- 14 Mar, 2019 40 commits
-
-
Sebastian Andrzej Siewior authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 53bc8d2a ] During sendmsg() a cloned skb is saved via dp83640_txtstamp() in ->tx_queue. After the NIC sends this packet, the PHY will reply with a timestamp for that TX packet. If the cable is pulled at the right time I don't see that packet. It might gets flushed as part of queue shutdown on NIC's side. Once the link is up again then after the next sendmsg() we enqueue another skb in dp83640_txtstamp() and have two on the list. Then the PHY will send a reply and decode_txts() attaches it to the first skb on the list. No crash occurs since refcounting works but we are one packet behind. linuxptp/ptp4l usually closes the socket and opens a new one (in such a timeout case) so those "stale" replies never get there. However it does not resume normal operation anymore. Purge old skbs in decode_txts(). Fixes: cb646e2b ("ptp: Added a clock driver for the National Semiconductor PHYTER.") Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by:
Kurt Kanzenbach <kurt@linutronix.de> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Juerg Haefliger <juergh@canonical.com> Signed-off-by:
Khalid Elmously <khalid.elmously@canonical.com>
-
Govindarajulu Varadarajan authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 7596175e ] In case of IPv6 pkts, ipv4_csum_ok is 0. Because of this, driver does not set skb->ip_summed. So IPv6 rx checksum is not offloaded. Signed-off-by:
Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by:
-
Eric Dumazet authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 9b1f19d8 ] Similarly to commit 276bdb82 ("dccp: check ccid before dereferencing") it is wise to test for a NULL ccid. kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] PREEMPT SMP KASAN CPU: 1 PID: 16 Comm: ksoftirqd/1 Not tainted 5.0.0-rc3+ #37 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:ccid_hc_tx_parse_options net/dccp/ccid.h:205 [inline] RIP: 0010:dccp_parse_options+0x8d9/0x12b0 net/dccp/options.c:233 Code: c5 0f b6 75 b3 80 38 00 0f 85 d6 08 00 00 48 b9 00 00 00 00 00 fc ff df 48 8b 45 b8 4c 8b b8 f8 07 00 00 4c 89 f8 48 c1 e8 03 <80> 3c 08 00 0f 85 95 08 00 00 48 b8 00 00 00 00 00 fc ff df 4d 8b kobject: 'loop5' (0000000080f78fc1): kobject_uevent_env RSP: 0018:ffff8880a94df0b8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8880858ac723 RCX: dffffc0000000000 RDX: 0000000000000100 RSI: 0000000000000007 RDI: 0000000000000001 RBP: ffff8880a94df140 R08: 0000000000000001 R09: ffff888061b83a80 R10: ffffed100c370752 R11: ffff888061b83a97 R12: 0000000000000026 R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8880ae700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f0defa33518 CR3: 000000008db5e000 CR4: 00000000001406e0 kobject: 'loop5' (0000000080f78fc1): fill_kobj_path: path = '/devices/virtual/block/loop5' DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: dccp_rcv_state_process+0x2b6/0x1af6 net/dccp/input.c:654 dccp_v4_do_rcv+0x100/0x190 net/dccp/ipv4.c:688 sk_backlog_rcv include/net/sock.h:936 [inline] __sk_receive_skb+0x3a9/0xea0 net/core/sock.c:473 dccp_v4_rcv+0x10cb/0x1f80 net/dccp/ipv4.c:880 ip_protocol_deliver_rcu+0xb6/0xa20 net/ipv4/ip_input.c:208 ip_local_deliver_finish+0x23b/0x390 net/ipv4/ip_input.c:234 NF_HOOK include/linux/netfilter.h:289 [inline] NF_HOOK include/linux/netfilter.h:283 [inline] ip_local_deliver+0x1f0/0x740 net/ipv4/ip_input.c:255 dst_input include/net/dst.h:450 [inline] ip_rcv_finish+0x1f4/0x2f0 net/ipv4/ip_input.c:414 NF_HOOK include/linux/netfilter.h:289 [inline] NF_HOOK include/linux/netfilter.h:283 [inline] ip_rcv+0xed/0x620 net/ipv4/ip_input.c:524 __netif_receive_skb_one_core+0x160/0x210 net/core/dev.c:4973 __netif_receive_skb+0x2c/0x1c0 net/core/dev.c:5083 process_backlog+0x206/0x750 net/core/dev.c:5923 napi_poll net/core/dev.c:6346 [inline] net_rx_action+0x76d/0x1930 net/core/dev.c:6412 __do_softirq+0x30b/0xb11 kernel/softirq.c:292 run_ksoftirqd kernel/softirq.c:654 [inline] run_ksoftirqd+0x8e/0x110 kernel/softirq.c:646 smpboot_thread_fn+0x6ab/0xa10 kernel/smpboot.c:164 kthread+0x357/0x430 kernel/kthread.c:246 ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352 Modules linked in: ---[ end trace 58a0ba03bea2c376 ]--- RIP: 0010:ccid_hc_tx_parse_options net/dccp/ccid.h:205 [inline] RIP: 0010:dccp_parse_options+0x8d9/0x12b0 net/dccp/options.c:233 Code: c5 0f b6 75 b3 80 38 00 0f 85 d6 08 00 00 48 b9 00 00 00 00 00 fc ff df 48 8b 45 b8 4c 8b b8 f8 07 00 00 4c 89 f8 48 c1 e8 03 <80> 3c 08 00 0f 85 95 08 00 00 48 b8 00 00 00 00 00 fc ff df 4d 8b RSP: 0018:ffff8880a94df0b8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8880858ac723 RCX: dffffc0000000000 RDX: 0000000000000100 RSI: 0000000000000007 RDI: 0000000000000001 RBP: ffff8880a94df140 R08: 0000000000000001 R09: ffff888061b83a80 R10: ffffed100c370752 R11: ffff888061b83a97 R12: 0000000000000026 R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8880ae700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f0defa33518 CR3: 0000000009871000 CR4: 00000000001406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by:
-
Tejun Heo authored
BugLink: https://bugs.launchpad.net/bugs/1818813 commit 08a77676 upstream. e7fd37ba ("cgroup: avoid copying strings longer than the buffers") converted possibly unsafe strncpy() usages in cgroup to strscpy(). However, although the callsites are completely fine with truncated copied, because strscpy() is marked __must_check, it led to the following warnings. kernel/cgroup/cgroup.c: In function ‘cgroup_file_name’: kernel/cgroup/cgroup.c:1400:10: warning: ignoring return value of ‘strscpy’, declared with attribute warn_unused_result [-Wunused-result] strscpy(buf, cft->name, CGROUP_FILE_NAME_MAX); ^ To avoid the warnings, 50034ed4 ("cgroup: use strlcpy() instead of strscpy() to avoid spurious warning") switched them to strlcpy(). strlcpy() is worse than strlcpy() because it unconditionally runs strlen() on the source string, and the only reason we switched to strlcpy() here was because it was lacking __must_check, which doesn't reflect any material differences between the two function. It's just that someone added __must_check to strscpy() and not to strlcpy(). These basic string copy operations are used in variety of ways, and one of not-so-uncommon use cases is safely handling truncated copies, where the caller naturally doesn't care about the return value. The __must_check doesn't match the actual use cases and forces users to opt for inferior variants which lack __must_check by happenstance or spread ugly (void) casts. Remove __must_check from strscpy() and restore strscpy() usages in cgroup. Signed-off-by:
Tejun Heo <tj@kernel.org> Suggested-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Ma Shimiao <mashimiao.fnst@cn.fujitsu.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Chris Metcalf <cmetcalf@ezchip.com> [backport only the string.h portion to remove build warnings starting to show up - gregkh] Signed-off-by:
-
Guoqing Jiang authored
BugLink: https://bugs.launchpad.net/bugs/1818813 commit 29e270fc upstream. Got below warning with gcc 8.2 compiler. net/tipc/topsrv.c: In function ‘tipc_topsrv_start’: net/tipc/topsrv.c:660:2: warning: ‘strncpy’ specified bound depends on the length of the source argument [-Wstringop-overflow=] strncpy(srv->name, name, strlen(name) + 1); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ net/tipc/topsrv.c:660:27: note: length computed here strncpy(srv->name, name, strlen(name) + 1); ^~~~~~~~~~~~ So change it to correct length and use strscpy. Signed-off-by:
Guoqing Jiang <gqjiang@suse.com> Acked-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
-
Linus Torvalds authored
BugLink: https://bugs.launchpad.net/bugs/1818813 commit b1286ed7 upstream. New versions of gcc reasonably warn about the odd pattern of strncpy(p, q, strlen(q)); which really doesn't make sense: the strncpy() ends up being just a slow and odd way to write memcpy() in this case. Apparently there was a patch for this floating around earlier, but it got lost. Acked-again-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Eduardo Valentin authored
BugLink: https://bugs.launchpad.net/bugs/1818813 commit 03334ba8 upstream. Avoid warnings like this: thermal_hwmon.h:29:1: warning: ‘thermal_remove_hwmon_sysfs’ defined but not used [-Wunused-function] thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz) Fixes: 0dd88793 ("thermal: hwmon: move hwmon support to single file") Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Eduardo Valentin <edubezval@gmail.com> Signed-off-by:
-
Oleg Nesterov authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 8099b047 ] load_script() simply truncates bprm->buf and this is very wrong if the length of shebang string exceeds BINPRM_BUF_SIZE-2. This can silently truncate i_arg or (worse) we can execute the wrong binary if buf[2:126] happens to be the valid executable path. Change load_script() to return ENOEXEC if it can't find '\n' or zero in bprm->buf. Note that '\0' can come from either prepare_binprm()->memset() or from kernel_read(), we do not care. Link: http://lkml.kernel.org/r/20181112160931.GA28463@redhat.comSigned-off-by:
Oleg Nesterov <oleg@redhat.com> Acked-by:
Kees Cook <keescook@chromium.org> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Ben Woodard <woodard@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Sasha Levin <sashal@kernel.org> Signed-off-by:
-
Davidlohr Bueso authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 76699a67 ] The ep->ovflist is a secondary ready-list to temporarily store events that might occur when doing sproc without holding the ep->wq.lock. This accounts for every time we check for ready events and also send events back to userspace; both callbacks, particularly the latter because of copy_to_user, can account for a non-trivial time. As such, the unlikely() check to see if the pointer is being used, seems both misleading and sub-optimal. In fact, we go to an awful lot of trouble to sync both lists, and populating the ovflist is far from an uncommon scenario. For example, profiling a concurrent epoll_wait(2) benchmark, with CONFIG_PROFILE_ANNOTATED_BRANCHES shows that for a two threads a 33% incorrect rate was seen; and when incrementally increasing the number of epoll instances (which is used, for example for multiple queuing load balancing models), up to a 90% incorrect rate was seen. Similarly, by deleting the prediction, 3% throughput boost was seen across incremental threads. Link: http://lkml.kernel.org/r/20181108051006.18751-4-dave@stgolabs.netSigned-off-by:
Davidlohr Bueso <dbueso@suse.de> Reviewed-by:
-
Tetsuo Handa authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 304ae427 ] check_hung_uninterruptible_tasks() is currently calling rcu_lock_break() for every 1024 threads. But check_hung_task() is very slow if printk() was called, and is very fast otherwise. If many threads within some 1024 threads called printk(), the RCU grace period might be extended enough to trigger RCU stall warnings. Therefore, calling rcu_lock_break() for every some fixed jiffies will be safer. Link: http://lkml.kernel.org/r/1544800658-11423-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jpSigned-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Acked-by:
Paul E. McKenney <paulmck@linux.ibm.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
-
Aditya Pakki authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 6ae16dfb ] In lenovo_probe_tpkbd(), the function of_led_classdev_register() could return an error value that is unchecked. The fix adds these checks. Signed-off-by:
Aditya Pakki <pakki001@umn.edu> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Finn Thain authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 296dcc40 ] When the block device is opened with FMODE_EXCL, ref_count is set to -1. This value doesn't get reset when the device is closed which means the device cannot be opened again. Fix this by checking for refcount <= 0 in the release method. Reported-and-tested-by:
Stan Johnson <userm57@yahoo.com> Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Wenwen Wang authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 093c4821 ] In probe_gdrom(), the buffer pointed by 'gd.cd_info' is allocated through kzalloc() and is used to hold the information of the gdrom device. To register and unregister the device, the pointer 'gd.cd_info' is passed to the functions register_cdrom() and unregister_cdrom(), respectively. However, this buffer is not freed after it is used, which can cause a memory leak bug. This patch simply frees the buffer 'gd.cd_info' in exit_gdrom() to fix the above issue. Signed-off-by:
Wenwen Wang <wang6495@umn.edu> Signed-off-by:
-
Jia-Ju Bai authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 7418e652 ] In drivers/isdn/hisax/hfc_pci.c, the functions hfcpci_interrupt() and HFCPCI_l1hw() may be concurrently executed. HFCPCI_l1hw() line 1173: if (!cs->tx_skb) hfcpci_interrupt() line 942: spin_lock_irqsave(); line 1066: dev_kfree_skb_irq(cs->tx_skb); Thus, a possible concurrency use-after-free bug may occur in HFCPCI_l1hw(). To fix these bugs, the calls to spin_lock_irqsave() and spin_unlock_irqrestore() are added in HFCPCI_l1hw(), to protect the access to cs->tx_skb. Signed-off-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by:
-
Junxiao Bi authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 70306d9d ] For sync io read in ocfs2_read_blocks_sync(), first clear bh uptodate flag and submit the io, second wait io done, last check whether bh uptodate, if not return io error. If two sync io for the same bh were issued, it could be the first io done and set uptodate flag, but just before check that flag, the second io came in and cleared uptodate, then ocfs2_read_blocks_sync() for the first io will return IO error. Indeed it's not necessary to clear uptodate flag, as the io end handler end_buffer_read_sync() will set or clear it based on io succeed or failed. The following message was found from a nfs server but the underlying storage returned no error. [4106438.567376] (nfsd,7146,3):ocfs2_get_suballoc_slot_bit:2780 ERROR: read block 1238823695 failed -5 [4106438.567569] (nfsd,7146,3):ocfs2_get_suballoc_slot_bit:2812 ERROR: status = -5 [4106438.567611] (nfsd,7146,3):ocfs2_test_inode_bit:2894 ERROR: get alloc slot and bit failed -5 [4106438.567643] (nfsd,7146,3):ocfs2_test_inode_bit:2932 ERROR: status = -5 [4106438.567675] (nfsd,7146,3):ocfs2_get_dentry:94 ERROR: test inode bit failed -5 Same issue in non sync read ocfs2_read_blocks(), fixed it as well. Link: http://lkml.kernel.org/r/20181121020023.3034-4-junxiao.bi@oracle.comSigned-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by:
Changwei Ge <ge.changwei@h3c.com> Reviewed-by:
Yiwen Jiang <jiangyiwen@huawei.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Jun Piao <piaojun@huawei.com> Cc: Mark Fasheh <mfasheh@versity.com> Signed-off-by:
-
Marc Zyngier authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 67a28de4 ] Running something like: decodecode vmlinux . leads to interested results where not only the leading "." gets stripped from the displayed paths, but also anywhere in the string, displaying something like: kvm_vcpu_check_block (arch/arm64/kvm/virt/kvm/kvm_mainc:2141) which doesn't help further processing. Fix it by only stripping the base path if it is a prefix of the path. Link: http://lkml.kernel.org/r/20181210174659.31054-3-marc.zyngier@arm.comSigned-off-by:
Marc Zyngier <marc.zyngier@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Kangjie Lu authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 26fd962b ] niu_pci_eeprom_read() may fail, so we should check its return value before using the read data. Signed-off-by:
Kangjie Lu <kjlu@umn.edu> Acked-by:
Shannon Nelson <shannon.lee.nelson@gmail.com> Signed-off-by:
-
Anton Ivanov authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 8892d854 ] Changing protection is a very high cost operation in UML because in addition to an extra syscall it also interrupts mmap merge sequences generated by the tlb. While the condition is not particularly common it is worth avoiding. Signed-off-by:
Anton Ivanov <anton.ivanov@cambridgegreys.com> Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
Ronnie Sahlberg authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 59a63e47 ] RHBZ: 1021460 There is an issue where when multiple threads open/close the same directory ntwrk_buf_start might end up being NULL, causing the call to smbCalcSize later to oops with a NULL deref. The real bug is why this happens and why this can become NULL for an open cfile, which should not be allowed. This patch tries to avoid a oops until the time when we fix the underlying issue. Signed-off-by:
Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
Nathan Chancellor authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 5ac93f80 ] Clang warns when one enumerated type is implicitly converted to another: drivers/crypto/ux500/hash/hash_core.c:169:4: warning: implicit conversion from enumeration type 'enum dma_data_direction' to different enumeration type 'enum dma_transfer_direction' [-Wenum-conversion] direction, DMA_CTRL_ACK | DMA_PREP_INTERRUPT); ^~~~~~~~~ 1 warning generated. dmaengine_prep_slave_sg expects an enum from dma_transfer_direction. We know that the only direction supported by this function is DMA_TO_DEVICE because of the check at the top of this function so we can just use the equivalent value from dma_transfer_direction. DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1 Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Nathan Chancellor authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 9d880c59 ] Clang warns when one enumerated type is implicitly converted to another: drivers/crypto/ux500/cryp/cryp_core.c:559:5: warning: implicit conversion from enumeration type 'enum dma_data_direction' to different enumeration type 'enum dma_transfer_direction' [-Wenum-conversion] direction, DMA_CTRL_ACK); ^~~~~~~~~ drivers/crypto/ux500/cryp/cryp_core.c:583:5: warning: implicit conversion from enumeration type 'enum dma_data_direction' to different enumeration type 'enum dma_transfer_direction' [-Wenum-conversion] direction, ^~~~~~~~~ 2 warnings generated. dmaengine_prep_slave_sg expects an enum from dma_transfer_direction. Because we know the value of the dma_data_direction enum from the switch statement, we can just use the proper value from dma_transfer_direction so there is no more conversion. DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1 DMA_FROM_DEVICE = DMA_DEV_TO_MEM = 2 Signed-off-by:
-
Michael Ellerman authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 0464ed24 ] Currently seq_buf_puts() will happily create a non null-terminated string for you in the buffer. This is particularly dangerous if the buffer is on the stack. For example: char buf[8]; char secret = "secret"; struct seq_buf s; seq_buf_init(&s, buf, sizeof(buf)); seq_buf_puts(&s, "foo"); printk("Message is %s\n", buf); Can result in: Message is fooªªªªªsecret We could require all users to memset() their buffer to zero before use. But that seems likely to be forgotten and lead to bugs. Instead we can change seq_buf_puts() to always leave the buffer in a null-terminated state. The only downside is that this makes the buffer 1 character smaller for seq_buf_puts(), but that seems like a good trade off. Link: http://lkml.kernel.org/r/20181019042109.8064-1-mpe@ellerman.id.auAcked-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Kangjie Lu authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 9aa3aa15 ] In lm80_probe(), if lm80_read_value() fails, it returns a negative error number which is stored to data->fan[f_min] and will be further used. We should avoid using the data if the read fails. The fix checks if lm80_read_value() fails, and if so, returns with the error number. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Kangjie Lu authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit c9c63915 ] If lm80_read_value() fails, it returns a negative number instead of the correct read data. Therefore, we should avoid using the data if it fails. The fix checks if lm80_read_value() fails, and if so, returns with the error number. Signed-off-by:
-
Chris Perl authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 594d1644 ] This patch removes the check from nfs_compare_mount_options to see if a `sec' option was passed for the current mount before comparing auth flavors and instead just always compares auth flavors. Consider the following scenario: You have a server with the address 192.168.1.1 and two exports /export/a and /export/b. The first export supports `sys' and `krb5' security, the second just `sys'. Assume you start with no mounts from the server. The following results in EIOs being returned as the kernel nfs client incorrectly thinks it can share the underlying `struct nfs_server's: $ mkdir /tmp/{a,b} $ sudo mount -t nfs -o vers=3,sec=krb5 192.168.1.1:/export/a /tmp/a $ sudo mount -t nfs -o vers=3 192.168.1.1:/export/b /tmp/b $ df >/dev/null df: ‘/tmp/b’: Input/output error Signed-off-by:
Chris Perl <cperl@janestreet.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit e87555e5 ] AMD doesn't seem to implement MSR_IA32_MCG_EXT_CTL and svm code in kvm knows nothing about it, however, this MSR is among emulated_msrs and thus returned with KVM_GET_MSR_INDEX_LIST. The consequent KVM_GET_MSRS, of course, fails. Report the MSR as unsupported to not confuse userspace. Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Noralf Trønnes authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 2122b405 ] When unregistering fbdev using unregister_framebuffer(), any bound console will unbind automatically. This is working fine if this is the only framebuffer, resulting in a switch to the dummy console. However if there is a fb0 and I unregister fb1 having a bound console, I eventually get a crash. The fastest way for me to trigger the crash is to do a reboot, resulting in this splat: [ 76.478825] WARNING: CPU: 0 PID: 527 at linux/kernel/workqueue.c:1442 __queue_work+0x2d4/0x41c [ 76.478849] Modules linked in: raspberrypi_hwmon gpio_backlight backlight bcm2835_rng rng_core [last unloaded: tinydrm] [ 76.478916] CPU: 0 PID: 527 Comm: systemd-udevd Not tainted 4.20.0-rc4+ #4 [ 76.478933] Hardware name: BCM2835 [ 76.478949] Backtrace: [ 76.478995] [<c010d388>] (dump_backtrace) from [<c010d670>] (show_stack+0x20/0x24) [ 76.479022] r6:00000000 r5:c0bc73be r4:00000000 r3:6fb5bf81 [ 76.479060] [<c010d650>] (show_stack) from [<c08e82f4>] (dump_stack+0x20/0x28) [ 76.479102] [<c08e82d4>] (dump_stack) from [<c0120070>] (__warn+0xec/0x12c) [ 76.479134] [<c011ff84>] (__warn) from [<c01201e4>] (warn_slowpath_null+0x4c/0x58) [ 76.479165] r9:c0eb6944 r8:00000001 r7:c0e927f8 r6:c0bc73be r5:000005a2 r4:c0139e84 [ 76.479197] [<c0120198>] (warn_slowpath_null) from [<c0139e84>] (__queue_work+0x2d4/0x41c) [ 76.479222] r6:d7666a00 r5:c0e918ee r4:dbc4e700 [ 76.479251] [<c0139bb0>] (__queue_work) from [<c013a02c>] (queue_work_on+0x60/0x88) [ 76.479281] r10:c0496bf8 r9:00000100 r8:c0e92ae0 r7:00000001 r6:d9403700 r5:d7666a00 [ 76.479298] r4:20000113 [ 76.479348] [<c0139fcc>] (queue_work_on) from [<c0496c28>] (cursor_timer_handler+0x30/0x54) [ 76.479374] r7:d8a8fabc r6:c0e08088 r5:d8afdc5c r4:d8a8fabc [ 76.479413] [<c0496bf8>] (cursor_timer_handler) from [<c0178744>] (call_timer_fn+0x100/0x230) [ 76.479435] r4:c0e9192f r3:d758a340 [ 76.479465] [<c0178644>] (call_timer_fn) from [<c0178980>] (expire_timers+0x10c/0x12c) [ 76.479495] r10:40000000 r9:c0e9192f r8:c0e92ae0 r7:d8afdccc r6:c0e19280 r5:c0496bf8 [ 76.479513] r4:d8a8fabc [ 76.479541] [<c0178874>] (expire_timers) from [<c0179630>] (run_timer_softirq+0xa8/0x184) [ 76.479570] r9:00000001 r8:c0e19280 r7:00000000 r6:c0e08088 r5:c0e1a3e0 r4:c0e19280 [ 76.479603] [<c0179588>] (run_timer_softirq) from [<c0102404>] (__do_softirq+0x1ac/0x3fc) [ 76.479632] r10:c0e91680 r9:d8afc020 r8:0000000a r7:00000100 r6:00000001 r5:00000002 [ 76.479650] r4:c0eb65ec [ 76.479686] [<c0102258>] (__do_softirq) from [<c0124d10>] (irq_exit+0xe8/0x168) [ 76.479716] r10:d8d1a9b0 r9:d8afc000 r8:00000001 r7:d949c000 r6:00000000 r5:c0e8b3f0 [ 76.479734] r4:00000000 [ 76.479764] [<c0124c28>] (irq_exit) from [<c016b72c>] (__handle_domain_irq+0x94/0xb0) [ 76.479793] [<c016b698>] (__handle_domain_irq) from [<c01021dc>] (bcm2835_handle_irq+0x3c/0x48) [ 76.479823] r8:d8afdebc r7:d8afddfc r6:ffffffff r5:c0e089f8 r4:d8afddc8 r3:d8afddc8 [ 76.479851] [<c01021a0>] (bcm2835_handle_irq) from [<c01019f0>] (__irq_svc+0x70/0x98) The problem is in the console rebinding in fbcon_fb_unbind(). It uses the virtual console index as the new framebuffer index to bind the console(s) to. The correct way is to use the con2fb_map lookup table to find the framebuffer index. Fixes: cfafca80 ("fbdev: fbcon: console unregistration from unregister_framebuffer") Signed-off-by:
Noralf Trønnes <noralf@tronnes.org> Reviewed-by:
Mikulas Patocka <mpatocka@redhat.com> Acked-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
-
Peter Rosin authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit f75df8d4 ] Blitting an image with "negative" offsets is not working since there is no clipping. It hopefully just crashes. For the bootup logo, there is protection so that blitting does not happen as the image is drawn further and further to the right (ROTATE_UR) or further and further down (ROTATE_CW). There is however no protection when drawing in the opposite directions (ROTATE_UD and ROTATE_CCW). Add back this protection. The regression is 20-odd years old but the mindless warning-killing mentality displayed in commit 34bdb666 ("fbdev: fbmem: remove positive test on unsigned values") is also to blame, methinks. Fixes: 448d4797 ("fbdev: fb_do_show_logo() updates") Signed-off-by:
Peter Rosin <peda@axentia.se> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Fabian Frederick <ffrederick@users.sourceforge.net> Cc: Geert Uytterhoeven <geert+renesas@glider.be> cc: Geoff Levand <geoff@infradead.org> Cc: James Simmons <jsimmons@users.sf.net> Signed-off-by:
-
Alexey Khoroshilov authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit fdac7513 ] clps711x_fb_probe() increments refcnt of disp device node by of_parse_phandle() and leaves it undecremented on both successful and error paths. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: Alexander Shiyan <shc_work@mail.ru> Signed-off-by:
-
Nathan Chancellor authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit a52c5a16 ] There are several warnings from Clang about no case statement matching the constant 0: In file included from drivers/block/drbd/drbd_receiver.c:48: In file included from drivers/block/drbd/drbd_int.h:48: In file included from ./include/linux/drbd_genl_api.h:54: In file included from ./include/linux/genl_magic_struct.h:236: ./include/linux/drbd_genl.h:321:1: warning: no case matching constant switch condition '0' GENL_struct(DRBD_NLA_HELPER, 24, drbd_helper_info, ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ./include/linux/genl_magic_struct.h:220:10: note: expanded from macro 'GENL_struct' switch (0) { ^ Silence this warning by adding a 'case 0:' statement. Additionally, adjust the alignment of the statements in the ct_assert_unique macro to avoid a checkpatch warning. This solution was originally sent by Arnd Bergmann with a default case statement: https://lore.kernel.org/patchwork/patch/756723/ Link: https://github.com/ClangBuiltLinux/linux/issues/43Suggested-by:
Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by:
-
Lars Ellenberg authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 9848b6dd ] If you try to promote a Secondary while connected to a Primary and allow-two-primaries is NOT set, we will wait for "ping-timeout" to give this node a chance to detect a dead primary, in case the cluster manager noticed faster than we did. But if we then are *still* connected to a Primary, we fail (after an additional timeout of ping-timout). This change skips the spurious second timeout. Most people won't notice really, since "ping-timeout" by default is half a second. But in some installations, ping-timeout may be 10 or 20 seconds or more, and spuriously delaying the error return becomes annoying. Signed-off-by:
-
Lars Ellenberg authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit b17b5960 ] With "on-no-data-accessible suspend-io", DRBD requires the next attach or connect to be to the very same data generation uuid tag it lost last. If we first lost connection to the peer, then later lost connection to our own disk, we would usually refuse to re-connect to the peer, because it presents the wrong data set. However, if the peer first connects without a disk, and then attached its disk, we accepted that same wrong data set, which would be "unexpected" by any user of that DRBD and cause "undefined results" (read: very likely data corruption). The fix is to forcefully disconnect as soon as we notice that the peer attached to the "wrong" dataset. Signed-off-by:
-
Roland Kammerer authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit d29e89e3 ] So far there was the possibility that we called genlmsg_new(GFP_NOIO)/mutex_lock() while holding an rcu_read_lock(). This included cases like: drbd_sync_handshake (acquire the RCU lock) drbd_asb_recover_1p drbd_khelper drbd_bcast_event genlmsg_new(GFP_NOIO) --> may sleep drbd_sync_handshake (acquire the RCU lock) drbd_asb_recover_1p drbd_khelper notify_helper genlmsg_new(GFP_NOIO) --> may sleep drbd_sync_handshake (acquire the RCU lock) drbd_asb_recover_1p drbd_khelper notify_helper mutex_lock --> may sleep While using GFP_ATOMIC whould have been possible in the first two cases, the real fix is to narrow the rcu_read_lock. Reported-by:
Jia-Ju Bai <baijiaju1990@163.com> Reviewed-by:
Roland Kammerer <roland.kammerer@linbit.com> Signed-off-by:
-
Jia-Ju Bai authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 4f68ef64 ] The function cw1200_bss_info_changed() and cw1200_hw_scan() can be concurrently executed. The two functions both access a possible shared variable "frame.skb". This shared variable is freed by dev_kfree_skb() in cw1200_upload_beacon(), which is called by cw1200_bss_info_changed(). The free operation is protected by a mutex lock "priv->conf_mutex" in cw1200_bss_info_changed(). In cw1200_hw_scan(), this shared variable is accessed without the protection of the mutex lock "priv->conf_mutex". Thus, concurrency use-after-free bugs may occur. To fix these bugs, the original calls to mutex_lock(&priv->conf_mutex) and mutex_unlock(&priv->conf_mutex) are moved to the places, which can protect the accesses to the shared variable. Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Johan Hedberg authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 1629db9c ] In case a command which completes in Command Status was sent using the hci_cmd_send-family of APIs there would be a misleading error in the hci_get_cmd_complete function, since the code would be trying to fetch the Command Complete parameters when there are none. Avoid the misleading error and silently bail out from the function in case the received event is a command status. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Acked-by:
Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
YueHaibing authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit fa89a459 ] gcc warn this: net/ipv6/xfrm6_tunnel.c:143 __xfrm6_tunnel_alloc_spi() warn: always true condition '(spi <= 4294967295) => (0-u32max <= u32max)' 'spi' is u32, which always not greater than XFRM6_TUNNEL_SPI_MAX because of wrap around. So the second forloop will never reach. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Johannes Berg authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit efc38dd7 ] Due to the alignment handling, it actually matters where in the code we add the 4 bytes for the presence bitmap to the length; the first field is the timestamp with 8 byte alignment so we need to add the space for the extra vendor namespace presence bitmap *before* we do any alignment for the fields. Move the presence bitmap length accounting to the right place to fix the alignment for the data properly. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
-
Christophe Leroy authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 05a4ab82 ] With the following piece of code, the following compilation warning is encountered: if (_IOC_DIR(ioc) != _IOC_NONE) { int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ; if (!access_ok(verify, ioarg, _IOC_SIZE(ioc))) { drivers/platform/test/dev.c: In function 'my_ioctl': drivers/platform/test/dev.c:219:7: warning: unused variable 'verify' [-Wunused-variable] int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ; This patch fixes it by referencing 'type' in the macro allthough doing nothing with it. Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
-
Mark Rutland authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 0d640732 ] When we emulate an MMIO instruction, we advance the CPU state within decode_hsr(), before emulating the instruction effects. Having this logic in decode_hsr() is opaque, and advancing the state before emulation is problematic. It gets in the way of applying consistent single-step logic, and it prevents us from being able to fail an MMIO instruction with a synchronous exception. Clean this up by only advancing the CPU state *after* the effects of the instruction are emulated. Cc: Peter Maydell <peter.maydell@linaro.org> Reviewed-by:
Alex Bennée <alex.bennee@linaro.org> Reviewed-by:
Christoffer Dall <christoffer.dall@arm.com> Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
-
Beomho Seo authored
BugLink: https://bugs.launchpad.net/bugs/1818813 [ Upstream commit 31e93364 ] Commit 391f93f2 ("serial: core: Rework hw-assited flow control support") has changed the way the autoCTS mode is handled. According to that change, serial drivers which enable H/W autoCTS mode must set UPSTAT_AUTOCTS to prevent the serial core from inadvertently disabling TX. This patch adds proper handling of UPSTAT_AUTOCTS flag. Signed-off-by:
Beomho Seo <beomho.seo@samsung.com> [mszyprow: rephrased commit message] Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
