Add support for the HW feature of multi-packet WQE in XDP
xmit flow.

The conventional TX descriptor (WQE, Work Queue Element) serves
a single packet. Our HW has support for multi-packet WQE (MPWQE)
in which a single descriptor serves multiple TX packets.

This reduces both the PCI overhead and the CPU cycles wasted on
writing them.

In this patch we add support for the HW feature, which is supported
starting from ConnectX-5.

Performance:
Tested packet rate for UDP 64Byte multi-stream over ConnectX-5 NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz

XDP_TX:
We see a huge gain on single port ConnectX-5, and reach the 100 Mpps
milestone.
* Single-port HCA:
	Before:   70 Mpps
	After:   100 Mpps (+42.8%)

* Dual-port HCA:
	Before: 51.7 Mpps
	After:  57.3 Mpps (+10.8%)

* In both cases we tested traffic on one port and for now On Dual-port HCAs
  we see only small gain, we are working to overcome this bottleneck, but
  for the moment only with experimental firmware on dual port HCAs we can
  reach the wanted numbers as seen on Single-port HCAs.

XDP_REDIRECT:
Redirect from (A) ConnectX-5 to (B) ConnectX-5.
Due to a setup limitation, (A) and (B) are on different NUMA nodes,
so absolute performance numbers are not optimal.
Note:
  Below is the transmit rate of (B), not the redirect rate of (A)
  which is in some cases higher.

* (B) is single-port:
	Before:   77 Mpps
	After:    90 Mpps (+16.8%)

* (B) is dual-port:
	Before:  61 Mpps
	After:   72 Mpps (+18%)
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Each xdp_wqe_info instance describes the number of data-segments
and WQEBBs of the WQE.
This is useful for a downstream patch that adds support for
Multi-Packet TX WQE feature.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This provides infrastructure to have multiple xdp_info instances
for the same consumer index.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Instead of calculating the control segment to be used upon an
XDP xmit doorbell, save it in SQ structure.
Nullify when no pending doorbell.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Do not ignore the CQE opcode.
This helps expose issues and debug them.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Do not maintain an SQ state bit to indicate whether an
XDP SQ serves redirect operations.

Instead, rely on the fact that such an XDP SQ doesn't reside
in an RQ instance, while the others do.
This info is not known to the XDP SQ functions themselves,
and they rely on their callers to distinguish between the cases.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

At the end of the RQ polling loop, some XDP-related operations
might be required. Before checking them one by one, check if
an XDP program is even loaded.
Combine all the checks and operations in a single function in xdp files.

This saves unnecessary checks for non-XDP flows.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The opcode indicates about the error reason.
Printing it helps in debug.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Virtio-net devices negotiate LRO support with the host.
Display the initially negotiated state with ethtool -k.

Also allow configuring it with ethtool -K, reusing the existing
virtnet_set_guest_offloads helper that configures LRO for XDP.
This is conditional on VIRTIO_NET_F_CTRL_GUEST_OFFLOADS.

Virtio-net negotiates TSO4 and TSO6 separately, but ethtool does not
distinguish between the two. Display LRO as on only if any offload
is active.

RTNL is held while calling virtnet_set_features, same as on the path
from virtnet_xdp_set.

Changes v1 -> v2
  - allow ethtool config (-K) only if VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
  - show LRO as enabled if any LRO variant is enabled
  - do not allow configuration while XDP is active
  - differentiate current features from the capable set, to restore
    on XDP down only those features that were active on XDP up
  - move test out of VIRTIO_NET_F_CSUM/TSO branch, which is tx only
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for net-next:

1) Support for destination MAC in ipset, from Stefano Brivio.

2) Disallow all-zeroes MAC address in ipset, also from Stefano.

3) Add IPSET_CMD_GET_BYNAME and IPSET_CMD_GET_BYINDEX commands,
   introduce protocol version number 7, from Jozsef Kadlecsik.
   A follow up patch to fix ip_set_byindex() is also included
   in this batch.

4) Honor CTA_MARK_MASK from ctnetlink, from Andreas Jaggi.

5) Statify nf_flow_table_iterate(), from Taehee Yoo.

6) Use nf_flow_table_iterate() to simplify garbage collection in
   nf_flow_table logic, also from Taehee Yoo.

7) Don't use _bh variants of call_rcu(), rcu_barrier() and
   synchronize_rcu_bh() in Netfilter, from Paul E. McKenney.

8) Remove NFC_* cache definition from the old caching
   infrastructure.

9) Remove layer 4 port rover in NAT helpers, use random port
   instead, from Florian Westphal.

10) Use strscpy() in ipset, from Qian Cai.

11) Remove NF_NAT_RANGE_PROTO_RANDOM_FULLY branch now that
    random port is allocated by default, from Xiaozhou Liu.

12) Ignore NF_NAT_RANGE_PROTO_RANDOM too, from Florian Westphal.

13) Limit port allocation selection routine in NAT to avoid
    softlockup splats when most ports are in use, from Florian.

14) Remove unused parameters in nf_ct_l4proto_unregister_sysctl()
    from Yafang Shao.

15) Direct call to nf_nat_l4proto_unique_tuple() instead of
    indirection, from Florian Westphal.

16) Several patches to remove all layer 4 NAT indirections,
    remove nf_nat_l4proto struct, from Florian Westphal.

17) Fix RTP/RTCP source port translation when SNAT is in place,
    from Alin Nastac.

18) Selective rule dump per chain, from Phil Sutter.

19) Revisit CLUSTERIP target, this includes a deadlock fix from
    netns path, sleep in atomic, remove bogus WARN_ON_ONCE()
    and disallow mismatching IP address and MAC address.
    Patchset from Taehee Yoo.

20) Update UDP timeout to stream after 2 seconds, from Florian.

21) Shrink UDP established timeout to 120 seconds like TCP timewait.

22) Sysctl knobs to set GRE timeouts, from Yafang Shao.

23) Move seq_print_acct() to conntrack core file, from Florian.

24) Add enum for conntrack sysctl knobs, also from Florian.

25) Place nf_conntrack_acct, nf_conntrack_helper, nf_conntrack_events
    and nf_conntrack_timestamp knobs in the core, from Florian Westphal.
    As a side effect, shrink netns_ct structure by removing obsolete
    sysctl anchors, also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf-next 2018-12-21

The following pull-request contains BPF updates for your *net-next* tree.

There is a merge conflict in test_verifier.c. Result looks as follows:

        [...]
        },
        {
                "calls: cross frame pruning",
                .insns = {
                [...]
                .prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
                .errstr_unpriv = "function calls to other bpf functions are allowed for root only",
                .result_unpriv = REJECT,
                .errstr = "!read_ok",
                .result = REJECT,
	},
        {
                "jset: functional",
                .insns = {
        [...]
        {
                "jset: unknown const compare not taken",
                .insns = {
                        BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0,
                                     BPF_FUNC_get_prandom_u32),
                        BPF_JMP_IMM(BPF_JSET, BPF_REG_0, 1, 1),
                        BPF_LDX_MEM(BPF_B, BPF_REG_8, BPF_REG_9, 0),
                        BPF_EXIT_INSN(),
                },
                .prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
                .errstr_unpriv = "!read_ok",
                .result_unpriv = REJECT,
                .errstr = "!read_ok",
                .result = REJECT,
        },
        [...]
        {
                "jset: range",
                .insns = {
                [...]
                },
                .prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
                .result_unpriv = ACCEPT,
                .result = ACCEPT,
        },

The main changes are:

1) Various BTF related improvements in order to get line info
   working. Meaning, verifier will now annotate the corresponding
   BPF C code to the error log, from Martin and Yonghong.

2) Implement support for raw BPF tracepoints in modules, from Matt.

3) Add several improvements to verifier state logic, namely speeding
   up stacksafe check, optimizations for stack state equivalence
   test and safety checks for liveness analysis, from Alexei.

4) Teach verifier to make use of BPF_JSET instruction, add several
   test cases to kselftests and remove nfp specific JSET optimization
   now that verifier has awareness, from Jakub.

5) Improve BPF verifier's slot_type marking logic in order to
   allow more stack slot sharing, from Jiong.

6) Add sk_msg->size member for context access and add set of fixes
   and improvements to make sock_map with kTLS usable with openssl
   based applications, from John.

7) Several cleanups and documentation updates in bpftool as well as
   auto-mount of tracefs for "bpftool prog tracelog" command,
   from Quentin.

8) Include sub-program tags from now on in bpf_prog_info in order to
   have a reliable way for user space to get all tags of the program
   e.g. needed for kallsyms correlation, from Song.

9) Add BTF annotations for cgroup_local_storage BPF maps and
   implement bpf fs pretty print support, from Roman.

10) Fix bpftool in order to allow for cross-compilation, from Ivan.

11) Update of bpftool license to GPLv2-only + BSD-2-Clause in order
    to be compatible with libbfd and allow for Debian packaging,
    from Jakub.

12) Remove an obsolete prog->aux sanitation in dump and get rid of
    version check for prog load, from Daniel.

13) Fix a memory leak in libbpf's line info handling, from Prashant.

14) Fix cpumap's frame alignment for build_skb() so that skb_shared_info
    does not get unaligned, from Jesper.

15) Fix test_progs kselftest to work with older compilers which are less
    smart in optimizing (and thus throwing build error), from Stanislav.

16) Cleanup and simplify AF_XDP socket teardown, from Björn.

17) Fix sk lookup in BPF kselftest's test_sock_addr with regards
    to netns_id argument, from Andrey.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Willem de Bruijn says:

====================
expand txtimestamp selftest

Convert the existing txtimestamp test to run as part of kselftest
and return a pass/fail.

Also expand the variations of timestamping tested, including packet
sockets, ipv6 raw and dgram and passing options using cmsg.

These are enough changes to split across a few patches, even if all
changes are only this one test.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Run the transmit timestamp tests as part of kselftests.

Add a txtimestamp.sh test script that runs most variants:
ipv4/ipv6, tcp/udp/raw/raw_ipproto/pf_packet, data/nodata,
setsockopt/cmsg. The script runs tests with netem delays.

Refine txtimestamp.c to validate results. Take expected
netem delays as input and compare against real timestamps.

To run without dependencies, add a listener socket to be
able to connect in the case of TCP.

Add the timestamping directory to the kselftests Makefile.
Build all the binaries. Only run verified txtimestamp.sh.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expand the transmit timestamp regression test with support for
missing protocols: ipv6 datagram and raw and pf_packet.

Also refine resolve_hostname to independently request AF_INET or
AF_INET6 addresses. Else, ipv4 addresses may be returned as AF_INET6.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3dd17e63 ("sock: accept SO_TIMESTAMPING flags in socket
cmsg") added support for passing tx timestamping options per-call
in sendmsg.

Expand the txtimestamp test with support for this feature.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A minor code cleanup.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract "Protocol" field decompression code from transport protocols to
PPP generic layer, where it actually belongs. As a consequence, this
patch fixes incorrect place of PFC decompression in L2TP driver (when
it's not PPPOX_BOUND) and also enables this decompression for other
protocols, like PPPoE.

Protocol field decompression also happens in PPP Multilink Protocol
code and in PPP compression protocols implementations (bsd, deflate,
mppe). It looks like there is no easy way to get rid of that, so it was
decided to leave it as is, but provide those cases with appropriate
comments instead.

Changes in v2:
  - Fix the order of checking skb data room and proto decompression
  - Remove "inline" keyword from ppp_decompress_proto()
  - Don't split line before function name
  - Prefix ppp_decompress_proto() function with "__"
  - Add ppp_decompress_proto() function with skb data room checks
  - Add description for introduced functions
  - Fix comments (as per review on mailing list)
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.21

Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.

Major changes:

ath10k

* add amsdu support for QCA6174 monitor mode

* report tx rate using the new ieee80211_tx_rate_update() API

* wcn3990 support is not experimental anymore

iwlwifi

* support for FW version 43 for 9000 and 22000 series

brcmfmac

* add support for CYW43012 SDIO chipset

* add the raw 4354 PCIe device ID for unprogrammed Cypress boards

mwifiex

* add NL80211_STA_INFO_RX_BITRATE support

mt76

* use the same firmware for mt76x2e and mt76x2u

* mt76x0e survey support

* more unification between mt76x2 and mt76x0

* mt76x0e AP mode support

* mt76x0e DFS support

* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't need extern prefix before function prototypes.
Checkpatch has complained about this for a couple of years.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
net: ipv4: Prevent user triggerable warning

Patch #1 prevents a user triaggerable warning in the flow dissector by
setting 'skb->dev' in skbs used for IPv4 output route get requests.

Patch #2 adds a test case that triggers the warning without the first
patch.

I have audited all the RTM_GETROUTE handlers and could not find any
other callpath where an skb is passed to the flow dissector with both
'skb->dev' and 'skb->sk' cleared.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Without previous patch a warning would be generated upon multipath route
get when FIB multipath hash policy is to use a 5-tuple for multipath
hash calculation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When user requests to resolve an output route, the kernel synthesizes
an skb where the relevant parameters (e.g., source address) are set. The
skb is then passed to ip_route_output_key_hash_rcu() which might call
into the flow dissector in case a multipath route was hit and a nexthop
needs to be selected based on the multipath hash.

Since both 'skb->dev' and 'skb->sk' are not set, a warning is triggered
in the flow dissector [1]. The warning is there to prevent codepaths
from silently falling back to the standard flow dissector instead of the
BPF one.

Therefore, instead of removing the warning, set 'skb->dev' to the
loopback device, as its not used for anything but resolving the correct
namespace.

[1]
WARNING: CPU: 1 PID: 24819 at net/core/flow_dissector.c:764 __skb_flow_dissect+0x314/0x16b0
...
RSP: 0018:ffffa0df41fdf650 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8bcded232000 RCX: 0000000000000000
RDX: ffffa0df41fdf7e0 RSI: ffffffff98e415a0 RDI: ffff8bcded232000
RBP: ffffa0df41fdf760 R08: 0000000000000000 R09: 0000000000000000
R10: ffffa0df41fdf7e8 R11: ffff8bcdf27a3000 R12: ffffffff98e415a0
R13: ffffa0df41fdf7e0 R14: ffffffff98dd2980 R15: ffffa0df41fdf7e0
FS:  00007f46f6897680(0000) GS:ffff8bcdf7a80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055933e95f9a0 CR3: 000000021e636000 CR4: 00000000001006e0
Call Trace:
 fib_multipath_hash+0x28c/0x2d0
 ? fib_multipath_hash+0x28c/0x2d0
 fib_select_path+0x241/0x32f
 ? __fib_lookup+0x6a/0xb0
 ip_route_output_key_hash_rcu+0x650/0xa30
 ? __alloc_skb+0x9b/0x1d0
 inet_rtm_getroute+0x3f7/0xb80
 ? __alloc_pages_nodemask+0x11c/0x2c0
 rtnetlink_rcv_msg+0x1d9/0x2f0
 ? rtnl_calcit.isra.24+0x120/0x120
 netlink_rcv_skb+0x54/0x130
 rtnetlink_rcv+0x15/0x20
 netlink_unicast+0x20a/0x2c0
 netlink_sendmsg+0x2d1/0x3d0
 sock_sendmsg+0x39/0x50
 ___sys_sendmsg+0x2a0/0x2f0
 ? filemap_map_pages+0x16b/0x360
 ? __handle_mm_fault+0x108e/0x13d0
 __sys_sendmsg+0x63/0xa0
 ? __sys_sendmsg+0x63/0xa0
 __x64_sys_sendmsg+0x1f/0x30
 do_syscall_64+0x5a/0x120
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: d0e13a14 ("flow_dissector: lookup netns by skb->sk if skb->dev is NULL")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When doing indirect access in the Ocelot chip, a command is setup,
issued and then we need to poll until the result is ready. The polling
timeout is specified in milliseconds in the datasheet and not in
register access attempts.
It is not a bug on the currently supported platform, but we observed
that the code does not work properly on other platforms that we want to
support as the timing requirements there are different.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the stray semicolon means that the final term in the addition
is being missed.  Fix this by removing it. Cleans up clang warning:

net/core/neighbour.c:2821:9: warning: expression result unused [-Wunused-value]

Fixes: 82cbb5c6 ("neighbour: register rtnl doit handler")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-By: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Port partitioning is done by enabling UNICAST_VLAN_BOUNDARY and changing
the default port membership of 0x7f to other values such that there is
no communication between ports.  In KSZ9477 the member for port 1 is
0x41; port 2, 0x42; port 3, 0x44; port 4, 0x48; port 5, 0x50; and port 7,
0x60.  Port 6 is the host port.

Setting a zero value can be used to stop port from receiving.

However, when UNICAST_VLAN_BOUNDARY is disabled and the unicast addresses
are already learned in the dynamic MAC table, setting zero still allows
devices connected to those ports to communicate.  This does not apply to
multicast and broadcast addresses though.  To prevent these leaks and
make the function of port membership consistent UNICAST_VLAN_BOUNDARY
should never be disabled.

Note that UNICAST_VLAN_BOUNDARY is enabled by default in KSZ9477.

Fixes: b987e98e ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When resolving the conflict wrt. the vxlan_fdb_update call
in vxlan_changelink() I made the last argument false instead
of true.

Fix this.
Signed-off-by: David S. Miller <davem@davemloft.net>

remove the obsolete sysctl anchors and move auto_assign_helper_warned
to avoid/cover a hole.  Reduces size by 40 bytes on 64 bit.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Saeed Mahameed says:

====================
mlx5-updates-2018-12-19

This series adds some misc updates and the support for tunnels over VLAN
tc offloads.

From Miroslav Lichvar, patches #1,2
1) Update timecounter at least twice per counter overflow
2) Extend PTP gettime function to read system clock

From Gavi Teitz, patch #3
3) Increase VF representors' SQ size to 128

From Eli Britstein and Or Gerlitz, patches #4-10
4) Adds the capability to support tunnels over VLAN device.

Patch 4 avoids crash for TC flow with egress upper devices

Patch 5 refactors tunnel routing devs into a helper function

Patch 6 avoids crash for TC encap flows with vlan on underlay

Patches 7-8 refactor encap tunnel header preparing code.

Patch 9 adds support for building VLAN tagged ETH header.

Patch 10 adds support for tunnel routing to VLAN device.

From Aviv, patches 11,12 to fix earlier VF lag series
5) Fix query_nic_sys_image_guid() error during init
6) Fix LAG requirement when CONFIG_MLX5_ESWITCH is off
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

after moving sysctl handling into single place, the init functions
can't fail anymore and some of the fini functions are empty.

Remove them and change return type to void.
This also simplifies error unwinding in conntrack module init path.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Similar to previous change, this time for eache and timestamp.
Unlike helper and acct, these can be disabled at build time, so they
need ifdef guards.

Next patch will remove a few (now obsolete) functions.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Needless copy&paste, just handle all in one.  Next patch will handle
acct and timestamp, which have similar functions.

Intentionally leaves cruft behind, will be cleaned up in a followup
patch.

The obsolete sysctl pointers in netns_ct struct are left in place and
removed in a single change, as changes to netns trigger rebuild of
almost all files.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Its a bit hard to see what table[3] really lines up with, so add
human-readable mnemonics and use them for initialisation.

This makes it easier to see e.g. which sysctls are not exported to
unprivileged userns.

objdiff shows no changes.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Only one caller, just place it where its needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This patch adds two sysctl knobs for GRE:

	net.netfilter.nf_conntrack_gre_timeout = 30
	net.netfilter.nf_conntrack_gre_timeout_stream = 180

Update the Documentation as well.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Ido Schimmel says:

====================
mlxsw: Two usability improvements

This patchset contains two small improvements in the mlxsw driver. The
first one, in patches #1-#2, relieves the user from the need to
configure a VLAN interface and only later the corresponding VXLAN
tunnel. The issue is explained in detail in the first patch.

The second improvement is described below and allows the user to make
use of VID 1 by having the driver use the reserved 4095 VID for untagged
traffic.

VLAN entries on a given port can be associated with either a bridge or a
router. For example, if swp1.10 is assigned an IP address and swp1.20 is
enslaved to a VLAN-unaware bridge, then both {Port 1, VID 10} and {Port
1, VID 20} would be associated with a filtering identifier (FID) of the
correct type.

In case swp1 itself is assigned an IP address or enslaved to a
VLAN-unaware bridge, then a FID would be associated with {Port 1, VID
1}. Using VID 1 for this purpose means that VLAN devices with VID 1
cannot be created over mlxsw ports, as this VID is (ab)used as the
default VLAN.

Instead of using VID 1 for this purpose, we can use VID 4095 which is
reserved for internal use and cannot be configured by either the 8021q
or the bridge driver.

Patches #3-#7 perform small and non-functional changes that finally
allow us to switch to VID 4095 as the default VID in patch #8.

Patch #9 removes the limitation about creation of VLAN devices with VID
1 over mlxsw ports.

Patches #10-#11 add test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous patches made it possible to setup VLAN devices with VID 1 over
mlxsw ports. Verify this functionality actually works by conducting a
simple router test over VID 1.

Adding this test as a generic test since it can be run using veth pairs
and it can also be useful for other physical devices where VID 1 was
considered reserved (knowingly or not).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous patches made it possible to create VLAN devices with VID 1 over
mlxsw ports. Adjust the test to verify such an operation succeeds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VID 1 is not reserved anymore, so remove the check that prevented the
creation of VLAN devices with this VID over mlxsw ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to abuse VID 1 anymore and we can instead use VID 4095
as the default VLAN, which will be configured on the port throughout its
lifetime.

The OVS join / leave functions are changed to enable VIDs 1-4094
(inclusive) instead of 2-4095. This because VID 4095 is now the default
VLAN instead of 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN entries on a port can be associated with either a bridge VLAN or a
router port. Before the VLAN entry is destroyed these associations need
to be cleaned up.

Currently, this is always invoked from the function which destroys the
VLAN entry, but next patch is going to skip the destruction of the
default entry when a port in unlinked from a LAG.

The above does not mean that the associations should not be cleaned up,
so add a helper that will be invoked from both call sites.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>