- 28 Mar, 2019 1 commit
-
-
Heiner Kallweit authored
This patches fixes few issues in mv88e6390x_port_set_cmode(). 1. When entering the function the old cmode may be 0, in this case mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail out and have no chance to set a new mode. Therefore deal properly with -ENODEV. 2. Once we have disabled power and irq, let's set the cached cmode to 0. This reflects the actual status and is cleaner if we bail out with an error in the following function calls. 3. The cached cmode is used by mv88e6390x_serdes_get_lane(), mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable(). Currently we set the cached mode to the new one at the very end of the function only, means until then we use the old one what may be wrong. 4. When calling mv88e6390_serdes_irq_enable() we use the lane value belonging to the old cmode. Get the lane belonging to the new cmode before calling this function. It's hard to provide a good "Fixes" tag because quite a few smaller changes have been done to the code in question recently. Fixes: d235c48b ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 27 Mar, 2019 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: "Fixes here and there, a couple new device IDs, as usual: 1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei. 2) Fix 64-bit division in iwlwifi, from Arnd Bergmann. 3) Fix documentation for some eBPF helpers, from Quentin Monnet. 4) Some UAPI bpf header sync with tools, also from Quentin Monnet. 5) Set descriptor ownership bit at the right time for jumbo frames in stmmac driver, from Aaro Koskinen. 6) Set IFF_UP properly in tun driver, from Eric Dumazet. 7) Fix load/store doubleword instruction generation in powerpc eBPF JIT, from Naveen N. Rao. 8) nla_nest_start() return value checks all over, from Kangjie Lu. 9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this merge window. From Marcelo Ricardo Leitner and Xin Long. 10) Fix memory corruption with large MTUs in stmmac, from Aaro Koskinen. 11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric Dumazet. 12) Fix topology subscription cancellation in tipc, from Erik Hugne. 13) Memory leak in genetlink error path, from Yue Haibing. 14) Valid control actions properly in packet scheduler, from Davide Caratti. 15) Even if we get EEXIST, we still need to rehash if a shrink was delayed. From Herbert Xu. 16) Fix interrupt mask handling in interrupt handler of r8169, from Heiner Kallweit. 17) Fix leak in ehea driver, from Wen Yang" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits) dpaa2-eth: fix race condition with bql frame accounting chelsio: use BUG() instead of BUG_ON(1) net: devlink: skip info_get op call if it is not defined in dumpit net: phy: bcm54xx: Encode link speed and activity into LEDs tipc: change to check tipc_own_id to return in tipc_net_stop net: usb: aqc111: Extend HWID table by QNAP device net: sched: Kconfig: update reference link for PIE net: dsa: qca8k: extend slave-bus implementations net: dsa: qca8k: remove leftover phy accessors dt-bindings: net: dsa: qca8k: support internal mdio-bus dt-bindings: net: dsa: qca8k: fix example net: phy: don't clear BMCR in genphy_soft_reset bpf, libbpf: clarify bump in libbpf version info bpf, libbpf: fix version info and add it to shared object rxrpc: avoid clang -Wuninitialized warning tipc: tipc clang warning net: sched: fix cleanup NULL pointer exception in act_mirr r8169: fix cable re-plugging issue net: ethernet: ti: fix possible object reference leak net: ibm: fix possible object reference leak ...
-
- 26 Mar, 2019 20 commits
-
-
git://git.linux-nfs.org/projects/trondmy/linux-nfsLinus Torvalds authored
Pull NFS client bugfixes from Trond Myklebust: "Highlights include: Stable fixes: - Fix nfs4_lock_state refcounting in nfs4_alloc_{lock,unlock}data() - fix mount/umount race in nlmclnt. - NFSv4.1 don't free interrupted slot on open Bugfixes: - Don't let RPC_SOFTCONN tasks time out if the transport is connected - Fix a typo in nfs_init_timeout_values() - Fix layoutstats handling during read failovers - fix uninitialized variable warning" * tag 'nfs-for-5.1-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: SUNRPC: fix uninitialized variable warning pNFS/flexfiles: Fix layoutstats handling during read failovers NFS: Fix a typo in nfs_init_timeout_values() SUNRPC: Don't let RPC_SOFTCONN tasks time out if the transport is connected NFSv4.1 don't free interrupted slot on open NFS: fix mount/umount race in nlmclnt. NFS: Fix nfs4_lock_state refcounting in nfs4_alloc_{lock,unlock}data()
-
Alakesh Haloi authored
Avoid following compiler warning on uninitialized variable net/sunrpc/xprtsock.c: In function ‘xs_read_stream_request.constprop’: net/sunrpc/xprtsock.c:525:10: warning: ‘read’ may be used uninitialized in this function [-Wmaybe-uninitialized] return read; ^~~~ net/sunrpc/xprtsock.c:529:23: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized] return ret < 0 ? ret : read; ~~~~~~~~~~~~~~^~~~~~ Signed-off-by: Alakesh Haloi <alakesh.haloi@gmail.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
-
Ioana Ciornei authored
It might happen that Tx conf acknowledges a frame before it was subscribed in bql, as subscribing was previously done after the enqueue operation. This patch moves the netdev_tx_sent_queue call before the actual frame enqueue, so that this can never happen. Fixes: 569dac6a ("dpaa2-eth: bql support") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Arnd Bergmann authored
clang warns about possible bugs in a dead code branch after BUG_ON(1) when CONFIG_PROFILE_ALL_BRANCHES is enabled: drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: error: variable 'buf_size' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized] BUG_ON(1); ^~~~~~~~~ include/asm-generic/bug.h:61:36: note: expanded from macro 'BUG_ON' #define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0) ^~~~~~~~~~~~~~~~~~~ include/linux/compiler.h:48:23: note: expanded from macro 'unlikely' # define unlikely(x) (__branch_check__(x, 0, __builtin_constant_p(x))) ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/chelsio/cxgb4/sge.c:482:9: note: uninitialized use occurs here return buf_size; ^~~~~~~~ drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: note: remove the 'if' if its condition is always true BUG_ON(1); ^ include/asm-generic/bug.h:61:32: note: expanded from macro 'BUG_ON' #define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0) ^ drivers/net/ethernet/chelsio/cxgb4/sge.c:459:14: note: initialize the variable 'buf_size' to silence this warning int buf_size; ^ = 0 Use BUG() here to create simpler code that clang understands correctly. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
In dumpit, unlike doit, the check for info_get op being defined is missing. Add it and avoid null pointer dereference in case driver does not define this op. Fixes: f9cf2288 ("devlink: add device information API") Reported-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
Previously the green and amber LEDs on this quad PHY were solid, to indicate an encoding of the link speed (10/100/1000). This keeps the LEDs always on just as before, but now they flash on Rx/Tx activity. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Xin Long authored
When running a syz script, a panic occurred: [ 156.088228] BUG: KASAN: use-after-free in tipc_disc_timeout+0x9c9/0xb20 [tipc] [ 156.094315] Call Trace: [ 156.094844] <IRQ> [ 156.095306] dump_stack+0x7c/0xc0 [ 156.097346] print_address_description+0x65/0x22e [ 156.100445] kasan_report.cold.3+0x37/0x7a [ 156.102402] tipc_disc_timeout+0x9c9/0xb20 [tipc] [ 156.106517] call_timer_fn+0x19a/0x610 [ 156.112749] run_timer_softirq+0xb51/0x1090 It was caused by the netns freed without deleting the discoverer timer, while later on the netns would be accessed in the timer handler. The timer should have been deleted by tipc_net_stop() when cleaning up a netns. However, tipc has been able to enable a bearer and start d->timer without the local node_addr set since Commit 52dfae5c ("tipc: obtain node identity from interface by default"), which caused the timer not to be deleted in tipc_net_stop() then. So fix it in tipc_net_stop() by changing to check local node_id instead of local node_addr, as Jon suggested. While at it, remove the calling of tipc_nametbl_withdraw() there, since tipc_nametbl_stop() will take of the nametbl's freeing after. Fixes: 52dfae5c ("tipc: obtain node identity from interface by default") Reported-by: syzbot+a25307ad099309f1c2b9@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dmitry Bezrukov authored
New device of QNAP based on aqc111u Add this ID to blacklist of cdc_ether driver as well Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Leslie Monis authored
RFC 8033 replaces the IETF draft for PIE Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Lamparter authored
This patch implements accessors for the QCA8337 MDIO access through the MDIO_MASTER register, which makes it possible to access the PHYs on slave-bus through the switch. In cases where the switch ports are already mapped via external "phy-phandles", the internal mdio-bus is disabled in order to prevent a duplicated discovery and enumeration of the same PHYs. Don't use mixed external and internal mdio-bus configurations, as this is not supported by the hardware. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Lamparter authored
This belated patch implements Andrew Lunn's request of "remove the phy_read() and phy_write() functions." <https://lore.kernel.org/patchwork/comment/902734/> While seemingly harmless, this causes the switch's user port PHYs to get registered twice. This is because the DSA subsystem will create a slave mdio-bus not knowing that the qca8k_phy_(read|write) accessors operate on the external mdio-bus. So the same "bus" gets effectively duplicated. Cc: stable@vger.kernel.org Fixes: 6b93fb46 ("net-next: dsa: add new driver for qca8xxx family") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Lamparter authored
This patch updates the qca8k's binding to document to the approach for using the internal mdio-bus of the supported qca8k switches. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Lamparter authored
In the example, the phy at phy@0 is clashing with the switch0@0 at the same address. Usually, the switches are accessible through pseudo PHYs which in case of the qca8k are located at 0x10 - 0x18. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linuxLinus Torvalds authored
Pull btrfs fixes from David Sterba: - fsync fixes: i_size for truncate vs fsync, dio vs buffered during snapshotting, remove complicated but incomplete assertion - removed excessive warnigs, misreported device stats updates - fix raid56 page mapping for 32bit arch - fixes reported by static analyzer * tag 'for-5.1-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: Btrfs: fix assertion failure on fsync with NO_HOLES enabled btrfs: Avoid possible qgroup_rsv_size overflow in btrfs_calculate_inode_block_rsv_size btrfs: Fix bound checking in qgroup_trace_new_subtree_blocks btrfs: raid56: properly unmap parity page in finish_parity_scrub() btrfs: don't report readahead errors and don't update statistics Btrfs: fix file corruption after snapshotting due to mix of buffered/DIO writes btrfs: remove WARN_ON in log_dir_items Btrfs: fix incorrect file size after shrinking truncate and fsync
-
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-traceLinus Torvalds authored
Pull tracing fixes from Steven Rostedt: "Three small fixes: - A fix to a double free in the histogram code - Uninitialized variable fix - Use NULL instead of zero fix and spelling fixes" * tag 'trace-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: ftrace: Fix warning using plain integer as NULL & spelling corrections tracing: initialize variable in create_dyn_event() tracing: Remove unnecessary var_ref destroy in track_data_destroy()
-
git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linuxLinus Torvalds authored
Pull file locking bugfix from Jeff Layton: "Just a single fix for a bug that crept into POSIX lock deadlock detection in v5.0" * tag 'locks-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux: locks: wake any locks blocked on request before deadlock check
-
Hariprasad Kelam authored
Changed 0 --> NULL to avoid sparse warning Corrected spelling mistakes reported by checkpatch.pl Sparse warning below: sudo make C=2 CF=-D__CHECK_ENDIAN__ M=kernel/trace CHECK kernel/trace/ftrace.c kernel/trace/ftrace.c:3007:24: warning: Using plain integer as NULL pointer kernel/trace/ftrace.c:4758:37: warning: Using plain integer as NULL pointer Link: http://lkml.kernel.org/r/20190323183523.GA2244@hari-Inspiron-1545Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
-
Frank Rowand authored
Fix compile warning in create_dyn_event(): 'ret' may be used uninitialized in this function [-Wuninitialized]. Link: http://lkml.kernel.org/r/1553237900-8555-1-git-send-email-frowand.list@gmail.com Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Tom Zanussi <tom.zanussi@linux.intel.com> Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Cc: stable@vger.kernel.org Fixes: 5448d44c ("tracing: Add unified dynamic event framework") Signed-off-by: Frank Rowand <frank.rowand@sony.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
-
Tom Zanussi authored
Commit 656fe2ba (tracing: Use hist trigger's var_ref array to destroy var_refs) centralized the destruction of all the var_refs in one place so that other code didn't have to do it. The track_data_destroy() added later ignored that and also destroyed the track_data var_ref, causing a double-free error flagged by KASAN. ================================================================== BUG: KASAN: use-after-free in destroy_hist_field+0x30/0x70 Read of size 8 at addr ffff888086df2210 by task bash/1694 CPU: 6 PID: 1694 Comm: bash Not tainted 5.1.0-rc1-test+ #15 Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v03.03 07/14/2016 Call Trace: dump_stack+0x71/0xa0 ? destroy_hist_field+0x30/0x70 print_address_description.cold.3+0x9/0x1fb ? destroy_hist_field+0x30/0x70 ? destroy_hist_field+0x30/0x70 kasan_report.cold.4+0x1a/0x33 ? __kasan_slab_free+0x100/0x150 ? destroy_hist_field+0x30/0x70 destroy_hist_field+0x30/0x70 track_data_destroy+0x55/0xe0 destroy_hist_data+0x1f0/0x350 hist_unreg_all+0x203/0x220 event_trigger_open+0xbb/0x130 do_dentry_open+0x296/0x700 ? stacktrace_count_trigger+0x30/0x30 ? generic_permission+0x56/0x200 ? __x64_sys_fchdir+0xd0/0xd0 ? inode_permission+0x55/0x200 ? security_inode_permission+0x18/0x60 path_openat+0x633/0x22b0 ? path_lookupat.isra.50+0x420/0x420 ? __kasan_kmalloc.constprop.12+0xc1/0xd0 ? kmem_cache_alloc+0xe5/0x260 ? getname_flags+0x6c/0x2a0 ? do_sys_open+0x149/0x2b0 ? do_syscall_64+0x73/0x1b0 ? entry_SYSCALL_64_after_hwframe+0x44/0xa9 ? _raw_write_lock_bh+0xe0/0xe0 ? __kernel_text_address+0xe/0x30 ? unwind_get_return_address+0x2f/0x50 ? __list_add_valid+0x2d/0x70 ? deactivate_slab.isra.62+0x1f4/0x5a0 ? getname_flags+0x6c/0x2a0 ? set_track+0x76/0x120 do_filp_open+0x11a/0x1a0 ? may_open_dev+0x50/0x50 ? _raw_spin_lock+0x7a/0xd0 ? _raw_write_lock_bh+0xe0/0xe0 ? __alloc_fd+0x10f/0x200 do_sys_open+0x1db/0x2b0 ? filp_open+0x50/0x50 do_syscall_64+0x73/0x1b0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7fa7b24a4ca2 Code: 25 00 00 41 00 3d 00 00 41 00 74 4c 48 8d 05 85 7a 0d 00 8b 00 85 c0 75 6d 89 f2 b8 01 01 00 00 48 89 fe bf 9c ff ff ff 0f 05 <48> 3d 00 f0 ff ff 0f 87 a2 00 00 00 48 8b 4c 24 28 64 48 33 0c 25 RSP: 002b:00007fffbafb3af0 EFLAGS: 00000246 ORIG_RAX: 0000000000000101 RAX: ffffffffffffffda RBX: 000055d3648ade30 RCX: 00007fa7b24a4ca2 RDX: 0000000000000241 RSI: 000055d364a55240 RDI: 00000000ffffff9c RBP: 00007fffbafb3bf0 R08: 0000000000000020 R09: 0000000000000002 R10: 00000000000001b6 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000003 R14: 0000000000000001 R15: 000055d364a55240 ================================================================== So remove the track_data_destroy() destroy_hist_field() call for that var_ref. Link: http://lkml.kernel.org/r/1deffec420f6a16d11dd8647318d34a66d1989a9.camel@linux.intel.com Fixes: 466f4528 ("tracing: Generalize hist trigger onmax and save action") Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
-
Heiner Kallweit authored
So far we effectively clear the BMCR register. Some PHY's can deal with this (e.g. because they reset BMCR to a default as part of a soft-reset) whilst on others this causes issues because e.g. the autoneg bit is cleared. Marvell is an example, see also thread [0]. So let's be a little bit more gentle and leave all bits we're not interested in as-is. This change is needed for PHY drivers to properly deal with the original patch. [0] https://marc.info/?t=155264050700001&r=1&w=2 Fixes: 6e2d85ec ("net: phy: Stop with excessive soft reset") Tested-by: Phil Reid <preid@electromag.com.au> Tested-by: liweihang <liweihang@hisilicon.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 25 Mar, 2019 6 commits
-
-
Linus Torvalds authored
This reverts commit 1aec4211. Steven Rostedt reports that it causes a hang at bootup and bisected it to this commit. The troigger is apparently a module alias for "parport_lowlevel" that points to "parport_pc", which causes a hang with modprobe -q -- parport_lowlevel blocking forever with a backtrace like this: wait_for_completion_killable+0x1c/0x28 call_usermodehelper_exec+0xa7/0x108 __request_module+0x351/0x3d8 get_lowlevel_driver+0x28/0x41 [parport] __parport_register_driver+0x39/0x1f4 [parport] daisy_drv_init+0x31/0x4f [parport] parport_bus_init+0x5d/0x7b [parport] parport_default_proc_register+0x26/0x1000 [parport] do_one_initcall+0xc2/0x1e0 do_init_module+0x50/0x1d4 load_module+0x1c2e/0x21b3 sys_init_module+0xef/0x117 Supid says: "Due to the new device model daisy driver will now try to find the parallel ports while trying to register its driver so that it can bind with them. Now, since daisy driver is loaded while parport bus is initialising the list of parport is still empty and it tries to load the lowlevel driver, which has an alias set to parport_pc, now causes a deadlock" But I don't think the daisy driver should be loaded by the parport initialization in the first place, so let's revert the whole change. If the daisy driver can just initialize separately on its own (like a driver should), instead of hooking into the parport init sequence directly, this issue probably would go away. Reported-and-bisected-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Reported-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Jeff Layton authored
Andreas reported that he was seeing the tdbtorture test fail in some cases with -EDEADLCK when it wasn't before. Some debugging showed that deadlock detection was sometimes discovering the caller's lock request itself in a dependency chain. While we remove the request from the blocked_lock_hash prior to reattempting to acquire it, any locks that are blocked on that request will still be present in the hash and will still have their fl_blocker pointer set to the current request. This causes posix_locks_deadlock to find a deadlock dependency chain when it shouldn't, as a lock request cannot block itself. We are going to end up waking all of those blocked locks anyway when we go to reinsert the request back into the blocked_lock_hash, so just do it prior to checking for deadlocks. This ensures that any lock blocked on the current request will no longer be part of any blocked request chain. URL: https://bugzilla.kernel.org/show_bug.cgi?id=202975 Fixes: 5946c431 ("fs/locks: allow a lock request to block other requests.") Cc: stable@vger.kernel.org Reported-by: Andreas Schneider <asn@redhat.com> Signed-off-by: Neil Brown <neilb@suse.com> Signed-off-by: Jeff Layton <jlayton@kernel.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller authored
Alexei Starovoitov says: ==================== pull-request: bpf 2019-03-24 The following pull-request contains BPF updates for your *net* tree. The main changes are: 1) libbpf verision fix up from Daniel. 2) fix liveness propagation from Jakub. 3) fix verbose print of refcounted regs from Martin. 4) fix for large map allocations from Martynas. 5) fix use after free in sanitize_ptr_alu from Xu. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexei Starovoitov authored
Daniel Borkmann says: ==================== First one is fixing version in Makefile and shared object and second one clarifies bump in version. Thanks! v1 -> v2: - Fix up soname, thanks Stanislav! ==================== Signed-off-by: Alexei Starovoitov <ast@kernel.org>
-
Daniel Borkmann authored
The current documentation suggests that we would need to bump the libbpf version on every change. Lets clarify this a bit more and reflect what we do today in practice, that is, bumping it once per development cycle. Fixes: 76d1b894 ("libbpf: Document API and ABI conventions") Reported-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
-
Daniel Borkmann authored
Even though libbpf's versioning script for the linker (libbpf.map) is pointing to 0.0.2, the BPF_EXTRAVERSION in the Makefile has not been updated along with it and is therefore still on 0.0.1. While fixing up, I also noticed that the generated shared object versioning information is missing, typical convention is to have a linker name (libbpf.so), soname (libbpf.so.0) and real name (libbpf.so.0.0.2) for library management. This is based upon the LIBBPF_VERSION as well. The build will then produce the following bpf libraries: # ll libbpf* libbpf.a libbpf.so -> libbpf.so.0.0.2 libbpf.so.0 -> libbpf.so.0.0.2 libbpf.so.0.0.2 # readelf -d libbpf.so.0.0.2 | grep SONAME 0x000000000000000e (SONAME) Library soname: [libbpf.so.0] And install them accordingly: # rm -rf /tmp/bld; mkdir /tmp/bld; make -j$(nproc) O=/tmp/bld install Auto-detecting system features: ... libelf: [ on ] ... bpf: [ on ] CC /tmp/bld/libbpf.o CC /tmp/bld/bpf.o CC /tmp/bld/nlattr.o CC /tmp/bld/btf.o CC /tmp/bld/libbpf_errno.o CC /tmp/bld/str_error.o CC /tmp/bld/netlink.o CC /tmp/bld/bpf_prog_linfo.o CC /tmp/bld/libbpf_probes.o CC /tmp/bld/xsk.o LD /tmp/bld/libbpf-in.o LINK /tmp/bld/libbpf.a LINK /tmp/bld/libbpf.so.0.0.2 LINK /tmp/bld/test_libbpf INSTALL /tmp/bld/libbpf.a INSTALL /tmp/bld/libbpf.so.0.0.2 # ll /usr/local/lib64/libbpf.* /usr/local/lib64/libbpf.a /usr/local/lib64/libbpf.so -> libbpf.so.0.0.2 /usr/local/lib64/libbpf.so.0 -> libbpf.so.0.0.2 /usr/local/lib64/libbpf.so.0.0.2 Fixes: 1bf4b058 ("tools: bpftool: add probes for eBPF program types") Fixes: 1b76c13e ("bpf tools: Introduce 'bpf' library and add bpf feature check") Reported-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
-
- 24 Mar, 2019 12 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 fixes from Ted Ts'o: "Miscellaneous ext4 bug fixes for 5.1" * tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: prohibit fstrim in norecovery mode ext4: cleanup bh release code in ext4_ind_remove_space() ext4: brelse all indirect buffer in ext4_ind_remove_space() ext4: report real fs size after failed resize ext4: add missing brelse() in add_new_gdb_meta_bg() ext4: remove useless ext4_pin_inode() ext4: avoid panic during forced reboot ext4: fix data corruption caused by unaligned direct AIO ext4: fix NULL pointer dereference while journal is aborted
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull scheduler updates from Thomas Gleixner: "Third more careful attempt for this set of fixes: - Prevent a 32bit math overflow in the cpufreq code - Fix a buffer overflow when scanning the cgroup2 cpu.max property - A set of fixes for the NOHZ scheduler logic to prevent waking up CPUs even if the capacity of the busy CPUs is sufficient along with other tweaks optimizing the behaviour for asymmetric systems (big/little)" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/fair: Skip LLC NOHZ logic for asymmetric systems sched/fair: Tune down misfit NOHZ kicks sched/fair: Comment some nohz_balancer_kick() kick conditions sched/core: Fix buffer overflow in cgroup2 property cpu.max sched/cpufreq: Fix 32-bit math overflow
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf updates from Thomas Gleixner: "A larger set of perf updates. Not all of them are strictly fixes, but that's solely the tip maintainers fault as they let the timely -rc1 pull request fall through the cracks for various reasons including travel. So I'm sending this nevertheless because rebasing and distangling fixes and updates would be a mess and risky as well. As of tomorrow, a strict fixes separation is happening again. Sorry for the slip-up. Kernel: - Handle RECORD_MMAP vs. RECORD_MMAP2 correctly so different consumers of the mmap event get what they requested. Tools: - A larger set of updates to perf record/report/scripts vs. time stamp handling - More Python3 fixups - A pile of memory leak plumbing - perf BPF improvements and fixes - Finalize the perf.data directory storage" [ Note: the kernel part is strictly a fix, the updates are purely to tooling - Linus ] * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits) perf bpf: Show more BPF program info in print_bpf_prog_info() perf bpf: Extract logic to create program names from perf_event__synthesize_one_bpf_prog() perf tools: Save bpf_prog_info and BTF of new BPF programs perf evlist: Introduce side band thread perf annotate: Enable annotation of BPF programs perf build: Check what binutils's 'disassembler()' signature to use perf bpf: Process PERF_BPF_EVENT_PROG_LOAD for annotation perf symbols: Introduce DSO_BINARY_TYPE__BPF_PROG_INFO perf feature detection: Add -lopcodes to feature-libbfd perf top: Add option --no-bpf-event perf bpf: Save BTF information as headers to perf.data perf bpf: Save BTF in a rbtree in perf_env perf bpf: Save bpf_prog_info information as headers to perf.data perf bpf: Save bpf_prog_info in a rbtree in perf_env perf bpf: Make synthesize_bpf_events() receive perf_session pointer instead of perf_tool perf bpf: Synthesize bpf events with bpf_program__get_prog_info_linear() bpftool: use bpf_program__get_prog_info_linear() in prog.c:do_dump() tools lib bpf: Introduce bpf_program__get_prog_info_linear() perf record: Replace option --bpf-event with --no-bpf-event perf tests: Fix a memory leak in test__perf_evsel__tp_sched_test() ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "A set of x86 fixes: - Prevent potential NULL pointer dereferences in the HPET and HyperV code - Exclude the GART aperture from /proc/kcore to prevent kernel crashes on access - Use the correct macros for Cyrix I/O on Geode processors - Remove yet another kernel address printk leak - Announce microcode reload completion as requested by quite some people. Microcode loading has become popular recently. - Some 'Make Clang' happy fixlets - A few cleanups for recently added code" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/gart: Exclude GART aperture from kcore x86/hw_breakpoints: Make default case in hw_breakpoint_arch_parse() return an error x86/mm/pti: Make local symbols static x86/cpu/cyrix: Remove {get,set}Cx86_old macros used for Cyrix processors x86/cpu/cyrix: Use correct macros for Cyrix calls on Geode processors x86/microcode: Announce reload operation's completion x86/hyperv: Prevent potential NULL pointer dereference x86/hpet: Prevent potential NULL pointer dereference x86/lib: Fix indentation issue, remove extra tab x86/boot: Restrict header scope to make Clang happy x86/mm: Don't leak kernel addresses x86/cpufeature: Fix various quality problems in the <asm/cpu_device_hd.h> header
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fixes from Thomas Gleixner: "A set of small fixes plus the removal of stale board support code: - Remove the board support code from the clpx711x clocksource driver. This change had fallen through the cracks and I'm sending it now rather than dealing with people who want to improve that stale code for 3 month. - Use the proper clocksource mask on RICSV - Make local scope functions and variables static" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: clocksource/drivers/clps711x: Remove board support clocksource/drivers/riscv: Fix clocksource mask clocksource/drivers/mips-gic-timer: Make gic_compare_irqaction static clocksource/drivers/timer-ti-dm: Make omap_dm_timer_set_load_start() static clocksource/drivers/tcb_clksrc: Make tc_clksrc_suspend/resume() static clocksource/drivers/clps711x: Make clps711x_clksrc_init() static time/jiffies: Make refined_jiffies static
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull locking fixes from Thomas Gleixner: "Two small fixes: - Cure a recently introduces error path hickup which tries to unregister a not registered lockdep key in te workqueue code - Prevent unaligned cmpxchg() crashes in the robust list handling code by sanity checking the user space supplied futex pointer" * 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: futex: Ensure that futex address is aligned in handle_futex_death() workqueue: Only unregister a registered lockdep key
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fixes from Thomas Gleixner: "A set of fixes for the interrupt subsystem: - Remove secondary GIC support on systems w/o device-tree support - A set of small fixlets in various irqchip drivers - static and fall-through annotations - Kernel doc and typo fixes" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq: Mark expected switch case fall-through genirq/devres: Remove excess parameter from kernel doc irqchip/irq-mvebu-sei: Make mvebu_sei_ap806_caps static irqchip/mbigen: Don't clear eventid when freeing an MSI irqchip/stm32: Don't set rising configuration registers at init irqchip/stm32: Don't clear rising/falling config registers at init dt-bindings: irqchip: renesas-irqc: Document r8a774c0 support irqchip/mmp: Make mmp_irq_domain_ops static irqchip/brcmstb-l2: Make two init functions static genirq: Fix typo in comment of IRQD_MOVE_PCNTXT irqchip/gic-v3-its: Fix comparison logic in lpi_range_cmp irqchip/gic: Drop support for secondary GIC in non-DT systems irqchip/imx-irqsteer: Fix of_property_read_u32() error handling
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull core fixes from Thomas Gleixner: "Two small fixes: - Move the large objtool_file struct off the stack so objtool works in setups with a tight stack limit. - Make a few variables static in the watchdog core code" * 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: watchdog/core: Make variables static objtool: Move objtool_file struct off the stack
-
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linuxLinus Torvalds authored
Pull thermal management fixes from Zhang Rui: - Fix a wrong __percpu structure declaration in intel_powerclamp driver (Luc Van Oostenryck) - Fix truncated name of the idle injection kthreads created by intel_powerclamp driver (Zhang Rui) - Fix the missing UUID supports in int3400 thermal driver (Matthew Garrett) - Fix a crash when accessing the debugfs of bcm2835 SoC thermal driver (Phil Elwell) - A couple of trivial fixes/cleanups in some SoC thermal drivers * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: thermal/intel_powerclamp: fix truncated kthread name thermal: mtk: Allocate enough space for mtk_thermal. thermal/int340x_thermal: fix mode setting thermal/int340x_thermal: Add additional UUIDs thermal: cpu_cooling: Remove unused cur_freq variable thermal: bcm2835: Fix crash in bcm2835_thermal_debugfs thermal: samsung: Fix incorrect check after code merge thermal/intel_powerclamp: fix __percpu declaration of worker_data
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull smb3 fixes from Steve French: - two fixes for stable for guest mount problems with smb3.1.1 - two fixes for crediting (SMB3 flow control) on resent requests - a byte range lock leak fix - two fixes for incorrect rc mappings * tag '5.1-rc1-cifs-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6: cifs: update internal module version number SMB3: Fix SMB3.1.1 guest mounts to Samba cifs: Fix slab-out-of-bounds when tracing SMB tcon cifs: allow guest mounts to work for smb3.11 fix incorrect error code mapping for OBJECTID_NOT_FOUND cifs: fix that return -EINVAL when do dedupe operation CIFS: Fix an issue with re-sending rdata when transport returning -EAGAIN CIFS: Fix an issue with re-sending wdata when transport returning -EAGAIN
-
git://github.com/ojeda/linuxLinus Torvalds authored
Pull auxdisplay updates from Miguel Ojeda: "A few fixes and improvements for auxdisplay: - Series to fix a memory leak in hd44780 while introducing charlcd_free(). From Andy Shevchenko - Series to clean up the Kconfig menus and a couple of improvements for charlcd. From Mans Rullgard" * tag 'auxdisplay-for-linus-v5.1-rc2' of git://github.com/ojeda/linux: auxdisplay: charlcd: make backlight initial state configurable auxdisplay: charlcd: simplify init message display auxdisplay: deconfuse configuration auxdisplay: hd44780: Convert to use charlcd_free() auxdisplay: panel: Convert to use charlcd_free() auxdisplay: charlcd: Introduce charlcd_free() helper auxdisplay: charlcd: Move to_priv() to charlcd namespace auxdisplay: hd44780: Fix memory leak on ->remove()
-