The 10Mbps link speed was set in 2004 when the ethtool interface was
initially added to the tun driver.  It might have been a good
assumption 18 years ago, but CPUs and network stack came a long way
since then.

Other virtual ports typically report much higher speeds.  For example,
veth reports 10Gbps since its introduction in 2007.

Some userspace applications rely on the current link speed in
certain situations.  For example, Open vSwitch is using link speed
as an upper bound for QoS configuration if user didn't specify the
maximum rate.  Advertised 10Mbps doesn't match reality in a modern
world, so users have to always manually override the value with
something more sensible to avoid configuration issues, e.g. limiting
the traffic too much.  This also creates additional confusion among
users.

Bump the advertised speed to at least match the veth.

Alternative might be to explicitly report UNKNOWN and let the user
decide on a right value for them.  And it is indeed "the right way"
of fixing the problem.  However, that may cause issues with bonding
or with some userspace applications that may rely on speed value to
be reported (even though they should not).  Just changing the speed
value should be a safer option.

Users can still override the speed with ethtool, if necessary.

RFC discussion is linked below.

Link: https://lore.kernel.org/lkml/20221021114921.3705550-1-i.maximets@ovn.org/
Link: https://mail.openvswitch.org/pipermail/ovs-discuss/2022-July/051958.htmlSigned-off-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20221031173953.614577-1-i.maximets@ovn.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Ido Schimmel says:

====================
rocker: Two small changes

Patch #1 avoids allocating and scheduling a work item when it is not
doing any work.

Patch #2 aligns rocker with other switchdev drivers to explicitly mark
FDB entries as offloaded. Needed for upcoming MAB offload [1].

[1] https://lore.kernel.org/netdev/20221025100024.1287157-1-idosch@nvidia.com/
====================

Link: https://lore.kernel.org/r/20221101123936.1900453-1-idosch@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, FDB entries that are notified to the bridge driver via
'SWITCHDEV_FDB_ADD_TO_BRIDGE' are always marked as offloaded by the
bridge. With MAB enabled, this will no longer be universally true.
Device drivers will report locked FDB entries to the bridge to let it
know that the corresponding hosts required authorization, but it does
not mean that these entries are necessarily programmed in the underlying
hardware.

We would like to solve it by having the bridge driver determine the
offload indication based of the 'offloaded' bit in the FDB notification
[1].

Prepare for that change by having rocker explicitly mark learned FDB
entries as offloaded. This is consistent with all the other switchdev
drivers.

[1] https://lore.kernel.org/netdev/20221025100024.1287157-4-idosch@nvidia.com/Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The work item function ofdpa_port_fdb_learn_work() does not do anything
when 'OFDPA_OP_FLAG_LEARNED' is not set in the work item's flags.

Therefore, do not allocate and do not schedule the work item when the
flag is not set.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ef100_enqueue_skb() generates a valid warning with gcc-13:
  drivers/net/ethernet/sfc/ef100_tx.c:370:5: error: conflicting types for 'ef100_enqueue_skb' due to enum/integer mismatch; have 'int(struct efx_tx_queue *, struct sk_buff *)'
  drivers/net/ethernet/sfc/ef100_tx.h:25:13: note: previous declaration of 'ef100_enqueue_skb' with type 'netdev_tx_t(struct efx_tx_queue *, struct sk_buff *)'

I.e. the type of the ef100_enqueue_skb()'s return value in the declaration is
int, while the definition spells enum netdev_tx_t. Synchronize them to the
latter.

Cc: Martin Liska <mliska@suse.cz>
Cc: Edward Cree <ecree.xilinx@gmail.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221031114440.10461-1-jirislaby@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Both bond_alb_xmit() and bond_tlb_xmit() produce a valid warning with
gcc-13:
  drivers/net/bonding/bond_alb.c:1409:13: error: conflicting types for 'bond_tlb_xmit' due to enum/integer mismatch; have 'netdev_tx_t(struct sk_buff *, struct net_device *)' ...
  include/net/bond_alb.h:160:5: note: previous declaration of 'bond_tlb_xmit' with type 'int(struct sk_buff *, struct net_device *)'

  drivers/net/bonding/bond_alb.c:1523:13: error: conflicting types for 'bond_alb_xmit' due to enum/integer mismatch; have 'netdev_tx_t(struct sk_buff *, struct net_device *)' ...
  include/net/bond_alb.h:159:5: note: previous declaration of 'bond_alb_xmit' with type 'int(struct sk_buff *, struct net_device *)'

I.e. the return type of the declaration is int, while the definitions
spell netdev_tx_t. Synchronize both of them to the latter.

Cc: Martin Liska <mliska@suse.cz>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221031114409.10417-1-jirislaby@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

gcc 13 correctly reports overflow in qed_grc_dump_addr_range():
In file included from drivers/net/ethernet/qlogic/qed/qed.h:23,
                 from drivers/net/ethernet/qlogic/qed/qed_debug.c:10:
drivers/net/ethernet/qlogic/qed/qed_debug.c: In function 'qed_grc_dump_addr_range':
include/linux/qed/qed_if.h:1217:9: error: overflow in conversion from 'int' to 'u8' {aka 'unsigned char'} changes value from '(int)vf_id << 8 | 128' to '128' [-Werror=overflow]

We do:
  u8 fid;
  ...
  fid = vf_id << 8 | 128;

Since fid is 16bit (and the stored value above too), fid should be u16,
not u8. Fix that.

Cc: Martin Liska <mliska@suse.cz>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221031114354.10398-1-jirislaby@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This allows BQL to operate avoiding buffer bloat and reducing latency.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20221031104856.32388-1-zajec5@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

1. It is possible to have custom mkex profiles which do not extract
DMAC at all into the key. Hence allow mkex profiles which do not
have DMAC to be loaded into MCAM hardware. This patch also adds
debugging prints needed to identify profiles with wrong
configuration.

2. If a mkex profile set "l2l3mb" field for Rx interface,
then Rx multicast and broadcast entry should be configured.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20221031090856.1404303-1-sumang@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
bpf-next 2022-11-02

We've added 70 non-merge commits during the last 14 day(s) which contain
a total of 96 files changed, 3203 insertions(+), 640 deletions(-).

The main changes are:

1) Make cgroup local storage available to non-cgroup attached BPF programs
   such as tc BPF ones, from Yonghong Song.

2) Avoid unnecessary deadlock detection and failures wrt BPF task storage
   helpers, from Martin KaFai Lau.

3) Add LLVM disassembler as default library for dumping JITed code
   in bpftool, from Quentin Monnet.

4) Various kprobe_multi_link fixes related to kernel modules,
   from Jiri Olsa.

5) Optimize x86-64 JIT with emitting BMI2-based shift instructions,
   from Jie Meng.

6) Improve BPF verifier's memory type compatibility for map key/value
   arguments, from Dave Marchevsky.

7) Only create mmap-able data section maps in libbpf when data is exposed
   via skeletons, from Andrii Nakryiko.

8) Add an autoattach option for bpftool to load all object assets,
   from Wang Yufen.

9) Various memory handling fixes for libbpf and BPF selftests,
   from Xu Kuohai.

10) Initial support for BPF selftest's vmtest.sh on arm64,
    from Manu Bretelle.

11) Improve libbpf's BTF handling to dedup identical structs,
    from Alan Maguire.

12) Add BPF CI and denylist documentation for BPF selftests,
    from Daniel Müller.

13) Check BPF cpumap max_entries before doing allocation work,
    from Florian Lehner.

* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (70 commits)
  samples/bpf: Fix typo in README
  bpf: Remove the obsolte u64_stats_fetch_*_irq() users.
  bpf: check max_entries before allocating memory
  bpf: Fix a typo in comment for DFS algorithm
  bpftool: Fix spelling mistake "disasembler" -> "disassembler"
  selftests/bpf: Fix bpftool synctypes checking failure
  selftests/bpf: Panic on hard/soft lockup
  docs/bpf: Add documentation for new cgroup local storage
  selftests/bpf: Add test cgrp_local_storage to DENYLIST.s390x
  selftests/bpf: Add selftests for new cgroup local storage
  selftests/bpf: Fix test test_libbpf_str/bpf_map_type_str
  bpftool: Support new cgroup local storage
  libbpf: Support new cgroup local storage
  bpf: Implement cgroup storage available to non-cgroup-attached bpf progs
  bpf: Refactor some inode/task/sk storage functions for reuse
  bpf: Make struct cgroup btf id global
  selftests/bpf: Tracing prog can still do lookup under busy lock
  selftests/bpf: Ensure no task storage failure for bpf_lsm.s prog due to deadlock detection
  bpf: Add new bpf_task_storage_delete proto with no deadlock detection
  bpf: bpf_task_storage_delete_recur does lookup first before the deadlock check
  ...
====================

Link: https://lore.kernel.org/r/20221102062120.5724-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Yoshihiro Shimoda says:

====================
net: ethernet: renesas: Add support for "Ethernet Switch"

This patch series is based on next-20221027.

Add initial support for Renesas "Ethernet Switch" device of R-Car S4-8.
The hardware has features about forwarding for an ethernet switch
device. But, for now, it acts as ethernet controllers so that any
forwarding offload features are not supported. So, any switchdev
header files and DSA framework are not used.

Notes that this driver requires some special settings on marvell10g,
Especially host mactype and host speed. And, I need further investigation
to modify the marvell10g driver for upstream. But, the special settings
are applied, this rswitch driver can work correcfly without any changes
of this rswitch driver. So, I believe the rswitch driver can go for
upstream.

Changes from v6:
https://lore.kernel.org/all/20221028065458.2417293-1-yoshihiro.shimoda.uh@renesas.com/
 - Add Reviewed-by tag in the patch [1/3].
 - Fix ordering of initialization because NFS root can start mounting
   the filesystem before register_netdev() even returns

Changes from v5:
https://lore.kernel.org/all/20221027134034.2343230-1-yoshihiro.shimoda.uh@renesas.com/
 - Add maxItems for the ethernet-port/port/reg property.

Changes from v4:
https://lore.kernel.org/all/20221019083518.933070-1-yoshihiro.shimoda.uh@renesas.com/
 - Rebased on next-20221027.
 - Drop some unneeded properties on the dt-bindings doc.
 - Change the subject and commit descriptions on the patch [2/3].
 - Use phylink instead of phylib.
 - Modify struct rswitch_*_desc to remove similar functions ([gs]et_dptr).

====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add R-Car Gen4 gPTP support into the rswitch driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add initial support for Renesas "Ethernet Switch" device of R-Car S4-8.
The hardware has features about forwarding for an ethernet switch
device. But, for now, it acts as ethernet controllers so that any
forwarding offload features are not supported. So, any switchdev
header files and DSA framework are not used.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document Renesas Etherent Switch for R-Car S4-8 (r8a779f0).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mengyuan Lou says:

====================
net: WangXun txgbe/ngbe ethernet driver

This patch series adds support for WangXun NICS, to initialize
interface from software to firmware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Initialize ngbe mac/phy type.
Check whether the firmware is initialized.
Initialize ngbe hw and register netdev.
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add firmware interaction to get EEPROM information.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add mailbox commands to interact with firmware.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the current processing logic, when xdp_redirect occurs, it transmits
the xdp frame based on napi.

If napi of the peer veth is not ready, the veth will drop the packets.
This doesn't meet our expectations.

In this context, we enable napi of the peer veth automatically when the
veth loads the xdp. Then if the veth unloads the xdp, we need to
correctly judge whether to disable napi of the peer veth, because the peer
veth may have loaded xdp, or even the user has enabled GRO.
Signed-off-by: Heng Qi <henqqi@linux.alibaba.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add remote KCOV annotations for NFC processing that is done
in background threads. This enables efficient coverage-guided
fuzzing of the NFC subsystem.

The intention is to add annotations to background threads that
process skb's that were allocated in syscall context
(thus have a KCOV handle associated with the current fuzz test).
This includes nci_recv_frame() that is called by the virtual nci
driver in the syscall context.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Bongsu Jeon <bongsu.jeon@samsung.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, even if just one of the many fragments of a 9k packet
required a copy, we'd copy the whole packet into a freshly-allocated
9k-sized linear SKB, and this led to performance issues.

By having a pool of pages to copy into, each fragment can be
independently handled, leading to a reduced incidence of
allocation and copy.
Signed-off-by: Shailend Chand <shailend@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new iosm wwan port that connects to the modem rpc interface. This
interface provides a configuration channel, and in the case of the 7360, is
the only way to configure the modem (as it does not support mbim).

The new interface is compatible with existing software, such as
open_xdatachannel.py from the xmm7360-pci project [1].

[1] https://github.com/xmm7360/xmm7360-pciSigned-off-by: Shane Parslow <shaneparslow808@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Modem Logging (MDL) port provides an interface to collect modem
logs for debugging purposes. MDL is supported by the relay interface,
and the mtk_t7xx port infrastructure. MDL allows user-space apps to
control logging via mbim command and to collect logs via the relay
interface, while port infrastructure facilitates communication between
the driver and the modem.
Signed-off-by: Moises Veleta <moises.veleta@linux.intel.com>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Acked-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use union inside t7xx_port to group port type specific data members.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commits 36a6503f ("tcp: refine tcp_prune_ofo_queue()
to not drop all packets") and 72cd43ba
("tcp: free batches of packets in tcp_prune_ofo_queue()")
tcp_prune_ofo_queue() drops a fraction of ooo queue,
to make room for incoming packet.

However it makes no sense to drop packets that are
before the incoming packet, in sequence space.

In order to recover from packet losses faster,
it makes more sense to only drop ooo packets
which are after the incoming packet.

Tested:
packetdrill test:
   0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
   +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
   +0 setsockopt(3, SOL_SOCKET, SO_RCVBUF, [3800], 4) = 0
   +0 bind(3, ..., ...) = 0
   +0 listen(3, 1) = 0

   +0 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
   +0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 0>
  +.1 < . 1:1(0) ack 1 win 1024
   +0 accept(3, ..., ...) = 4

 +.01 < . 200:300(100) ack 1 win 1024
   +0 > . 1:1(0) ack 1 <nop,nop, sack 200:300>

 +.01 < . 400:500(100) ack 1 win 1024
   +0 > . 1:1(0) ack 1 <nop,nop, sack 400:500 200:300>

 +.01 < . 600:700(100) ack 1 win 1024
   +0 > . 1:1(0) ack 1 <nop,nop, sack 600:700 400:500 200:300>

 +.01 < . 800:900(100) ack 1 win 1024
   +0 > . 1:1(0) ack 1 <nop,nop, sack 800:900 600:700 400:500 200:300>

 +.01 < . 1000:1100(100) ack 1 win 1024
   +0 > . 1:1(0) ack 1 <nop,nop, sack 1000:1100 800:900 600:700 400:500>

 +.01 < . 1200:1300(100) ack 1 win 1024
   +0 > . 1:1(0) ack 1 <nop,nop, sack 1200:1300 1000:1100 800:900 600:700>

// this packet is dropped because we have no room left.
 +.01 < . 1400:1500(100) ack 1 win 1024

 +.01 < . 1:200(199) ack 1 win 1024
// Make sure kernel did not drop 200:300 sequence
   +0 > . 1:1(0) ack 300 <nop,nop, sack 1200:1300 1000:1100 800:900 600:700>
// Make room, since our RCVBUF is very small
   +0 read(4, ..., 299) = 299

 +.01 < . 300:400(100) ack 1 win 1024
   +0 > . 1:1(0) ack 500 <nop,nop, sack 1200:1300 1000:1100 800:900 600:700>

 +.01 < . 500:600(100) ack 1 win 1024
   +0 > . 1:1(0) ack 700 <nop,nop, sack 1200:1300 1000:1100 800:900>

   +0 read(4, ..., 400) = 400

 +.01 < . 700:800(100) ack 1 win 1024
   +0 > . 1:1(0) ack 900 <nop,nop, sack 1200:1300 1000:1100>

 +.01 < . 900:1000(100) ack 1 win 1024
   +0 > . 1:1(0) ack 1100 <nop,nop, sack 1200:1300>

 +.01 < . 1100:1200(100) ack 1 win 1024
// This checks that 1200:1300 has not been removed from ooo queue
   +0 > . 1:1(0) ack 1300
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20221101035234.3910189-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

inet[46]_pton check the input length against
a sane length limit (INET[6]_ADDRSTRLEN), but
the strlen value gets truncated due to being stored in an int,
so there's a theoretical potential for a >4G string to pass
the limit test.
Use size_t since that's what strlen actually returns.

I've had a hunt for callers that could hit this, but
I've not managed to find anything that doesn't get checked with
some other limit first; but it's possible that I've missed
something in the depth of the storage target paths.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20221029014604.114024-1-linux@treblig.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix 'cofiguration' typo in BPF samples README.
Signed-off-by: Kang Minchul <tegongkang@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20221030180254.34138-1-tegongkang@gmail.com

Eric Dumazet says:

====================
inet: add drop monitor support

I recently tried to analyse flakes in ip_defrag selftest.
This failed miserably.

IPv4 and IPv6 reassembly units are causing false kfree_skb()
notifications. It is time to deal with this issue.

First two patches are changing core networking to better
deal with eventual skb frag_list chains, in respect
of kfree_skb/consume_skb status.

Last three patches are adding three new drop reasons,
and make sure skbs that have been reassembled into
a large datagram are no longer viewed as dropped ones.

After this, understanding why ip_defrag selftest is flaky
is possible using standard drop monitoring tools.
====================

Link: https://lore.kernel.org/r/20221029154520.2747444-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

IPv4 reassembly unit can decide to drop frags based on
/proc/sys/net/ipv4/ipfrag_max_dist sysctl.

Add a specific drop reason to track this specific
and weird case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Used to track skbs freed after a timeout happened
in a reassmbly unit.

Passing a @reason argument to inet_frag_rbtree_purge()
allows to use correct consumed status for frags
that have been successfully re-assembled.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This is used to track when a duplicate segment received by various
reassembly units is dropped.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When an skb with a frag list is consumed, we currently
pretend all skbs in the frag list were dropped.

In order to fix this, add a @reason argument to skb_release_data()
and skb_release_all().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This will allow to simply use in the future:

	kfree_skb_reason(skb, reason);

Instead of repeating sequences like:

	if (dropped)
	    kfree_skb_reason(skb, reason);
	else
	    consume_skb(skb);

For instance, following patch in the series is adding
@reason to skb_release_data() and skb_release_all(),
so that we can propagate a meaningful @reason whenever
consume_skb()/kfree_skb() have to take care of a potential frag_list.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

RDMA overflows can happen if the Ethernet controller does not have
enough bandwidth allocated at the memory controller level, report RDMA
overflows and deal with saturation, similar to the RBUF overflow
counter.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221028222141.3208429-1-f.fainelli@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If the FTMAC100 is used as a DSA master, then it is expected that frames
which are MTU sized on the wire facing the external switch port (1500
octets in L2 payload, plus L2 header) also get a DSA tag when seen by
the host port.

This extra tag increases the length of the packet as the host port sees
it, and the FTMAC100 is not prepared to handle frames whose length
exceeds 1518 octets (including FCS) at all.

Only a minimal rework is needed to support this configuration. Since
MTU-sized DSA-tagged frames still fit within a single buffer (RX_BUF_SIZE),
we just need to optimize the resource management rather than implement
multi buffer RX.

In ndo_change_mtu(), we toggle the FTMAC100_MACCR_RX_FTL bit to tell the
hardware to drop (or not) frames with an L2 payload length larger than
1500. We need to replicate the MACCR configuration in ftmac100_start_hw()
as well, since there is a hardware reset there which clears previous
settings.

The advantage of dynamically changing FTMAC100_MACCR_RX_FTL is that when
dev->mtu is at the default value of 1500, large frames are automatically
dropped in hardware and we do not spend CPU cycles dropping them.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Link: https://lore.kernel.org/r/20221028183220.155948-3-saproj@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The driver uses the MAX_PKT_SIZE (1518) for both MTU reporting and for
TX. However, the 2 places do not measure the same thing.

On TX, skb->len measures the entire L2 packet length (without FCS, which
software does not possess). So the comparison against 1518 there is
correct.

What is not correct is the reporting of dev->max_mtu as 1518. Since MTU
measures L2 *payload* length (excluding L2 overhead) and not total L2
packet length, it means that the correct max_mtu supported by this
device is the standard 1500. Anything higher than that will be dropped
on RX currently.

To fix this, subtract VLAN_ETH_HLEN from MAX_PKT_SIZE when reporting the
max_mtu, since that is the difference between L2 payload length and
total L2 length as seen by software.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Link: https://lore.kernel.org/r/20221028183220.155948-2-saproj@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Eliminate one check in the data path and move it elsewhere, to where our
real limitation is. We'll want to start processing "too long" frames in
the driver (currently there is a hardware MAC setting which drops
theses).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Link: https://lore.kernel.org/r/20221028183220.155948-1-saproj@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, the .port_set_rgmii_delay hook is missing for the 88E6320
family, which causes failure to retrieve an IP address via DHCP.

Add mv88e6320_port_set_rgmii_delay() that allows applying the RGMII
delay for ports 2, 5, and 6, which are the only ports that can be used
in RGMII mode.

Tested on a custom i.MX8MN board connected to an 88E6320 switch.

This change also applies safely to the 88E6321 variant.

The only difference between 88E6320 versus 88E6321 is the temperature
grade and pinout.

They share exactly the same MDIO register map for ports 2, 5, and 6,
which are the only ports that can be used in RGMII mode.
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
[fabio: Improved commit log and extended it to mv88e6321_ops]
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221028163158.198108-1-festevam@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Hangbin Liu says:

====================
rtnetlink: Honour NLM_F_ECHO flag in rtnl_{new, del}link

Netlink messages are used for communicating between user and kernel space.
When user space configures the kernel with netlink messages, it can set the
NLM_F_ECHO flag to request the kernel to send the applied configuration back
to the caller. This allows user space to retrieve configuration information
that are filled by the kernel (either because these parameters can only be
set by the kernel or because user space let the kernel choose a default
value).

The kernel has support this feature in some places like RTM_{NEW, DEL}ADDR,
RTM_{NEW, DEL}ROUTE. This patch set handles NLM_F_ECHO flag and send link
info back after rtnl_{new, del}link.
====================

Link: https://lore.kernel.org/r/20221028084224.3509611-1-liuhangbin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This patch use the new helper unregister_netdevice_many_notify() for
rtnl_delete_link(), so that the kernel could reply unicast when userspace
 set NLM_F_ECHO flag to request the new created interface info.

At the same time, the parameters of rtnl_delete_link() need to be updated
since we need nlmsghdr and portid info.
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>