets compiled out if we're not enabling SPI.
If we have more oddly defined legacy GPIOs like this, they can be
handled in a similar manner.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some GPIO lines appear named "?" in the lsgpio dump due to their
requesting drivers not passing a reasonable label.

Most typically this happens if a device tree node just defines
gpios = <...> and not foo-gpios = <...>, the former gets named
"foo" and the latter gets named "?".

However the struct device passed in is always valid so let's
just label the GPIO with dev_name() on the device if no proper
label was passed.

Cc: Reported-by: Jason Kridner <jkridner@beagleboard.org>
Reported-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As we need to add GPIO lookup tables to the OMAP platforms, we
need to reference each GPIO chip with a unique label. Use the GPIO
base to name each chip, "gpio-0-31", "gpio-32-63" etc.

Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The gpiod_set_transitory() function is publicly exported, and
it is expected from it to be ready for usage with optional GPIOs
on consumer's side.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This non-functional change slightly simplifies the implementation
of gpiod_to_chip() function.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The fix restores a proper validation of an input gpio desc, which
might be needed to deal with optional GPIOs correctly.

Fixes: 02e47980 ("gpio: Alter semantics of *raw* operations to actually be raw")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The test should be >= ARRAY_SIZE() instead of > ARRAY_SIZE().
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This reverts commit 93ebe863.

After discussion and review of the v11 patchset, a new approach
was found so that this patch is not needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

While we do need macros to be able to return from the "calling"
function, we can still factor the checks done by the VALIDATE_DESC*
macros into a real helper function. This reduces the backslashtitis,
avoids duplicating the logic in the two macros and saves about 1K of
generated code:

$ scripts/bloat-o-meter drivers/gpio/gpiolib.o.{0,1}
add/remove: 1/0 grow/shrink: 0/15 up/down: 104/-1281 (-1177)
Function                                     old     new   delta
validate_desc                                  -     104    +104
gpiod_set_value                              192     135     -57
gpiod_set_raw_value                          125      67     -58
gpiod_direction_output                       412     351     -61
gpiod_set_value_cansleep                     150      70     -80
gpiod_set_raw_value_cansleep                 132      52     -80
gpiod_get_raw_value                          139      54     -85
gpiod_set_debounce                           226     140     -86
gpiod_direction_output_raw                   124      38     -86
gpiod_get_value                              161      74     -87
gpiod_cansleep                               126      39     -87
gpiod_get_raw_value_cansleep                 130      39     -91
gpiod_get_value_cansleep                     152      59     -93
gpiod_is_active_low                          128      33     -95
gpiod_request                                299     184    -115
gpiod_direction_input                        386     266    -120
Total: Before=25460, After=24283, chg -4.62%
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The GPIO tools build fails when using a buildroot toolchain that uses musl
as it's C library:

arm-broomstick-linux-musleabi-gcc -Wp,-MD,./.gpio-event-mon.o.d \
 -Wp,-MT,gpio-event-mon.o -O2 -Wall -g -D_GNU_SOURCE \
 -Iinclude -D"BUILD_STR(s)=#s" -c -o gpio-event-mon.o gpio-event-mon.c
gpio-event-mon.c:30:6: error: unknown type name ‘u_int32_t’; did you mean ‘uint32_t’?
      u_int32_t handleflags,
      ^~~~~~~~~
      uint32_t

The glibc headers installed on my laptop include sys/types.h in
unistd.h, but it appears that musl does not.

Fixes: 97f69747 ("tools/gpio: add the gpio-event-mon tool")
Cc: stable@vger.kernel.org
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl-msm only accepts an array of GPIOs from 0 to n-1, and it expects
each group to support have only one pin (npins == 1).

We can support "sparse" GPIO maps if we allow for some groups to have zero
pins (npins == 0).  These pins are "hidden" from the rest of the driver
and gpiolib.

Access to unavailable GPIOs is blocked via a request callback.  If the
requested GPIO is unavailable, -EACCES is returned, which prevents
further access to that GPIO.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This reverts commit 72d32000.

We cannot blindly query the direction of all GPIOs when the pins are
first registered.  The get_direction callback normally triggers a
read/write to hardware, but we shouldn't be touching the hardware for
an individual GPIO until after it's been properly claimed.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

R8A7778 is R-Car (not R-Mobile) M1.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These duplicate includes have been found with scripts/checkincludes.pl
but they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

u_int32_t is a non-standard version of uint32_t, that was apparently
introduced by BSD. Use uint32_t from stdint.h instead.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

A 'perf record' on an app continuously writing in the 'value'
attribute show that most of the time is spent in kstrtol()

--17.99%--value_store
          |
          |--10.17%--kstrtoint
          |          |
          |          |--8.82%--kstrtoll
          |
          |--2.50%--gpiod_set_value_cansleep
          |
          |--1.82%--u16_gpio_set
          |
          |--1.46%--value_store

The normal case is to write 0 or 1 in the attribute, therefore
this patch avoids the call to kstrtol() in the most common cases

Then 'perf record' shows

--7.21%--value_store
          |
          |--2.69%--u16_gpio_set
          |
          |--1.47%--value_store
          |
          |--1.08%--gpiod_set_value_cansleep
          |
          |--0.60%--mutex_lock
          |
           --0.58%--mutex_unlock
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

A bench with 'perf record' shows that most of time spent in value_show()
is spent in sprintf()

--42.41%--sysfs_kf_read
          |
          |--39.73%--dev_attr_show
          |          |
          |          |--38.23%--value_show
          |          |          |
          |          |          |--29.22%--sprintf
          |          |          |
          |          |          |--2.94%--gpiod_get_value_cansleep
          |          |          |

value_show() only returns "0\n" or "1\n", therefore the use of
sprintf() can be avoided

With this patch we get the following result with 'perf record'

--13.89%--sysfs_kf_read
          |
          |--10.72%--dev_attr_show
          |          |
          |          |--9.44%--value_show
          |          |          |
          |          |          |--4.61%--gpiod_get_value_cansleep
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

'value' attribute is supposed to only return 0 or 1 according to
the documentation.
With today's implementation, if gpiod_get_value_cansleep() fails
the printed 'value' is a negative value.

This patch ensures that an error is returned on read instead.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The GPIO 'value' attribute is time critical. A small bench with
'perf record' on the app below shows that 80% of the time spent in
sysfs_kf_seq_show() is spent in memset() for zeroising the buffer.

|--67.48%--sysfs_kf_seq_show
|          |
|          |--54.40%--memset
|          |
|          |--11.49%--dev_attr_show
|          |          |
|          |          |--10.06%--value_show
|          |          |          |
|          |          |          |--4.75%--sprintf
|          |          |          |          |

This patch changes the attribute type to prealloc, eliminating the
need to zeroise the buffer at each read. 'perf record' gives the
following result.

|--42.41%--sysfs_kf_read
|          |
|          |--39.73%--dev_attr_show
|          |          |
|          |          |--38.23%--value_show
|          |          |          |
|          |          |          |--29.22%--sprintf
|          |          |          |          |

Test done with the following small app:

int main(int argc, char **argv)
{
	int fd = open(argv[1], O_RDONLY);

	for (;;) {
		int buf[512];

		read(fd, buf, 512);
		lseek(fd, 0, SEEK_SET);
	}
	exit(0);
}
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Users often pass a pointer to a static string to gpiochip_add_data()
family of functions. Avoid unnecessary memory allocations with the
provided helper routine.

While at it: use a ternary operator instead of an if else for brevity.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This string is never modified. Make it const.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The return value of platform_device_register_resndata() on error is
an error code converted to pointer with ERR_PTR(), not NULL.

Check the return value correctly.

Fixes: 8a39f597 ("gpio: mockup: rework device probing")
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The w1 master driver includes a complete open drain emulation
reimplementation among other things.

This converts the driver and all board files using it to use
GPIO descriptors associated with the device to look up the
GPIO wire, as well ass the optional pull-up GPIO line.

When probed from the device tree, the driver will just pick
descriptors and use them right off. For the two board files
in the kernel, we add descriptor lookups so we do not need
to keep any old platform data handling around for the GPIO
lines.

As the platform data is also a state container for this driver,
we augment it to contain the GPIO descriptors.

w1_gpio_write_bit_dir() and w1_gpio_write_bit_val() are gone
since this pair was a reimplementation of open drain emulation
which is now handled by gpiolib.

The special "linux,open-drain" flag is a bit of mishap here:
it has the same semantic as the same flags in I2C: it means
that something in the platform is setting up the line as
open drain behind our back. We handle this the same way as
in I2C.

To drive the pull-up, we need to bypass open drain emulation
in gpiolib for the line, and this is done by driving it high
using gpiod_set_raw_value() which has been augmented to have
the semantic of overriding the open drain emulation.

We also augment the documentation to reflect the way to pass
GPIO descriptors from the machine.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The AXP813 has only two GPIOs. GPIO0 can either be used as a GPIO, an
LDO regulator or an ADC. GPIO1 can be used either as a GPIO or an LDO
regulator.

Moreover, the status bit of the GPIOs when in input mode is not offset
by 4 unlike the AXP209.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

To prepare for patches that will add support for a new PMIC that has a
different GPIO adc muxing value, add an adc_mux within axp20x_pctl
structure and use it.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

To prepare for patches that will add support for a new PMIC that has a
different GPIO input status register, add a gpio_status_offset within
axp20x_pctl structure and use it.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This driver used to do only GPIO features of the GPIOs in X-Powers
AXP20X. Now that we have migrated everything to the pinctrl subsystem
and added pinctrl features, rename everything related to pinctrl from
gpio to pctl to ease the understanding of differences between GPIO
and pinctrl features.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The X-Powers AXP209 has 3 GPIOs. GPIO0/1 can each act either as a GPIO,
an ADC or a LDO regulator. GPIO2 can only act as a GPIO.

This adds the pinctrl features to the driver so GPIO0/1 can be used as
ADC or LDO regulator.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The X-Powers AXP209 has 3 GPIOs. GPIO0/1 can each act either as a GPIO,
an ADC or a LDO regulator. GPIO2 can only act as a GPIO.

This adds the pinctrl features to the driver so GPIO0/1 can be used as
ADC or LDO regulator.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

To prepare the driver for the upcoming pinctrl features, move the GPIO
driver AXP209 from GPIO to pinctrl subsystem.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Checkpatch complains with the following message:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'

Let's make it happy by switching over to unsigned int.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use the new pinconf parameter for state persistence to expose the
associated capability of the Aspeed GPIO controller.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>