Card Write-Protect pin is often implemented, using a GPIO, which makes
it simple to provide a generic handler for it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

This prepares for the addition of further slot functions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

A simple extension of mmc slot functions add support for CD GPIO polling
for cases where the GPIO cannot produce interrupts, or where this is not
desired for some reason.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

To handle CD and WP SD/MMC slot pins we need generic flags to specify their
polarity.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

struct mmc_host::hotplug is becoming a generic hook for slot functions.
Rename it accordingly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

Add regulator support to the sh_mmcif driver, but also preserve the current
power-callback.

Also note, that the card power is not switched off during clock gating
periods, hence there's no need to power it on every time the card is
re-activated.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>

From the original version of sh_mmcif the .set_pwr() callback has only been
used to turn the card's power on, and the .down_pwr() callback has been
used to turn it off. .set_pwr() can be used for both these tasks, which is
also how it is implemented by the only user of this API: the SH7724 ecovec
board.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>

With aggressive clock gating the clock can be disabled during interface
inactivity. During this time its frequency can be changed by another its
user. Therefore when the interface is activated again and the clock is
re-enabled, its frequency has to be re-read.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>

Regardless of whether the MMC bus clock is the same as the PM clock on
this specific interface, it has to be managed separately. Its proper
management should also include enabling and disabling of the clock,
whenever the interface is becoming active or going idle respectively.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>

A check for NULL platform data can be conveniently made in the very
beginning of probing. Replace numbered error-handling labels in .probe()
with meaningful names to make any future reorganisation simpler.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

Currently the SDHI glue for the TMIO MMC driver installs dummy .get_cd() and
.set_pwr() callbacks even if the platform didn't supply them. This is not
necessary, since the TMIO MMC driver itself checks for NULL callbacks. This
is also dubious if the platform provides a regulator for SD-card power
switching. It is better to only install those callbacks, if they are really
provided by the platform.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

Currently the TMIO MMC driver derives the OCR mask from the platform data
and uses a platform callback to turn card power on and off. This patch adds
regulator support to the driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Instead of delivering one static clock frequency value, read from the
hardware during probing, enable the tmio-mmc driver to re-read the
frequency dynamically.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

Every time the clock is enabled after possibly being disabled, we have
to re-read its frequency and update our configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

We don't have to force-enable MMC interrupts in our .probe() method,
mmc_add_host() will trigger card detection, that will enable all the
necessary interrupts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

host->dma_ops is not valid if host->usa dma is 0 so protect
host->dma_ops reference in dw_mci_resume
Signed-off-by: Jonathan Kliegman <kliegs@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Add a function to get regulators, supplying card's Vdd and Vccq on a
specific host. If a Vdd supplying regulator is found, the function checks,
whether a valid OCR mask can be obtained from it. The Vccq regulator is
optional. A failure to get it is not fatal.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

The tmio_mmc_set_ios() function configures the MMC power, clock and bus
width. When the mmc core requests the driver to power off the card, we
inform runtime PM, that the controller can be suspended. This can lead
to the MSTP clock being turned off.

Writing to any 16-bit hardware registers with the MSTP clock off leads
to timeouts and errors being printed to the kernel log. This can occur
both when stopping the MMC clock and when configuring the bus width.

To fix this, stop the MMC clock before calling put_runtime_pm(), and
skip bus width configuration when power is off.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

The MMC_SLEEP_AWAKE and SD_IO_SEND_OP_COND commands share the same
opcode. SD_IO_SEND_OP_COND isn't supported by the SH MMCIF, but
MMC_SLEEP_AWAKE is. Discriminate between the two commands using the
command flags, and reject SD_IO_SEND_OP_COND only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

In the current dwmmc driver there is support for selecting IDMAC from
the menu config option. If the support for IDMAC is enabled in the menu
config and the hardware configuration register's DMA_INTERFACE field is
0, the driver will still try to do the DMA initialization.

The dw_mci_idmac_init function currently implemented returns only success
indicating that the DMA initialization is always successful. This patch
adds a check for existence of the DMA IP to allow the DMA initialization.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Tested on an OLPC XO-1.75.  (MMP2, sdhci-pxav3, CONFIG_MACH_MMP2_DT=y)
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>

Even though these aren't parsed by the MMC driver, make clear that
they're required by the OF core.  (Also, a few typo fixes.)
Signed-off-by: Chris Ball <cjb@laptop.org>

Now that we have common bindings for MMC, rewrite the individual
bindings to inherit from mmc.txt and describe their differences.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

The regulator API functions we're wrapping are exported as GPL, so our
wrappers for the same functions should be too.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

For completing any block request, MMC block driver is calling:
	spin_lock_irq(queue)
	__blk_end_request()
	spin_unlock_irq(queue)

But if we analyze the sources of latency in kernel using ftrace,
__blk_end_request() function at times may take up to 6.5ms with
spinlock held and irq disabled.

__blk_end_request() calls couple of functions and ftrace output
shows that blk_update_bidi_request() function is almost taking 6ms.
There are 2 function to end the current request: ___blk_end_request()
and blk_end_request(). Both these functions do same thing except
that blk_end_request() function doesn't take up the spinlock
while calling the blk_update_bidi_request().

This patch replaces all __blk_end_request() calls with
blk_end_request() and __blk_end_request_all() calls with
blk_end_request_all().

Testing done: 20 process concurrent read/write on sd card
and eMMC. Ran this test for almost a day on multicore system
and no errors observed.

This change is not meant for improving MMC throughput; it's basically
about becoming fair to other threads/interrupts in the system. By
holding spin lock and interrupts disabled for longer duration, we
won't allow other threads/interrupts to run at all.  Actually slight
performance degradation at file system level can be expected as we
are not holding the spin lock during blk_update_bidi_request() which
means our mmcqd thread may get preempted for other high priority
thread or any interrupt in the system.

These are performance numbers (100MB file write) with eMMC running
in DDR mode:

Without this patch:
	Name of the Test   Value   Unit
	LMDD Read Test     53.79   MBPS
	LMDD Write Test    18.86   MBPS
	IOZONE  Read Test  51.65   MBPS
	IOZONE  Write Test 24.36   MBPS

With this patch:
	Name of the Test    Value  Unit
	LMDD Read Test      52.94  MBPS
	LMDD Write Test     16.70  MBPS
	IOZONE  Read Test   52.08  MBPS
	IOZONE  Write Test  23.29  MBPS

Read numbers are fine. Write numbers are bit down (especially LMDD
write), may be because write requests normally have large transfer
size and which means there are chances that while mmcq is executing
blk_update_bidi_request(), it may get interrupted by interrupts or
other high priority thread.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

mmc_execute_hpi should send the HPI command only once, and only
if the card is in PRG state.

According to eMMC spec, the command's completion time is
not dependent on OUT_OF_INTERRUPT_TIME. Only the transition
out of PRG STATE is guarded by OUT_OF_INTERRUPT_TIME - which
is defined to begin at the end of sending the command itself.

Specify the default timeout for the actual sending of HPI
command, and then use OUT_OF_INTERRUPT_TIME to wait for
the transition out of PRG state.
Reported-by: Alex Lemberg <Alex.Lemberg@sandisk.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

GPIOs can be used in MMC/SD-card slots not only for hotplug detection, but
also to implement the write-protection pin. Rename cd-gpio helpers to
slot-gpio to make addition of further slot GPIO functions possible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

mmc.h defines macros for most frequently used MMC opcodes. Use them instead
of hard-coded numbers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

Fix a boot regression on Mackerel boards with sh_mobile_sdhi
in existing kernels causing:

genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq XXX

caused by 1c6c6952 (genirq: Reject bogus threaded irq requests).

This is backported from Guennadi's patch:
"mmc: extend and rename cd-gpio helpers to handle more slot GPIO functions"
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

This reverts commit 3d93576e(skip card initialization if
power class selection fails).
Problem has been reported when this is used with eMMC4.41
card with Tegra Platform. Till the issue is root caused,
bus width selection failure should not be treated as fatal.
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-Off-by: Venkatraman S <svenkatr@ti.com>
CC: Ulf Hansson <ulf.hansson@stericsson.com>
CC: Subhash Jadavani <subhashj@codeaurora.org>
CC: Saugata Das <saugata.das@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

48ddbe19 "cgroup: make css->refcnt clearing on cgroup removal
optional" allowed a css to linger after the associated cgroup is
removed.  As a css holds a reference on the cgroup's dentry, it means
that cgroup dentries may linger for a while.

Destroying a superblock which has dentries with positive refcnts is a
critical bug and triggers BUG() in vfs code.  As each cgroup dentry
holds an s_active reference, any lingering cgroup has both its dentry
and the superblock pinned and thus preventing premature release of
superblock.

Unfortunately, after 48ddbe19, there's a small window while
releasing a cgroup which is directly under the root of the hierarchy.
When a cgroup directory is released, vfs layer first deletes the
corresponding dentry and then invokes dput() on the parent, which may
recurse further, so when a cgroup directly below root cgroup is
released, the cgroup is first destroyed - which releases the s_active
it was holding - and then the dentry for the root cgroup is dput().

This creates a window where the root dentry's refcnt isn't zero but
superblock's s_active is.  If umount happens before or during this
window, vfs will see the root dentry with non-zero refcnt and trigger
BUG().

Before 48ddbe19, this problem didn't exist because the last dentry
reference was guaranteed to be put synchronously from rmdir(2)
invocation which holds s_active around the whole process.

Fix it by holding an extra superblock->s_active reference across
dput() from css release, which is the dput() path added by 48ddbe19
and the only one which doesn't hold an extra s_active ref across the
final cgroup dput().
Signed-off-by: Tejun Heo <tj@kernel.org>
LKML-Reference: <4FEEA5CB.8070809@huawei.com>
Reported-by: shyju pv <shyju.pv@huawei.com>
Tested-by: shyju pv <shyju.pv@huawei.com>
Cc: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Li Zefan <lizefan@huawei.com>

This reverts commit fa980ca8.  The
commit was an attempt to fix a race condition where a cgroup hierarchy
may be unmounted with positive dentry reference on root cgroup.  While
the commit made the race condition slightly more difficult to trigger,
the race was still there and could be reliably triggered using a
different test case.

Revert the incorrect fix.  The next commit will describe the race and
fix it correctly.
Signed-off-by: Tejun Heo <tj@kernel.org>
LKML-Reference: <4FEEA5CB.8070809@huawei.com>
Reported-by: shyju pv <shyju.pv@huawei.com>
Cc: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Li Zefan <lizefan@huawei.com>

Pull ARM fixes from Russell King:
 "Last merge window, we had some updates from Al cleaning up the signal
  restart handling.  These have caused some problems on ARM, and while
  Al has some fixes, we have some concerns with Al's patches but we've
  been unsuccesful with discussing this.

  We have got to the point where we need to do something, and we've
  decided that the best solution is to revert the appropriate commits
  until Al is able to reply to us.

  Also included here are four patches to fix warnings that I've noticed
  in my build system, and one fix for kprobes test code."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: fix warning caused by wrongly typed arm_dma_limit
  ARM: fix warnings about atomic64_read
  ARM: 7440/1: kprobes: only test 'sub pc, pc, #1b-2b+8-2' on ARMv6
  ARM: 7441/1: perf: return -EOPNOTSUPP if requested mode exclusion is unavailable
  ARM: 7443/1: Revert "new way of handling ERESTART_RESTARTBLOCK"
  ARM: 7442/1: Revert "remove unused restart trampoline"
  ARM: fix set_domain() macro
  ARM: fix mach-versatile/pci.c warning

Merge tag 'ecryptfs-3.5-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull eCryptfs fixes from Tyler Hicks:
 "Fixes an incorrect access mode check when preparing to open a file in
  the lower filesystem.  This isn't an urgent fix, but it is simple and
  the check was obviously incorrect.

  Also fixes a couple important bugs in the eCryptfs miscdev interface.
  These changes are low risk due to the small number of users that use
  the miscdev interface.  I was able to keep the changes minimal and I
  have some cleaner, more complete changes queued up for the next merge
  window that will build on these patches."

* tag 'ecryptfs-3.5-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Gracefully refuse miscdev file ops on inherited/passed files
  eCryptfs: Fix lockdep warning in miscdev operations
  eCryptfs: Properly check for O_RDONLY flag before doing privileged open

Pull target fixes from Nicholas Bellinger:
 "Two minor target fixes.  There is really nothing exciting and/or
  controversial this time around.

  There's one fix from MDR for a RCU debug warning message within tcm_fc
  code (CC'ed to stable), and a small AC fix for qla_target.c based upon
  a recent Coverity static report.

  Also, there is one other outstanding virtio-scsi LUN scanning bugfix
  that has been uncovered with the in-flight tcm_vhost driver over the
  last days, and that needs to make it into 3.5 final too.  This patch
  has been posted to linux-scsi again here:

    http://marc.info/?l=linux-scsi&m=134160609212542&w=2

  and I've asked James to include it in his next PULL request."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  qla2xxx: print the right array elements in qlt_async_event
  tcm_fc: Resolve suspicious RCU usage warnings

File operations on /dev/ecryptfs would BUG() when the operations were
performed by processes other than the process that originally opened the
file. This could happen with open files inherited after fork() or file
descriptors passed through IPC mechanisms. Rather than calling BUG(), an
error code can be safely returned in most situations.

In ecryptfs_miscdev_release(), eCryptfs still needs to handle the
release even if the last file reference is being held by a process that
didn't originally open the file. ecryptfs_find_daemon_by_euid() will not
be successful, so a pointer to the daemon is stored in the file's
private_data. The private_data pointer is initialized when the miscdev
file is opened and only used when the file is released.

https://launchpad.net/bugs/994247Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>

Based upon Alan's patch from Coverity scan id 793583, these debug
messages in qlt_async_event() should be starting from byte 0, which is
always the Asynchronous Event Status Code from the parent switch statement.

Also, rename reason_code -> login_code following the language used in
2500 FW spec for Port Database Changed (0x8014) -> Port Database Changed
Event Mailbox Register for mailbox[2].
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Use rcu_dereference_protected to tell rcu that the ft_lport_lock
is held during ft_lport_create. This resolved "suspicious RCU usage"
warnings when debugging options are turned on.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Pull two MTD fixes from David Woodhouse:
 - Fix a logic error in OLPC CAFÉ NAND ready() function.
 - Fix regression due to bitflip handling changes.

* tag 'for-linus-20120706' of git://git.infradead.org/linux-mtd:
  mtd: cafe_nand: fix an & vs | mistake
  mtd: nand: initialize bitflip_threshold prior to BBT scanning