- 19 Jun, 2023 6 commits
-
-
Minda Chen authored
StarFive JH7110 platforms USB have a wrapper module around the Cadence USBSS-DRD controller. Add binding information doc for that. Signed-off-by:
Minda Chen <minda.chen@starfivetech.com> Reviewed-by:
Peter Chen <peter.chen@kernel.org> Reviewed-by:
Hal Feng <hal.feng@starfivetech.com> Reviewed-by:
Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20230518112750.57924-6-minda.chen@starfivetech.comSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Varadarajan Narayanan authored
* Document the IPQ9574 dwc3 compatible. * Make power-domains as optional since IPQ9574 doesn't have GDSCs Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Varadarajan Narayanan <quic_varada@quicinc.com> Link: https://lore.kernel.org/r/27fc578e549e12a4d689cdd434107964b529c4f4.1686289721.git.quic_varada@quicinc.comSigned-off-by:
-
Colin Ian King authored
There is a spelling mistake in a trace message. Fix it. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Link: https://lore.kernel.org/r/20230615144052.2254528-1-colin.i.king@gmail.comSigned-off-by:
-
Azeem Shaikh authored
strlcpy() reads the entire source buffer first. This read may exceed the destination size limit. This is both inefficient and can lead to linear read overflows if a source string is not NUL-terminated [1]. In an effort to remove strlcpy() completely [2], replace strlcpy() here with strscpy(). Direct replacement is safe here since return value of -errno is used to check for truncation instead of PAGE_SIZE. [1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy [2] https://github.com/KSPP/linux/issues/89Signed-off-by:
Azeem Shaikh <azeemshaikh38@gmail.com> Link: https://lore.kernel.org/r/20230615180318.400639-1-azeemshaikh38@gmail.comSigned-off-by:
-
Frank Wang authored
Traverse fixed pdos to calculate the maximum power that the charger can provide, and it can be get by POWER_SUPPLY_PROP_INPUT_POWER_LIMIT property. Signed-off-by:
Frank Wang <frank.wang@rock-chips.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20230616075241.27690-2-frank.wang@rock-chips.comSigned-off-by:
-
Frank Wang authored
In the current implementation, the tcpm set CC1/CC2 role to open when it do port reset would cause the VBUS removed by the Type-C partner. This sets CC1/CC2 according to the default state of port to fix it. Signed-off-by:
-
- 15 Jun, 2023 6 commits
-
-
Dmitry Baryshkov authored
Add support for the ON Semiconductor NB7VPQ904M Type-C USB SuperSpeed and DisplayPort ALT Mode Linear Redriver chip found on some devices with a Type-C port. The redriver compensates ultra High-Speeed DisplayPort and USB Super Speed signal integrity losses mainly due to PCB & transmission cables. The redriver doesn't support SuperSpeed lines swapping, but can support Type-C SBU lines swapping. Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by:
Neil Armstrong <neil.armstrong@linaro.org> Message-ID: <20230601-topic-sm8x50-upstream-redriver-v4-2-91d5820f3a03@linaro.org> Signed-off-by:
-
Greg Kroah-Hartman authored
For some reason the include/uapi/linux/usb/ directory is missing in the USB SUBSYSTEM entry, so get_maintainer will not know to cc: the proper mailing lists. Fix this up by adding an entry for this directory. Message-ID: <20230615094306.2072827-2-gregkh@linuxfoundation.org> Signed-off-by: -
Piyush Mehta authored
Convert the binding to DT schema format. It also updates the reset-controller description. Signed-off-by:
Piyush Mehta <piyush.mehta@amd.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Message-ID: <20230613123048.2935502-1-piyush.mehta@amd.com> Signed-off-by:
-
Neil Armstrong authored
Document bindings for this ON Semiconductor Type-C USB SuperSpeed and DisplayPort ALT Mode Linear Redriver. Signed-off-by:
-
Kees Cook authored
Since commit df8fc4e9 ("kbuild: Enable -fstrict-flex-arrays=3"), UBSAN_BOUNDS no longer pretends 1-element arrays are unbounded. Walking wData will trigger a warning, so make it a proper flexible array. Add a union to keep the struct size identical for userspace in case anything was depending on the old size. Reported-by:
kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202306102333.8f5a7443-oliver.sang@intel.com Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: kernel test robot <lkp@intel.com> Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org> Cc: Dan Williams <dan.j.williams@intel.com> Cc: "Jó Ágila Bitsch" <jgilab@gmail.com> Signed-off-by:
Kees Cook <keescook@chromium.org> Message-ID: <20230614181307.gonna.256-kees@kernel.org> Signed-off-by:
-
Greg Kroah-Hartman authored
This reverts commit edd60d24. Heikki reports that this should not be a global flag just to work around one broken driver and should be fixed differently, so revert it. Reported-by:
-
- 13 Jun, 2023 28 commits
-
-
Xu Yang authored
USB PHY DPDM wakeup bit is enabled by default, when USB wakeup is not required(/sys/.../wakeup is disabled), this bit should be disabled, otherwise we will have unexpected wakeup if do USB device connect/disconnect while system sleep. This bit can be enabled for both host and device mode. Signed-off-by:
Li Jun <jun.li@nxp.com> Signed-off-by:
Xu Yang <xu.yang_2@nxp.com> Acked-by:
-
Xu Yang authored
As we use bvalid for vbus wakeup source, to save power when suspend, turn off the vbus comparator for imx7d and imx8mm. Below is this bit description from RM of iMX8MM "VBUS Valid Comparator Enable: This signal controls the USB OTG PHY VBUS Valid comparator which indicates whether the voltage on the USB_OTG*_VBUS pin is below the VBUS Valid threshold. The VBUS Valid threshold is nominally 4.75V on this USB PHY. The VBUS Valid threshold can be adjusted using the USBNC_OTGn_PHY_CFG1[OTGTUNE0] bit field. Status of the VBUS Valid comparator, when it is enabled, is reported on the USBNC_OTGn_PHY_STATUS[VBUS_VLD] bit. When OTGDISABLE0 (USBNC_USB_OTGx_PHY_CFG2[10])is set to 1'b0 and DRVVBUS0 is set to 1'b1, the Bandgap circuitry and VBUS Valid comparator are powered, even in Suspend or Sleep mode. DRVVBUS0 should be reset to 1'b0 when the internal VBUS Valid comparator is not required, to reduce quiescent current in Suspend or Sleep mode. - 0 The VBUS Valid comparator is disabled - 1 The VBUS Valid comparator is enabled" Signed-off-by:
-
Pawel Laszczak authored
Patch adds entry for USBHS (CDNS2) driver into MAINTARNERS file Signed-off-by:
Pawel Laszczak <pawell@cadence.com> Message-ID: <20230602102644.77470-5-pawell@cadence.com> Signed-off-by:
-
Pawel Laszczak authored
Patch adds the series of tracepoints that can be used for debugging issues detected in driver. Signed-off-by:
-
Pawel Laszczak authored
This patch introduces the main part of Cadence USBHS driver to Linux kernel. To reduce the patch size a little bit, the header file gadget.h was intentionally added as separate patch. The Cadence USB 2.0 Controller is a highly configurable IP Core which supports both full and high speed data transfer. The current driver has been validated with FPGA platform. We have support for PCIe bus, which is used on FPGA prototyping. Signed-off-by:
-
Pawel Laszczak authored
Patch defines macros, registers and structures used by Device side driver. Signed-off-by:
-
Christophe JAILLET authored
If dwc3_meson_g12a_otg_init() fails, resources allocated by the previous of_platform_populate() call should be released, as already done in the error handling path. Fixes: 1e355f21 ("usb: dwc3: Add Amlogic A1 DWC3 glue") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by:
-
Jeff Layton authored
In general, POSIX requires that when the mtime is updated that the ctime be updated as well. Add the missing timestamp updates to the usb ioctls. Signed-off-by:
Jeff Layton <jlayton@kernel.org> Message-ID: <20230612104524.17058-3-jlayton@kernel.org> Signed-off-by:
-
Roy Luo authored
Expose usb device state to userland as the information is useful in detecting non-compliant setups and diagnosing enumeration failures. For example: - End-to-end signal integrity issues: the device would fail port reset repeatedly and thus be stuck in POWERED state. - Charge-only cables (missing D+/D- lines): the device would never enter POWERED state as the HC would not see any pullup. What's the status quo? We do have error logs such as "Cannot enable. Maybe the USB cable is bad?" to flag potential setup issues, but there's no good way to expose them to userspace. Why add a sysfs entry in struct usb_port instead of struct usb_device? The struct usb_device is not device_add() to the system until it's in ADDRESS state hence we would miss the first two states. The struct usb_port is a better place to keep the information because its life cycle is longer than the struct usb_device that is attached to the port. Reported-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Roy Luo <royluo@google.com> Message-ID: <20230608015913.1679984-1-royluo@google.com> Signed-off-by:
-
Prashanth K authored
Currently if we bootup a device without cable connected, then usb-conn-gpio won't call set_role() since last_role is same as current role. This happens because during probe last_role gets initialised to zero. To avoid this, added a new constant in enum usb_role, last_role is set to USB_ROLE_UNKNOWN before performing initial detection. While at it, also handle default case for the usb_role switch in cdns3, intel-xhci-usb-role-switch & musb/jz4740 to avoid build warnings. Fixes: 4602f3bf ("usb: common: add USB GPIO based connection detection driver") Signed-off-by:
Prashanth K <quic_prashk@quicinc.com> Reviewed-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Message-ID: <1685544074-17337-1-git-send-email-quic_prashk@quicinc.com> Signed-off-by:
-
Xu Yang authored
Use dedicated imx8ulp usb compatible to remove QoS request since imx8ulp has no such limitation of imx7ulp: DMA will not work if system enters idle. Signed-off-by:
-
Xu Yang authored
The imx8ulp and imx8dxl are compatible. This will add fsl,imx8ulp-usb to the compatible property. Signed-off-by:
-
Andrew Halaney authored
Update to using dev_err_probe() throughout to reduce spam and log useful information in devices_deferred. Signed-off-by:
Andrew Halaney <ahalaney@redhat.com> Message-ID: <20230605193625.63187-1-ahalaney@redhat.com> Signed-off-by:
-
Christophe JAILLET authored
If dwc3_qcom_create_urs_usb_platdev() fails, some resources still need to be released, as already done in the other error handling path of the probe. Fixes: c25c210f ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot") Signed-off-by:
-
Christophe JAILLET authored
In the probe, some resources are allocated with dwc3_qcom_of_register_core() or dwc3_qcom_acpi_register_core(). The corresponding resources are already coorectly freed in the error handling path of the probe, but not in the remove function. Fix it. Fixes: 2bc02355 ("usb: dwc3: qcom: Add support for booting with ACPI") Signed-off-by:
-
David Disseldorp authored
The fsg_lun_is_open() test can be eliminated and the code merged with the preceding conditional, because the LUN won't be open if cfg->filename wasn't set. Similarly, the error_lun label will never be reached with an open lun (non-null filp) so remove the unnecessary fsg_lun_close() call. Signed-off-by:
David Disseldorp <ddiss@suse.de> Reviewed-by:
-
Avichal Rakesh authored
This patch elaborates on some of the edge cases handled by video_pump around setting no_interrupt flag, and brings the code style in line with rest of the file. Link: https://lore.kernel.org/20230602151916.GH26944@pendragon.ideasonboard.com/Signed-off-by:
Avichal Rakesh <arakesh@google.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Message-ID: <20230602220455.313801-1-arakesh@google.com> Signed-off-by:
-
Piyush Mehta authored
Add an identifier in the read_fn function declaration because based on commit ca0d8929 ("checkpatch: add warning for unnamed function definition arguments") it is the preferred coding style even C standard allows both formats. Signed-off-by:
-
Christophe JAILLET authored
Use of_property_read_u16() instead of of_property_read_u16_array() when only 1 element is read. This slightly simplifies the code. Signed-off-by:
-
Kuen-Han Tsai authored
If gs_close has cleared port->port.tty and gs_start_io is called afterwards, then the function tty_wakeup will attempt to access the value of the pointer port->port.tty which will cause a null pointer dereference error. To avoid this, add a null pointer check to gs_start_io before attempting to access the value of the pointer port->port.tty. Signed-off-by:
Kuen-Han Tsai <khtsai@google.com> Message-ID: <20230602070009.1353946-1-khtsai@google.com> Signed-off-by:
-
Rajat Khandelwal authored
IOM status has a crucial role during debugging to check the current state of the type-C port. There are ways to fetch the status, but all those require the IOM port status offset, which could change with platform. Make a debugfs directory for intel_pmc_mux and expose the status under it per port basis. Signed-off-by:
Rajat Khandelwal <rajat.khandelwal@linux.intel.com> Reviewed-by:
-
Weitao Wang authored
Add U1/U2 feature support of xHCI for ZHAOXIN. Since both INTEL and ZHAOXIN need to check the tier where the device is located to determine whether to enabled U1/U2, remove the previous INTEL U1/U2 tier policy and add common policy in xhci_check_tier_policy. If vendor has specific U1/U2 enable policy,quirks can be add to declare. Suggested-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
Weitao Wang <WeitaoWang-oc@zhaoxin.com> Signed-off-by:
-
Weitao Wang authored
Some ZHAOXIN xHCI controllers follow usb3.1 spec, but only support gen1 speed 5Gbps. While in Linux kernel, if xHCI suspport usb3.1, root hub speed will show on 10Gbps. To fix this issue of ZHAOXIN xHCI platforms, read usb speed ID supported by xHCI to determine root hub speed. And add a quirk XHCI_ZHAOXIN_HOST for this issue. [fix warning about uninitialized symbol -Mathias] Suggested-by:
-
Weitao Wang authored
On some ZHAOXIN hosts, xHCI will prefetch TRB for performance improvement. However this TRB prefetch mechanism may cross page boundary, which may access memory not allocated by xHCI driver. In order to fix this issue, two pages was allocated for a segment and only the first page will be used. And add a quirk XHCI_ZHAOXIN_TRB_FETCH for this issue. Cc: stable@vger.kernel.org Signed-off-by:
-
Weitao Wang authored
On ZHAOXIN ZX-100 project, xHCI can't work normally after resume from system Sx state. To fix this issue, when resume from system Sx state, reinitialize xHCI instead of restore. So, Add XHCI_RESET_ON_RESUME quirk for ZX-100 to fix issue of resuming from system Sx state. Cc: stable@vger.kernel.org Signed-off-by:
-
Mathias Nyman authored
Trying to keep track of free trbs in a ring by adding and subtracting deltas each time a enqueue or dequeue is increased or moved has proven to be buggy and complicated, especially over long periods of time. Recently a bug in counting free trbs was fixed, now taking into account cancelled URBs that were turned into no-ops, preventing free_trbs to slowly wander off causing unnecessary ring expansion. See commit fe82f16a ("xhci: Fix incorrect tracking of free space on transfer rings") Turns out its a lot easier to just calculate the numer of free TRB based on ring size and the current enqueue and dequeue pointer values. This is currently only needed for the command ring as multi segment transfer rings already ensures there is enough room the ring during the ring expansion check. We could get rid of the ring->num_trbs_free entry completely, but as the xhci DbC code also uses it we don't clean that up in this patch. Reported-by:
Miller Hunter <MillerH@hearthnhome.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217242Tested-by:
-
Mathias Nyman authored
The amount of new TRBs needed is calculated incorrectly when expanding a transfer ring. The room_on_ring() helper will correctly report that the ring needs expansion if the enqueue pointer is about to reach the dequeue segment. If enqueue reaches the dequeue segment then there is no easy way to expand the ring by adding new segments between enqueue and dequeue. This leads to ring expansion even if num_trbs_free is larger than num_trbs we are queueing. As a result we try to store a negative number in a unsigned int, leading to a huge percieved trb need, and doubling of ring size. Rework and rename the room_on_ring() to a helper that checks if ring needs expansion, and return number of new segments needed. Don't rely on the tracked ring->num_trbs_free value as turns out it has been unreliable. Use ring enqueue and dequeue positions to determine expansion need. The unsigned int issue was first reported first Chao zeng, and a bit later seen in a real world bug. Reported-by:
chao zeng <chao.zengup@gmail.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217242Tested-by:
-
Mathias Nyman authored
The current function that both allocates and adds the interrupter isn't optimal when using several interrupters. The array of interrupters need to be protected with a lock while adding or removing interrupters. If memory is allocated under the default xhci spinlock then GFP_KERNEL can't be used. There is no need to allocate the interrupter memory under the lock, so split this code into separate unlocked allocate part, and a lock protected add part. Signed-off-by:
-
