- 17 Feb, 2020 16 commits
-
-
Dmitry Bogdanov authored
fix static checker warning: drivers/net/ethernet/aquantia/atlantic/aq_filters.c:166 aq_check_approve_fvlan() error: passing untrusted data to 'test_bit()' Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 7975d2af: ("net: aquantia: add support of rx-vlan-filter offload") Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pavel Belous authored
during hibernation freeze, aq_nic_stop could be invoked on a stopped device. That may cause panic on access to not yet allocated vector/ring structures. Add a check to stop device if it is not yet stopped. Similiarly after freeze in hibernation thaw, aq_nic_start could be invoked on a not initialized net device. Result will be the same. Add a check to start device if it is initialized. In our case, this is the same as started. Fixes: 8aaa112a ("net: atlantic: refactoring pm logic") Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Nikita Danilov <ndanilov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pavel Belous authored
Code inspection found that in case of mapping error we do return current 'ret' value. But beside error, it is used to count number of descriptors allocated for the packet. In that case map_skb function could return '1'. Changing it to return zero (number of mapped descriptors for skb) Fixes: 018423e9 ("net: ethernet: aquantia: Add ring support code") Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pavel Belous authored
skb->len is used to calculate statistics after xmit invocation. Under a stress load it may happen that skb will be xmited, rx interrupt will come and skb will be freed, all before xmit function is even returned. Eventually, skb->len will access unallocated area. Moving stats calculation into tx_clean routine. Fixes: 018423e9 ("net: ethernet: aquantia: Add ring support code") Reported-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nikita Danilov authored
Add checks to not enable multiple loopback modes simultaneously, It was also discovered that for dma loopback to function correctly promisc mode should be enabled on device. Fixes: ea4b4d7f ("net: atlantic: loopback tests via private flags") Signed-off-by: Nikita Danilov <ndanilov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Egor Pomozov authored
Clock adjustment data should be passed to FW as well, otherwise in some cases a drift was observed when using GPIO features. Signed-off-by: Egor Pomozov <epomozov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Igor Russkikh authored
Artificial HW reliability tests revealed a possible hangup in the driver. Normally, when device disappears from bus, all register reads returns 0xFFFFFFFF. At remote procedure invocation towards FW there is a logic where result is compared with -1 in a loop. That caused an infinite loop if hardware due to some issues disappears from bus. Add extra result checks to prevent this. Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dmitry Bezrukov authored
Yet another checksum offload compatibility issue was found. The known issue is that AQC HW marks tcp packets with 0xFFFF checksum as invalid (1). This is workarounded in driver, passing all the suspicious packets up to the stack for further csum validation. Another HW problem (2) is that it hides invalid csum of LRO aggregated packets inside of the individual descriptors. That was workarounded by forced scan of all LRO descriptors for checksum errors. However the scan logic was joint for both LRO and multi-descriptor packets (jumbos). And this causes the issue. We have to drop LRO packets with the detected bad checksum because of (2), but we have to pass jumbo packets to stack because of (1). When using windows tcp partner with jumbo frames but with LSO disabled driver discards such frames as bad checksummed. But only LRO frames should be dropped, not jumbos. On such a configurations tcp stream have a chance of drops and stucks. (1) 76f254d4 ("net: aquantia: tcp checksum 0xffff being handled incorrectly") (2) d08b9a0a ("net: aquantia: do not pass lro session with invalid tcp checksum") Fixes: d08b9a0a ("net: aquantia: do not pass lro session with invalid tcp checksum") Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hangbin Liu authored
After commit 71130f29 ("vxlan: fix tos value before xmit") we start strict vxlan xmit tos value by RT_TOS(), which limits the tos value less than 0x1E. With current value 0x40 the test will failed with "v1: Expected to capture 10 packets, got 0". So let's choose a smaller tos value for testing. Fixes: d417ecf5 ("selftests: forwarding: vxlan_bridge_1d: Add a TOS test") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Since IFLA_ALT_IFNAME is an NLA_STRING, we have no guarantee it is nul terminated. We should use nla_strdup() instead of kstrdup(), since this helper will make sure not accessing out-of-bounds data. BUG: KMSAN: uninit-value in strlen+0x5e/0xa0 lib/string.c:535 CPU: 1 PID: 19157 Comm: syz-executor.5 Not tainted 5.5.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x220 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 strlen+0x5e/0xa0 lib/string.c:535 kstrdup+0x7f/0x1a0 mm/util.c:59 rtnl_alt_ifname net/core/rtnetlink.c:3495 [inline] rtnl_linkprop+0x85d/0xc00 net/core/rtnetlink.c:3553 rtnl_newlinkprop+0x9d/0xb0 net/core/rtnetlink.c:3568 rtnetlink_rcv_msg+0x1153/0x1570 net/core/rtnetlink.c:5424 netlink_rcv_skb+0x451/0x650 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5442 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0xf9e/0x1100 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x1248/0x14d0 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x45b3b9 Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ff1c7b1ac78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007ff1c7b1b6d4 RCX: 000000000045b3b9 RDX: 0000000000000000 RSI: 0000000020000040 RDI: 0000000000000003 RBP: 000000000075bf20 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff R13: 00000000000009cb R14: 00000000004cb3dd R15: 000000000075bf2c Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline] kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82 slab_alloc_node mm/slub.c:2774 [inline] __kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4382 __kmalloc_reserve net/core/skbuff.c:141 [inline] __alloc_skb+0x2fd/0xac0 net/core/skbuff.c:209 alloc_skb include/linux/skbuff.h:1049 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1174 [inline] netlink_sendmsg+0x7d3/0x14d0 net/netlink/af_netlink.c:1892 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 36fbf1e5 ("net: rtnetlink: add linkprop commands to add and delete alternative ifnames") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jiri Pirko <jiri@mellanox.com> Reported-by: syzbot <syzkaller@googlegroups.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexandre Belloni authored
Because of autosuspend, at91ether_start is called with clocks disabled. Ensure that pm_runtime doesn't suspend the interface as soon as it is opened as there is no pm_runtime support is the other relevant parts of the platform support for at91rm9200. Fixes: d54f89af ("net: macb: Add pm runtime support") Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jethro Beekman authored
In 709772e6, RT_TABLE_COMPAT was added to allow legacy software to deal with routing table numbers >= 256, but the same change to FIB rule queries was overlooked. Signed-off-by: Jethro Beekman <jethro@fortanix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Leon Romanovsky authored
Convert net/rds to use the newly introduces pin_user_pages() API, which properly sets FOLL_PIN. Setting FOLL_PIN is now required for code that requires tracking of pinned pages. Note that this effectively changes the code's behavior: it now ultimately calls set_page_dirty_lock(), instead of set_page_dirty(). This is probably more accurate. As Christoph Hellwig put it, "set_page_dirty() is only safe if we are dealing with a file backed page where we have reference on the inode it hangs off." [1] [1] https://lore.kernel.org/r/20190723153640.GB720@lst.de Cc: Hans Westgaard Ry <hans.westgaard.ry@oracle.com> Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: John Hubbard <jhubbard@nvidia.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Benjamin Poirier authored
When splitting an RTA_MULTIPATH request into multiple routes and adding the second and later components, we must not simply remove NLM_F_REPLACE but instead replace it by NLM_F_CREATE. Otherwise, it may look like the netlink message was malformed. For example, ip route add 2001:db8::1/128 dev dummy0 ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0 \ nexthop via fe80::30:2 dev dummy0 results in the following warnings: [ 1035.057019] IPv6: RTM_NEWROUTE with no NLM_F_CREATE or NLM_F_REPLACE [ 1035.057517] IPv6: NLM_F_CREATE should be set when creating new route This patch makes the nlmsg sequence look equivalent for __ip6_ins_rt() to what it would get if the multipath route had been added in multiple netlink operations: ip route add 2001:db8::1/128 dev dummy0 ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0 ip route append 2001:db8::1/128 nexthop via fe80::30:2 dev dummy0 Fixes: 27596472 ("ipv6: fix ECMP route replacement") Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Benjamin Poirier authored
After commit 27596472 ("ipv6: fix ECMP route replacement") it is no longer possible to replace an ECMP-able route by a non ECMP-able route. For example, ip route add 2001:db8::1/128 via fe80::1 dev dummy0 ip route replace 2001:db8::1/128 dev dummy0 does not work as expected. Tweak the replacement logic so that point 3 in the log of the above commit becomes: 3. If the new route is not ECMP-able, and no matching non-ECMP-able route exists, replace matching ECMP-able route (if any) or add the new route. We can now summarize the entire replace semantics to: When doing a replace, prefer replacing a matching route of the same "ECMP-able-ness" as the replace argument. If there is no such candidate, fallback to the first route found. Fixes: 27596472 ("ipv6: fix ECMP route replacement") Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hangbin Liu authored
For tc ip_proto filter, when we extract the flow via __skb_flow_dissect() without flag FLOW_DISSECTOR_F_STOP_AT_ENCAP, we will continue extract to the inner proto. So for GRE + ICMP messages, we should not track GRE proto, but inner ICMP proto. For test mirror_gre.sh, it may make user confused if we capture ICMP message on $h3(since the flow is GRE message). So I move the capture dev to h3-gt{4,6}, and only capture ICMP message. Before the fix: ]# ./mirror_gre.sh TEST: ingress mirror to gretap (skip_hw) [ OK ] TEST: egress mirror to gretap (skip_hw) [ OK ] TEST: ingress mirror to ip6gretap (skip_hw) [ OK ] TEST: egress mirror to ip6gretap (skip_hw) [ OK ] TEST: ingress mirror to gretap: envelope MAC (skip_hw) [FAIL] Expected to capture 10 packets, got 0. TEST: egress mirror to gretap: envelope MAC (skip_hw) [FAIL] Expected to capture 10 packets, got 0. TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw) [FAIL] Expected to capture 10 packets, got 0. TEST: egress mirror to ip6gretap: envelope MAC (skip_hw) [FAIL] Expected to capture 10 packets, got 0. TEST: two simultaneously configured mirrors (skip_hw) [ OK ] WARN: Could not test offloaded functionality After fix: ]# ./mirror_gre.sh TEST: ingress mirror to gretap (skip_hw) [ OK ] TEST: egress mirror to gretap (skip_hw) [ OK ] TEST: ingress mirror to ip6gretap (skip_hw) [ OK ] TEST: egress mirror to ip6gretap (skip_hw) [ OK ] TEST: ingress mirror to gretap: envelope MAC (skip_hw) [ OK ] TEST: egress mirror to gretap: envelope MAC (skip_hw) [ OK ] TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw) [ OK ] TEST: egress mirror to ip6gretap: envelope MAC (skip_hw) [ OK ] TEST: two simultaneously configured mirrors (skip_hw) [ OK ] WARN: Could not test offloaded functionality Fixes: ba8d3987 ("selftests: forwarding: Add test for mirror to gretap") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Petr Machata <pmachata@gmail.com> Tested-by: Petr Machata <pmachata@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 14 Feb, 2020 24 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix interrupt name truncation in mv88e6xxx dsa driver, from Andrew Lunn. 2) Process generic XDP even if SKB is cloned, from Toke Høiland-Jørgensen. 3) Fix leak of kernel memory to userspace in smc, from Eric Dumazet. 4) Add some missing netlink attribute validation to matchall and flower, from Davide Caratti. 5) Send icmp responses properly when NAT has been applied to the frame before we get to the tunnel emitting the icmp, from Jason Donenfeld. 6) Make sure there is enough SKB headroom when adding dsa tags for qca and ar9331. From Per Forlin. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits) netdevice.h: fix all kernel-doc and Sphinx warnings net: dsa: tag_ar9331: Make sure there is headroom for tag net: dsa: tag_qca: Make sure there is headroom for tag net, ip6_tunnel: enhance tunnel locate with link check net/smc: no peer ID in CLC decline for SMCD net/smc: transfer fasync_list in case of fallback net: hns3: fix a copying IPv6 address error in hclge_fd_get_flow_tuples() net: hns3: fix VF bandwidth does not take effect in some case net: hns3: add management table after IMP reset mac80211: fix wrong 160/80+80 MHz setting cfg80211: add missing policy for NL80211_ATTR_STATUS_CODE xfrm: interface: use icmp_ndo_send helper wireguard: device: use icmp_ndo_send helper sunvnet: use icmp_ndo_send helper gtp: use icmp_ndo_send helper icmp: introduce helper for nat'd source address in network device context net/sched: flower: add missing validation of TCA_FLOWER_FLAGS net/sched: matchall: add missing validation of TCA_MATCHALL_FLAGS net/flow_dissector: remove unexist field description page_pool: refill page when alloc.count of pool is zero ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull power management fixes from Rafael Wysocki: "Fix three issues related to the handling of wakeup events signaled through the ACPI SCI while suspended to idle (Rafael Wysocki) and unexport an internal cpufreq variable (Yangtao Li)" * tag 'pm-5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system ACPICA: Introduce acpi_any_gpe_status_set() ACPI: PM: s2idle: Avoid possible race related to the EC GPE ACPI: EC: Fix flushing of pending work cpufreq: Make cpufreq_global_kobject static
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/soundLinus Torvalds authored
Pull sound fixes from Takashi Iwai: "The only common change is the regression fix of the previous PCM fix patch for managed buffers while the rest are usual suspects, USB-audio and HD-audio device-specific quirks. The change for UAC2 clock validation workaround became a bit big, but the changes are fairly straightforward" * tag 'sound-5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: pcm: Fix double hw_free calls ALSA: usb-audio: Add clock validity quirk for Denon MC7000/MCX8000 ALSA: hda/realtek - Fix silent output on MSI-GL73 ALSA: hda/realtek - Add more codec supported Headset Button ALSA: usb-audio: Apply sample rate quirk for Audioengine D1 ALSA: usb-audio: Fix UAC2/3 effect unit parsing ALSA: usb-audio: Apply 48kHz fixed rate playback for Jabra Evolve 65 headset
-
git://anongit.freedesktop.org/drm/drmLinus Torvalds authored
Pull drm fixes from Dave Airlie: "The core has a build fix for edid code on certain compilers/arches/, one MST fix and one vgem fix. Regular amdgpu fixes, and a couple of small driver fixes. The i915 fixes are bit larger than normal for this stage, but they were having CI issues last week, and they hadn't sent any fixes last week due to this. core: - edid build fix mst: - fix NULL ptr deref vgem: - fix close after free msm: - better dma-api usage sun4i: - disable allow_fb_modifiers amdgpu: - Additional OD fixes for navi - Misc display fixes - VCN 2.5 DPG fix - Prevent build errors on PowerPC on some configs - GDS EDC fix i915: - dsi/acpi fixes - gvt locking and allocation fixes - gem/gt fixes - bios timing parameters fix" * tag 'drm-fixes-2020-02-14' of git://anongit.freedesktop.org/drm/drm: (50 commits) drm/i915: Mark the removal of the i915_request from the sched.link drm/i915/execlists: Reclaim the hanging virtual request drm/i915/execlists: Take a reference while capturing the guilty request drm/i915/execlists: Offline error capture drm/i915/gt: Allow temporary suspension of inflight requests drm/i915: Keep track of request among the scheduling lists drm/i915/gem: Tighten checks and acquiring the mmap object drm/i915: Fix preallocated barrier list append drm/i915/gt: Acquire ce->active before ce->pin_count/ce->pin_mutex drm/i915: Tighten atomicity of i915_active_acquire vs i915_active_release drm/i915: Stub out i915_gpu_coredump_put drm/amdgpu:/navi10: use the ODCAP enum to index the caps array drm/amdgpu: update smu_v11_0_pptable.h drm/amdgpu: correct comment to clear up the confusion drm/amd/display: DCN2.x Do not program DPPCLK if same value drm/amd/display: Don't map ATOM_ENABLE to ATOM_INIT drm/amdgpu/vcn2.5: fix warning drm/amdgpu: limit GDS clearing workaround in cold boot sequence drm/amdgpu: fix amdgpu pmu to use hwc->config instead of hwc->conf amdgpu: Prevent build errors regarding soft/hard-float FP ABI tags ...
-
Randy Dunlap authored
Eliminate all kernel-doc and Sphinx warnings in <linux/netdevice.h>. Fixes these warnings: ../include/linux/netdevice.h:2100: warning: Function parameter or member 'gso_partial_features' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'l3mdev_ops' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'xfrmdev_ops' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'tlsdev_ops' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'name_assign_type' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'ieee802154_ptr' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'mpls_ptr' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'xdp_prog' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'gro_flush_timeout' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'xdp_bulkq' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'xps_cpus_map' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'xps_rxqs_map' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'qdisc_hash' not described in 'net_device' ../include/linux/netdevice.h:3552: WARNING: Inline emphasis start-string without end-string. ../include/linux/netdevice.h:3552: WARNING: Inline emphasis start-string without end-string. Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Per Forlin says: ==================== net: dsa: Make sure there is headroom for tag Sorry for re-posting yet another time.... I manage to include multiple email-senders and forgot to include cover-letter. Let's hope everyhthing is in order this time. Fix two tag drivers to make sure there is headroom for the tag data. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Per Forlin authored
Passing tag size to skb_cow_head will make sure there is enough headroom for the tag data. This change does not introduce any overhead in case there is already available headroom for tag. Signed-off-by: Per Forlin <perfn@axis.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Per Forlin authored
Passing tag size to skb_cow_head will make sure there is enough headroom for the tag data. This change does not introduce any overhead in case there is already available headroom for tag. Signed-off-by: Per Forlin <perfn@axis.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
William Dauchy authored
With ipip, it is possible to create an extra interface explicitly attached to a given physical interface: # ip link show tunl0 4: tunl0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ipip 0.0.0.0 brd 0.0.0.0 # ip link add tunl1 type ipip dev eth0 # ip link show tunl1 6: tunl1@eth0: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ipip 0.0.0.0 brd 0.0.0.0 But it is not possible with ip6tnl: # ip link show ip6tnl0 5: ip6tnl0@NONE: <NOARP> mtu 1452 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/tunnel6 :: brd :: # ip link add ip6tnl1 type ip6tnl dev eth0 RTNETLINK answers: File exists This patch aims to make it possible by adding link comparaison in both tunnel locate and lookup functions; we also modify mtu calculation when attached to an interface with a lower mtu. This permits to make use of x-netns communication by moving the newly created tunnel in a given netns. Signed-off-by: William Dauchy <w.dauchy@criteo.com> Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'mac80211-for-net-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Just a few fixes: * avoid running out of tracking space for frames that need to be reported to userspace by using more bits * fix beacon handling suppression by adding some relevant elements to the CRC calculation * fix quiet mode in action frames * fix crash in ethtool for virt_wifi and similar * add a missing policy entry * fix 160 & 80+80 bandwidth to take local capabilities into account ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Karsten Graul says: ==================== net/smc: fixes for -net Fix a syzbot finding and a problem with the CLC handshake content. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ursula Braun authored
Just SMCR requires a CLC Peer ID, but not SMCD. The field should be zero for SMCD. Fixes: c758dfdd ("net/smc: add SMC-D support in CLC messages") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ursula Braun authored
SMC does not work together with FASTOPEN. If sendmsg() is called with flag MSG_FASTOPEN in SMC_INIT state, the SMC-socket switches to fallback mode. To handle the previous ioctl FIOASYNC call correctly in this case, it is necessary to transfer the socket wait queue fasync_list to the internal TCP socket. Reported-by: syzbot+4b1fe8105f8044a26162@syzkaller.appspotmail.com Fixes: ee9dfbef ("net/smc: handle sockopts forcing fallback") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Huazhong Tan says: ==================== net: hns3: fixes for -net This series includes three bugfixes for the HNS3 ethernet driver. [patch 1] fixes a management table lost issue after IMP reset. [patch 2] fixes a VF bandwidth configuration not work problem. [patch 3] fixes a problem related to IPv6 address copying. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Guangbin Huang authored
The IPv6 address defined in struct in6_addr is specified as big endian, but there is no specified endian in struct hclge_fd_rule_tuples, so it will cause a problem if directly use memcpy() to copy ipv6 address between these two structures since this field in struct hclge_fd_rule_tuples is little endian. This patch fixes this problem by using be32_to_cpu() to convert endian of IPv6 address of struct in6_addr before copying. Fixes: d93ed94f ("net: hns3: add aRFS support for PF") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yonglong Liu authored
When enabling 4 TC after setting the bandwidth of VF, the bandwidth of VF will resume to default value, because of the qset resources changed in this case. This patch fixes it by using a fixed VF's qset resources according to HNAE3_MAX_TC macro. Fixes: ee9e4424 ("net: hns3: add support for configuring bandwidth of VF on the host") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yufeng Mo authored
In the current process, the management table is missing after the IMP reset. This patch adds the management table to the reset process. Fixes: f5aac71c ("net: hns3: add manager table initialization for hardware") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rafael J. Wysocki authored
* pm-cpufreq: cpufreq: Make cpufreq_global_kobject static
-
Shay Bar authored
Before this patch, STA's would set new width of 160/80+80 MHz based on AP capability only. This is wrong because STA may not support > 80MHz BW. Fix is to verify STA has 160/80+80 MHz capability before increasing its width to > 80MHz. The "support_80_80" and "support_160" setting is based on: "Table 9-272 — Setting of the Supported Channel Width Set subfield and Extended NSS BW Support subfield at a STA transmitting the VHT Capabilities Information field" From "Draft P802.11REVmd_D3.0.pdf" Signed-off-by: Aviad Brikman <aviad.brikman@celeno.com> Signed-off-by: Shay Bar <shay.bar@celeno.com> Link: https://lore.kernel.org/r/20200210130728.23674-1-shay.bar@celeno.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>
-
Sergey Matyukevich authored
The nl80211_policy is missing for NL80211_ATTR_STATUS_CODE attribute. As a result, for strictly validated commands, it's assumed to not be supported. Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Link: https://lore.kernel.org/r/20200213131608.10541-2-sergey.matyukevich.os@quantenna.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>
-
Dave Airlie authored
Merge tag 'drm-intel-next-fixes-2020-02-13' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes drm/i915 fixes for v5.6-rc2 Most of these were aimed at a "next fixes" pull already during the merge window, but there were issues with the baseline I used, which resulted in a lot of issues in CI. I've regenerated this stuff piecemeal now, adding gradually to it, and it seems healthy now. Due to the issues this is much bigger than I'd like. But it was obviously necessary to take the time to ensure it's not garbage... Signed-off-by: Dave Airlie <airlied@redhat.com> From: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/878sl6yfrn.fsf@intel.com
-
Dave Airlie authored
Merge tag 'amd-drm-fixes-5.6-2020-02-12' of git://people.freedesktop.org/~agd5f/linux into drm-fixes amd-drm-fixes-5.6-2020-02-12: amdgpu: - Additional OD fixes for navi - Misc display fixes - VCN 2.5 DPG fix - Prevent build errors on PowerPC on some configs - GDS EDC fix Signed-off-by: Dave Airlie <airlied@redhat.com> From: Alex Deucher <alexdeucher@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200212224746.3992-1-alexander.deucher@amd.com
-
Dave Airlie authored
Merge tag 'drm-misc-next-fixes-2020-02-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes drm-misc-next fixes for v5.6: - Fix build error in drm/edid. - Plug close-after-free race in vgem_gem_create. - Handle CONFIG_DMA_API_DEBUG_SG better in drm/msm. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/551b6183-a581-9d12-10a9-24cd929de425@linux.intel.com
-
git://anongit.freedesktop.org/drm/drm-miscDave Airlie authored
Fixes for v5.6: - Revert allow_fb_modifiers in sun4i, as it causes a regression for DE2 and DE3. - Fix null pointer deref in drm_dp_mst_process_up_req(). Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/672810c3-4212-0a46-337b-2cb855573fd2@linux.intel.com
-