- 10 Apr, 2013 4 commits
-
-
Gabor Juhos authored
The functions in the rt2x00mmio module has been moved from the rt2x00pci module. Each function uses the rt2x00pci prefix which is a bit confusing. Use the r2x000mmio prefix for each function to make it consistent with the module name. The renamed functions are used by several modules, and updating the names in all of them would result in a big patch. In order to keep the patch simple, add compatibility defines for the old function names. This allows to update the names in each module separately. After each module is updated, the defines can be removed. The patch contains no functional changes. Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Acked-by:
Helmut Schaa <helmut.schaa@googlemail.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-nextJohn W. Linville authored
Conflicts: drivers/net/wireless/ath/carl9170/debug.c drivers/net/wireless/ath/carl9170/main.c net/mac80211/ieee80211_i.h
-
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirelessJohn W. Linville authored
Conflicts: drivers/net/wireless/rt2x00/rt2x00pci.c
-
- 08 Apr, 2013 36 commits
-
-
Arend van Spriel authored
In brcmf_rx_frames() the call to brcmf_fweh_process_skb() could change the ifidx using information in the event data. This is only different to the BDC ifidx for IF ADD event. However, the creation of the new interface is deferred to event worker so it does not exist. After brcmf_fweh_process_skb() it is only used to set statistics. Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
The function brcmf_p2p_notify_action_frame_rx() the wireless_dev is needed to pass the action frame to cfg80211. The wireless_dev is held in brcmf_cfg80211_vif object. Use that instead of the ieee80211_ptr in net_device as P2P_DEVICE interface does not have a net_device associated with it. Reviewed-by:
-
Arend van Spriel authored
The probe requests received on P2P_DEVICE interface were not sent to wpa_supplicant, which makes the device not discoverable by peers. Reviewed-by:
-
Arend van Spriel authored
The firmware sends a IF event to notify the host driver that the P2P_DEVICE interface has been created. Wait for the event before returning the related wireless_dev. Reviewed-by:
Piotr Haber <phaber@broadcom.com> Reviewed-by:
-
Arend van Spriel authored
The current driver code creates a P2P_DEVICE through a module parameter. This device has a dummy netdevice which is not how this interface type is intended. This patch add proper support for the P2P_DEVICE interface type. This requires a wpa_supplicant with such support as well. Reviewed-by:
-
Arend van Spriel authored
escan functionality is also required for P2P device operations so it is better not to rely on struct netdevice instances. Reviewed-by:
-
Arend van Spriel authored
Remove use of struct netdevice as parameter to brcmf_set_mpc() as it will not always be available, ie. there will be non-netdevice interfaces. Reviewed-by:
-
Arend van Spriel authored
With the introduction of the P2P_DEVICE interface type an instance of struct wireless_dev does not always have a netdev assigned to it. Better use container_of() construct to obtain internal structure and go from there. Reviewed-by:
-
Arend van Spriel authored
In fweh module the event handler was only called if the struct brcmf_if instance had a non-null netdev associated. This restriction is no longer valid for P2P_DEVICE type of interface. This patch removes that restriction. Reviewed-by:
-
Arend van Spriel authored
According specification the IF event has an additional field indicating the role or type of the interface for which this event is sent. Reviewed-by:
-
Arend van Spriel authored
Adds a trace function used in brcmf_dbg_hex_dump() which adds the raw binary data to the trace. It requires trace-cmd plugin to see this data. Reviewed-by:
-
Piotr Haber authored
Firware shared data structure is backward compatible for fields we are interested in. Allow reading of shared data in case of version mismatch. Reviewed-by:
-
Piotr Haber authored
Firmware console output can be read also when there was no trap indication. Reviewed-by:
-
Arend van Spriel authored
The firmware can request the host driver for packets, by sending either the MAC_REQUEST_CREDIT or the MAC_REQUEST_PACKET primitive. This patch adds handling of these primitives. Reviewed-by:
-
Arend van Spriel authored
Firmware can signal whether the host driver may sent packets for a specific destination or interface. This can happen when a destination is sleeping or when going off-channel. Reviewed-by:
-
Arend van Spriel authored
reported by Hante. Needs to be squashed in commit 187fbcec. Reviewed-by:
-
Andreas Fenkart authored
Not locking ra_list when dequeuing packets creates race conditions. When adding a packet 'tx_pkts_queued' is modified before setting highest_priority_queue. If in-between the main loop starts, it will see a packet queued (tx_pkts_queued > 0) but will not find it, since max prio is not set yet. Depending on the scheduling, the thread trying to add the packet could complete and restore the situation. But this is not something to rely on. Another race condition exists, if a new packet, exceeding current max prio is added. If concurrently a packet is dequeued, the newly set max prio will be overwritten with the value of the dequeued packet. This can occur, because selecting a packet and modifying the max prio is not atomic. The result in an infinite loop unless, a new packet is added that has at least the priority of the hidden packet. Same applies to bss_prio_tbl. Forward iteration is no proper lock-free technique and provides no protection from calls to list_del. Although BSS are currently not added/removed dynamically, this must not be the case in the future. Hence always hold proper locks when accessing those lists. Signed-off-by:
Andreas Fenkart <andreas.fenkart@streamunlimited.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Andreas Fenkart authored
Using NO_PKT_PRIO_TID and tx_pkts_queued to check for an empty state, can lead to a contradictory state, resulting in an infinite loop. Currently queueing and dequeuing of packets is not synchronized, and can happen concurrently. While tx_pkts_queued is incremented when adding a packet, max prio is set to NO_PKT when the WMM list is empty. If a packet is added right after the check for empty, but before setting max prio to NO_PKT, that packet is trapped and creates an infinite loop. Because of the new packet, tx_pkts_queued is at least 1, indicating wmm lists are not empty. Opposing that max prio is NO_PKT, which means "skip this wmm queue, it has no packets". The infinite loop results, because the main loop checks the wmm lists for not empty via tx_pkts_queued, but for dequeing it uses max_prio to see if it can skip current list. This will never end, unless a new packet is added which will restore max prio to the level of the trapped packet. The solution here is to rely on tx_pkts_queued solely for checking wmm queue to be empty, and drop the NO_PKT define. It does not address the locking issue. Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
-
Andreas Fenkart authored
ra_list_spinlock is used to protect struct mwifiex_wmm_desc and embedded structures such as ra_list. tid_tbl_lock while more fine grained, is not used but in one function. That function is not called reentrantly. To protect ra_list from concurrent modification ra_list_spinlock must be held. Signed-off-by:
-
Andreas Fenkart authored
adapter->bss_prio_tbl list has already been checked in outer loop. The inner loop works with priv_tmp->wmm.tid_tbl_ptr list. Also the lock taken, gives hint that this is likely a copy-paste error. Signed-off-by:
-
Larry Finger authored
An allyesconfig build of rtl8188ee yields the following duplicate entry points: drivers/net/wireless/rtlwifi/rtl8188ee/built-in.o: In function `.rtl92c_phy_ap_calibrate': (.text+0x21d14): multiple definition of `.rtl92c_phy_ap_calibrate' drivers/net/wireless/rtlwifi/rtl8192c/built-in.o:(.text+0xb1e8): first defined here drivers/net/wireless/rtlwifi/rtl8188ee/built-in.o: In function `rtl_hal_pwrseqcmdparsing': (.opd+0xed0): multiple definition of `rtl_hal_pwrseqcmdparsing' One of the routines is not used and can be deleted, the other is renamed. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
Larry Finger authored
Building rtl8188ee yields warnings such as the following: x86_64-linux-gcc: warning: drivers/net/wireless/rtlwifi: linker input file unused because linking not done The only potential cause is an extraneous space in the make file. Signed-off-by:
-
Zefir Kurtisi authored
These are the remaining knobs in ath9k to support DFS: * mark AR9280 and AR9580 as DFS tested * synchronize DFS regulatory domain to reg notifyer * set required RX filter flags for radar detection * process radar PHY errors at DFS detector * notify DFS master on radar detection DFS support requires CONFIG_ATH9K_DFS_CERTIFIED to be set. Signed-off-by:
Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by:
-
Zefir Kurtisi authored
This helps testing DFS without radar generating equipment and is required for certification. Signed-off-by:
Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by:
-
Zefir Kurtisi authored
Signed-off-by:
-
Ben Greear authored
Should make the warning messages more useful. Signed-off-by:
Ben Greear <greearb@candelatech.com> Signed-off-by:
-
Bing Zhao authored
cmd_pending is increased in mwifiex_wait_queue_complete() and decreased in mwifiex_complete_cmd() currently. If there are two or more commands in the cmd_pending_q the main worker thread will pick up next command from cmd_pending_q automatically after finishing current command. As a result mwifiex_wait_queue_complete() will not be called because the command is alreay completed. This leads to a negative number in cmd_pending count. Fix it by increasing cmd_pending when a cmd is queued into cmd_pending_q and decreasing when that cmd is recycled. For scan commands we don't perform inc/dec operations until it's moved from scan_pending_q to cmd_pending_q. This covers both synchronous and asynchronous commands. Reported-by:
Daniel Drake <dsd@laptop.org> Tested-by:
Marco Cesarano <marco@marvell.com> Signed-off-by:
-
Emmanuel Grumbach authored
Until now we didn't handle properly the FLUSH ampdu action coming from mac80211. This could result in SCD queue leak: mac80211 would STOP_FLUSH an AMPDU Tx session and remove the station. If we had still packets on the ring, we wouldn't deallocate the SCD queue and wait for it to be empty. The indication of the queue being empty comes from the Tx response flow which relies on the tid_data structure. The problem is that this structure has been cleared when the station has been removed. In order to solve this issue, block in the STOP_FLUSH ampdu_action until the SCD queue is flushed, and only then, let mac80211 move forward to remove the station. iwlagn_txfifo_flush had to be enhanced to allow this. The bug fixed here caused the "txq_id mismatch: 12 0" print. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Emmanuel Grumbach authored
In commit 33223542 "iwlwifi: mvm: take the valid_{rx,tx}_ant from the TLV" I replaced the access to nvm_data->valid_tx_ant to an inline cheking the TLV flags but forgot a few occurences. Fix that. Change-Id: I92daac735b46738d97fe2dbd5934bb177fd0751b Signed-off-by:
-
Johannes Berg authored
If request_module() failed then we didn't have the correct opmode module that the driver needs to function, so print a warning in this case to make it more obvious what could be wrong. This still won't catch the case where the module simply doesn't exist because it wasn't compiled though. Reviewed-by:
-
Johannes Berg authored
This (slightly) reduces the code size. Signed-off-by: -
Johannes Berg authored
If a new netdev (e.g. an AP VLAN) is created while the driver has queues stopped, the new netdev queues will be started even though they shouldn't. This will lead to frames accumulating on the internal mac80211 pending queues instead of properly being held on the netdev queues. Signed-off-by: -
Johannes Berg authored
Given the (nested) switch statements, this code can't be reached, so make it warn instead of manipulating the carrier state which seems purposeful. Signed-off-by: -
Johannes Berg authored
The netdev queues should always represent the state that the driver gave them, so fiddling with them isn't really appropriate in the mlme code. Also, since we stop queues for flushing now, this really isn't necessary any more. As the scan/offchannel code has also been modified to no longer do this a while ago, remove the outdated smp_mb() and comments about it. While at it, also add a pair of braces that was missing. Signed-off-by: -
Alexander Bondar authored
It's unlikely that an AP requires WMM mandatory admission control for all access categories, and if it does then we still transmit on the background AC without requesting admission. However, avoid using uAPSD in this case since the implementation could run into issues and might use other ACs etc. Signed-off-by:
Alexander Bondar <alexander.bondar@intel.com> Signed-off-by:
-
Johannes Berg authored
When a device is unplugged while suspended, mac80211 is de-initialized and all interfaces are removed while no state is actually present in the driver. This can cause warnings and driver confusion. Fix this by reordering the do_stop code to not call the driver when it is suspended, i.e. when there's no state in the driver anyway. The previous patches removed a few corner cases in ROC and virtual monitor interfaces so that now this is safe to do and no state should be left over. Reported-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
