TI's AM654x PCIe EP has a restriction that BAR_0 is mapped to
application registers. "PCIe Inbound Address Translation" section in
AM65x Sitara Processors TRM (SPRUID7 – April 2018) describes BAR0 as
reserved.

Configure pci_endpoint_test to use BAR_2 instead.

Also set alignment to 64K since "PCIe Subsystem Address Translation"
section in TRM indicates minimum ATU window size is 64K.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Certain platforms like K2G reguires the outbound ATU window to be
aligned. The alignment size is already present in mem->page_size.
Use the alignment size present in mem->page_size to configure an
aligned ATU window. In order to raise an interrupt, CPU has to write
to address offset from the start of the window unlike before where
writes were always to the beginning of the ATU window.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Configure the Resizable BAR capability to advertise the smallest size
(1MB) for a couple of reasons:

- Host side resource allocation of BAR fails for larger sizes
- Endpoint function driver does not allocate memory for all supported
  sizes in the Resizable BAR capability.

If and when there is a usecase required to add more flexibility using
the Resizable BAR capability, this can be revisited.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Add PCIe EP support for AM654x Platforms in pci-keystone.c

Link: https://lore.kernel.org/linux-pci/20190325093947.32633-15-kishon@ti.com/Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: made dev_vdbg() call a comment]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Add devicetree binding documentation for PCIe in EP mode present in
AM654 SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>

Certain platforms like TI's AM654 do not have aseparate address space for
dbi2 instead they are accessed using the same address space as dbi
with some configuration bit set. In order to support such platforms,
add callbacks for accessing dbi2 address space.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

commit beb4641a ("PCI: dwc: Add MSI-X callbacks handler") while
adding MSI-X callback handler, introduced dw_pcie_ep_find_capability()
and __dw_pcie_ep_find_next_cap() for finding the MSI and MSIX capability.

However if MSI or MSIX capability is the last capability (i.e there are
no additional items in the capabilities list and the Next Capability
Pointer is set to '0'), __dw_pcie_ep_find_next_cap will return '0'
even though MSI or MSIX capability may be present because of
incorrect ordering of the "next_cap_ptr" check. Fix it.

Fixes: beb4641a ("PCI: dwc: Add MSI-X callbacks handler")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Add const qualifier to struct dw_pcie_ep_ops member of
struct dw_pcie_ep.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

The address that is allocated using pci_epf_alloc_space() is
directly written to the target address of the Inbound Address
Translation unit (ie the HW component implementing inbound address
decoding) on endpoint controllers.

Designware IP [1] has a configuration parameter (CX_ATU_MIN_REGION_SIZE
[2]) which has 64KB as default value and the lower 16 bits of the Base,
Limit and Target registers of the Inbound ATU are fixed to zero. If the
programmed memory address is not aligned to 64 KB boundary this causes
memory corruption.

Modify pci_epf_alloc_space() API to take alignment size as argument in
order to allocate buffers to be mapped to BARs with an alignment that
suits the platform where they are used.

Add an 'align' parameter to epc_features which can be used by platform
drivers to specify the BAR allocation alignment requirements and use
this while invoking pci_epf_alloc_space().

[1] "I/O and MEM Match Modes" section in DesignWare Cores PCI Express
     Controller Databook version 4.90a
[2]  http://www.ti.com/lit/ug/spruid7c/spruid7c.pdfSigned-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

PCIe in TI's AM654 devices is by default configured to work in GEN3 mode.

However PCIe does not work reliably in GEN3 mode because of SERDES
configuration.

Add support to set the link speed to GEN1, GEN2 or GEN3 based on
"max-link-speed" DT property with GEN2 as the default speed if
"max-link-speed" is absent.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

of_pci_get_max_link_speed() is built only if CONFIG_PCI is enabled.
Make of_pci_get_max_link_speed() to be also used by PCI Endpoint
controllers with just CONFIG_PCI_ENDPOINT enabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>

SERDES connected to the PCIe controller in AM654 requires
power on reset enable (POR_EN) to be set in the SERDES. The
SERDES driver sets POR_EN in the reset ops and it has to be
invoked before init or enable ops. In order for SERDES driver
to set POR_EN, invoke the phy_reset() API in pci-keystone driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Add PCIe RC support for AM654x Platforms in pci-keystone.c
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Add devicetree binding documentation for PCIe in RC mode present in
AM654 SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>

hook_fault_code() is an ARM32 specific API for hooking into data abort.

AM65X platforms (that integrate ARM v8 cores and select CONFIG_ARM64 as
arch) rely on pci-keystone.c but on them the enumeration of a
non-present BDF does not trigger a bus error, so the fixup exception
provided by calling hook_fault_code() is not needed and can be guarded
with CONFIG_ARM.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Synopsys designware version >= 4.80 uses a separate register space
for programming ATU. The current code identifies if there exists a
separate register space by accessing the register address of ATUs
in designware version < 4.80. Accessing this address results in
abort in the case of K2G.

Fix it here by adding "version" member to struct dw_pcie. This should be
set by platform specific drivers and designware core will use it to
identify if the platform has a separate ATU space. For platforms which
have not populated the version member, the old method of identification
will still be used.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

iatu_unroll_enabled flag is set only for Designware in host mode.

However iATU unroll can be applicable for endpoint mode too. Set
iatu_unroll_enabled flag in dw_pcie_setup() which is common for
both host mode and endpoint mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Document "atu" reg-names required to get the register space for ATU in
Synopsys designware core version >= 4.80.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Explicitly set the PCIe mode to BOOTCFG_DEVCFG instead of always
relying on the default values. This is required when EP mode has to
be explicitly written to BOOTCFG_DEVCFG register.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Add "ti,syscon-pcie-mode" dt-binding to hold phandle to the syscon
register that should be used to configure PCIe in RC mode or EP mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>

Move platform_get_resource() calls for resources that are applicable to
both host and endpoint mode (ie "dbics" and "app") from
ks_add_pcie_port() to the probe() callback, in preparation for adding
endpoint support to pci-keystone driver.

No functional change intended.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Use platform_get_resource_byname() instead of platform_get_resource()
which uses an index to get memory resources. While at that get the memory
resource defined specifically for configuration space instead of
deriving the configuration space address from dbics address space.

Since the pci-keystone driver has never worked in the mainline kernel,
DT backward compatibility is not an issue.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

No functional change. Instead of having two functions
ks_pcie_add_pcie_port() and ks_pcie_dw_host_init() for initializing
host, have a single function to perform all the host initialization.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Add "reg-names" binding information in order for device tree node
to be populated with the correct register strings.

This will break old DT compatibility. However Keystone PCI has never
worked in upstream kernel due to lack of SERDES support, so, before
SERDES support is added, cleanup the Keystone PCI dt-bindings.

This new binding will also be used by PCI in AM654 platform.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>

pci-keystone driver uses irq_of_parse_and_map() to get irq number of
error_irq.

Use platform_get_irq() instead and move platform_get_irq() and
request_irq() of error_irq from ks_pcie_add_pcie_port to ks_pcie_probe
since error_irq is common to both RC mode and EP mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Add start_link()/stop_link() dw_pcie_ops and invoke ks_pcie_start_link()
directly from host_init. start_link()/stop_link() ops are required for
adding EP mode support.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Platforms which populate msi_host_init() have their own MSI controller
logic. Writing to MSI control registers on platforms which do not use
Designware's MSI controller logic might have side effects.

To be safe, do not write to MSI control registers if the platform uses
its own MSI controller logic instead of Designware's MSI one.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Now that Keystone started using its own msi_irq_chip, remove
Keystone specific callback functions defined in dw_pcie_host_ops.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Use Keystone specific msi_irq_chip to configure the MSI controller
logic in the PCIe keystone wrapper instead of using the default
Designware msi_irq chip (dw_pci_msi_bottom_irq_chip) with
callback functions for configuring the Keystone MSI controller.
This will help to remove Keystone specific callback functions
added in dw_pcie_host_ops.

Move the default msi_irq_chip assignment to dw_pcie_host_init since
platforms that doesn't use the default msi_irq_chip will assign
msi_irq_chip in the msi_host_init() callback.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Platforms using DesignWare IP use dw_pci_msi_bottom_irq_chip for
configuring the MSI controller logic within the DesignWare IP. However
certain platforms like Keystone (K2G) which uses DesignWare IP have
their own MSI controller logic. For handling such platforms,
the irqchip ops use msi_irq_ack(), msi_set_irq(), msi_clear_irq()
callback functions.

Add support to use different msi_irq_chip with default set to
dw_pci_msi_bottom_irq_chip. This is in preparation to get rid of
msi_irq_ack(), msi_set_irq(), msi_clear_irq() and other Keystone
specific dw_pcie_host_ops.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

ks_pcie_msi_irq_handler() invokes ks_pcie_handle_msi_irq() for handling
the interrupts.

Having two functions for handling the interrupt was used when keystone
PCIe driver was implemented using two files but with commit b492aca3
("PCI: keystone: Merge pci-keystone-dw.c and pci-keystone.c"), which
merged the keystone PCIe driver to use a single file, two functions for
handling the interrupt handler are not required.

Handle MSI interrupt in a single interrupt handler here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

ks_pcie_msi_irq_handler() uses 'virq' to get the IRQ number offset.
This offset is used to get the correct MSI_IRQ_STATUS register
corresponding to the IRQ line that raised the interrupt.

There is no guarantee that 'virq' assigned for consecutive hardware
IRQ will be contiguous and this might get us an incorrect IRQ number
offset.

Fix it here by using 'hwirq' to get the IRQ number offset. Since we
don't store the 'virq' numbers of all the IRQ numbers, stop checking
if irq count is greater than MAX_MSI_HOST_IRQS and remove
MAX_MSI_HOST_IRQS.

Link: https://lkml.kernel.org/r/bb081d21-7c03-0357-4294-7e92d95d838c@arm.comSigned-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

ks_pcie_get_irq_controller_info() is used to configure both MSI and
legacy interrupt. This will prevent MSI or legacy interrupt specific
intializations. Add separate functions to configure MSI and legacy
interrupts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

No functional change. Change both MSI interrupt and legacy interrupt
related macros to take an additional argument in order to return the
correct register offset.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Pull more Kbuild updates from Masahiro Yamada:

 - add more Build-Depends to Debian source package

 - prefix header search paths with $(srctree)/

 - make modpost show verbose section mismatch warnings

 - avoid hard-coded CROSS_COMPILE for h8300

 - fix regression for Debian make-kpkg command

 - add semantic patch to detect missing put_device()

 - fix some warnings of 'make deb-pkg'

 - optimize NOSTDINC_FLAGS evaluation

 - add warnings about redundant generic-y

 - clean up Makefiles and scripts

* tag 'kbuild-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: remove stale lxdialog/.gitignore
  kbuild: force all architectures except um to include mandatory-y
  kbuild: warn redundant generic-y
  Revert "modsign: Abort modules_install when signing fails"
  kbuild: Make NOSTDINC_FLAGS a simply expanded variable
  kbuild: deb-pkg: avoid implicit effects
  coccinelle: semantic code search for missing put_device()
  kbuild: pkg: grep include/config/auto.conf instead of $KCONFIG_CONFIG
  kbuild: deb-pkg: introduce is_enabled and if_enabled_echo to builddeb
  kbuild: deb-pkg: add CONFIG_ prefix to kernel config options
  kbuild: add workaround for Debian make-kpkg
  kbuild: source include/config/auto.conf instead of ${KCONFIG_CONFIG}
  unicore32: simplify linker script generation for decompressor
  h8300: use cc-cross-prefix instead of hardcoding h8300-unknown-linux-
  kbuild: move archive command to scripts/Makefile.lib
  modpost: always show verbose warning for section mismatch
  ia64: prefix header search path with $(srctree)/
  libfdt: prefix header search paths with $(srctree)/
  deb-pkg: generate correct build dependencies

Pull x86 asm updates from Thomas Gleixner:
 "Two cleanup patches removing dead conditionals and unused code"

* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm: Remove unused __constant_c_x_memset() macro and inlines
  x86/asm: Remove dead __GNUC__ conditionals

Pull perf fixes from Thomas Gleixner:
 "Three fixes for the fallout from the TSX errata workaround:

   - Prevent memory corruption caused by a unchecked out of bound array
     index.

   - Two trivial fixes to address compiler warnings"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Make dev_attr_allow_tsx_force_abort static
  perf/x86: Fixup typo in stub functions
  perf/x86/intel: Fix memory corruption

Pull xen fix from Juergen Gross:
 "A fix for a Xen bug introduced by David's series for excluding
  ballooned pages in vmcores"

* tag 'for-linus-5.1b-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: Fix mapping PG_offline pages to user space

Pull 9p updates from Dominique Martinet:
 "Here is a 9p update for 5.1; there honestly hasn't been much.

  Two fixes (leak on invalid mount argument and possible deadlock on
  i_size update on 32bit smp) and a fall-through warning cleanup"

* tag '9p-for-5.1' of git://github.com/martinetd/linux:
  9p/net: fix memory leak in p9_client_create
  9p: use inode->i_lock to protect i_size_write() under 32-bit
  9p: mark expected switch fall-through