This patch registers callbacks to support HTB offload.

Below are features supported,

- supports traffic shaping on the given class by honoring rate and ceil
configuration.

- supports traffic scheduling,  which prioritizes different types of
traffic based on strict priority values.

- supports the creation of leaf to inner classes such that parent node
rate limits apply to all child nodes.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves rate limiting definitions to a common header file and
adds csr definitions required for QOS code.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Upon txschq free request, the transmit schedular config in hardware
is not getting reset. This patch adds necessary changes to do the same.

2. Current implementation calls txschq alloc during interface
initialization and in response handler updates the default txschq array.
This creates a problem for htb offload where txsch alloc will be called
for every tc class. This patch addresses the issue by reading txschq
response in mbox caller function instead in the response handler.

3. Current otx2_txschq_stop routine tries to free all txschq nodes
allocated to the interface. This creates a problem for htb offload.
This patch introduces the otx2_txschq_free_one to free txschq in a
given level.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current implementation is such that the number of Send queues (SQs)
are decided on the device probe which is equal to the number of online
cpus. These SQs are allocated and deallocated in interface open and c
lose calls respectively.

This patch defines new APIs for initializing and deinitializing Send
queues dynamically and allocates more number of transmit queues for
QOS feature.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

current implementation is such that tot_tx_queues contains both
xdp queues and normal tx queues. which will be allocated in interface
open calls and deallocated on interface down calls respectively.

With addition of QOS, where send quees are allocated/deallacated upon
user request Qos send queues won't be part of tot_tx_queues. So this
patch renames tot_tx_queues to non_qos_queues.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current implementation of HTB offload returns the EINVAL error
for unsupported parameters like prio and quantum. This patch removes
the error returning checks for 'prio' parameter and populates its
value to tc_htb_qopt_offload structure such that driver can use the
same.

Add prio parameter check in mlx5 driver, as mlx5 devices are not capable
of supporting the prio parameter when htb offload is used. Report error
if prio parameter is set to a non-default value.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Co-developed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As low_thresh has no work in fragment reassembles,del it.
And Mark it deprecated in sysctl Document.
Signed-off-by: Angus Chen <angus.chen@jaguarmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-next-2023-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Kalle valo says:

====================
wireless-next patches for v6.5

The first pull request for v6.5 and only driver changes this time.
rtl8xxxu has been making lots of progress lately and now has AP mode
support.

Major changes:

rtl8xxxu

* AP mode support, initially only for rtl8188f

rtw89

* provide RSSI, EVN and SNR statistics via debugfs

* support U-NII-4 channels on 5 GHz band
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When writing error messages to extack for pseudo collisions, we can't
 use encap->type as encap has already been freed.  Fortunately the
 same value is stored in local variable em_type, so use that instead.

Fixes: 3c9561c0 ("sfc: support TC decap rules matching on enc_ip_tos")
Reported-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both phylink_create() and phylink_fwnode_phy_connect() do not modify
the fwnode argument that they are passed, so lets constify these.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch standardizes the inconsistent return values for unsuccessful
XDP transmits by using standardized error codes (-EBUSY or -ENOMEM).
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On mpfs, with SRAM configured for 4 queues, setting max_tx_len
to GEM_TX_MAX_LEN=0x3f0 results multiple AMBA errors.
Setting max_tx_len to (4KiB - 56) removes those errors.

The details are described in erratum 1686 by Cadence

The max jumbo frame size is also reduced for mpfs to (4KiB - 56).
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since introduced in commit c319b4d7 ("net: ipv4: add IPPROTO_ICMP
socket kind"), ping socket does not use SLAB_TYPESAFE_BY_RCU nor check
nulls marker in loops.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yunsheng Lin says:

====================
net: introduce skb_frag_fill_page_desc()

Most users use __skb_frag_set_page()/skb_frag_off_set()/
skb_frag_size_set() to fill the page desc for a skb frag.
It does not make much sense to calling __skb_frag_set_page()
without calling skb_frag_off_set(), as the offset may depend
on whether the page is head page or tail page, so add
skb_frag_fill_page_desc() to fill the page desc for a skb
frag.

In the future, we can make sure the page in the frag is
head page of compound page or a base page, if not, we
may warn about that and convert the tail page to head
page and update the offset accordingly, if we see a warning
about that, we also fix the caller to fill the head page
in the frag. when the fixing is done, we may remove the
warning and converting.

In this way, we can remove the compound_head() or use
page_ref_*() like the below case:
https://elixir.bootlin.com/linux/latest/source/net/core/page_pool.c#L881
https://elixir.bootlin.com/linux/latest/source/include/linux/skbuff.h#L3383

It may also convert net stack to use the folio easier.

V1: repost with all the ack/review tags included.
RFC: remove a local variable as pointed out by Simon.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The remaining users calling __skb_frag_set_page() with
page being NULL seems to be doing defensive programming,
as shinfo->nr_frags is already decremented, so remove
them.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most users use __skb_frag_set_page()/skb_frag_off_set()/
skb_frag_size_set() to fill the page desc for a skb frag.

Introduce skb_frag_fill_page_desc() to do that.

net/bpf/test_run.c does not call skb_frag_off_set() to
set the offset, "copy_from_user(page_address(page), ...)"
and 'shinfo' being part of the 'data' kzalloced in
bpf_test_init() suggest that it is assuming offset to be
initialized as zero, so call skb_frag_fill_page_desc()
with offset being zero for this case.

Also, skb_frag_set_page() is not used anymore, so remove
it.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add test to make sure that the localbypass option is on by default.

Add test to change vxlan localbypass to nolocalbypass and check
that packets are delivered to userspace.
Signed-off-by: Vladimir Nikishkin <vladimir@nikishkin.pw>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a packet needs to be encapsulated towards a local destination IP, the
packet will undergo a "local bypass" and be injected into the Rx path as
if it was received by the target VXLAN device without undergoing
encapsulation. If such a device does not exist, the packet will be
dropped.

There are scenarios where we do not want to perform such a bypass, but
instead want the packet to be encapsulated and locally received by a
user space program for post-processing.

To that end, add a new VXLAN device attribute that controls whether a
"local bypass" is performed or not. Default to performing a bypass to
maintain existing behavior.
Signed-off-by: Vladimir Nikishkin <vladimir@nikishkin.pw>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
Support for Wake-on-LAN for Broadcom PHYs

This patch series adds support for Wake-on-LAN to the Broadcom PHY
driver. Specifically the BCM54210E/B50212E are capable of supporting
Wake-on-LAN using an external pin typically wired up to a system's GPIO.

These PHY operate a programmable Ethernet MAC destination address
comparator which will fire up an interrupt whenever a match is received.
Because of that, it was necessary to introduce patch #1 which allows the
PHY driver's ->suspend() routine to be called unconditionally. This is
necessary in our case because we need a hook point into the device
suspend/resume flow to enable the wake-up interrupt as late as possible.

Patch #2 adds support for the Broadcom PHY library and driver for
Wake-on-LAN proper with the WAKE_UCAST, WAKE_MCAST, WAKE_BCAST,
WAKE_MAGIC and WAKE_MAGICSECURE. Note that WAKE_FILTER is supportable,
however this will require further discussions and be submitted as a RFC
series later on.

Patch #3 updates the GENET driver to defer to the PHY for Wake-on-LAN if
the PHY supports it, thus allowing the MAC to be powered down to
conserve power.

Changes in v3:

- collected Reviewed-by tags
- explicitly use return 0 in bcm54xx_phy_probe() (Paolo)

Changes in v2:

- introduce PHY_ALWAYS_CALL_SUSPEND and only have the Broadcom PHY
  driver set this flag to minimize changes to the suspend flow to only
  drivers that need it

- corrected possibly uninitialized variable in bcm54xx_set_wakeup_irq
  (Simon)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If available, interrogate the PHY to find out whether we can use it for
Wake-on-LAN. This can be a more power efficient way of implementing
that feature, especially when the MAC is powered off in low power
states.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for WAKE_UCAST, WAKE_MCAST, WAKE_BCAST, WAKE_MAGIC and
WAKE_MAGICSECURE. This is only supported with the BCM54210E and
compatible Ethernet PHYs. Using the in-band interrupt or an out of band
GPIO interrupts are supported.

Broadcom PHYs will generate a Wake-on-LAN level low interrupt on LED4 as
soon as one of the supported patterns is being matched. That includes
generating such an interrupt even if the PHY is operated during normal
modes. If WAKE_UCAST is selected, this could lead to the LED4 interrupt
firing up for every packet being received which is absolutely
undesirable from a performance point of view.

Because the Wake-on-LAN configuration can be set long before the system
is actually put to sleep, we cannot have an interrupt service routine to
clear on read the interrupt status register and ensure that new packet
matches will be detected.

It is desirable to enable the Wake-on-LAN interrupt as late as possible
during the system suspend process such that we limit the number of
interrupts to be handled by the system, but also conversely feed into
the Linux's system suspend way of dealing with interrupts in and around
the points of no return.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A few PHY drivers are currently attempting to not suspend the PHY when
Wake-on-LAN is enabled, however that code is not currently executing at
all due to an early check in phy_suspend().

This prevents PHY drivers from making an appropriate decisions and put
the hardware into a low power state if desired.

In order to allow the PHY drivers to opt into getting their ->suspend
routine to be called, add a PHY_ALWAYS_CALL_SUSPEND bit which can be
set. A boolean that tracks whether the PHY or the attached MAC has
Wake-on-LAN enabled is also provided for convenience.

If phydev::wol_enabled then the PHY shall not prevent its own
Wake-on-LAN detection logic from working and shall not prevent the
Ethernet MAC from receiving packets for matching.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Edward Cree says:

====================
sfc: more flexible encap matches on TC decap rules

This series extends the TC offload support on EF100 to support optionally
 matching on the IP ToS and UDP source port of the outer header in rules
 performing tunnel decapsulation.  Both of these fields allow masked
 matches if the underlying hardware supports it (current EF100 hardware
 supports masking on ToS, but only exact-match on source port).
Given that the source port is typically populated from a hash of inner
 header entropy, it's not clear whether filtering on it is useful, but
 since we can support it we may as well expose the capability.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow efx_tc_encap_match entries to include a udp_sport and a
 udp_sport_mask.  As with enc_ip_tos, use pseudos to enforce that all
 encap matches within a given <src_ip,dst_ip,udp_dport> tuple have
 the same udp_sport_mask.
Note that since we use a single layer of pseudos for both fields, two
 matches that differ in (say) udp_sport value aren't permitted to have
 different ip_tos_mask, even though this would technically be safe.
Current userland TC does not support setting enc_src_port; this patch
 was tested with an iproute2 patched to support it.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow efx_tc_encap_match entries to include an ip_tos and ip_tos_mask.
To avoid partially-overlapping Outer Rules (which can lead to undefined
 behaviour in the hardware), store extra "pseudo" entries in our
 encap_match hashtable, which are used to enforce that all Outer Rule
 entries within a given <src_ip,dst_ip,udp_dport> tuple (or IPv6
 equivalent) have the same ip_tos_mask.
The "direct" encap_match entry takes a reference on the "pseudo",
 allowing it to be destroyed when all "direct" entries using it are
 removed.
efx_tc_em_pseudo_type is an enum rather than just a bool because in
 future an additional pseudo-type will be added to support Conntrack
 offload.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently tc.c will block them before they get here, but following
 patch will change that.
Use the extack message from efx_mae_check_encap_match_caps() instead
 of writing a new one, since there's now more being fed in than just
 an IP version.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When force-freeing leftover entries from our match_action_ht, call
 efx_tc_delete_rule(), which releases all the rule's resources, rather
 than open-coding it.  The open-coded version was missing a call to
 release the rule's encap match (if any).
It probably doesn't matter as everything's being torn down anyway, but
 it's cleaner this way and prevents further error messages potentially
 being logged by efx_tc_encap_match_free() later on.
Move efx_tc_flow_free() further down the file to avoid introducing a
 forward declaration of efx_tc_delete_rule().

Fixes: 17654d84 ("sfc: add offloading of 'foreign' TC (decap) rules")
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointer variables of void * type do not require type cast.
Signed-off-by: wuych <yunchuan@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement ->bpf_bypass_getsockopt proto callback and filter out
SCTP_SOCKOPT_PEELOFF, SCTP_SOCKOPT_PEELOFF_FLAGS and SCTP_SOCKOPT_CONNECTX3
socket options from running eBPF hook on them.

SCTP_SOCKOPT_PEELOFF and SCTP_SOCKOPT_PEELOFF_FLAGS options do fd_install(),
and if BPF_CGROUP_RUN_PROG_GETSOCKOPT hook returns an error after success of
the original handler sctp_getsockopt(...), userspace will receive an error
from getsockopt syscall and will be not aware that fd was successfully
installed into a fdtable.

As pointed by Marcelo Ricardo Leitner it seems reasonable to skip
bpf getsockopt hook for SCTP_SOCKOPT_CONNECTX3 sockopt too.
Because internaly, it triggers connect() and if error is masked
then userspace will be confused.

This patch was born as a result of discussion around a new SCM_PIDFD interface:
https://lore.kernel.org/all/20230413133355.350571-3-aleksandr.mikhalitsyn@canonical.com/

Fixes: 0d01da6a ("bpf: implement getsockopt and setsockopt hooks")
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: linux-sctp@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Suggested-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Guillaume Nault says:

====================
selftests: fcnal: Test SO_DONTROUTE socket option.

The objective is to cover kernel paths that use the RTO_ONLINK flag
in .flowi4_tos. This way we'll be able to safely remove this flag in
the future by properly setting .flowi4_scope instead. With these
selftests in place, we can make sure this won't introduce regressions.

For more context, the final objective is to convert .flowi4_tos to
dscp_t, to ensure that ECN bits don't influence route and fib-rule
lookups (see commit a410a0cf ("ipv6: Define dscp_t and stop taking
ECN bits into account in fib6-rules")).

These selftests only cover IPv4, as SO_DONTROUTE has no effect on IPv6
sockets.

v2:
  - Use two different nettest options for setting SO_DONTROUTE either
    on the server or on the client socket.

  - Use the above feature to run a single 'nettest -B' instance per
    test (instead of having two nettest processes for server and
    client).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use ping -r to test the kernel behaviour with raw and ping sockets
having the SO_DONTROUTE option.

Since ipv4_ping_novrf() is called with different values of
net.ipv4.ping_group_range, then it tests both raw and ping sockets
(ping uses ping sockets if its user ID belongs to ping_group_range
and raw sockets otherwise).

With both socket types, sending packets to a neighbour (on link) host,
should work. When the host is behind a router, sending should fail.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use nettest --client-dontroute to test the kernel behaviour with UDP
sockets having the SO_DONTROUTE option. Sending packets to a neighbour
(on link) host, should work. When the host is behind a router, sending
should fail.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use nettest --{client,server}-dontroute to test the kernel behaviour
with TCP sockets having the SO_DONTROUTE option. Sending packets to a
neighbour (on link) host, should work. When the host is behind a
router, sending should fail.

Client and server sockets are tested independently, so that we can
cover different TCP kernel paths.

SO_DONTROUTE also affects the syncookies path. So ipv4_tcp_dontroute()
is made to work with or without syncookies, to cover both paths.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add --client-dontroute and --server-dontroute options to nettest. They
allow to set the SO_DONTROUTE option to the client and server sockets
respectively. This will be used by the following patches to test
the SO_DONTROUTE kernel behaviour with TCP and UDP.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The type of the vlan_proto field is __be16.
And most users of the field use it as such.

In the case of setting or testing the field for the special VLAN_N_VID
value, host byte order is used. Which seems incorrect.

It also seems somewhat odd to store a VLAN ID value in a field that is
otherwise used to store Ether types.

Address this issue by defining BOND_VLAN_PROTO_NONE, a big endian value.
0xffff was chosen somewhat arbitrarily. What is important is that it
doesn't overlap with any valid VLAN Ether types.

I don't believe the problems described above are a bug because
VLAN_N_VID in both little-endian and big-endian byte order does not
conflict with any supported VLAN Ether types in big-endian byte order.

Reported by sparse as:

 .../bond_main.c:2857:26: warning: restricted __be16 degrades to integer
 .../bond_main.c:2863:20: warning: restricted __be16 degrades to integer
 .../bond_main.c:2939:40: warning: incorrect type in assignment (different base types)
 .../bond_main.c:2939:40:    expected restricted __be16 [usertype] vlan_proto
 .../bond_main.c:2939:40:    got int

No functional changes intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Chuck Lever says:

====================
Bug fixes for net/handshake

Please consider these for merge via net-next.

Paolo observed that there is a possible leak of sock->file. I
haven't looked into that yet, but it seems to be separate from
the fixes in this series, so no need to hold these up.

Changes since v2:
- Address Paolo comment regarding handshake_dup()

Changes since v1:
- Rework "Fix handshake_dup() ref counting"
- Unpin sock->file when a handshake is cancelled
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable the upper layer protocol to specify the SNI peername. This
avoids the need for tlshd to use a DNS lookup, which can return a
hostname that doesn't match the incoming certificate's SubjectName.

Fixes: 2fd55320 ("net/handshake: Add a kernel API for requesting a TLSv1.3 handshake")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If user space never calls DONE, sock->file's reference count remains
elevated. Enable sock->file to be freed eventually in this case.
Reported-by: Jakub Kacinski <kuba@kernel.org>
Fixes: 3b3009ea ("net/handshake: Create a NETLINK service for handling handshake requests")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 3b3009ea ("net/handshake: Create a NETLINK service for handling handshake requests")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

trace_handshake_cmd_done_err() simply records the pointer in @req,
so initializing it to NULL is sufficient and safe.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 3b3009ea ("net/handshake: Create a NETLINK service for handling handshake requests")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>