- 06 Jun, 2017 40 commits
-
-
Niklas Söderlund authored
The pad lookup code can be broken out to increase readability and to reduce code duplication. Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Niklas Söderlund authored
It makes more sense to store the sink and source pads in struct rvin_graph_entity since that contains other subdevice related information. The data type to store pad information in is unsigned int and not int, change this. While we are at it drop the _idx suffix from the names, this never made sense. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Niklas Söderlund authored
The driver supports a single input only, which can be either analog or digital. If the subdevice supports dv_timings_cap the input is digital and the driver should not fill in the standard. Signed-off-by:
-
Niklas Söderlund authored
The rcar-vin driver only uses one pad, pad number 0. - All v4l2 operations that did not check that the requested operation was for pad 0 have been updated with a check to enforce this. - All v4l2 operations that stored (and later restored) the requested pad before substituting it for the subdevice pad number have been updated to not store the incoming pad and simply restore it to 0 after the subdevice operation is complete. Signed-off-by:
-
Niklas Söderlund authored
Use rvin_reset_format() in rvin_s_dv_timings() instead of just resetting a few fields. This fixes an issue where the field format was not properly set after S_DV_TIMINGS. Signed-off-by:
-
Niklas Söderlund authored
These two were forgotten when refactoring the format reset code. If they are not also reset at the same time as width and height the format returned from G_FMT will not match reality. Signed-off-by:
-
Sakari Ailus authored
All drivers have been converted from V4L2 OF to V4L2 fwnode. The V4L2 OF framework is now unused. Remove it. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Sakari Ailus authored
Instead of including the V4L2 OF header in ReST documentation, use the V4L2 fwnode header instead. Signed-off-by:
-
Sakari Ailus authored
Switch users of the v4l2_of_ APIs to the more generic v4l2_fwnode_ APIs. Async OF matching is replaced by fwnode matching and OF matching support is removed. Signed-off-by:
-
Sakari Ailus authored
Pass the more generic fwnode_handle to the init function than the device_node. Signed-off-by:
-
Sakari Ailus authored
Add fwnode matching to complement OF node matching. And fwnode may also be an OF node. Do not enable fwnode matching yet. It will replace OF matching soon. Signed-off-by:
-
Sakari Ailus authored
The fwnode_handle is a more generic way than OF device_node to describe firmware nodes. Instead of the OF API, use more generic fwnode API to obtain the same information. As the V4L2 fwnode support will be required by a small minority of e.g. ACPI based systems (the same might actually go for OF), make this a module instead of embedding it in the videodev module. The origins of the V4L2 fwnode framework is in the V4L2 OF framework. Signed-off-by:
-
Sean Young authored
The lirc_zilog driver is the last remaining lirc driver, so the existing todo is no longer relevant. Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Sean Young authored
Inlining these functions into the probe function makes it much more readable. Signed-off-by:
-
Sean Young authored
These functions are too short and removing them makes the code more readable. Signed-off-by:
-
Sean Young authored
Several error paths do not free up resources. This simplifies the code and fixes this. Signed-off-by:
-
Sean Young authored
If the probe fails (e.g. port already in use), rmmod causes null deref. Signed-off-by:
-
Ricardo Silva authored
Fix all checkpatch reported issues for: * CHECK: "braces {} should be used on all arms of this statement". * CHECK: "Unbalanced braces around else statement". Make sure all if/else statements are balanced in terms of braces. Most cases in code are, but a few were left unbalanced, so put them all consistent with the recommended style. Signed-off-by:Ricardo Silva <rjpdasilva@gmail.com> Signed-off-by:
-
Ricardo Silva authored
Fix all checkpatch reported issues for "CHECK: Prefer kzalloc(sizeof(*<p>)...) over kzalloc(sizeof(struct <P>)...)". Other similar case in the code already using recommended style, so make it all consistent with the recommended practice. Signed-off-by:
-
Ricardo Silva authored
Fix all checkpatch reported issues for "CHECK: Prefer using '"%s...", __func__' to using '<func_name>', ..." Use recommended style. Additionally, __func__ was already used in similar cases throughout the code, so make it all consistent. Signed-off-by:
-
Ricardo Silva authored
Fix all checkpatch reported issues for "CHECK: Comparison to NULL could be written...". Do these comparisons using the recommended coding style and consistent with other similar cases in the file, which already used the recommended way. Signed-off-by:
-
Ricardo Silva authored
Fix style issues reported by checkpatch, affecting whitespace only: * CHECK: "Please don't use multiple blank lines". Two of these still triggering and left untouched because used for separating logical blocks (vars from functions, etc.). * CHECK: "spaces preferred around that '<operator>'". All fixed. * CHECK: "Alignment should match open parenthesis". All fixed except one on line 1161, left untouched for readability. Move towards recommended coding style without compromising readability. Signed-off-by:
-
David Härdeman authored
The key_addr member is only assigned, never used. So, remove it. Signed-off-by:
David Härdeman <david@hardeman.nu> Signed-off-by:
-
David Härdeman authored
Just some debug statements to change. Signed-off-by:
-
David Härdeman authored
Changing the protocol does not imply that the keymap changes. Signed-off-by:
-
David Härdeman authored
The REP_DELAY setting on the input device is independent of hardware. This change should not change how to driver works (as it does a keydown/keyup and has no real repeat handling). Signed-off-by:
-
David Härdeman authored
Remove some stuff from lirc_dev.h which is not used anywhere. Signed-off-by:
-
David Härdeman authored
Remove superfluous includes and defines. Signed-off-by:
-
David Härdeman authored
Most drivers return both values when the device is gone. Signed-off-by:
-
David Härdeman authored
The "debug" parameter isn't actually used anywhere. Signed-off-by:
-
David Härdeman authored
device_add() and friends already manage the references to the parent device so these calls aren't necessary. Signed-off-by:
-
David Härdeman authored
These two functions only make the logic in lirc_register_driver() harder to follow. (Note that almost no other driver calls kobject_set_name() on their cdev so I simply removed that part). Signed-off-by:
-
David Härdeman authored
Always let the kernel decide what minor the lirc chardev gets. Signed-off-by:
-
David Härdeman authored
Merging the two means that lirc_allocate_buffer() is called before device_add() and cdev_add() which makes more sense. This also simplifies the locking slightly because lirc_allocate_buffer() will always be called with lirc_dev_lock held. Signed-off-by:
-
David Härdeman authored
Every caller of lirc_register_driver() passes their own fops and there are no users of lirc_dev_fop_write() in the kernel tree. Thus we can make fops mandatory and remove lirc_dev_fop_write(). Signed-off-by:
-
David Härdeman authored
out_sysfs is misleading, sysfs only comes into play after device_add(). Also, calling device_init() before the rest of struct dev is filled out is clearer. Signed-off-by:
-
David Härdeman authored
There are no drivers which use this functionality. Signed-off-by:
-
David Härdeman authored
Since there are no users of this functionality, it can be removed altogether. Signed-off-by:
-
David Härdeman authored
drv->set_use_inc and drv->set_use_dec are already optional so we can remove all dummy functions. Signed-off-by:
-
A Sun authored
Once IR blasting or mceusb device commands fail with mce_async_callback() TX -EPIPE error, all subsequent TX to device then fail with the same error. ... [ 249.986174] mceusb 1-1.2:1.0: requesting 38000 HZ carrier [ 249.986210] mceusb 1-1.2:1.0: send request called (size=0x4) [ 249.986256] mceusb 1-1.2:1.0: send request complete (res=0) [ 249.986403] mceusb 1-1.2:1.0: Error: request urb status = -32 (TX HALT) [ 249.999885] mceusb 1-1.2:1.0: send request called (size=0x3) [ 249.999929] mceusb 1-1.2:1.0: send request complete (res=0) [ 250.000013] mceusb 1-1.2:1.0: Error: request urb status = -32 (TX HALT) [ 250.019830] mceusb 1-1.2:1.0: send request called (size=0x21) [ 250.019868] mceusb 1-1.2:1.0: send request complete (res=0) [ 250.020007] mceusb 1-1.2:1.0: Error: request urb status = -32 (TX HALT) ... Fault simulation/injection is by executing the following USB operation in a mceusb instrumented driver, prior to TX I/O. retval = usb_control_msg(ir->usbdev, usb_sndctrlpipe(ir->usbdev, 0), USB_REQ_SET_FEATURE, USB_RECIP_ENDPOINT, USB_ENDPOINT_HALT, usb_pipeendpoint(ir->pipe_out), NULL, 0, USB_CTRL_SET_TIMEOUT); dev_dbg(ir->dev, "set halt retval, %d", retval); After setting halt state for the TX endpoint, perform an lirc "irsend" to generate TX traffic to device. After the TX HALT, the patch restores subsequent TX to working state. ... [ 508.009638] mceusb 1-1.2:1.0: send request called (size=0x3) [ 508.009697] mceusb 1-1.2:1.0: send request complete (res=0) [ 508.009847] mce_async_callback() [ 508.009864] mceusb 1-1.2:1.0: Error: request urb status = -32 (TX HALT) [ 508.009890] mceusb 1-1.2:1.0: kevent 0 scheduled [ 508.021552] mceusb 1-1.2:1.0: send request called (size=0x21) [ 508.021598] mceusb 1-1.2:1.0: send request complete (res=0) [ 508.021963] mce_async_callback() [ 508.021981] mceusb 1-1.2:1.0: tx data: 84 b0 0c 8c 0c 84 8c 0c 8c 0c 84 8c 0c 8c 0c 84 98 0c 98 0c 84 98 0c 8c 0c 84 8c 0c 8c 0c 81 8c 80 (length=33) [ 508.021997] mceusb 1-1.2:1.0: Raw IR data, 0 pulse/space samples [ 508.066627] mceusb 1-1.2:1.0: send request called (size=0x3) [ 508.066669] mceusb 1-1.2:1.0: send request complete (res=0) [ 508.066841] mce_async_callback() [ 508.066858] mceusb 1-1.2:1.0: tx data: 9f 08 03 (length=3) ... Signed-off-by:A Sun <as1033x@comcast.net> Signed-off-by:
-
