Currently when we do a packet flood to the Ethernet port, the console
reports error every time when a packet is dropped.  This is too
redundant and cost performance.  Remove message for this type of event.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch adds support for limiting the number of tx pause frames to a
default of 8. Previously, hardware would send out continuous stream of
pause frames.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch adds jumbo frame support for MCP79 chipsets.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch adds support for new tx statistic counters in the hardware -
unicast, multicast, and broadcast
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch enforces a stricter policy on rx errors. The driver needs to
verify whether there are multiple rx errors versus a single error.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Merge branch 'via-velocity' of git://git.kernel.org/pub/scm/linux/kernel/git/romieu/netdev-2.6 into tmp

Fix the problems reported for 2.6.27-rc1 caused by over aggressive
power management. Turning clock off on PCI Express is problematic for WOL,
and when doing multi-booting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

igb_init_managability does not actually perform any function as the two
registers it attempts to write are both read only on the host.  This patch
removes the function and all references to it from the driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Three functions were left in the code that are no longer used.  I am removing
these functions just to keep the code clean.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The igb_mta_set function was not being correctly used
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch changes the PCS configuration for serdes so that the flow
control options change be set via the ethtool -A option.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

With a fiber or serdes NIC installed the driver was causing a null pointer
dereference on driver unload.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The internal name was used in comments, replaced with silicon part number.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The L1 hardware contains a bug that flags a fragmented IP packet
as having an incorrect TCP/UDP checksum, even though the packet
is perfectly valid and its checksum is correct.  There's no way to
distinguish between one of these good packets and a packet that
actually contains a TCP/UDP checksum error, so all we can do is
allow the packet to be handed up to the higher layers and let it
be sorted out there.

Add a comment describing this condition and remove the code that
currently fails to handle what may or may not be a checksum error.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

There are currently no devices supported by the e1000e driver which need
ioport resources, remove the test for it and all unnecessary code
associated with it (struct e1000_adapter elements, local variables, etc.)
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

a few people seem to have problems maintaining gigabit link
and it was root caused to an interaction between the managability
firmware on the host and the driver, not communicating.

The form of communication they use is the drv_load bit.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

82573 EEPROMs have been shipped out with known issues. While most
people will never see the issues some people do and we know
how to address them. Warn the user if we find one of these
EEPROM issues.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The ndev_* printk's are too lenghty and we don't need to specify
the adapter/netdev struct at all, making this a lot more readable.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Set 64bits consistent DMA mask since it improves performance
in some cases. No need to check the return value since it is
not required for the driver to work.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Update myri10ge firmware headers.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This re-introduces commit 2b142900,
which was reverted due to the regression it caused by commit
fca082c9.

That regression was not root-caused by the original commit, it was just
uncovered by it, and the real fix was done by Alan Stern in commit
580da348 ("Fix USB storage hang on
command abort").

We can thus re-introduce the change that was confirmed by Alan Jenkins
to be still required by his odd card reader.

Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (78 commits)
  AX.25: Fix sysctl registration if !CONFIG_AX25_DAMA_SLAVE
  pktgen: mac count
  pktgen: random flow 
  bridge: Eliminate unnecessary forward delay
  bridge: fix compile warning in net/bridge/br_netfilter.c
  ipv4: remove unused field in struct flowi (include/net/flow.h).
  tg3: Fix 'scheduling while atomic' errors
  net: Kill plain NET_XMIT_BYPASS.
  net_sched: Add qdisc __NET_XMIT_BYPASS flag
  net_sched: Add qdisc __NET_XMIT_STOLEN flag
  iwl3945: fix merge mistake for packet injection
  iwlwifi: grap nic access before accessing periphery registers
  iwlwifi: decrement rx skb counter in scan abort handler
  iwlwifi: fix unhandled interrupt when HW rfkill is on
  iwlwifi: implement iwl5000_calc_rssi
  iwlwifi: memory allocation optimization
  iwlwifi: HW bug fixes
  p54: Fix potential concurrent access to private data
  rt2x00: Disable link tuning in rt2500usb
  iwlwifi: Don't use buffer allocated on the stack for led names
  ...

Since 49ffcf8f ("sysctl: update
sysctl_check_table") setting struct ctl_table.procname = NULL does no
longer work as it used to the way the AX.25 code is expecting it to
resulting in the AX.25 sysctl registration code to break if
CONFIG_AX25_DAMA_SLAVE was not set as in some distribution kernels.
Kernel releases from 2.6.24 are affected.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

dst_mac_count and src_mac_count patch from Eneas Hunguana
We have sent one mac address to much.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Random flow generation has not worked. This fixes it.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Stephen Hemminger <shemminger@vyatta.com>

Based upon original patch by Herbert Xu, which contained
the following problem description:

--------------------
When the forward delay is set to zero, we still delay the setting
of the forwarding state by one or possibly two timers depending
on whether STP is enabled.  This could either turn out to be
instantaneous, or horribly slow depending on the load of the
machine.

As there is nothing preventing us from enabling forwarding straight
away, this patch eliminates this potential delay by executing the
code directly if the forward delay is zero.

The effect of this problem is that immediately after the carrier
comes on a port, the bridge will drop all packets received from
that port until it enters forwarding mode, thus causing unnecessary
packet loss.

Note that this patch doesn't fully remove the delay due to the
link watcher.  We should also check the carrier state when we
are about to drop an incoming packet because the port is disabled.
But that's for another patch.
--------------------

This version of the fix takes a different approach, in that
it just does the state change directly.
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix (fatal error) s390 docbook file to handle renamed header files.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mips allmodconfig:

  drivers/media/video/vino.c: In function `vino_free_buffer_with_count':
  drivers/media/video/vino.c:811: warning: passing arg 1 of `virt_to_phys' makes pointer from integer without a cast
  drivers/media/video/vino.c: In function `vino_allocate_buffer':
  drivers/media/video/vino.c:889: warning: passing arg 1 of `virt_to_phys' makes pointer from integer without a cast
  drivers/media/video/vino.c: In function `vino_ioctl':
  drivers/media/video/vino.c:4364: error: implicit declaration of function `video_usercopy'

The patch fixes the error, but not the warnings.

Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gcc 4.3.0 correctly emits the following warnings.
When a vma covering addr is found, find_vma_prepare indeed returns without
setting pprev, rb_link, and rb_parent.

  mm/mmap.c: In function `insert_vm_struct':
  mm/mmap.c:2085: warning: `rb_parent' may be used uninitialized in this function
  mm/mmap.c:2085: warning: `rb_link' may be used uninitialized in this function
  mm/mmap.c:2084: warning: `prev' may be used uninitialized in this function
  mm/mmap.c: In function `copy_vma':
  mm/mmap.c:2124: warning: `rb_parent' may be used uninitialized in this function
  mm/mmap.c:2124: warning: `rb_link' may be used uninitialized in this function
  mm/mmap.c:2123: warning: `prev' may be used uninitialized in this function
  mm/mmap.c: In function `do_brk':
  mm/mmap.c:1951: warning: `rb_parent' may be used uninitialized in this function
  mm/mmap.c:1951: warning: `rb_link' may be used uninitialized in this function
  mm/mmap.c:1949: warning: `prev' may be used uninitialized in this function
  mm/mmap.c: In function `mmap_region':
  mm/mmap.c:1092: warning: `rb_parent' may be used uninitialized in this function
  mm/mmap.c:1092: warning: `rb_link' may be used uninitialized in this function
  mm/mmap.c:1089: warning: `prev' may be used uninitialized in this function

Hugh adds: in fact, none of find_vma_prepare's callers use those values
when a vma is found to be already covering addr, it's either an error or
an occasion to munmap and repeat.  Okay, let's quieten the compiler (but I
would prefer it if pprev, rb_link and rb_parent were meaningful in that
case, rather than whatever's in them from descending the tree).
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: "Ryan Hope" <rmh3093@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A documentation cleanup patch.  With a minor tweak to clarify units for
kbs.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: mark gross <mgross@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc: fix warnings

 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 3 has type 'u64'
 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 4 has type 'u64'
 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 5 has type 'u64'
 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 6 has type 'u64'
 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 7 has type 'u64'
 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 8 has type 'u64'
 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 9 has type 'u64'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Removed duplicated include <linux/delay.h> in
drivers/misc/sgi-gru/grutlbpurge.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/omfs/inode.c:495: warning: format '%llx' expects type 'long long
	unsigned int', but argument 2 has type 'u64'
fs/omfs/inode.c:495: warning: format '%llx' expects type 'long
	long unsigned int', but argument 3 has type '__be64'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix handling of nested structs or unions.  The regex to strip (eliminate)
nested structs or unions was limited to only 0 or 1 matches.  This can
cause an uneven number of left/right braces to be stripped, which causes
this:

Warning(linux-2.6.27-rc1-git2//include/net/mac80211.h:336): No description found for parameter '}'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

get_order() takes byte-sized input, not a page-granular one.

Irrespective of this fix I'm inclined to believe that this doesn't work
right anyway - bitmap_allocate_region() has an implicit assumption of
'pos' being suitable for 'order', which this function doesn't seem to
enforce (and since it's being called with a byte-granular value there's no
reason to believe that the callers would make sure device_addr is passed
accordingly - it's also not documented that way).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/aty/atyfb_base.c:2663: warning: 'aty_resume_chip' defined
but not used
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Antonino A. Daplas <adaplas@pol.net>
Cc: Mark Asselstine <asselsm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

of_node_put is needed before discarding a value received from
of_find_node_by_type, eg in error handling code.

The semantic patch that makes the change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct device_node *n;
struct device_node *n1;
struct device_node *n2;
statement S;
identifier f1,f2;
expression E1,E2;
constant C;
@@

n = of_find_node_by_type(...)
...
if (!n) S
... when != of_node_put(n)
    when != n1 = f1(n,...)
    when != E1 = n
    when any
    when strict
(
+ of_node_put(n);
  return -C;
|
  of_node_put(n);
|
  n2 = f2(n,...)
|
  E2 = n
|
  return ...;
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Timur Tabi <timur@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The name of the i2c buses shows in the output of "i2cdetect -l", so
it's important to give informative names.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If the 'clear' command is used on the frame buffer with a logo the upper
area is filled by few lines but not scrolled anymore.

Fix this by removing the protected area for the logo if any part of the
logo is cleared.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>