Since commit d6580a9f ("kexec: sysrq: simplify sysrq-c handler"),
the sysrq handler for the 'c' key has been sysrq_crash_op.  Debugging
code in the ibm_emac driver also tries to register a handler for the 'c'
key, but this has no effect because register_sysrq_key() doesn't replace
existing handlers.  Since evidently no one has cared enough to fix this
in the last 8 years, and it's very rare for drivers to register sysrq
handlers (for good reason), just remove the dead code.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Earlier patch c4adfc82 ("bonding: make speed, duplex setting
consistent with link state") made an attempt to keep slave state
consistent with speed and duplex settings. Unfortunately link-state
transition is used to change the active link especially when used
in conjunction with mii-mon. The above mentioned patch broke that
logic. Also when speed and duplex settings for a link are updated
during a link-event, the link-status should not be changed to
invoke correct transition logic.

This patch fixes this issue by moving the link-state update outside
of the bond_update_speed_duplex() fn and to the places where this fn
is called and update link-state selectively.

Fixes: c4adfc82 ("bonding: make speed, duplex setting consistent
with link state")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

cb_running is reported in /proc/self/net/netlink and it is reported by
the ss tool, when it gets information from the proc files.

sock_diag is a new interface which is used instead of proc files, so it
looks reasonable that this interface has to report no less information
about sockets than proc files.

We use these flags to dump and restore netlink sockets.
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should be returning -ENOMEM if qed_mcp_cmd_add_elem() fails.  The
current code returns success.

Fixes: 4ed1eea8 ("qed: Revise MFW command locking")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We accidentally left this dead code behind after commit 5952fde1
("net: sched: choke: remove dead filter classify code").
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a cut and paste bug here so we accidentally clear the first
few bytes of "resp" a second time instead clearing "ctx".

Fixes: 50c0add5 ("liquidio: refactor interrupt moderation code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In hardware configurations where multiple queues are active,
the rx queue needs to be mapped into a dma channel, even if
a single rx queue is used.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add all the currently available SPEED_<foo> strings.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Updates for net-next.

Main changes are to add WoL and selftest features, optimize XDP_TX by
using short BDs, and to cap the usage of MSIX.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code enables up to the maximum MSIX vectors in the PCIE
config space without considering the max completion rings available.
An MSIX vector is only useful when it has an associated completion
ring, so it is better to cap it.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No offload is performed on the XDP_TX ring so we can use the short TX
BDs.  This has the effect of doubling the size of the XDP TX ring so
that it now matches the size of the rx ring by default.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is necessary to disable autoneg before enabling PHY loopback,
otherwise link won't come up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mac loopback self test operates in polling mode.  To support that,
we need to add functions to open and close the NIC half way.  The half
open mode allows the rings to operate without IRQ and NAPI.  We
use the XDP transmit function to send the loopback packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the basic infrastructure and only firmware tests initially.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add suspend/resume callbacks using the newer dev_pm_ops method.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

And add functions to set and free magic packet filter.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add pci shutdown method to put device in the proper WoL and power state.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add code to driver probe function to check if the device is WoL capable
and if Magic packet WoL filter is currently set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Features added include WoL and selftest.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2017-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.11

iwlwifi

* an RCU fix
* a fix for a potential out-of-bounds access crash
* a fix for IBSS which has been broken since DQA was enabled

rtlwifi

* fix scheduling while atomic regression

brcmfmac

* fix use-after-free bug found by KASAN
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed: QM & ILT changes

This series introduces several changes and improvements to existing
queue manager and ILT configurations done during initialization.
Notice some of the patches are actually future fixes, I.e., bugs that
can't be triggered with exisiting driver but are needed for some future
functionality.

Patch #1 refactors the configuration of the hardware's queue manager,
which is quite messy today. This contains most of the bulk [code-wise]
in the series.

Patch #2, #3 fix Timers related ILT configurations that are yet to
affect qed in existing scenarios.

Patch #4 reduces needless ILT lines wasted for RoCE configurations.

Patch #5 allows RoCE partitions to manage with less memory regions
[important, e.g., for Multi-function parititions with RoCE support].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It's possible some configurations would prevent driver from utilizing
all the Memory Regions due to a lack of ILT lines.
In such a case, calculate how many memory regions would have to be
dropped due to limit, and manage without those.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As RoCE doesn't need to use the SRC, allocating ILT memory
on behalf of RoCE is wasting available ILT lines.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As of today there's no protocol supported that requires
support from the TM hardware block and enables SRIOV,
but we should still correct the calculation to reflect
the lines required for such future VFs instead of changing
the PF's own lines.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When configuring the HW timers block we should set the number of CIDs
up until the last CID that require timers, instead of only those CIDs
whose protocol needs timers support.

Today, the protocols that require HW timers' support have their CIDs
before any other protocol, but that would change in future [when we
add iWARP support].
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor and clean up the queue manager initialization logic.
Also, this adds support for RoC low latency queues, which later
would be used for improving RoCE latency in high throughput scenarios.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the net stats64 counters to the usbnet core. With that
in place put the hooks into every usbnet driver to use it.

This is a strait forward addition of 64bit counters for RX and TX packet
and byte counts. It is done in the same style as for the other net drivers
that support stats64. Note that the other stats fields remain as 32bit
sized values (error counts, etc).

The motivation to add this is that it is not particularly difficult to
get the RX and TX byte counts to wrap on 32bit platforms.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Number of sockets is limited by 16-bit, so 64-bit allocation will never
happen.

16-bit ops are the worst code density-wise on x86_64 because of
additional prefix (66).

Space savings:

	add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-3 (-3)
	function                                     old     new   delta
	reuseport_add_sock                           539     536      -3
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make ->hash_count, ->low_watermark and ->high_watermark unsigned int
and propagate unsignedness to other variables.

This change doesn't change code generation because these fields aren't
used in 64-bit contexts but make it anyway: these fields can't be
negative numbers.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hash size can't negative so "unsigned int" is logically correct.

Propagate "unsigned int" to loop counters.

Space savings:

	add/remove: 0/0 grow/shrink: 2/2 up/down: 6/-18 (-12)
	function                                     old     new   delta
	flow_cache_flush_tasklet                     362     365      +3
	__flow_cache_shrink                          333     336      +3
	flow_cache_cpu_up_prep                       178     171      -7
	flow_cache_lookup                           1159    1148     -11
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flow keys aren't 4GB+ numbers so 64-bit arithmetic is excessive.

Space savings (I'm not sure what CSWTCH is):

	add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-48 (-48)
	function                                     old     new   delta
	flow_cache_lookup                           1163    1159      -4
	CSWTCH                                     75997   75953     -44
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Breaking the include loop netdevice.h, dsa.h, devlink.h broke this
driver, it depends on includes brought in by these headers. Adding
linux/of.h fixes it.

Fixes: ed0e39e97d34 ("net: break include loop netdevice.h, dsa.h, devlink.h")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an incoming frame is tagged or when GRO is disabled, the skb
handled to vxlan_xmit() doesn't contain a valid transport header
offset. This makes ND proxying fail.

We combine two changes: replace use of skb_transport_offset() and ensure
the necessary amount of skb is linear just before using it:

 - In vxlan_xmit(), when determining if we have an ICMPv6 neighbor
   discovery packet, just check if it is an ICMPv6 packet and rely on
   neigh_reduce() to do more checks if this is the case. The use of
   pskb_may_pull() is replaced by skb_header_pointer() for just the IPv6
   header.

 - In neigh_reduce(), add pskb_may_pull() for IPv6 header and neighbor
   discovery message since this was removed from vxlan_xmit(). Replace
   skb_transport_header() with ipv6_hdr() + 1.

 - In vxlan_na_create(), replace first skb_transport_offset() with
   ipv6_hdr() + 1 and second with skb_network_offset() + sizeof(struct
   ipv6hdr). Additionally, ensure we pskb_may_pull() the whole skb as we
   need it to iterate over the options.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before when implementing sctp prsctp, SCTP_PR_STREAM_STATUS wasn't
added, as it needs to save abandoned_(un)sent for every stream.

After sctp stream reconf is added in sctp, assoc has structure
sctp_stream_out to save per stream info.

This patch is to add SCTP_PR_STREAM_STATUS by putting the prsctp
per stream statistics into sctp_stream_out.

v1->v2:
  fix an indent issue.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Salil Mehta says:

====================
net: hns: Misc. HNS Bug Fixes & Code Improvements

This patch set introduces various HNS bug fixes, optimizations and code
improvements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes some checkpatch.pl script caught errors and
warnings during the compilation time.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a bug on Hip06 that tx ring interrupts packets count will be
clear when drivers send data to tx ring, so that the tx packets count
will never upgrade to packets line, and cause the interrupts engendered
was delayed.
Sometimes, it will cause sending performance lower than expected.

To fix this bug, we set tx ring interrupts packets line to 1 forever,
to avoid count clear. And set the gap time to 20us, to solve the problem
that too many interrupts engendered when packets line is 1.

This patch could advance the send performance on ARM  from 6.6G to 9.37G
when an iperf send thread on ARM and an iperf send thread on X86 for XGE.
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HNS needs SMB Buffers to store at least two packets after sending
pause frame because of the link delay. The MTU of HNS is 9728. As
the processor user manual described, the SBM buffer threshold should
be modified.
Reported-by: Ping Zhang <zhangping5@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>