Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add support to STM LSM6DSRX 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6dsrx.pdfSigned-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

None of the ST sensor drivers use any symbols from
<linux/gpio.h>, just drop the include from all of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Set gain in hx711_reset() to its default value after a reset cycle. This
omits one precautionary read cycle, because the read is performed in
hx711_set_gain_for_channel() anyway if gain has changed.

Check for DOUT low and if its high wait some time if it goes down
instead of doing a blind reset cycle when DOUT is not down.

This is a performance optimization which allows to query the sensor with
a higher frequency.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Fix the following warnings when documentation is built:
drivers/iio/adc/stm32-adc-core.c:62: warning: cannot understand function
 prototype: 'struct stm32_adc_common_regs '
drivers/iio/adc/stm32-adc-core.c:78: warning: cannot understand function
 prototype: 'struct stm32_adc_priv_cfg '
drivers/iio/adc/stm32-adc-core.c:123: warning: Function parameter or
 member 'pdev' not described in 'stm32f4_adc_clk_sel'
drivers/iio/adc/stm32-adc.c:219: warning: cannot understand function
 prototype: 'struct stm32_adc_regs '
drivers/iio/adc/stm32-adc.c:237: warning: cannot understand function
 prototype: 'struct stm32_adc_regspec '
drivers/iio/adc/stm32-adc.c:264: warning: cannot understand function
 prototype: 'struct stm32_adc_cfg '
drivers/iio/adc/stm32-adc.c:323: warning: Function parameter or member
 'difsel' not described in 'N'
drivers/iio/adc/stm32-adc.c:323: warning: Function parameter or member
 'pcsel' not described in 'stm32_adc'
drivers/iio/adc/stm32-adc.c:371: warning: cannot understand function
 prototype: 'const struct stm32_adc_regs stm32f4_sq[STM32_ADC_MAX_SQ + 1]
drivers/iio/adc/stm32-adc.c:417: warning: cannot understand function
 prototype: 'const struct stm32_adc_regs stm32f4_smp_bits[] = '
drivers/iio/adc/stm32-adc.c:508: warning: cannot understand function
 prototype: 'const struct stm32_adc_regs stm32h7_smp_bits[] = '
drivers/iio/adc/stm32-adc.c:1112: warning: Function parameter or member
 'indio_dev' not described in 'stm32_adc_get_trig_extsel'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
 'indio_dev' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
 'reg' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
 'writeval' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
 'readval' not described in 'stm32_adc_debugfs_reg_access'
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.

The iio_triggered_buffer_postenable() should be called before (to attach
the poll func) and then the

The iio_triggered_buffer_predisable() function is hooked directly without
anything, which is probably fine, as the postenable() version seems to also
do some reset/wake-up of the device.
This will mean it will be easier when removing it; i.e. it just gets
removed.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Suggested by coccinelle / coccicheck.

CHECK   drivers/iio/chemical/sgp30.c
drivers/iio/chemical/sgp30.c:486:2-3: Unneeded semicolon
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Andreas Brauchli <a.brauchli@elementarea.net>

Suggestion from coccinelle / coccicheck

CHECK   drivers/iio/adc/twl4030-madc.c
drivers/iio/adc/twl4030-madc.c:524:6-15: WARNING: Comparison of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:655:1-43: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:659:2-44: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:664:1-43: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:498:2-34: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:510:2-19: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:511:2-11: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:531:2-19: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:532:2-11: WARNING: Assignment of 0/1 to bool variable
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>

Document the LTC2983 temperature sensor devicetree bindings.

Tweaked by Jonathan to take into account the lack of signed output
being maintained by dtc yaml output.  For now a comment added
that the unsigned array should actually be signed.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The LTC2983 is a Multi-Sensor High Accuracy Digital Temperature
Measurement System. It measures a wide variety of temperature sensors and
digitally outputs the result, in °C or °F, with 0.1°C accuracy and
0.001°C resolution. It can measure the temperature of all standard
thermocouples (type B,E,J,K,N,S,R,T), standard 2-,3-,4-wire RTDs,
thermistors and diodes.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

We can drop some duplicate code if we use devm_action for disabling
regulators and pm and the managed variant of iio_device_register().

This allows us to completely remove all remove() callbacks from both
i2c and spi code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The vddd and vdda supplies are always operated on together. We can
shrink the code a bit by using the bulk regulator helpers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

FXOS8700CQ is a small, low-power, 3-axis linear accelerometer and 3-axis
magnetometer combined into a single package. The device features a
selectable I2C or point-to-point SPI serial interface with 14-bit
accelerometer and 16-bit magnetometer ADC resolution along with
smart-embedded functions.

FXOS8700CQ has dynamically selectable accelerationfull-scale ranges of
±2 g/±4 g/±8 g and a fixed magnetic measurement range of ±1200 μT.
Output data rates (ODR) from 1.563 Hz to 800 Hz are selectable by the user
for each sensor. Interleaved magnetic and acceleration data is available
at ODR rates of up to 400 Hz. FXOS8700CQ is available in a plastic QFN
package and it is guaranteed to operate over the extended temperature
range of –40 °C to +85 °C.

TODO: Trigger and IRQ configuration support

Datasheet:
  http://cache.freescale.com/files/sensors/doc/data_sheet/FXOS8700CQ.pdfSigned-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This adds documentation for the Freescale FXOS8700 Inertial Measurement Unit
device-tree bindings.
Signed-off-by: Robert Jones <rjones@gateworks.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

ad9834_probe misses a check for devm_clk_get and may cause problems.
Add a check like what ad9832 does to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Reduces local boilerplate.
Suggested by coccinelle.
 CHECK   drivers/iio/adc/xilinx-xadc-core.c
drivers/iio/adc/xilinx-xadc-core.c:1184:1-11: WARNING: Use devm_platform_ioremap_resource for xadc -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Manish Narani <manish.narani@xilinx.com>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>

Identified by coccinelle

CHECK   drivers/iio/temperature/maxim_thermocouple.c
drivers/iio/temperature/maxim_thermocouple.c:197:3-4: Unneeded semicolon
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>

Coccinelle noticed:
CHECK   drivers/iio/adc/cpcap-adc.c
drivers/iio/adc/cpcap-adc.c:1009:9-34: ERROR: Threaded IRQ with no primary handler requested without IRQF_ONESHOT

As far as I can see this is a simple case of it should be specified
but isn't.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Avoid local boilerplate.
Suggested by coccinelle via coccicheck.
CHECK   drivers/iio/adc/meson_saradc.c
drivers/iio/adc/meson_saradc.c:1218:1-5: WARNING: Use devm_platform_ioremap_resource for base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Reduce local boilerplate.
Identified by coccinelle
drivers/iio/adc/exynos_adc.c:792:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>

Identified by coccinelle
drivers/iio/adc/exynos_adc.c:654:2-3: Unneeded semicolon
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>

Sparse identified the following
CHECK   drivers/iio/proximity/pulsedlight-lidar-lite-v2.c
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c:144:24: warning: cast to restricted __be16
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c:144:24: warning: cast to restricted __be16
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c:144:24: warning: cast to restricted __be16
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c:144:24: warning: cast to restricted __be16

This cleans up by adding a local variable to hold the value whilst
it is __be16 before applying endian converstion into eventual destination.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>

There is a somewhat interesting mixture of be16 and le16 going on in
this one function.  Changes here formalize that a little more.

CHECK   drivers/iio/pressure/bmp280-core.c
drivers/iio/pressure/bmp280-core.c:215:35: warning: cast to restricted __le16
drivers/iio/pressure/bmp280-core.c:229:37: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:229:37: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:229:37: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:229:37: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:230:36: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:230:36: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:230:36: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:230:36: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:237:37: warning: cast to restricted __le16
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

This clearly has no actual affect but it does show sparse and similar
static analysers that we are doing this intentionally.

CHECK   drivers/iio/gyro/mpu3050-core.c
drivers/iio/gyro/mpu3050-core.c:546:48: warning: incorrect type in assignment (different base types)
drivers/iio/gyro/mpu3050-core.c:546:48:    expected restricted __be16 <noident>
drivers/iio/gyro/mpu3050-core.c:546:48:    got int
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

When breaking up a constant to write to two 8 bit registers
it isn't obvious to sparse that it was intentional.

CHECK   drivers/iio/chemical/sps30.c
drivers/iio/chemical/sps30.c:120:30: warning: cast truncates bits from constant value (8004 becomes 4)

So in the interests of minimising noisy warnings, let us add
a mask.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Tomasz Duszynski <tduszyns@gmail.com>

Nothing stops data being of type __be16, which fixes the warning:

CHECK   drivers/iio/adc/stmpe-adc.c
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: <philippe.schenker@toradex.com>

Fixes the sparse warning:
drivers/iio/adc/mcp320x.c:167:41: warning: incorrect type in argument 1 (different base types)
drivers/iio/adc/mcp320x.c:167:41:    expected restricted __be32 const [usertype] *p
drivers/iio/adc/mcp320x.c:167:41:    got unsigned int [usertype] *<noident>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>

Cleans up the sparse warning:

CHECK   drivers/iio/adc/at91-sama5d2_adc.c
drivers/iio/adc/at91-sama5d2_adc.c:1486:31: warning: Using plain integer as NULL pointer
drivers/iio/adc/at91-sama5d2_adc.c:1509:31: warning: Using plain integer as NULL pointer
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>

The action_get callback returns a Synapse's action mode.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Count data is now always represented as an unsigned integer, while
Signal data is either SIGNAL_LOW or SIGNAL_HIGH. In addition,
clarification changes and additions are made to better explain the
theory of the Generic Counter interface and its use.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The count_read and count_write callbacks are simplified to pass val as
unsigned long rather than as an opaque data structure. The opaque
counter_count_read_value and counter_count_write_value structures,
counter_count_value_type enum, and relevant counter_count_read_value_set
and counter_count_write_value_get functions, are removed as they are no
longer used.

Cc: Patrick Havelange <patrick.havelange@essensium.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: David Lechner <david@lechnology.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Immutable branch as considerable overlap with mfd, power and hwmon.

The AB8500 GPADC driver is indeed a "general purpose ADC" driver,
and while the IIO subsystem did not exist when the driver was
first merged, it is never too late to clean things up and move it
to the right place.

Nowadays IIO provides the right abstractions and interfaces to
do generic ADC work in the kernel.

We have to cut a bunch of debugfs luggage to make this transition
swift, but all these files to is read out the raw values of the
ADC and the IIO subsystem already has a standard sysfs ABI for
doing exactly this: no debugfs is needed.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This is a new driver for the ST-Ericsson AB8500 GPADC, which
replaces the old driver in drivers/mfd/ab8500-gpadc.c and
thus gets rid of another necessarily different custom driver
from the times before IIO existed.

The AB8500 GPADC can convert 10 different channels and these
are used for monitoring voltages in the U8500 chipset, some
are used for battery charging, some for temperature
monitoring.

As this is very core functionality that a lot of drivers
depend on and was formerly compiled in with the AB8500 core
driver, we deafault it to 'y' in Kconfig: it can be compiled
out but it is really not advisible: the platform can
for example overheat if we do.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

As we migrate the AB8500 GPADC driver to use IIO, we need to augment
the bindings to account for defining the ADC channels in the device
tree.

Cc: devicetree@vger.kernel.org
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This switches the AB8500 hardware monitor driver to using
the standard IIO ADC channel lookup and conversion routines.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This switches the AB8500 fuel gauge driver to using
the standard IIO ADC channel lookup and conversion routines.
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This switches the AB8500 battery charger driver to using
the standard IIO ADC channel lookup and conversion routines.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This switches the AB8500 battery temperature driver to using
the standard IIO ADC channel lookup and conversion routines.
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Immutable branch being merged in.  Created as this also involves
moving some dependencies around, outside of the counter subsystem.
It's possible it will want to be pulled into other trees.