The "host" USB port on rk3288 has a hardware errata where we've got to
assert a PHY reset whenever we see a remote wakeup.  Add that quirk
property to the device tree.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Let's hook up the resets to the three USB PHYs on rk3288 as per the
bindings.  This is in preparation for a future patch that will set the
"snps,reset-phy-on-wake" on the host port.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

On the rk3288 USB host-only port (the one that's not the OTG-enabled
port) the PHY can get into a bad state when a wakeup is asserted (not
just a wakeup from full system suspend but also a wakeup from
autosuspend).

We can get the PHY out of its bad state by asserting its "port reset",
but unfortunately that seems to assert a reset onto the USB bus so it
could confuse things if we don't actually deenumerate / reenumerate the
device.

We can also get the PHY out of its bad state by fully resetting it using
the reset from the CRU (clock reset unit), which does a more full
reset.  The CRU-based reset appears to actually cause devices on the bus
to be removed and reinserted, which fixes the problem (albeit in a hacky
way).

It's unfortunate that we need to do a full re-enumeration of devices at
wakeup time, but this is better than alternative of letting the bus get
wedged.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

On Rockchip rk3288 there's a hardware quirk where we need to assert
the reset signal to the PHY when we get a remote wakeup on one of the
two ports.  Document this quirk in the bindings.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Various boards have an external VBUS supply regulator. This regulator
depends on the current mode of the controller which is defined as:
- dr_mode set to either "host" or "peripheral" (fixed value)
- dr_mode set to "otg", based on the OTG status the dwc2 controller
  internally switches between "host" and "peripheral" mode (selection
  happens at runtime)

Based on the current mode the regulator has to be enabled or disabled:
- host: provide power to the connected USB device, thus the regulator
  has to be enabled
- peripheral: the host device to which the controller is connected
  provides power, thus the regulator has to be disabled

Add the dt-bindings documentation for this property so .dts authors know
that this property exists and how it behaves.

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external vbus supply")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The net2280 UDC driver (and also net2272, probably via copy-and-paste)
incorrectly checks the req->zero flag during OUT transfers, after
copying data from the UDC's FIFO into memory.  This makes no sense at
all; the "zero" flag indicates that an extra zero-length packet should
be appended to an IN transfer if the length is an even multiple of the
maxpacket size.  It has nothing to do with OUT transfers.

In practice this doesn't cause any problems because gadget drivers
never set req->zero for OUT transfers anyway.  Still, it is an error
and unnecessary code, so this patch removes the check.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The net2280 driver includes an unnecessary test for an endpoint's
queue being empty.  The test is redundant; it sits inside a
conditional block of an "if" statement which already tests the
endpoint's queue.

This patch removes the redundant test.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The dependency to ensure this driver links correctly fails since
it can not be a loadable module:

drivers/usb/phy/phy-fsl-usb.o: In function `fsl_otg_set_peripheral':
phy-fsl-usb.c:(.text+0x2224): undefined reference to `usb_gadget_vbus_disconnect'

Make the option 'tristate' so it can work correctly.

Fixes: 5a8d651a ("usb: gadget: move gadget API functions to udc-core")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

To be able to use the default USB class drivers available in Microsoft
Windows, we need to add OS descriptors to the exported USB gadget to
tell the OS that we are compatible with the built-in drivers.

Copy the OS descriptor support from f_rndis into f_ncm. As a result,
using the WINNCM compatible ID, the UsbNcm driver is loaded on
enumeration without the need for a custom driver or inf file.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When connecting a CDC-NCM gadget to an host that uses the NTP-32 mode,
or that relies on the default CRC setting, the current implementation gets
confused, and does not expect the correct signature for its packets.

Fix this, by ensuring that the ndp_sign member in the f_ncm structure
always contain a valid value.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When the driver tries to get optional clock, it ignores all errors,
but if only ignores -ENOENT, it will cover some real errors, such as
-EPROBE_DEFER, so use devm_clk_get_optional() to get optional clock.

Cc: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Avoiding switch to L1 state in any stage of control transfers.
Send NYET handshake to LPM token.

Renamed GLPMCFG_LPM_ACCEPT_CTRL_ISOC to GLPMCFG_LPM_REJECT_CTRL_CONTROL
because by setting this bit core reject LPM token.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In (e583d9db USB: global suspend and remote wakeup don't mix) we
introduced wakeup_enabled_descendants() as a static function.  We'd
like to use this function in USB controller drivers to know if we
should keep the controller on during suspend time, since doing so has
a power impact.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This is an attempt to rehash commit 0cf884e8 ("usb: dwc2: add bus
suspend/resume for dwc2") on ToT.  That commit was reverted in commit
b0bb9bb6 ("Revert "usb: dwc2: add bus suspend/resume for dwc2"")
because apparently it broke the Altera SOCFPGA.

With all the changes that have happened to dwc2 in the meantime, it's
possible that the Altera SOCFPGA will just magically work with this
change now.  ...and it would be good to get bus suspend/resume
implemented.

This change is a forward port of one that's been living in the Chrome
OS 3.14 kernel tree.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Adds support for Amlogic G12A USB Control Glue HW.

The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only

A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually
via a debugfs interface. The IRQ mode change detect is yet to be added
in a future patchset, mainly due to lack of hardware to validate on.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patchs sets the params for the DWC2 Controller found in the
Amlogic G12A SoC family.

It mainly sets the settings reported incorrect by the driver,
leaving the remaining detected automatically by the driver and
provided by the DT node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Adds the bindings for the Amlogic G12A USB Glue HW.

The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only

A glue connects these both controllers to 2 USB2 PHYs,
and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller.

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.

The PHYs phandles are passed  to the Glue node since the Glue controls the
interface with the PHY, not the DWC3 controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Adds the specific compatible string for the DWC2 IP found in the
Amlogic G12A SoC Family.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The syzkaller USB fuzzer identified a failure mode in which dummy-hcd
would never give back an unlinked URB.  This causes usb_kill_urb() to
hang, leading to WARNINGs and unkillable threads.

In dummy-hcd, all URBs are given back by the dummy_timer() routine as
it scans through the list of pending URBS.  Failure to give back URBs
can be caused by failure to start or early exit from the scanning
loop.  The code currently has two such pathways: One is triggered when
an unsupported bus transfer speed is encountered, and the other by
exhausting the simulated bandwidth for USB transfers during a frame.

This patch removes those two paths, thereby allowing all unlinked URBs
to be given back in a timely manner.  It adds a check for the bus
speed when the gadget first starts running, so that dummy_timer() will
never thereafter encounter an unsupported speed.  And it prevents the
loop from exiting as soon as the total bandwidth has been used up (the
scanning loop continues, giving back unlinked URBs as they are found,
but not transferring any more data).

Thanks to Andrey Konovalov for manually running the syzkaller fuzzer
to help track down the source of the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+d919b0f29d7b5a4994b9@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Keep EXTCON support optional, as some platforms do not need it.

Do the same for USB_DWC3_OMAP while we're at it.

Fixes: 3def4031 ("usb: dwc3: add EXTCON dependency for qcom")
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The following kernel panic happens due to the io_data buffer gets deallocated
before the async io is completed. Add a check for the case where io_data buffer
should be deallocated by ffs_user_copy_worker.

[   41.663334] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
[   41.672099] #PF error: [normal kernel read fault]
[   41.677356] PGD 20c974067 P4D 20c974067 PUD 20c973067 PMD 0
[   41.683687] Oops: 0000 [#1] PREEMPT SMP
[   41.687976] CPU: 1 PID: 7 Comm: kworker/u8:0 Tainted: G     U            5.0.0-quilt-2e5dc0ac-00790-gd8c79f2-dirty #2
[   41.705309] Workqueue: adb ffs_user_copy_worker
[   41.705316] RIP: 0010:__vunmap+0x2a/0xc0
[   41.705318] Code: 0f 1f 44 00 00 48 85 ff 0f 84 87 00 00 00 55 f7 c7 ff 0f 00 00 48 89 e5 41 55 41 89 f5 41 54 53 48 89 fb 75 71 e8 56 d7 ff ff <4c> 8b 60 48 4d 85 e4 74 76 48 89 df e8 25 ff ff ff 45 85 ed 74 46
[   41.705320] RSP: 0018:ffffbc3a40053df0 EFLAGS: 00010286
[   41.705322] RAX: 0000000000000000 RBX: ffffbc3a406f1000 RCX: 0000000000000000
[   41.705323] RDX: 0000000000000001 RSI: 0000000000000001 RDI: 00000000ffffffff
[   41.705324] RBP: ffffbc3a40053e08 R08: 000000000001fb79 R09: 0000000000000037
[   41.705325] R10: ffffbc3a40053b68 R11: ffffbc3a40053cad R12: fffffffffffffff2
[   41.705326] R13: 0000000000000001 R14: 0000000000000000 R15: ffffffffffffffff
[   41.705328] FS:  0000000000000000(0000) GS:ffff9e2977a80000(0000) knlGS:0000000000000000
[   41.705329] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   41.705330] CR2: 0000000000000048 CR3: 000000020c994000 CR4: 00000000003406e0
[   41.705331] Call Trace:
[   41.705338]  vfree+0x50/0xb0
[   41.705341]  ffs_user_copy_worker+0xe9/0x1c0
[   41.705344]  process_one_work+0x19f/0x3e0
[   41.705348]  worker_thread+0x3f/0x3b0
[   41.829766]  kthread+0x12b/0x150
[   41.833371]  ? process_one_work+0x3e0/0x3e0
[   41.838045]  ? kthread_create_worker_on_cpu+0x70/0x70
[   41.843695]  ret_from_fork+0x3a/0x50
[   41.847689] Modules linked in: hci_uart bluetooth ecdh_generic rfkill_gpio dwc3_pci dwc3 snd_usb_audio mei_me tpm_crb snd_usbmidi_lib xhci_pci xhci_hcd mei tpm snd_hwdep cfg80211 snd_soc_skl snd_soc_skl_ipc snd_soc_sst_ipc snd_soc_sst_dsp snd_hda_ext_core snd_hda_core videobuf2_dma_sg crlmodule
[   41.876880] CR2: 0000000000000048
[   41.880584] ---[ end trace 2bc4addff0f2e673 ]---
[   41.891346] RIP: 0010:__vunmap+0x2a/0xc0
[   41.895734] Code: 0f 1f 44 00 00 48 85 ff 0f 84 87 00 00 00 55 f7 c7 ff 0f 00 00 48 89 e5 41 55 41 89 f5 41 54 53 48 89 fb 75 71 e8 56 d7 ff ff <4c> 8b 60 48 4d 85 e4 74 76 48 89 df e8 25 ff ff ff 45 85 ed 74 46
[   41.916740] RSP: 0018:ffffbc3a40053df0 EFLAGS: 00010286
[   41.922583] RAX: 0000000000000000 RBX: ffffbc3a406f1000 RCX: 0000000000000000
[   41.930563] RDX: 0000000000000001 RSI: 0000000000000001 RDI: 00000000ffffffff
[   41.938540] RBP: ffffbc3a40053e08 R08: 000000000001fb79 R09: 0000000000000037
[   41.946520] R10: ffffbc3a40053b68 R11: ffffbc3a40053cad R12: fffffffffffffff2
[   41.954502] R13: 0000000000000001 R14: 0000000000000000 R15: ffffffffffffffff
[   41.962482] FS:  0000000000000000(0000) GS:ffff9e2977a80000(0000) knlGS:0000000000000000
[   41.971536] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   41.977960] CR2: 0000000000000048 CR3: 000000020c994000 CR4: 00000000003406e0
[   41.985930] Kernel panic - not syncing: Fatal exception
[   41.991817] Kernel Offset: 0x16000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
[   42.009525] Rebooting in 10 seconds..
[   52.014376] ACPI MEMORY or I/O RESET_REG.

Fixes: 772a7a72 ("usb: gadget: f_fs: Allow scatter-gather buffers")
Signed-off-by: Fei Yang <fei.yang@intel.com>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pull NFS client bugfix from Trond Myklebust:
 "Fix a regression in which an RPC call can be tagged with an error
  despite the transmission being successful"

* tag 'nfs-for-5.1-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: Ignore queue transmission errors on successful transmission

Pull SCSI fixes from James Bottomley:
 "Three minor fixes: two obvious ones in drivers and a fix to the SG_IO
  path to correctly return status on error"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: aic7xxx: fix EISA support
  Revert "scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO"
  scsi: core: set result when the command cannot be dispatched

Pull block fixes from Jens Axboe:
 "A set of small fixes that should go into this series. This contains:

   - Removal of unused queue member (Hou)

   - Overflow bvec fix (Ming)

   - Various little io_uring tweaks (me)
       - kthread parking
       - Only call cpu_possible() for verified CPU
       - Drop unused 'file' argument to io_file_put()
       - io_uring_enter vs io_uring_register deadlock fix
       - CQ overflow fix

   - BFQ internal depth update fix (me)"

* tag 'for-linus-20190420' of git://git.kernel.dk/linux-block:
  block: make sure that bvec length can't be overflow
  block: kill all_q_node in request_queue
  io_uring: fix CQ overflow condition
  io_uring: fix possible deadlock between io_uring_{enter,register}
  io_uring: drop io_file_put() 'file' argument
  bfq: update internal depth state when queue depth changes
  io_uring: only test SQPOLL cpu after we've verified it
  io_uring: park SQPOLL thread if it's percpu

Pill i3c fixes from Boris Brezillon:

 - fix the random PID check

 - fix the disable controller logic in the designware driver

 - fix I3C entry in MAINTAINERS

* tag 'i3c/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
  MAINTAINERS: Fix the I3C entry
  i3c: dw: Fix dw_i3c_master_disable controller by using correct mask
  i3c: Fix the verification of random PID

Pull sound fixes from Takashi Iwai:
 "Two core fixes for long-standing bugs for the races at concurrent
  device creation and deletion that were (unsurprisingly) spotted by
  syzkaller with usb-fuzzer.

  The rest are usual small HD-audio fixes"

* tag 'sound-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - add two more pin configuration sets to quirk table
  ALSA: core: Fix card races between register and disconnect
  ALSA: info: Fix racy addition/deletion of nodes
  ALSA: hda: Initialize power_state field properly

Pull timer fixes from Ingo Molnar:
 "Misc clocksource driver fixes, and a sched-clock wrapping fix"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timers/sched_clock: Prevent generic sched_clock wrap caused by tick_freeze()
  clocksource/drivers/timer-ti-dm: Remove omap_dm_timer_set_load_start
  clocksource/drivers/oxnas: Fix OX820 compatible
  clocksource/drivers/arm_arch_timer: Remove unneeded pr_fmt macro
  clocksource/drivers/npcm: select TIMER_OF

Pull perf fixes from Ingo Molnar:
 "Misc fixes:
   - various tooling fixes
   - kretprobe fixes
   - kprobes annotation fixes
   - kprobes error checking fix
   - fix the default events for AMD Family 17h CPUs
   - PEBS fix
   - AUX record fix
   - address filtering fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/kprobes: Avoid kretprobe recursion bug
  kprobes: Mark ftrace mcount handler functions nokprobe
  x86/kprobes: Verify stack frame on kretprobe
  perf/x86/amd: Add event map for AMD Family 17h
  perf bpf: Return NULL when RB tree lookup fails in perf_env__find_btf()
  perf tools: Fix map reference counting
  perf evlist: Fix side band thread draining
  perf tools: Check maps for bpf programs
  perf bpf: Return NULL when RB tree lookup fails in perf_env__find_bpf_prog_info()
  tools include uapi: Sync sound/asound.h copy
  perf top: Always sample time to satisfy needs of use of ordered queuing
  perf evsel: Use hweight64() instead of hweight_long(attr.sample_regs_user)
  tools lib traceevent: Fix missing equality check for strcmp
  perf stat: Disable DIR_FORMAT feature for 'perf stat record'
  perf scripts python: export-to-sqlite.py: Fix use of parent_id in calls_view
  perf header: Fix lock/unlock imbalances when processing BPF/BTF info
  perf/x86: Fix incorrect PEBS_REGS
  perf/ring_buffer: Fix AUX record suppression
  perf/core: Fix the address filtering fix
  kprobes: Fix error check when reusing optimized probes

Pull x86 fixes from Ingo Molnar:
 "Misc fixes all over the place: a console spam fix, section attributes
  fixes, a KASLR fix, a TLB stack-variable alignment fix, a reboot
  quirk, boot options related warnings fix, an LTO fix, a deadlock fix
  and an RDT fix"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu/intel: Lower the "ENERGY_PERF_BIAS: Set to normal" message's log priority
  x86/cpu/bugs: Use __initconst for 'const' init data
  x86/mm/KASLR: Fix the size of the direct mapping section
  x86/Kconfig: Fix spelling mistake "effectivness" -> "effectiveness"
  x86/mm/tlb: Revert "x86/mm: Align TLB invalidation info"
  x86/reboot, efi: Use EFI reboot for Acer TravelMate X514-51T
  x86/mm: Prevent bogus warnings with "noexec=off"
  x86/build/lto: Fix truncated .bss with -fdata-sections
  x86/speculation: Prevent deadlock on ssb_state::lock
  x86/resctrl: Do not repeat rdtgroup mode initialization

Pull scheduler fixes from Ingo Molnar:
 "A deadline scheduler warning/race fix, and a cfs_period_us quota
  calculation workaround where the real fix looks too involved to merge
  immediately"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/deadline: Correctly handle active 0-lag timers
  sched/fair: Limit sched_cfs_period_timer() loop to avoid hard lockup

Pull locking fixes from Ingo Molnar:
 "A lockdep warning fix and a script execution fix when atomics are
  generated"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/atomics: Don't assume that scripts are executable
  locking/lockdep: Make lockdep_unregister_key() honor 'debug_locks' again

Pull cgroup fix from Tejun Heo:
 "A patch to fix a RCU imbalance error in the devices cgroup
  configuration error path"

* 'for-5.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  device_cgroup: fix RCU imbalance in error case

Pull percpu fixlet from Dennis Zhou:
 "This stops printing the base address of percpu memory on
  initialization"

* 'for-5.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu:
  percpu: stop printing kernel addresses

Pull tty/serial fixes from Greg KH:
 "Here are five small fixes for some tty/serial/vt issues that have been
  reported.

  The vt one has been around for a while, it is good to finally get that
  resolved. The others fix a build warning that showed up in 5.1-rc1,
  and resolve a problem in the sh-sci driver.

  Note, the second patch for build warning fix for the sc16is7xx driver
  was just applied to the tree, as it resolves a problem with the
  previous patch to try to solve the issue. It has not shown up in
  linux-next yet, unlike all of the other patches, but it has passed
  0-day testing and everyone seems to agree that it is correct"

* tag 'tty-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  sc16is7xx: put err_spi and err_i2c into correct #ifdef
  vt: fix cursor when clearing the screen
  sc16is7xx: move label 'err_spi' to correct section
  serial: sh-sci: Fix HSCIF RX sampling point adjustment
  serial: sh-sci: Fix HSCIF RX sampling point calculation

Merge misc fixes from Andrew Morton:
 "16 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
  mm/kmemleak.c: fix unused-function warning
  init: initialize jump labels before command line option parsing
  kernel/watchdog_hld.c: hard lockup message should end with a newline
  kcov: improve CONFIG_ARCH_HAS_KCOV help text
  mm: fix inactive list balancing between NUMA nodes and cgroups
  mm/hotplug: treat CMA pages as unmovable
  proc: fixup proc-pid-vm test
  proc: fix map_files test on F29
  mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
  mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
  mm: swapoff: shmem_unuse() stop eviction without igrab()
  mm: swapoff: take notice of completion sooner
  mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
  mm: swapoff: shmem_find_swap_entries() filter out other types
  slab: store tagged freelist for off-slab slabmgmt

Pull staging and IIO fixes from Greg KH:
 "Here is a bunch of IIO driver fixes, and some smaller staging driver
  fixes, for 5.1-rc6. The IIO fixes were delayed due to my vacation, but
  all resolve a number of reported issues and have been in linux-next
  for a few weeks with no reported issues.

  The other staging driver fixes are all tiny, resolving some reported
  issues in the comedi and most drivers, as well as some erofs fixes.

  All of these patches have been in linux-next with no reported issues"

* tag 'staging-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (24 commits)
  staging: comedi: ni_usb6501: Fix possible double-free of ->usb_rx_buf
  staging: comedi: ni_usb6501: Fix use of uninitialized mutex
  staging: erofs: fix unexpected out-of-bound data access
  staging: comedi: vmk80xx: Fix possible double-free of ->usb_rx_buf
  staging: comedi: vmk80xx: Fix use of uninitialized semaphore
  staging: most: core: use device description as name
  iio: core: fix a possible circular locking dependency
  iio: ad_sigma_delta: select channel when reading register
  iio: pms7003: select IIO_TRIGGERED_BUFFER
  iio: cros_ec: Fix the maths for gyro scale calculation
  iio: adc: xilinx: prevent touching unclocked h/w on remove
  iio: adc: xilinx: fix potential use-after-free on probe
  iio: adc: xilinx: fix potential use-after-free on remove
  iio: dac: mcp4725: add missing powerdown bits in store eeprom
  io: accel: kxcjk1013: restore the range after resume.
  iio:chemical:bme680: Fix SPI read interface
  iio:chemical:bme680: Fix, report temperature in millidegrees
  iio: chemical: fix missing Kconfig block for sgp30
  iio: adc: at91: disable adc channel interrupt in timeout case
  iio: gyro: mpu3050: fix chip ID reading
  ...

Pull char/misc fixes from Greg KH:
 "Here are four small misc driver fixes for 5.1-rc6.

  Nothing major at all, they fix up a Kconfig issues, a SPDX invalid
  license tag, and two tiny bugfixes.

  All have been in linux-next for a while with no reported issues"

* tag 'char-misc-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  drivers: power: supply: goldfish_battery: Fix bogus SPDX identifier
  extcon: ptn5150: fix COMPILE_TEST dependencies
  misc: fastrpc: add checked value for dma_set_mask
  habanalabs: remove low credit limit of DMA #0

bvec->bv_offset may be bigger than PAGE_SIZE sometimes, such as,
when one bio is splitted in the middle of one bvec via bio_split(),
and bi_iter.bi_bvec_done is used to build offset of the 1st bvec of
remained bio. And the remained bio's bvec may be re-submitted to fs
layer via ITER_IBVEC, such as loop and nvme-loop.

So we have to make sure that every bvec's offset is less than
PAGE_SIZE from bio_for_each_segment_all() because some drivers(loop,
nvme-loop) passes the splitted bvec to fs layer via ITER_BVEC.

This patch fixes this issue reported by Zhang Yi When running nvme/011.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Yi Zhang <yi.zhang@redhat.com>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixes: 6dc4f100 ("block: allow bio_for_each_segment_all() to iterate over multi-page bvec")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

all_q_node has not been used since commit 4b855ad3 ("blk-mq: Create
hctx for each present CPU"), so remove it.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>