The Bluetooth 4.1 specification with Secure Connections support has
just been released and controllers with this feature are still in
an early stage.

A handful of controllers have already support for it, but they do
not always identify this feature correctly. This debugfs entry
allows to tell the kernel that the controller can be treated as
it would fully support Secure Connections.

Using debugfs to force Secure Connections support of course does
not make this feature magically appear in all controllers. This
is a debug functionality for early adopters. Once the majority
of controllers matures this quirk will be removed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

For Secure Connections support and the usage of out-of-band pairing,
it is needed to read the P-256 hash and randomizer or P-192 hash and
randomizer. This change will read P-192 data when Secure Connections
is disabled and P-192 and P-256 data when it is enabled.

The difference is between using HCI Read Local OOB Data and using the
new HCI Read Local OOB Extended Data command. The first one has been
introduced with Bluetooth 2.1 and returns only the P-192 data.

< HCI Command: Read Local OOB Data (0x03|0x0057) plen 0
> HCI Event: Command Complete (0x0e) plen 36
      Read Local OOB Data (0x03|0x0057) ncmd 1
        Status: Success (0x00)
        Hash C from P-192: 975a59baa1c4eee391477cb410b23e6d
        Randomizer R with P-192: 9ee63b7dec411d3b467c5ae446df7f7d

The second command has been introduced with Bluetooth 4.1 and will
return P-192 and P-256 data.

< HCI Command: Read Local OOB Extended Data (0x03|0x007d) plen 0
> HCI Event: Command Complete (0x0e) plen 68
      Read Local OOB Extended Data (0x03|0x007d) ncmd 1
        Status: Success (0x00)
        Hash C from P-192: 6489731804b156fa6355efb8124a1389
        Randomizer R with P-192: 4781d5352fb215b2958222b3937b6026
        Hash C from P-256: 69ef8a928b9d07fc149e630e74ecb991
        Randomizer R with P-256: 4781d5352fb215b2958222b3937b6026

The change for the management interface is transparent and no change
is required for existing userspace. The Secure Connections feature
needs to be manually enabled. When it is disabled, then userspace
only gets the P-192 returned and with Secure Connections enabled,
userspace gets P-192 and P-256 in an extended structure.

It is also acceptable to just ignore the P-256 data since it is not
required to support them. The pairing with out-of-band credentials
will still succeed. However then of course no Secure Connection will
b established.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The link keys that are loaded by userspace during controller setup
should be limited to actual valid and supported types. With the
support for Secure Connections, it is limited to types 0x00 - 0x08
at the moment. Reject any other link key types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

If support for Secure Connection has been configured, then make sure
to send the appropiate HCI command to enable it when powering on the
controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The support for Secure Connections need to be explicitly enabled by
userspace. This is required since only userspace that can handle the
new link key types should enable support for Secure Connections.

This command handling is similar to how Secure Simple Pairing enabling
is done. It also tracks the case when Secure Connections support is
enabled via raw HCI commands. This makes sure that the host features
page is updated as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The MGMT_SETTING_SECURE_CONN setting is used to track the support and
status for Secure Connections from the management interface. For HCI
based tracking HCI_SC_ENABLED flag is used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

With Secure Connections capable controllers, the authenticated payload
timeout can trigger. Enable the event so the controller informs the
host when this happens.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Before being able to enable Secure Connections support, the core needs
to know on how to handle P-256 derived link keys. The difference between
authenticated and unauthenticated P-256 derived link keys is the same as
its P-192 counter parts.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

With the introduction of Secure Connections, the list of link key types
got extended by P-256 versions of authenticated and unauthenticated
link keys.

To avoid any confusion the previous authenticated and unauthenticated
link key types got ammended with a P912 postfix. And the two new keys
have a P256 postfix now. Existing code using the previous definitions
has been adjusted.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The Secure Connections feature introduces the support for P-256 strength
pairings (compared to P-192 with Secure Simple Pairing). This however
means that for out-of-band pairing the hash and randomizer needs to be
differentiated. Two new commands are introduced to handle the possible
combinations of P-192 and P-256. This add the HCI command definition
for both.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The Secure Connections feature is optional and host stacks have to
manually enable it. This add the HCI command definiton for reading
and writing this setting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The support for Secure Connections introduces two new controller
features and one new host feature.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The check for HIGH security level dates back to pre-mgmt times when a
raw L2CAP socket with HIGH security level was used to trigger dedicated
bonding. For legacy pairing checking for the security level was the only
way to catch the need to authenticate in all scenarios. With mgmt
however, the pair_device command does not use HIGH security but MEDIUM
security. Therefore, the existing code would never trigger
authentication for a non-SSP connection without an MITM requirement
(e.g. if user space provided a NoInputNoOutput IO capability). In such a
scenario the mgmt_pair_device command would return success without
actually triggering any kind of pairing.

This patch updates the authentication requirement check to also consider
MEDIUM security level, and thereby ensures that mgmt_pair_device will
always trigger authentication.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds key material V2 support to mwifiex.
Newer FW supports this feature and FW KEY API version is used
to determine which command structure needs to be used.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds support to parse FW API version TLVs.
Currently only API version for key_material is supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During deauthenticate/link lost event, disable all TDLS links as
TDLS would not work when infra connection is not active.
Also this will avoid an issue where ping to peer station doesn't
work after reassociation to AP where we had created TDLS link in
earlier association.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If TDLS link is 11ac enabled i.e. we as well as peer station
supports VHT, configure seprate TX & RX window sizes during
BA setup. So even if BSS does not support 11ac, we can use VHT
capabilities and higher window sizes on direct link.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During TDLS setup request/response, if HW is 11ac capable,
we add VHT Capability IEs in outgoing data frame. Also while
processing received setup request/response, we preserve peer's
11ac capability retrieved from IEs.

Patch also gets VHT parameters from config_station handlers and
sets it to FW using TDLS config command.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch changes mwifiex_fill_vht_cap_tlv function to pass
struct ieee80211_vht_cap instead of mwifiex_ie_types_vhtcap
so that it can be used generically.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds AMPDU support for TDLS link. We have set 11n
capabilities including AMPDU parameters during ENABLE_LINK.
We set a variable in RA list to indicate this as TDLS link.
This patch uses these capabilities to know if AMPDU is allowed
on TDLS link and enables AMPDU aggregation for TX and RX reording
support for RA list for this peer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1. If data packet is addressed to TDLS peer for which link is
established, mark these packets with TDLS flag so that FW can
send them on direct link instead of sending via AP.
2. If data packet is addressed to TDLS peer and TDLS setup is
underway, move these packets to TDLS queue.
3. If this packet is TDLS setup packet, do not block it.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While TDLS link is being setup, few packets from this station to
peer station may be buffered at AP. It may happen that once TDLS
link is setup, packets sent from station to peer on direct link
get delivered before traffic from AP arrives at peer station.
This results into packet reordering issue at peer station.

To avoid this, we hold data packets destined to TDLS peer during
TDLS setup. These packets are moved to temperory TDLS TX queue.
Upon successful TDLS setup, they are moved to RA list created for
this peer. Upon failure, packets are moved back to AP's RA list
for that particular TID.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds cfg80211 change_station handler support for mwifiex
which is needed for TDLS link setup. Driver creates a command to
modify peer link capabilities and issues command to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds cfg80211 add_station handler support for mwifiex
which is needed for TDLS setup. Driver issues create TDLS link
command to FW upon receiving add_station from cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds cfg80211 handler tdls_oper handler support to
mwifiex. Upon enable link, driver sets status as TDLS status as
setup complete and also sets AMSDU size, AMPDU params for direct
link. Upon disable link, driver issues command to FW to delete
this link in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds support for parsing TDLS action frames during
station receive handler.
Peer station capabilities are stored into station node.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds support for TDLS management frames transmit
handler. mwifiex driver supports TDLS with external support,
i.e. expects user space application to form TDLS frames.
Same is advertised to cfg80211 during registration.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Pass 'struct ieee80211_ht_cap' pointer to
mwifiex_fill_cap_info() instead of
'struct mwifiex_ie_types_htcap' pointer, because the routine
internally uses the later one.
This patch also adds WARN_ON_ONCE check for NULL band.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These functions are now needed by TDLS while managing station list.
Move them from AP related file to utility file.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

tos_to_tid_inv values are needed even during TDLS restore
operations. Currently tos_to_tid_inv is part of wmm.c and
is declared static.
Make it part of private structure so that it can be used in
other files as well.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a bug where we were checking for AP's AMPDU param
setting even when transmitting traffic to associated station.
Patch adds provision to pass additional parameter ra_list pointer
to function which checks if AMPDU is allowed. If current BSS type is
AP, we check station's AMPDU params else we check AP's AMPDU params.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently MU/SU beamformer and MU beamformee features are
not supported.

Hence this patch modifies VHT capability information accordingly.
Number of sounding dimensions should be zero in this case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch makes sure that beamforming capability field in
ht capability info gets filled if hardware supports the feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The current mwifiex pcie driver assumed that it would get
its cmdrsp_complete() callback called before another command
was sent to unmap the command's skbuff. However, that is not
true. The mwifiex_check_ps_cond() will send a sleep command
to the card without having adapter->curr_cmd set. Within the
workqueue's state machine the adapter's state would be set
to allow commands (curr_cmd = NULL && cmd_sent = false) after
having receieved the response from the sleep command. The
card->cmd_buf would then be overridden with the new command
but the first command's skbuff was not unmapped. This leaks
mapped skbuffs when a bounce buffer is employed.

To rectify this unmap the card->cmd_buf when the response is
received from the card instead of waiting for the
cmdrsp_complete() callback.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Depending on the underlying DMA implementation its
not possible to partially unmap DMA buffers. Moreover
its not possible to understand the intent of passing
0 as the size to dma unmap. The intent of this
driver is unmap the entire skb buffer. The only way
to ensure that the size matches on unmap is to store
both the dma address and the size in the skb ca field.

Introduce a mwifiex_dma_mapping structure which tracks
the dma address and the size. Additionally, provide
a mwifiex_unmap_pci_memory() that utilizes the new
structure. This also provide symmetry within the
internal API.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In extended scan, host gets scan results through one or
multiple events instead of scan command response. Host will
send next scan command when all the events are received.

Legacy scan sometimes truncates scan results in a noisy
environment due to buffer length limitation. This issue
is addressed in extended scan.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This new function will be useful later for extended scan
feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This new function will be useful later for extended scan
feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

'mwifiex_bcn_param' structure contains five parameters which
are present in beacon buffer in case of legacy scan.

'rssi' field won't be there in this buffer for extended scan.
Hence 'bssid' and 'rssi' are removed from the structure and it is
renamed as 'mwifiex_fixed_bcn_param' so that we can have common
parsing logic later for both.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bit12 in fw_cap_info is for testing only.
Remove all related code.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>